How to configure Multiple PPTP VPN Clients on cisco 3g supported Router

I want the router to be a PPTP VPN client to 2 independent PPTP servers, both are in different cities in Cisco routers. I have tested with one on cisco 1841 aqnd its working fine; but when I add the 2nd, its using vpdn-group 1 and therefore connecting to the wrong PPTP server:
here is the config for the one that works:
vpdn-group 1
request-dialin
protocol pptp
rotary-group 0
initiate-to ip xxx.xxx.xxx.xxx
interface Dialer0
mtu 1450
ip address negotiated
ip pim dense-mode
ip nat outside
ip virtual-reassembly
zone-member security private
encapsulation ppp
ip igmp query-interval 125
dialer in-band
dialer idle-timeout 0
dialer string 123
dialer vpdn
dialer-group 1
no peer neighbor-route
no cdp enable
ppp pfc local request
ppp pfc remote apply
ppp encrypt mppe auto
ppp authentication ms-chap-v2 ms-chap eap chap pap callin
ppp eap refuse
ppp chap hostname xxx@xxx
ppp chap password 7 xxxpassword
But if I create a vpdn-group 2 and a Dialer1 interface, with dialer-group 2, its still attempting to connect to the IP in vpdn-group 1 - how do I get it to use the 2nd vpdn-group, or how do I make this work? and which cisco 3G Router you prefer because these are remote sites and only 3G Internet service is available.

Similar Messages

How to Configure Multiple Portal Middle Tiers with a Load Balancing Router

Hi,
Portal version trying to install 10.1.2 on Windows 2003 boxes.
I am following the guide http://download.oracle.com/docs/cd/B14099_19/portal.1012/b14037/cg_advnc.htm#i1046354. I have InfraStructure installed on a different box and am trying to install 2 Portal Midtiers each on separate boxes and using LBR. The above document is kind of confusing as I am trying to following
5.3.1 Step 1: Install a Single Portal and Wireless Middle Tier (M1)
5.3.2 Step 2: Configure OracleAS Portal on M1 to Be Accessed Through the LBR (AND FOLLOW ARE THE STEPS 1 to 14 in sequence)
if I follow 1 to 14 steps in sequence the information is not consistent what is being listed in the following sections
5.4.1 Create Virtual Hosts
5.4.2 Configure OracleAS Web Cache
5.4.3 Register OracleAS Portal with OracleAS Single Sign-On
i.e.
ptlconfig -dad portal -sso -host www.abc.com -port 7779
ptlconfig -dad portal -sso -host www.xyz.com -port 7779
as in the above steps it says to run
ptlconfig -dad portal -wc -site
and ssoreg command that always fails because I am running it from midtier as it gives error saying invalid username/password
as oppoesed to steps listed in point 8, 9, 10, 11 and 12.
Can someone please privide the steps in sequence I need to follow when installing 2 midtiers with frontend LBR and one infrastructure. I am trying to follow the architecture listed in the above link.
Any help is really appreciated.
Thanks

Hi,
Will appreciate any inputs on the following.
I am planning to install Infrastructure and one Midtier BI Forms Reports Discoverer, Portal on one windows box and the second midtier BI Forms Discoverer, Portal on the second windows box.
Please correct me if I am wrong on installing and configuring the mid-tiers as following are the steps I have compiled going through the document and want to make sure this time I do it right.
As I'll be installing BI Forms Reports Discoverer, Portal so wondering when I install the second midtier do I need to unselect all Portal, Forms, Reports, Discoverer or just the Portal I need to unselect.
Also in the host file of both the windows boxes do I just need to keep the LBR IP Address entry and remove the rest.
LBR:_
Computer Name: bigip5.prd.com
IP Address: *167.123.2.5*
Listen Port: *80*
Invaidation Port: *9401*
Infrastructure:_
Computer Name: portal1.prd.com
IP Address: *167.123.2.6*
Oracle HTTP Server Listening Port: *7777*
Application Server Control port: *1800*
M1 (Portal & BI Forms Reports Discoverer):_
Computer Name: portal1.prd.com
IP Address: *167.123.2.6*
Oracle HTTP Server Listening Port: *7778*
OracleAS Web Cache Listening Port: *80*
OracleAS Web Cache Invalidation Port: *9401*
OracleAS Web Cache Administration Port: *9400*
Web Cache Statistics port: *9402*
Application Server Control port: *1810*
M2 (Portal & BI Forms Reports Discoverer):_
Computer Name: portal2.prd.com
IP Address: *167.123.2.7*
Oracle HTTP Server Listening Port: *7778*
OracleAS Web Cache Listening Port: *80*
OracleAS Web Cache Invalidation Port: *9401*
OracleAS Web Cache Administration Port: *9400*
Web Cache Statistics port: *9402*
Application Server Control port: *1810*
First to create MetadataRepository and then Install Infrastructure and then follow the below steps to install Midtiers
Install and Configure of M1 (Portal and BI Forms Reports Discoverer):-_
*5.3.1 Step 1*: Install a Single Portal and BI Forms Reports Discoverer (M1 i.e. portal1.prd.com)
*5.3.2 Step 2*: Configure OracleAS Portal and BI Forms Reports Discoverer on M1 to Be Accessed Through the LBR
*1.* Configure LBR
*2.* Follow Section 5.4.1.1 to create the Virtual Host for bigip5.prd.com (LBR) and portal1.prd.com (M1)
*3.* Define a site that matches the virtual host entry for bigip5.prd.com (LBR) on Webcache of M1
*4.* Use OracleAS Web Cache Manager on M1, to map the site bigip5.prd.com (LBR) to middle tier portal1.prd.com (M1).
Follow steps 5 and 6 as per the document
*7.* Configure bigip5.prd.com (LBR) to accept invalidation requests from the OracleAS Metadata Repository on a separate port i.e. 9401
*8.* Change iasconfig.xml on M1
*9.* run ptlconfig -encrypt
*10.* Register the URL changes with OracleAS Portal by running ptlconfig -dad portal -wc -site
*11.* No need as it is http only
*12.* Run the follwoing
MID_TIER_ORACLE_HOME_M1\sso\bin\ssoreg.bat
-site_name bigip5.prd.com
-mod_osso_url http://bigip5.prd.com:80
-config_mod_osso TRUE
-oracle_home_path MID_TIER_ORACLE_HOME_M1
-config_file MID_TIER_ORACLE_HOME_M1\Apache\Apache\conf\osso\osso.conf
-admin_info cn=orcladmin
-virtualhost
*13.* Edit targets.xml to enable monitoring of the LBR's front-end host and port settings for OracleAS Portal
+<Property NAME="PortalListeningHostPort" VALUE=http://bigip5.prd.com:80/>+ and then run
MID_TIER_ORACLE_HOME_M1\bin\emctl reload
*14.* Test the setup
Install and Configure of M2 (Portal and BI Forms Reports Discoverer):-_
*5.3.4 Step 4*: Install a Single Portal and BI Forms Reports Discoverer (M2 i.e. portal2.prd.com)
*1.* As I am installing on wiondows so will not set IASCONFIG_LOC environment variable as I can just copy the iasconfig.xml file from M1 to M2
*2.* Run OUI on M2
*3.* Clear the selection for OracleAS Portal but don't know if I need to unselect Forms , Reports, Discoverer also.
*4.* Enable OracleAS Portal
*5.3.5 Step 5:* Configure the New Middle Tier (M2) to Run Your Existing Portal
*1.* Create both virtual hosts as done on M1
*2.* Copy dads.conf, oradav.conf, cache.conf, web.xml from M1 to M2
*3.* Re-register mod_osso on M2. To do this, perform the following steps by copying osso.conf from M1 to M2
*4.* Synchronize the DCM by using the following command
MID_TIER_ORACLE_HOME_M2/Apache/Apache/bin/ssotransfer MID_TIER_ORACLE_HOME_M2/Apache/Apache/conf/osso/osso.conf
*5.* Run dcmctl updateConfig
*6.* add the necessary mod_rewrite and mod_oc4j directives to the httpd.conf and mod_oc4j.conf files respectively
*7.* Restart Oracle HTTP Server on M2
*8.* Access the OracleAS Web Cache Manager on M1 and follow steps 9,10,11,12,13,14,15,16 for Webcache seetings and clustering.
Also will appreciate if can get some info on the following:
*1.*
When I configure the Webcache as per the Document but if I bring down one Midtier Instance the requests are not going to the other Instance that is up and ignores the case whether an instance is down. Any idea how what and where do I need to provide any setting which in case of instance is down routes the requests to the one that is up.
*2.*
What exactly happens when it says To enable monitoring of the LBR's front-end host and port settings for OracleAS Portal edit target.xml. Is this for LBR to find if an Instance is down or not and route the requests appropriately.
Thanks again for all the help.

How to configure multiple listeners to listen for the same instance.

Hello everyone,
I am running oracle database 11g and I want information regarding how to configure multiple listeners to listen for the same database instance. Actually I know how to configure more than one listener but the main thing that I am confused about is when we create listener.ora file, do we have to statically register the database instance with both the listeners or the instance will register itself with both the listeners.
According to my knowledge the instance will register with the listener specified by LOCAL_LISTENER parameter and we cannot have more than one value for this parameter.
Please only give detailed answers with example as I am tired of simple answers with details that I already know.

Hello,
Yes, it can make sense to have several listener for one Oracle instance. For instance you may have one listener for the applications another listener for DBA administration tasks as well as one listener dedicated to dataguard broker. It is not possible to have several listeners listening on the same IP and Port.
By default the database try to automatically register to a listener on port 1521. To instruct the instance to register to a specifc list of listeners you can add in the init.ora the local_listener parameter with an alias definition:
i.e
local_listener=MY_SET_OFF_LISTENERS
in your tnsname.ora add an entry called:
MY_SET_OFF_LISTENERS_LOCAL= (ADDRESS_LIST=
(ADRESS=(PROTOCOL=TCP)(HOST=myhostname)(PORT=1530))
(ADRESS=(PROTOCOL=TCP)(HOST=myhostname)(PORT=1531))
(ADRESS=(PROTOCOL=TCP)(HOST=myhostname)(PORT=1532))
In this sample your instance will register to three listeners listening on respectively port 1530, 1531 and 1532
If you want your clients can be balanced over the 3 listeners

How to configure multiple domains in Active directory

HI,
How can I configure multiple domains on Active Directory. When I installed AD it asked for a domain name, there I gave ravigupta.com as domain name. But now I find no way of creating another domain.
I am a java developer and my task is to write a programme which returns all the domains available in LDAP server.
To start with ,I tried to create few domains in LDAP server ( AD ) but stuck up ,as i found there could exist only one domain.
Please tell me how to configure multiple domains in LDAP server ( Active Directory).
I skiped DNS configuration while AD installation.
-ravi

I'm sorry, but you should be asking on a different forum. This has nothing to do with Java.

How to enable traffic between VPN clients in Windows Server 2012 R2?

Hello,
I installed Remote Access role with VPN.
IPv4 Router is enabled: http://snag.gy/UAMY2.jpg
VPN clients should use static ip pool: http://snag.gy/REjkB.jpg
One VPN user is configured to have static ip: http://snag.gy/TWwq0.jpg
VPN server uses Windows Authentication and Windows Accounting.
With this setup, VPN clients can connect to server, get ip addresses and can see server via server's vpn ip. Server can connect to VPN clients too (Using client's vpn ips). But VPN clients can't communicate with each other.
For example, VPN server has ip 192.168.99.5
VPN Client 1 - 192.168.99.6
VPN Client 2 - 192.168.99.7
I am able to ping 192.168.99.5 from both clients, and able to ping 192.168.99.6 and 192.168.99.7 from server via remote desktop. But I am not able to ping 192.168.99.7 from client 1 and 192.168.99.6 from client 2.
If I trace route from 192.168.99.6 to 192.168.99.7 - I can see that packets goes to server (192.168.99.5) and next hop - request timeout.
What else should I configure to allow network traffic between VPN clients?

Hi,
To better analyze this issue, would you please post the routing tables on the two VPN clients? You can run "route print" at the command prompt to get the routing table.
Best regards,
Susie
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Subscriber Support, contact [email protected]

How to configure multiple databases in single listener

Hi,
I want to configure upto 8 standby databases in a server. But I do not know how to configure multiple databases within the listener.
Also can I use the same port number for all the databases.
please give your suggestions.
thankyou
satyanag

Please check (http://download.oracle.com/docs/cd/B10501_01/network.920/a96580/toc.htm)
Jonathan Ferreira
http://oracle4dbas.blogspot.com

How to configura multiple ldap server to the sun access manager

Hi,
please help how to configure multiple ldap server to the sun access manager, for example access manager does't find the user in ldap1 then it should search in ldap2.
Thanks
Mouli

There�s no need for deleting the default amSDK based datastore because it�s needed for some default accounts.
You may try to create the datastore using the commandline (amadmin)
Have a look /etc/opt/SUNWam/config/xml/idRepoService.xml
You may also try to create amadmin account in the external ldap directory.
(Un)fortunately i�ve never tried to remove the default datastore.
-Bernhard

Mavericks VPN dropouts with native VPN client and Cisco IPSec

Since update to Maverics I am experiencing VPN dropouts with native VPN client and Cisco IPSec
I am connecting via a WIFI router to a remote VPN server
The conenction is good for a while but eventually it drops out.
I had Zero issues in mountain lion and only have issues since the update to 10.9
I had similar issues in teh past with an unrelaibel wifi router but i am using a Verizon Fios router and it has worked impecably until mavericks
My thoughts are:
1 -issue with mavericks ( maybe the app sleep funciton affecting eithe VPN or WIFI daemons)
2- Issue with cisco router compaitibility or timing with Cisco IPSEC
3- Issue with WIFI itself on mavericks - some sort of WIFI software bug
Any thousuggestions?

Since update to Maverics I am experiencing VPN dropouts with native VPN client and Cisco IPSec
I am connecting via a WIFI router to a remote VPN server
The conenction is good for a while but eventually it drops out.
I had Zero issues in mountain lion and only have issues since the update to 10.9
I had similar issues in teh past with an unrelaibel wifi router but i am using a Verizon Fios router and it has worked impecably until mavericks
My thoughts are:
1 -issue with mavericks ( maybe the app sleep funciton affecting eithe VPN or WIFI daemons)
2- Issue with cisco router compaitibility or timing with Cisco IPSEC
3- Issue with WIFI itself on mavericks - some sort of WIFI software bug
Any thousuggestions?

PPTP VPN - Clients inside Cisco877w - server at workplace

I am trying to connect to my workplace PPTP server from my home that has a Cisco 877w ADSL/Wireless router. I configured the majority of the setup via CLI and just started playing with CCP. I've used version 2.5 and 2.7 on a virtual Windows station that resides on my primary Linux box.
Background in trying things out. PPTP works fine without CCP firewall wizard having been run - with just a vanilla interfaces configured kind of setting.
I ran the CCP Advanced Firewall task, specified that I had PPTP clients on the LAN and went with it. The proposed changes included GRE and PPTP stuff, but being green in the IOS Firewall, I have no idea what I was looking at.
My configuration as it gave me is as follows:
version 12.4no service padservice timestamps debug datetime msecservice timestamps log datetime msecservice password-encryption!hostname HomeRouter!boot-start-markerboot-end-marker!logging message-counter syslogno logging bufferedenable secret 5 MyPass!no aaa new-modelclock timezone Chicago -6clock summer-time Chicago date Apr 6 2003 2:00 Oct 26 2003 2:00!crypto pki trustpoint TP-self-signed-904815991 enrollment selfsigned subject-name cn=IOS-Self-Signed-Certificate-904815991 revocation-check none rsakeypair TP-self-signed-904815991!!crypto pki certificate chain TP-self-signed-904815991 certificate self-signed 01 30820240 308201A9 A0030201 02020101 300D0609 2A864886 F70D0101 04050030 30312E30 2C060355 04031325 494F532D 53656C66 2D536967 6E65642D 43657274 69666963 6174652D 39303438 31353939 31301E17 0D313430 32313632 33323035 315A170D 32303031 30313030 30303030 5A303031 2E302C06 03550403 1325494F 532D5365 6C662D53 69676E65 642D4365 72746966 69636174 652D3930 34383135 39393130 819F300D 06092A86 4886F70D 01010105 0003818D 00308189 02818100 B192CA33 08917B1D 8237C7BB 00E38CA6 4BE8B394 4A3C9A40 F7087B15 F5C9D7CB 50F15F43 1084859D CB14F438 5352A1BC BF38C005 15FD518D 362D5769 EFB2528D 1DCF2239 1F2F66CD 5B67B1FF 40108483 740EEB0F D9098DCA 82616014 884E4630 96391ED4 A6B5575B E46BA5FB 2F4FFC32 A7855C59 86B2EBFA FAE485D3 56AF5D5B 02030100 01A36A30 68300F06 03551D13 0101FF04 05300301 01FF3015 0603551D 11040E30 0C820A48 6F6D6552 6F757465 72301F06 03551D23 04183016 8014F385 49957AD6 804D76D9 AD5DADF7 C1BAF9E6 12C6301D 0603551D 0E041604 14F38549 957AD680 4D76D9AD 5DADF7C1 BAF9E612 C6300D06 092A8648 86F70D01 01040500 03818100 387142CF 1B60955E D7D63134 E07E381F BF5491CD 571D718D A8B73E2E 327C81C8 35E33754 67662C59 0FDD3F8E 9B0F8B69 4BF95AD8 E8484EC6 C00A7BE2 5D168C98 818812AF B9490F55 C19257B4 8FE70B49 1D5F0772 5F0550E1 DE7C17DB 02DBA7DB 233AFF65 B381970E 3DEAFF79 482D2914 788665BF 0ED9117F 8ADB6844 2A1854E0            quitdot11 syslog!dot11 ssid Wireless1 vlan 1 authentication open authentication key-management wpa mbssid guest-mode wpa-psk ascii 7 097F46080E0B57310A1E1D6A0F3D24323B623006130F1858!dot11 ssid Wireless2 vlan 2 authentication open mbssid guest-mode!ip source-route!!ip dhcp excluded-address 10.0.0.1 10.0.0.99ip dhcp excluded-address 10.0.1.1 10.0.1.99!ip dhcp pool Local-Network   network 10.0.0.0 255.255.255.0   default-router 10.0.0.1    dns-server 8.8.8.8 8.8.4.4 !ip dhcp pool Guest-Network   network 10.0.1.0 255.255.255.0   dns-server 8.8.8.8 8.8.4.4    default-router 10.0.1.1 !!ip cefip name-server 8.8.8.8ip name-server 8.8.4.4ip name-server 4.2.2.2ip name-server 4.2.2.1ip ddns update method NO-IP HTTP add http://MyUser:[email protected]/nic/[email protected]/nic/update?hostname=<h>&myip=<a> interval maximum 1 0 0 0 interval minimum 0 0 5 0!no ipv6 cef!multilink bundle-name authenticated!vpdn enable!vpdn-group pppoe request-dialin protocol pppoe!!!username MyLocalUser privilege 15 password 7 01010101011010101! !!archive log config hidekeys!!no ip ftp passive!class-map type inspect match-all SDM_GRE match access-group name SDM_GREclass-map type inspect match-any CCP_PPTP match class-map SDM_GRE match protocol pptpclass-map type inspect match-any ccp-skinny-inspect match protocol skinnyclass-map type inspect match-any ccp-cls-insp-traffic match protocol pptp match protocol cuseeme match protocol dns match protocol ftp match protocol https match protocol icmp match protocol imap match protocol pop3 match protocol netshow match protocol shell match protocol realmedia match protocol rtsp match protocol smtp extended match protocol sql-net match protocol streamworks match protocol tftp match protocol vdolive match protocol tcp match protocol udpclass-map type inspect match-all ccp-insp-traffic match class-map ccp-cls-insp-trafficclass-map type inspect match-any ccp-h323nxg-inspect match protocol h323-nxgclass-map type inspect match-any ccp-cls-icmp-access match protocol icmp match protocol tcp match protocol udpclass-map type inspect match-any ccp-h225ras-inspect match protocol h225rasclass-map type inspect match-any ccp-h323annexe-inspect match protocol h323-annexeclass-map type inspect match-any ccp-h323-inspect match protocol h323class-map type inspect match-all ccp-invalid-src match access-group 100class-map type inspect match-all ccp-icmp-access match class-map ccp-cls-icmp-accessclass-map type inspect match-any ccp-sip-inspect match protocol sipclass-map type inspect match-all sdm-nat-ssh-1 match access-group 101 match protocol sshclass-map type inspect match-all ccp-protocol-http match protocol http!!policy-map type inspect ccp-permit-icmpreply class type inspect ccp-icmp-access inspect class class-default passpolicy-map type inspect sdm-pol-NATOutsideToInside-1 class type inspect sdm-nat-ssh-1 inspect class type inspect CCP_PPTP pass class class-default drop logpolicy-map type inspect ccp-inspect class type inspect ccp-invalid-src drop log class type inspect ccp-protocol-http inspect class type inspect ccp-insp-traffic inspect class type inspect ccp-sip-inspect inspect class type inspect ccp-h323-inspect inspect class type inspect ccp-h323annexe-inspect inspect class type inspect ccp-h225ras-inspect inspect class type inspect ccp-h323nxg-inspect inspect class type inspect ccp-skinny-inspect inspect class class-default droppolicy-map type inspect ccp-permit class class-default droppolicy-map QoS_Out_BVI2 class class-default   police rate 500000 !zone security in-zonezone security out-zonezone-pair security ccp-zp-self-out source self destination out-zone service-policy type inspect ccp-permit-icmpreplyzone-pair security ccp-zp-in-out source in-zone destination out-zone service-policy type inspect ccp-inspectzone-pair security ccp-zp-out-self source out-zone destination self service-policy type inspect ccp-permitzone-pair security sdm-zp-NATOutsideToInside-1 source out-zone destination in-zone service-policy type inspect sdm-pol-NATOutsideToInside-1!bridge irb!!interface ATM0 no ip address no ip redirects no ip unreachables no ip proxy-arp ip flow ingress no atm ilmi-keepalive!interface ATM0.1 point-to-point no ip redirects no ip unreachables no ip proxy-arp ip flow ingress pvc 8/35 pppoe-client dial-pool-number 1 !!interface FastEthernet0!interface FastEthernet1!interface FastEthernet2!interface FastEthernet3 switchport access vlan 2!interface Dot11Radio0 no ip address ! encryption vlan 1 mode ciphers aes-ccm ! ssid Wireless1 ! ssid Wireless2 ! mbssid speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0 station-role root world-mode dot11d country US outdoor no cdp enable!interface Dot11Radio0.1 encapsulation dot1Q 1 ip virtual-reassembly no cdp enable bridge-group 1 bridge-group 1 subscriber-loop-control bridge-group 1 spanning-disabled bridge-group 1 block-unknown-source no bridge-group 1 source-learning no bridge-group 1 unicast-flooding!interface Dot11Radio0.2 encapsulation dot1Q 2 native bridge-group 2 bridge-group 2 subscriber-loop-control bridge-group 2 spanning-disabled bridge-group 2 block-unknown-source no bridge-group 2 source-learning no bridge-group 2 unicast-flooding!interface Vlan1 no ip address ip virtual-reassembly bridge-group 1!interface Vlan2 no ip address bridge-group 2!interface Dialer0 description $FW_OUTSIDE$ ip ddns update hostname me.domain.com ip ddns update NO-IP ip address negotiated no ip redirects no ip unreachables no ip proxy-arp ip mtu 1492 ip nat outside ip virtual-reassembly zone-member security out-zone encapsulation ppp no ip route-cache cef no ip route-cache ip tcp adjust-mss 1452 dialer pool 1 dialer-group 1 no cdp enable ppp authentication pap callin ppp pap sent-username MyUsername password 7 MyPassword!interface BVI1 description $FW_INSIDE$ ip address 10.0.0.1 255.255.255.0 ip nat inside ip virtual-reassembly zone-member security in-zone!interface BVI2 description $FW_INSIDE$ ip address 10.0.1.1 255.255.255.0 ip nat inside ip virtual-reassembly zone-member security in-zone service-policy output QoS_Out_BVI2!ip forward-protocol ndip route 0.0.0.0 0.0.0.0 Dialer0ip http serverip http authentication localip http secure-server!!ip dns serverip nat inside source list 1 interface Dialer0 overloadip nat inside source static tcp 10.1.1.10 22 interface Dialer0 xxxxx!ip access-list extended SDM_GRE remark CCP_ACL Category=1 permit gre any any!no logging trapaccess-list 1 permit 10.0.0.0 0.0.0.255access-list 1 permit 10.0.1.0 0.0.0.255access-list 100 remark CCP_ACL Category=128access-list 100 permit ip host 255.255.255.255 anyaccess-list 100 permit ip 127.0.0.0 0.255.255.255 anyaccess-list 101 remark CCP_ACL Category=0access-list 101 permit ip any host 10.1.1.10!!!!!control-plane!bridge 1 protocol ieeebridge 1 route ipbridge 2 protocol ieeebridge 2 route ipbanner login ^CUnauthorized access is STRICTLY PROHIBITED! ^C!line con 0 exec-timeout 15 0 password 7 01010101010101010101 no modem enableline aux 0line vty 0 4 exec-timeout 5 0 privilege level 15 login local transport preferred none transport input ssh!scheduler max-task-time 5000ntp server 199.102.46.73end
Any clues as to what I would have to do to allow the PPTP connection to complete? It appears as though GRE may not be getting through? I haven't found much in the way of fixing this. My Google-fu might be lacking.

Remote VPN client is not showing any default gateway
PPP adapter VPN Connection:
   Connection-specific DNS Suffix . :
   Description . . . . . . . . . . . : VPN Connection
   Physical Address. . . . . . . . . :
   DHCP Enabled. . . . . . . . . . . : No
   Autoconfiguration Enabled . . . . : Yes
   IPv4 Address. . . . . . . . . . . : 192.168.1.100(Preferred)
   Subnet Mask . . . . . . . . . . . : 255.255.255.255
   Default Gateway . . . . . . . . . :
   DNS Servers . . . . . . . . . . . : 203.134.24.70
                                       203.134.26.70
   NetBIOS over Tcpip. . . . . . . . : Enabled

How do you keep your VPN clients up to date?

Hi, how do you keep your Cisco VPN clients up to date? Our users connect to a Cisco 3015 Concentrator. It needs to be as automatic as possible.
Thanks

Check this link,
http://www.cisco.com/en/US/docs/security/vpn_client/cisco_vpn_client/vpn_cli
ent46/administration/guide/vcAch3.html
Example:
Steps to perform an automatic update for VPN client :
===================================================
1. Download update-4.8.00.0440-major-K9 file on your PC from the link below and unzip it.
http://www.cisco.com/cgi-bin/tablebuild.pl/vpnclient-3des
It will have the following files::
- binary_config.ini
- sig.dat
- vpnclient-win-is-8.00.0440-k9.exe
- vpnclient-win-msi-8.00.0440-k9.exe
2. Create a webserver with a folder and move all the above files to this folder on webserver.
3. Now on your vpn client create a new profile. This profile file will appear in the profiles folder of the vpn client. Copy this file to your desktop and zip it. Name the
zipped file as profiles.zip. Delete the profile from the client.
4. Make a copy of your binary_config.ini on your desktop. Rename it to new_update_config.ini. This is just to make sure its not saved as a txt file.
Open the above file and write the following on it:
[Autoupdate]
Required=1
5. Now move the new_update_config.ini and profiles.zip to the webserver. Once we browse to the webserver it should look like --
http://webserver/~razshah/vpn_profile_update462/
Index of /~razshah/vpn_profile_update462
Name Last modified Size Description
Parent Directory 09-Mar-2005 13:24 -
binary_config.ini 09-Mar-2005 13:26 1k
new_update_config.ini 11-Mar-2005 11:35 1k
profiles.zip 09-Mar-2005 13:26 1k
sig.dat 09-Mar-2005 13:26 2k
vpnclient-win-is-4.6..> 09-Mar-2005 13:26 7.6M
vpnclient-win-msi-4...> 09-Mar-2005 13:26 10.3M
6. The concentrator is configured as follows:
Client Type is Windows
URL http://webserver/~razshah/vpn_profile_update462
Revisions 4.6
7. On your PC go to the VPN Client > updates folder. Delete the update_config file if its already there. This folder should have only autoinstall (this file will be added if update works) autoupdate header files.
The update does take about 5 mins. To see the new file we have to close and reopen the client. Once connected make sure you are able to browse to the webserver and see all the files.
1- Auto update runs only on Windows 2000 and Windows XP, all other client types update manually. Windows NT users get notified and can get an update manually from the update server.
2- Remote users must have the VPN Client for Windows 4.6 or greater installed on their PCs to use the automatic update feature.
Regards,
~JG

How to configure multiple IP-Adresses on one NIC in OVM

Hi guys,
we have some OVM Servers 2.2.1 installed. They all have three NICs in them (eth0-2). For eth0 and eth2 we need multiple IP-Adresses configured to work with our storage solution. The configuration should look like this:
eth0:0 - 192.168.31.x
eth0:1 - 192.168.33.x
eth1 - 192.168.0.x
eth2:0 - 192.168.32.x
eth2:1 - 192.168.34.x
I tried creating gonfig files ifcfg-eth0:0 in /etc/sysconfig/network-scripts with the following content
DEVICE=eth0:0
BOOTPROTO=static
ONBOOT=yes
NETMASK=255.255.255.0
IPADDR=192.168.31.3
TYPE=Ethernet
HWADDR=00:1b:21:06:f0:fa
But it does not work. Neither eth0:0 nore an additional xenbr is configured when i restart.
I can configure multiple ip addresses for xenbr0 by calling something like "ifconfig xenbr0 192.168.31.x". But these settings get lost as sonn as i reboot the server.
I have already searched google, forums and blogs for a solution but could not find one. I thought that this should be a pretty common task. In "normal" linux it is not an issue at all.
Has somebody any experience with a setup like this? I would really apreciate your help.
Thanks
Marek

Hi,
configuring IP aliasses seems to work the same way like configuring VLANs. You will have to configure the appropriate bridges at system startup manually.
E.g. this little script is what I use to configure VLANs and briges on my OVM:
#!/bin/bash
echo "Configuring VLANs and bridges\n"
echo "Configuring VLAN 24 on eth2"
vconfig add eth2 24
brctl addbr br2.24
brctl addif br2.24 eth2.24
ifconfig eth2.24 up
ifconfig br2.24 up
echo "Configuring VLAN 31 on eth2"
vconfig add eth2 31
brctl addbr br2.31
brctl addif br2.31 eth2.31
ifconfig eth2.31 up
ifconfig br2.31 up
This script is run at startup by init using this startup skript in /etc/init.d, which is what I think you're missing as you can already seem to bring up the needed IPs manually - you'd have to change the chkconfig accordingly, that is make sure that the config script gets startet after the network has been brought up, like this: # chkconfig: 2345 11 91
[root@oraclevm01 ~]# cat /etc/init.d/vlan-config
#! /bin/bash
# vlan-config configure VLANs
# chkconfig: 2345 11 89
# description: Configures VLANs at boot time before the \
# network is started.
### BEGIN INIT INFO
# Provides: $vlan
### END INIT INFO
# Source function library.
. /etc/init.d/functions
if [ ! -f /etc/vlan-config ]; then
exit 0
fi
# See how we were called.
case $1 in
     start)
               # configure vlans
               /etc/vlan-config
          echo $"Usage: $0 {start}"
          exit 1
esac
exit 0
Hth,
budy
Edited by: budachst on Jun 29, 2011 8:11 AM

How to configure multiple IP addresses on one NIC?

Hi,
I just installed a OVM Server in version 3.2.1 and the according VMManager. Now i wanted to try to configure the Server/Server Pool. Now i come across a problem, which was already a big problem in OVM 2 while configuring the Networks.
All our OVM Servers have three NICs in them. One is for VMs and Management, the others are for connection to our SAN (Dell PowerVault MD 3220i). My problem is, that due to the network setup, the two NICs for storage need two IP addresses in two different networks each. This shouldn't be a problem, because usually in linux all you have to do is configure something like eth1:1. I remember having huge trouble configuring it in our OVM 2 cluster up to the point where I had to write a shell script to configure the second IP.
Anyways, I have configured two of the storage networks on eth1 and eth2 of the VM Server. Now i cannot configure any more IP addresses, because eth1 and eth2 are not available anymore for configuration in a third network. I really hoped that it would be possible in OVM 3 to configure multiple IP addresses. And probably it is only my lack of knowledge of how to configure it.
So any advice is well appreciated.
Thanks!
Regards,
Marek Hubatka

You should be able to do this by using "VLAN Groups".
http://docs.oracle.com/cd/E35328_01/E35332/E35332.pdf
Check out the VLAN groups section. You must great the VLAN groups before you can assign them to interfaces.

How to Configure Multiple Purchase Requisitions per Service Order

Hi experts!
Sorry if this is in the wrong spot, but I was wondering how I can configure multiple Purchase Requisitions to be created from a service or maintenance order (IW31) based on the control key (or if it's even possible).
What would be the pros and cons of doing this? We currently only have one PR being created for one order (a 1-to-1 relationship), however now with implementing external services, we want 2 or more PRs created based on the control key. Is the control key the best way to go, or should I be looking at a different deciding field?
Thanks in advance!
Stephanie

Raj,
Thank you so much for the information. That does help! However business requirements are now changing to have different Purchase Requisitions created for a single order in the following scenarios:
             - New Purchase Req created for different operations (you explained how above, perfect!)
             - Seperate Purchase Req created for non-stock items (your answer above seems to group service operations and non-stock into the same Purchase Req).
             - New Purchase Req created if the order has already been released. (If the order's status is still at "Create", then the additional component can be appended to the existing Purchase Req. If the order's status is "Released", and a new component is added, a new Purchase Req is created).
As mentioned, you explained how to do the first requirement. Is there anyway SAP can handle the next two requirements using standard config and not customizing anything?
Thanks in advance!
Steph

How to configure multiple dev environment in single IP

HI,
I have a WLS running on a Windows NT machine. I want to configure multiple partition/environment
in that single WLS so that each user will have their own partition/environment to
play around. Once they are happy with their EJBs then we shall move them to a testing
environment. Is that possible in WLS??. Can anyone please guide me to a good documentation
about this one.
Many Thanks
Vasan.
PS: I dont want a clustering technology all i want is that in a single ip i wanna
multiple development environment.

Tom,
looks like you are specifying http protocol in
sky.framework.ejb.SkySessionBean.getInitialContext method.
Change it to t3 or, if the JNDI lookup is in the same JVM, don't specify
PROVIDER_URL. If you have to use http tunneling due to any reason , you have to
enable HTTP Tunneling in server to which initial context is created. It is
disabled by default in 60. You can do so via console. Please refer to
documentation , let me know if you need additional help.
Viresh Garg
Principal Developer Relations Engineer
BEA Systems
Tom Purcell wrote:
Kevin,
You said that with 6.0 the following happens:
On the second server I get an error when I do
http://host:secondServerPort/index.html
Is this the error you get on the Admin Server:
<Feb 28, 2001 12:42:24 PM EST> <Info> <HTTPTunneling> <Login rejected with
code: 'Failed', reas
on: You are trying to use http tunneling
The server will not let you connect'>
<Feb 28, 2001 12:42:24 PM EST> <Error> <HTTP> <Problem dispatching servlet
request
weblogic.common.T3Exception: You are trying to use http tunneling
The server will not let you connect
at weblogic.socket.TunnelLogin.rejectConnection(TunnelLogin.java:87)
at weblogic.socket.TunnelLogin.service(TunnelLogin.java:59)
at
weblogic.servlet.internal.MuxableSocketHTTP.dispatch(MuxableSocketHTTP.java:
467)
at
weblogic.socket.NTSocketMuxer.processSockets(NTSocketMuxer.java:638)
at
weblogic.socket.SocketReaderRequest.execute(SocketReaderRequest.java:23)
at weblogic.kernel.ExecuteThread.execute(ExecuteThread.java:137)
at weblogic.kernel.ExecuteThread.run(ExecuteThread.java:120)
>
And on the Managed Server:
<Feb 28, 2001 12:42:24 PM EST> <Error> <ConnectionManager> <Could not
connect to: '0S:127.0.0.1
:[-1,7001,-1,-1,-1,-1,-1]'
java.net.ProtocolException: Tunneling result unspecified - is the HTTP
server at host: 'localho
st' and port: '7001' a WebLogic Server?
at
weblogic.rjvm.http.HTTPClientJVMConnection.handleNullResponse(HTTPClientJVMC
onnectio
n.java:152)
at
weblogic.rjvm.http.HTTPClientJVMConnection.connect(HTTPClientJVMConnection.j
ava:194)
at
weblogic.rjvm.http.HTTPClientJVMConnection.createConnection(HTTPClientJVMCon
nection.
java:98)
at weblogic.rjvm.Protocol.createConnection(Protocol.java:207)
at
weblogic.rjvm.ConnectionManager.findOrCreateConnection(ConnectionManager.jav
a:997)
at
weblogic.rjvm.ConnectionManager.bootstrap(ConnectionManager.java:364)
at
weblogic.rjvm.ConnectionManager.bootstrap(ConnectionManager.java:330)
at
weblogic.rjvm.RJVMManager.findOrCreateRemoteInternal(RJVMManager.java:228)
at weblogic.rjvm.RJVMManager.findOrCreate(RJVMManager.java:188)
at
weblogic.rjvm.RJVMFinder.findOrCreateRemoteServer(RJVMFinder.java:180)
at weblogic.rjvm.RJVMFinder.findOrCreate(RJVMFinder.java:149)
at weblogic.rjvm.ServerURL.findOrCreateRJVM(ServerURL.java:207)
at
weblogic.jndi.WLInitialContextFactoryDelegate.getInitialContext(WLInitialCon
textFact
oryDelegate.java:232)
at
weblogic.jndi.WLInitialContextFactoryDelegate.getInitialContext(WLInitialCon
textFact
oryDelegate.java:174)
at
weblogic.jndi.WLInitialContextFactory.getInitialContext(WLInitialContextFact
ory.java
:123)
at
javax.naming.spi.NamingManager.getInitialContext(NamingManager.java:668)
at
javax.naming.InitialContext.getDefaultInitCtx(InitialContext.java:246)
at javax.naming.InitialContext.init(InitialContext.java:222)
at javax.naming.InitialContext.<init>(InitialContext.java:198)
at
sky.framework.ejb.SkySessionBean.getInitialContext(SkySessionBean.java:112)
at
sky.framework.ejb.SkySessionBean.setSessionContext(SkySessionBean.java:94)
at
sky.ejb.session.skyreferencesession.SkyReferenceSessionBeanImpl.setSessionCo
ntext(Sk
yReferenceSessionBeanImpl.java:87)
at
weblogic.ejb20.internal.StatelessEJBHome.createBean(StatelessEJBHome.java:22
9)
at
weblogic.ejb20.pool.StatelessSessionPool.createBean(StatelessSessionPool.jav
a:90)
at
weblogic.ejb20.pool.StatelessSessionPool.getBean(StatelessSessionPool.java:7
5)
at
weblogic.ejb20.manager.StatelessManager.preInvoke(StatelessManager.java:67)
at
weblogic.ejb20.internal.BaseEJBObject.preInvoke(BaseEJBObject.java:113)
at
weblogic.ejb20.internal.StatelessEJBObject.preInvoke(StatelessEJBObject.java
:55)
at
sky.ejb.session.skyreferencesession.SkyReferenceSessionBeanEOImpl.setDataSou
rce(SkyR
eferenceSessionBeanEOImpl.java:22)
at
sky.ejb.session.skyreferencesession.SkyReferenceSessionBeanEOImpl_WLSkel.inv
oke(SkyR
eferenceSessionBeanEOImpl_WLSkel.java:161)
at
weblogic.rmi.internal.BasicServerAdapter.invoke(BasicServerAdapter.java:373)
at
weblogic.rmi.cluster.ReplicaAwareServerRef.invoke(ReplicaAwareServerRef.java
:128)
at
weblogic.rmi.internal.BasicServerAdapter.invoke(BasicServerAdapter.java:237)
at
weblogic.rmi.internal.BasicRequestHandler.handleRequest(BasicRequestHandler.
java:103
at
weblogic.rmi.internal.BasicExecuteRequest.execute(BasicExecuteRequest.java:1
7)
at weblogic.kernel.ExecuteThread.execute(ExecuteThread.java:137)
at weblogic.kernel.ExecuteThread.run(ExecuteThread.java:120)
>
Thanks,
Tom
<Feb 28, 2001 12:42:24 PM EST> <Info> <ConnectionManager> <Bootstrap unable
to get a: 'Protocol
: 'http'' connection to: 'localhost/127.0.0.1' on port: '7001'>
"Kevin Apte" <[email protected]> wrote in message
news:[email protected]...
This advice applies to WL5.1. I have been trying to configure a
multiinstance Weblogic with no success. I want multiple copies
of the sample petStore available for test by multiple users.
I think in 6.0
You would need to open an admin server
Open the configuration file for say PetStore.
Clone the petStore- call it petStore2. .
Create a copy of the startup script and modify it to start PetStore2.
After doing this only one config.xml is created for both servers.
I am able to start the first server and view the petStore application,
On the second server I get an error when I do
http://host:secondServerPort/index.html
How does one create multiple instances in WL6.0 using the console
or using a XML editor ?
Jesse E Tilly <[email protected]> wrote:
[This followup was posted to weblogic.developer.interest.management
and
a copy was sent to the cited author.]
In article <[email protected]>, [email protected]
says...
HI,
I have a WLS running on a Windows NT machine. I wantto configure multiple partition/environment
in that single WLS so that each user will have theirown partition/environment to
play around. Once they are happy with their EJBs thenwe shall move them to a testing
environment. Is that possible in WLS??. Can anyoneplease guide me to a good documentation
about this one.
Many Thanks
Vasan.
PS: I dont want a clustering technology all i wantis that in a single ip i wanna
multiple development environment.
NT isn't a multiuser environment. I will assume that
you mean some
Win32 box sitting in a room where people can copy their
classes/EJBs and
test their stuff. If this is the case, the setup is easy.
Create a directory and startup script for every developer.
Have a
global properties file in the same directory as the scripts
so that
common settings are, well, common. Tell each user to
modify the various
parts of the properties files in their directories to
deploy EJBs and
register servlets, etc etc.
In each startup script, you will have to specify the server
directory
and the binding port for each person. Pick a port (something
easy to
remember and high, like 30000, 30001, etc etc) for each
person. Why?
Well, when they connect to the app server, they'll know
they're hitting
only their server. Also, TCP/IP won't let more than one
JVM bind to the
same port, so if you want simultaneous instances (> 4
you better have
one kick ass Win32 box) you have to do this.
Hope this solves your problem.
JT
Senior Developer, HotelTools INC
[email protected]

How to configure multiple smtp servers per domain

Hi,
how do we configure multiple smtp servers per domain/corporate in iplanet messaging server 5.2. i wanted to do this so that i can configure some domains with virus scanning and some domains without antivirus.

Hi Martin,
Well we are trying to run a report without exactly specifying the name of reports server anywhere, e.g. in database or in form or anywhere else. Now if I do not supply a reports server name using RUN_REPORT_OBJECT, the error it displays is FRM-41211: Integration Error : SSL failure ... However if I specify the reports server name in the form, the reports run perfect. Also the name of reports server is specified in rwservlet.properties.
Now the question goes as follows:
Can I run my report from Form without specifying the name of the Reports server anywhere at all. This is so because either an in-process reports server should be picked or the one which is entered in rwservlet.properties should be pickec up by default. Please correct us if we are wrong. once we are through with it, we have to move to Oracle 10gR2 concept of reports server.
Thanks in anticipation,
Ruchi/Saurabh

How to configure Multiple PPTP VPN Clients on cisco 3g supported Router

Similar Messages

Maybe you are looking for