How to create extend network through existing wifi router-Belkin N150

Dear sir,
I like to inform you that customer are using belkin N150 wifi router in his room( For wifi) but he want to extend his network with the help of airport express through existing network (wifi).Is it possible to extend network by the airport express?Please give the suggestion or step to configure the airport express through existing WIFI network.
I am waiting for your reply as earliest.
Thanks,
Dipankar Das

.Is it possible to extend network by the airport express?
Yes, if the AirPort Expess will connect to the Belkin router using a permanent wired Ethernet cable connection.
No, if you want the AirPort Express to connect to the Belkin router using wireless.
If you want to extend using wireless, then use another Belkin product, which will be compatible with your Belkin router.

Similar Messages

  • How to create a partition on existing table?

    Hey
    Could some one please tell me on how to create a partition on existing table?

    Could some one please tell me on how to create a partition on existing table?
    You can't - that isn't possible. Unless a table is already partitioned you can NOT create another partition on it.
    You must either redefine the table as a partitioned table (using the DBMS_REDEFINITION package) or create a new partitioned table and move the data to its new partitions.
    The choice will depend on how much data the existing table has and whether you can do it offline.

  • How to create a cluster on existing table

    how to create a cluster on existing table

    user8949393 wrote:
    how to create a cluster on existing tableAFAIK you can't. You have to create the cluster from scratch, something like
    --cluster key can be just one column also
    CREATE CLUSTER s_emp_dept_ic (deptno NUMBER(7), dname varchar2(30));
    CREATE TABLE emp(
      DEPTNO NUMBER(7),
      DNAME  VARCHAR2(30),
      EMPNO  NUMBER(4),
      ENAME  VARCHAR2(30)
    --cluster clause puts table in cluster.  Deptno, dname are table columns in
    --cluster key
    CLUSTER s_emp_dept_ic (deptno,dname);
    --a cluster index must be created before any data is inserted
    --the index columns used come from the cluster key from CREATE CLUSTER
    CREATE INDEX s_emp_idx ON CLUSTER s_emp_dept_ic;

  • Trying to connect a NetGear Wifi Range Extender to my existing Wifi. I have an Airport Extreme Base Station and I am also connected to a Vonage Phone Router. Any help would be appreciated?

    I am trying to connect a NetGear Wifi Range Extender to my existing Wifi. I have an Airport Extreme Base Station and I am also connected to a Vonage Phone Router. Any help would be appreciated?
    The Apple update Firmware for my Airport Extreme Base Station does not update for some reason? Help?
    Additionally, I have an older version Airport Express that does not update with the newer Airport Utility Version 6.3 and asks me to download 5.6 to update? Is this worth it?
    Thanks

    The netgear is not going to work very well.. and not at all unless it is universal wireless extender.. you cannot use WDS method.
    If it does support universal wireless then make sure the airport uses a rational SMB compatible wireless name.. not an apple name which is 35 characters long with spaces and illegal characters like apostrophe.
    So nice AE name.. AEwifi and actually while you are trying.. fruitlessly to do this.. use AE24ghz and AE5ghz (so different names on the different bands)
    Assuming your AE is gen3 or greater.
    You should also fix the wireless channel at least for 2.4ghz since the netgear is probably only going to repeat 2.4ghz so use channel 11, as a trial.
    And use no wireless security as a test.. if that works.. then use WPA1 & 2.. as often old equipment using WPA2 is not compatible.
    If it fails with simple name.. fixed channel and no security. Sorry it is not compatible at all.. it happens.
    If your AE is G wireless or earlier model.. really the time has come for replacement.
    If your Express is G wireless model it is not supported.. and is too old to bother with expect I guess if you want to run audio to a speaker.
    You must use older 5.6 utility to do this.. so do you have a computer running older OS.. up to Mountain Lion it is easy to install with a bit of manipulation.. later is much harder .. or windows computer anywhere or available to you.

  • How to create a server through WLST  ( Weblogic Scripting Tool ) ?

    How to create a server through WLST ( Weblogic Scripting Tool ) ?
    Thanks in advance...
    Sanjay

    Hi Murugesh,
    Thanks a lot for you reply..
    I was able to create a server using create(). Is it possible to clone a server ?
    When i create a server following tags is added to config.xml
    <server>
    <name>testServer_lab1</name>
    <listen-port>43000</listen-port>
    </server>
    And if i do a clone through admin console, following is added to config.xml
    <server>
    <name>testServer2_lab1</name>
    <machine xsi:nil="true"></machine>
    <listen-port>7001</listen-port>
    <cluster xsi:nil="true"></cluster>
    <listen-address></listen-address>
    <graceful-shutdown-timeout>120</graceful-shutdown-timeout>
    </server>
    If incase, cloning is not possible through WLST, can i add following
    <machine xsi:nil="true"></machine>
    <listen-port>7001</listen-port>
    <cluster xsi:nil="true"></cluster>
    <listen-address></listen-address>
    <graceful-shutdown-timeout>120</graceful-shutdown-timeout>
    under <server> tag which is created through WLST ?
    I am using 9.2 version.
    Regards
    Sanjay

  • I'm not able to connect to internet through my wifi router, which is Sitecom 150N working fine with pc

    I'm not able with ipod touch to connect to internet through my wifi router, which is Sitecom 150N working fine with pc

    Your router may not have given your iPod a valid IP address when the iPod requested it. To check on this go to Settings > Wifi > your network name and touch the ">" to the right to see the network details. If the IP address shown starts with 169 or is blank then your router didn't provide an IP address and you won't be able to access the Internet.
    Sometimes the fix for this can be as simple as restarting your router (remove power for 30 seconds and restart). Next, reset network settings on your iPod (Settings > General > Reset > Reset network settings) and then attempt to connect. In other cases it might be necessary to update the router's firmware with the latest from the manufacturer's support web pages.
    If you need more help please give more details on your network, i.e., your router model and version (the 150n designation is not a unique model), the wifi security being used (WEP, WPA, WPA2), is MAC address filtering being used, etc.

  • How to Turn your iPad into a WiFi router for your laptop?

    how to Turn my iPad into a WiFi router for your laptop?

    Chris CA wrote:
    iPads have no tethering abilities either.
    I know, but I still don't know what the OP was asking.

  • On Ipod touch connected to wifi router Belkin App Store does not work

    I have a wifi router Belkin.
    My Ipod touch connects to it, and Safari works properly.
    When I try to use App Store, screen shows "loading" (I have Italian settings and original message is "carico") and never connects....
    I suspect there are wrong settings in mi wifi router, but I do not what to correct
    Conection to other wifi router is ok, just my Belin at hoome is wrong......
    Thanks

    Can't connect to the iTunes Store
    Best Fixes for ‘Cannot Connect to iTunes Store’ Errors | iPad Insight

  • How to create extended range network using three apple airport extremes?

    Hello! The idea is, I want to use Apple routers to create a large range network for a hotel that has 300 FT Hallway. I have tried everything in the airport utility but nothing works.  The idea is, in the whole 300 FT hallway, i want to put three apple airport extreams. one in the middle of the hallway which will be connected to the modem, one on the each end of the hallway that will be connected to the middle airport extreme via eithernet or extend network range option from airport utility.
    Image shows, what I am trying to achieve.
    http://imageshack.us/scaled/landing/35/10e6.jpg
    These what I have tried so far. Airport extreme is refered here as "airport"
    1. Connect Airport 1 to modem, then on Airport 2 use extend network feature to extend the range of airport 1 network. This did not work. Airport 2 keeps on blinking yellow.
    2. Did same thing as step 1 but also tried it using ethernet cable going from Airport 1 in to Airport 2's ethernet inbound port.
    3. Connected modem to switch, from swith one ethernet cable goes in to Airport 1 and one cable from SWITCH goes in to the airport 2's ethernet port.
    Only thing that works is, if I connect ONLY ONE airport to the modem or the switch. I am not able to use two airport extremes together.
    Please advise what I can do using these or other apple products to have extended wifi coverage in the entire hallway.
    I, however do need to use three extremes as one is not enough to cover the area.
    Thank you.
    Hopefully some one can help me and correct me where I am doing something wrong.
    Thanks.

    Exactly what model extreme are you using??
    What device is being used as setup with airport utility?
    1. Connect Airport 1 to modem, then on Airport 2 use extend network feature to extend the range of airport 1 network. This did not work. Airport 2 keeps on blinking yellow.
    Amber blinking just means something needs adjusting.. it should still show up in the utility and you can find out what the extreme is complaining about. If not start over.. it is absolutely crucial you factory reset and start over.. the extreme must present as a new wireless device in wifi and then you can setup to extend the existing wireless.
    2. Did same thing as step 1 but also tried it using ethernet cable going from Airport 1 in to Airport 2's ethernet inbound port.
    This is a much better arrangement.. The Extreme plugged into the Modem.. what mode is it in? It must create a wireless network.. make sure the network name is short.. no spaces and pure alphanumeric.
    The extreme plugged into to give better range.. must be in bridge mode.
    It must create a wireless network of the exact same name.. exact same security settings and same password.
    Follow the instructions here if you do not follow.
    http://support.apple.com/kb/HT4260
    3. Connected modem to switch, from swith one ethernet cable goes in to Airport 1 and one cable from SWITCH goes in to the airport 2's ethernet port.
    This is the same configuration as 2. There is no difference where you put the switch.
    Only thing that works is, if I connect ONLY ONE airport to the modem or the switch. I am not able to use two airport extremes together.
    Setup according to the apple instructions for roaming network.. it will work.
    If it fails give us more info.. what model AE. etc.
    Also give us the IP address and screenshot of each units setup for wireless.

  • How to create Document Structure for existing project in Solution Manager

    Hi gurus
    We have all the project document saved using Solution manager . we have ended with Phase1.
    We are starting Phase2 and they are asking me to creat different folder as Phase to in existing project and store all the Documents
    Can any one please tell me how to create New folder and store the documents in Existing project
    Point will given for helpfull Answer
    Thanks
    Bhaskar

    Hi Bhaskar,
    Assuming you have full authorisations, the procedure is simple.
    Please go SOLAR_PROJECT_ADMIN transaction.
    From the menu please select Project -> Copy
    In the ensuing screen, key in your desired project name, scroll through the other checkboxes to see if you are happy with the default choices; if not, take corrective actions.
    In the last set of radi buttons "Desired behaviour at later version comparison", the default choice (2nd entry there - Adjust target project to the original of the source project) is fine.
    From your scenario, since you do not have a Template -> Implementation Project functionality and instead are copying from one Implementation to the other, this radio button is of little consequence.
    Execute the process.
    In the window that comes up, please choose Local Object, assuming that you do not want to capture the whole contents into a 'Transport'. This is more required if you are aiming to copy the project from one SolMan instance to another.
    It would give an information message "Generating in batch job (Name ......)
    In a few minutes, you'd receive an intimation of the Project being copied.
    That's pretty much about it. Have a check on the newly created project in SOLAR01.
    Please let me know if you have any doubts.
    Best regards,
    Srini

  • How to create material bom through CS01 if bom created by using ppe

    Hi experts,
    I have created a material bom through PPE of material A. Now i want to create bom through CS01for same material A.
    system shows error "A breakdown (PVS/VA) already exists in iPPE for material".
    So how can create bom through CS01?
    Suggest me.
    Regards,
    Nitin Nerkar

    Hi,
    Please check and implement the below note,
    [1311089|https://websmp130.sap-ag.de/sap(bD1lbiZjPTAwMQ==)/bc/bsp/spn/sapnotes/index2.htm?numm=1311089]
    Thanks
    Hrishi

  • How do I set up Express box as addition to existing WIFI router?

    Used to be able to do this when setting up the Express box, as I did years ago at home. But there's no option in the install process to enable this - which renders the product pretty useless.
    Any ideas?
    Cheers
    Neil

    Hi Bob
    thanks for getting responding to my request.
    When I originally set up Airport express network at home, the set up software gave a couple of options, to either be a stand alone wifi node, or be added to existing router - not necessariy an Apple one - I have a Netgear router at home. This was a decade or so ago.
    We recently bought Airport Express box for the office as we want to stream music to it and the set uo software has changed in that it insists the Airport Express box is connected to a router with a cable - which defeats the point of a WIFI product.
    So - my question was how to do this as it is insane that a wifi box cannot connect via wifi to a wifi router.
    However we found a solution by using the Apple Remote app to set up the Airport Express box so that it has been added to the Netgear router we have in the office.
    So - it turns out you can connect an Apple Airport express box wirelessly to a non Apple wireless router, but not with Apple Airport assistant utility - you have to use Remote on an iPhone.
    This isn't how I'd configure the products, but hey, what do I know?
    Cheers
    N

  • How to create Data account  on iPad2 WiFI+CDMA in India

    I bought a new iPad2 32 GB(CDMA+WiFi) from US. I registered it with apple and my device is up and running.
    And I see that it selects the carrier (vodafone) and the same is listed in the settings and on top left corner of the iPad. But when i try to browse,i get a dailog box, "Could not activate cellular data network, you are not subscribed to a cellular data services", when i try to create data account, it asks me about firstname, lastname and telepone number. How to get telephone number?  How to create a data account for cdma iPad2 in India, i don't want use international roaming on it.
    My WiFi connection is ON and its working fine.
    Let me know, how to activate internet on my device using cellular data in India.
    Thanks in advance.
    Regards,
    -Prem

    You can't unless there is a provider that uses CDMA netwok at the same frequencies as Verizon in India. There is no GSM sim slot on the CDMA  iPad 2. The newer iPads all have a GSM sim slot for use worldwide.

  • How to create reports from my existing web application on Java/J2EE with Oracle Client 10g as the backend?? Help sought for

    Our company has developed an  Web Application and we are also looking out for the development of reports using Business Objects Exterprise XI Release 2 and for this purporse I do require some help from the forum who can literally show me how to get on and working on creating the reports.

    Thats why I thought I should make the following chain in the keystore, possibly in this order.
    1. My private key (simply generated in the server)
    2. Import Root certificates from NS
    3. Import Trusted certificate issued by NS
    Then when I sign with my private key surely an association will be formed to the trusted authority certificate. The problem I'm having is when I first made my private key I used openSSL as it was only intended for HTTPS. Now I need to create a keystore so I can use jarsigner to sign the jar file, and I can't see how to create a keystore using my existing private key. Surely if I created a new key and self sign, then import the trusted certificate the association will fail, as the private key will not be the same 1 that I used to make the CSR when applying for the trusted certificate.

  • How to create a user through a webpage which I build.

    Hi, every one,
    I only have HTML DB developer privilege. How to create a new user and assign a password through a webpage which I build. This means that how can I create a HTML DB user using code. which table in HTML DB stores user's info. Can I access that table by insert user info.
    Appreciate!!

    Scott,
    thanks for explanation.
    But I don't understand one thing. If security group ID associated with workspace, what does it mean this code (and associated functionality in admin pages):
    -- G R O U P S
    prompt Creating Groups...
    begin
    wwv_flow_fnd_user_api.create_user_group (
    p_id => 873904557635271,
    p_GROUP_NAME => 'ADMINS',
    p_SECURITY_GROUP_ID => 504313619757457,
    p_GROUP_DESC => 'Àäìèíèñòðàòîðû ñèñòåìû. Ñîçäàþò íîâûõ ïîëüçîâàòåëåé, ìîäèôèöèðóþò ïàðîëè èòï.');
    end;
    begin
    wwv_flow_fnd_user_api.create_user_group (
    p_id => 872621957621347,
    p_GROUP_NAME => 'MANAGERS',
    p_SECURITY_GROUP_ID => 504313619757457,
    p_GROUP_DESC => '...');
    end;
    begin
    wwv_flow_fnd_user_api.create_user_group (
    p_id => 872900617624637,
    p_GROUP_NAME => 'OFFICERS',
    p_SECURITY_GROUP_ID => 504313619757457,
    p_GROUP_DESC => '...');
    end;
    begin
    wwv_flow_fnd_user_api.create_user_group (
    p_id => 873414815628792,
    p_GROUP_NAME => 'USERS',
    p_SECURITY_GROUP_ID => 504313619757457,
    p_GROUP_DESC => ...');
    end;
    and how I can use this groups (not security, as I understand) for application controlling access?

Maybe you are looking for