How to get 2 lans ports working on K8N Neo2 platinum

I can only get the one lan port working which is the realtek device. Ive tried installing drivers for the marvel lan but it doesnt show up in device manager. Can any one tell me how i get this second lan port working.

Quote from: Justmeto on 02-July-06, 05:02:54
I can only get the one lan port working which is the realtek device. Ive tried installing drivers for the marvel lan but it doesnt show up in device manager. Can any one tell me how i get this second lan port working.
The other network interface is by nVidia -- the Marvel part is just the PHY for the nForce3 NI -- and the drivers should install with the nVidia driver install. Which nVidia driver package are you using? People have had NI trouble with the 5.11 pack - personally I use the 5.10 pack with the 4.79 IDE/SATA drivers which you should be able to find here: [urlhttp://downloads.guru3d.com/download.php?id=19[/url]. In BIOS Setup under Integrated Peripherals, what's labeled MAC Lan(nVIDIA) is the one you want to make sure is on Auto.

Similar Messages

Which SATA port on the K8N Neo2 Platinum?

Hi! I recently got a 160GB Maxtor DiamondMax 9 Plus hard drive, but I have read somewhere (i forgot where I read it) that two S-ATA ports on the K8N Neo2 Platinum will corrupt your hard drive data if you overclock. I dont know if this is still true (I have BIOS ver 1.8) but please could someone tell me which port I should connect my S-ATA drive to? (the only drive I have at the moment is a 160GB IDE drive). I dont want RAID. Thanks!

Quote from: Supershanks on 14-June-05, 18:46:14
If u go over 230 sata 1/2 are liable to corruption.
230GB i assume?

Can't get IDE drive to work with K8N NEO2

I built my computer two months ago. The only hard drive I installed was a Samsung 160GB SATA. The Windows XP installation was flawless and the system has worked perfectly ever since.
This past week I decided to install my old Western Digital IDE hard drive. I connected it to PATA port 1 on the motherboard. It's jumpered as a Primary device and connected to the primary port on the IDE cable.
The problem is that when I boot the computer with the IDE drive connected it will hang on the gray Platinum screen for around 5 minutes. If I hit DEL and enter BIOS after 5 minutes I can see that the drive is detected and the boot order already was set for the SATA drive first and the IDE drive second. Then if I reboot it hangs on the Platinum screen again for five minutes. When it finally clears that I get messages indicating that no boot device is available. If I shut down, disconnect the IDE drive, and reboot with only the SATA drive connected it boots flawlessly.
I checked my device manager and see that the nvidia nforce3 250 Parallel ATA controller and Serial ATA controller drivers are installed.
Is there anything else I can check or do to get the computer to boot with an IDE drive connected?
Thanks!

WD drives are special compared to others .
If they are alone on the ide channel they shall not be jumpered as master .
This is only when it is sharing the channel with another ide/atapi device .
Instead the jumper shall be removed , they call it single drive jumpering (SD).
And the reason why bios get hung is :
It finds a master jumpered drive , and since it does it will try to detect the slave
but there isn't one .

How should I setup a SATA HDD on K8N Neo2 Platinum?

I bought a 200Gb SATA hard disk (Maxtor 6V200E0). This is the first time I work with SATA HDDs.
I plugged the HDD as I always did with an IDE HDD, and installed Windows XP -I have configured nothing-. The problem I'm experiencing is that sometimes Windows XP boots fine, and sometimes it doesn't. After the POST, the Windows Logo does never appear. I do not see anything.
Reading the Manual, I believe to understand that no matter if you only have one SATA HDD, I should setup nVRAID in the BIOS. Is that correct?. If I configure the nVRAID in the BIOS and setup RAID 0, should this problem disappear?. How should I setup my SATA HDD?. Is it the same to connect it to SATA1/SATA2/SATA3/SATA4 controller?. Or should it be connected into SATA1 -just because there's only 1 HDD in the system-?.
Thanks a lot!

Yes, unfortunatelly there's a major issue with this kind of HDDs and nForce3&4 chipset based mainboards. I found the following article at the Maxtor web-site -I asked them to send me the firmware upgrade; standing by-:
Question
I have heard or read that Maxtor drives are incompatible with nForce3 or nForce4 chipsets, or that I need a firmware update to make a Maxtor drive compatible with the nForce chipset. Is this true?
Answer
Note: This solution is only to be applied to the listed products and only when used with the nVidia© nForce3© or nForce4© chipsets. If you are unsure as to which chipset you have, please contact your motherboard manufacturer or visit your motherboard manufacturer's website for clarification.
Firmware updates are not upgrades. They offer no performance enhancements and exist only to provide specific compatibility resolutions. If you have a drive that is working properly in a computer, you do not need a firmware update.
Do not use a firmware update that is not authorized directly by Maxtor as there are variations of firmware for different revisions of drives that can render drives inoperable if applied to the wrong drive.
Applying firmware to a drive that is not authorized by Maxtor will void the warranty on the drive as this would be considered an unauthorized modification. Please see Maxtor's Limited Warranty Statement for more information.
If your drive came inside an OEM machine such as a Dell, Apple, Gateway etc., do not apply a firmware update at all as this will void the warranty which is held by that manufacturer. Please contact your OEM vendor directly.
The following issues have been identified with Maxtor SATA II drives and the nVidia nForce4 controller:
Data Corruption: If you are experiencing data corruption issues, the problem is not with the hard drive firmware. Please visit nVidia's website to update to the latest nVidia chipset drivers to resolve this issue. Make sure to be familiar with your motherboard specifications as there are several variations.
NCQ: If you are experiencing problems with NCQ (Native Command Queueing) please see nVidia's Knowledgebase ID 768 for more information with an issue nVidia is having with NCQ and the nForce4 chipset, and a forthcoming resolution. They also offer a solution to temporarily disable NCQ.
No Detection: If you are experiencing a problem with your Maxtor SATA-II drive not being detected by your nForce3 or nForce4 host controllers at bootup:
Note: This does not apply if your drive is connected to a non-nForce3 or nForce4 controller such as SIIG (Silicon Image), HighPoint, Promise etc. Many motherboards have multiple host controllers onboard so make sure you are familiar with your motherboard specifications and schematics.
The drives affected are those listed in the following table:
Model begins with:
Code (Firmware revision)
6B- or 7B-
BANC1980
BANC1B70
BANC1BM0
BANC1BY0
BANC1E00
6L- or 7L-
BANC1G00
BANC1G10
BANC1G20
6H- or 7H-
HA431BW0
6V- or 7V-
VA111610
VA101610
VA131610
VA141610
Example of a drive label:
Image
To check your current firmware revision on the drive without removing it from the system, use the Powermax diagnostic CD. Drive model, Serial and firmware Revision is displayed in the upper right hand corner after selecting the drive to test.
A firmware update to resolve this issue for Maxtor SATA II drives is available by contacting Maxtor Support. Please have the drive serial number and the Code number available, which will be listed on the top label of the drive itself.
Firmware updates will be issued for those drives experiencing this problem only, not for experimental troubleshooting. Due to the nature of a firmware code update, a drive can be potentially rendered inoperable so it is critical that data is backed up first.

Harddrive LED wont work on K8N Neo2 Platinum???

Hey guys, my system seems to be runnning perfectly fine except that all my led's seem to work except my harddrive
Now my board already came with v1.4 so i know i have the latest bios update. so any ideas on why its not working? and oh yeah, if i put the cable on backwards the light STAYS on!!!

Quote from: fafner on 18-February-05, 11:52:46
Reverse the LED jumpers on the MB. The polarity has to be correct for the LED to work.
Ok well how do i do that? i tired putting the cable on the opposite way that its suppost to go on and the light just stays on....

Update to kichat: FAQ 2 - How to get my router to work with iChat?

kichat: FAQ 2 - How to get my router to work with iChat? December 2008 version 3
(Note to Hosts. to be removed on acceptance. Please use this to replace http://discussions.apple.com/thread.jspa?threadID=121775 )
Getting your router started with iChat.
Appropriate for using iChatAV 2 upwards. Edits have been made for iChat 4
Glossary for this FAQ
Routers: Any configurable device that sits between your computer and the internet link you have. This includes Modems that Route as well as "routers"
Routers seem to fall into two categories
Those that work straight from the box. See Apple Article HT1787
NOTE :This Article has not been updated in content since Jan 04 Only being changed to an Article from the Previous Doc listing
Even then some list that they need tweaks.
and those that do not.
This post will deal with what you may need to look at.
First off make sure your device is acting as a DHCP server. (if you are already on the internet you may not have to bother with this.)
Check in the Tiger System Preferences > Network Preference Pane, in the "Built in Ethernet" option from the "Show" drop down list.
In Leopard the Networks are listed on the left with icons. The Airport Option will need you to access the Advance Button for the Next bit.
Make sure the TCP/IP tab is the 'front' one. You should be able to see Configure IPv4 and it most likely reads Using DCHP. Make a note of your IP address. It will start 10.xxx.xxx.xxx or 192.168.xxx.xxx (the 'x' s will stand for any number between 1 and 255). The range 172.16.xxx.xxx is also a possible value at this point. Rarely used, but it is part of the RFC for Address Allocation for Private Internets.
Your router is most likely to be configurable from your browser. You will need to find the IP address to type into the browser from any Readme or PDF files that came on the install disk or visit the makers website and download a manual.
The Port Forward.com site lists many devices and clicking on one will take you to a list of Applications. This iChat will open an page that will start by telling you the defaults to access the device
Opening or Allowing ports. Several Methods not all devices have all of them.
DMZ (Demilitarised Zone)
This is a less secure setting that basically opens all ports and points the incoming data to your computer. (not helpful if you have more than one computer on your LAN). It can be considered as an extreme form of Port Forwarding
Port Forwarding (also Virtual Server or Pin Holes)
These settings are usually found in an Advanced setting.
You may need to set an incoming IP address (Usually 0.0.0.0 to any outside server), a port that data will arrive on, the Inside computer's IP address (your computer) and the port it will deal with the data on and the protocol it will use.
See this pic for an example of the description above.
In this example shows that on some Port AND Protocols need to be listed.
iChat uses TCP and UDP so some devices will need the ports listed one by one and some settings done twice, once for each protocol. The example above has a "Both" setting
See Apple Article HT1507 Previously Doc 93208 for more information. This is the Tiger iChat 3 list. The same ports are needed for Leopard except for these changes
My Note 2:
On the first link Note 1 under tables in that link would be better if it read:
" 1. All iChat AV traffic is UDP -
except for ports 5190 and 5298, which need to be open for both TCP as well;
and 5220, 5222, which need to be open for TCP only. "
Note 2
GoggleTalk needs port 5223 on TCP. Also note the Server name for iChat 3 set ups
UPnP Universal Plug n Play.
This is a simple Plug and Play type of setting. iChat can find it's own way through a router if the device has this capability.
By Not doing Port Forwarding, Triggering or DMZ and enabling UPnP the application is allowed to control the modem and the ports that are open.
They close after the application has finished with them on a timed basis.
On some devices the number of "hops" (how far away the UPnP can be "seen") can be reduced from a default of 4)
Trigger Ports
Some devices offer a security measure that works by a first or trigger port receiving a data packet and then opening further ports when accepted.
The first port for incoming Video or Audio invites is port 5678.
Pre iChat 4
When you click on the invite window the process moves in to port 5060 (so these will need to be opened by the trigger port) for negotiating the final group of ports from the group of 20 (16384-16403 These will need to open when the trigger says so as well). Therefore port 5678 triggers ports 5678, 5060, 16384-16403. All on UDP. Port 5190 neeeds to trigger port 5190 for both TCP and UDP.
See this variation where only the ports listed above are completed.
The other single ports need to be set one by one in addition. (5220,5222, 5223 5297, 5298, 5353)Replace
iChat 4
The port used in IChat 4 is port 16402 instead of port 5060. The group of 20 ports is reduced to 10 (16393-16402). This is because all the In and Out Audio and Video data is on one port. Other that than the settings are the same.
At this time there is no Info on the ports the Screen Sharing in iChat 4 uses.
Wireless
Here you will have to read around but this Apple Article TA25949 Previously Doc 58514 might be a good starting place.
Essentially whether you are wireless or Ethernet to your routing device makes very little difference to the way you do things.
Your computer will get two IPs from a DHCP server if you are connected by both methods. (iChat does not like this)
Multiple devices
Make sure only one is acting as a DHCP server. Make sure wireless devices are bridged properly.
Further Help
I have found that this site (ADSLGuide) to be helpful.
It is British based but I have linked you to the Apple Related Discussions Forum.
Eliminating Problems on my Personal web pages.
The ports and their function within iChat. (my personal Web pages again)
This is not a step by step approach. You will have to read around the information about your device.
Collected FAQs and Expansions: Index Page Based on FAQs here by EZ Jim and myself
Also http://www.portforward.com/routers.htm for instructions with Pics on Port Forwarding and access info as mentioned earlier.
Click on your device.
Select iChat on the next page.
Follow the info on the next.
This site is godd for finding out the Default IP to use in a web browser and the default User ID and Passwords needed to do so.
Gives you a chance to look at at pics to give clues to where some of these other things are.
With thanks to Macmuse for comment on the Original (Aug 23rd 2004)
and to EZ Jim for his work on iSights on my web pages.
I may receive some form of compensation, financial or otherwise, from my recommendation or link.
9:51 PM Saturday; December 6, 2008

kichat: FAQ 2 - How to get my router to work with iChat? December 2008 version 3
(Note to Hosts. to be removed on acceptance. Please use this to replace http://discussions.apple.com/thread.jspa?threadID=121775 )
Getting your router started with iChat.
Appropriate for using iChatAV 2 upwards. Edits have been made for iChat 4
Glossary for this FAQ
Routers: Any configurable device that sits between your computer and the internet link you have. This includes Modems that Route as well as "routers"
Routers seem to fall into two categories
Those that work straight from the box. See Apple Article HT1787
NOTE :This Article has not been updated in content since Jan 04 Only being changed to an Article from the Previous Doc listing
Even then some list that they need tweaks.
and those that do not.
This post will deal with what you may need to look at.
First off make sure your device is acting as a DHCP server. (if you are already on the internet you may not have to bother with this.)
Check in the Tiger System Preferences > Network Preference Pane, in the "Built in Ethernet" option from the "Show" drop down list.
In Leopard the Networks are listed on the left with icons. The Airport Option will need you to access the Advance Button for the Next bit.
Make sure the TCP/IP tab is the 'front' one. You should be able to see Configure IPv4 and it most likely reads Using DCHP. Make a note of your IP address. It will start 10.xxx.xxx.xxx or 192.168.xxx.xxx (the 'x' s will stand for any number between 1 and 255). The range 172.16.xxx.xxx is also a possible value at this point. Rarely used, but it is part of the RFC for Address Allocation for Private Internets.
Your router is most likely to be configurable from your browser. You will need to find the IP address to type into the browser from any Readme or PDF files that came on the install disk or visit the makers website and download a manual.
The Port Forward.com site lists many devices and clicking on one will take you to a list of Applications. This iChat will open an page that will start by telling you the defaults to access the device
Opening or Allowing ports. Several Methods not all devices have all of them.
DMZ (Demilitarised Zone)
This is a less secure setting that basically opens all ports and points the incoming data to your computer. (not helpful if you have more than one computer on your LAN). It can be considered as an extreme form of Port Forwarding
Port Forwarding (also Virtual Server or Pin Holes)
These settings are usually found in an Advanced setting.
You may need to set an incoming IP address (Usually 0.0.0.0 to any outside server), a port that data will arrive on, the Inside computer's IP address (your computer) and the port it will deal with the data on and the protocol it will use.
See this pic for an example of the description above.
In this example shows that on some Port AND Protocols need to be listed.
iChat uses TCP and UDP so some devices will need the ports listed one by one and some settings done twice, once for each protocol. The example above has a "Both" setting
See Apple Article HT1507 Previously Doc 93208 for more information. This is the Tiger iChat 3 list. The same ports are needed for Leopard except for these changes
My Note 2:
On the first link Note 1 under tables in that link would be better if it read:
" 1. All iChat AV traffic is UDP -
except for ports 5190 and 5298, which need to be open for both TCP as well;
and 5220, 5222, which need to be open for TCP only. "
Note 2
GoggleTalk needs port 5223 on TCP. Also note the Server name for iChat 3 set ups
UPnP Universal Plug n Play.
This is a simple Plug and Play type of setting. iChat can find it's own way through a router if the device has this capability.
By Not doing Port Forwarding, Triggering or DMZ and enabling UPnP the application is allowed to control the modem and the ports that are open.
They close after the application has finished with them on a timed basis.
On some devices the number of "hops" (how far away the UPnP can be "seen") can be reduced from a default of 4)
Trigger Ports
Some devices offer a security measure that works by a first or trigger port receiving a data packet and then opening further ports when accepted.
The first port for incoming Video or Audio invites is port 5678.
Pre iChat 4
When you click on the invite window the process moves in to port 5060 (so these will need to be opened by the trigger port) for negotiating the final group of ports from the group of 20 (16384-16403 These will need to open when the trigger says so as well). Therefore port 5678 triggers ports 5678, 5060, 16384-16403. All on UDP. Port 5190 neeeds to trigger port 5190 for both TCP and UDP.
See this variation where only the ports listed above are completed.
The other single ports need to be set one by one in addition. (5220,5222, 5223 5297, 5298, 5353)Replace
iChat 4
The port used in IChat 4 is port 16402 instead of port 5060. The group of 20 ports is reduced to 10 (16393-16402). This is because all the In and Out Audio and Video data is on one port. Other that than the settings are the same.
At this time there is no Info on the ports the Screen Sharing in iChat 4 uses.
Wireless
Here you will have to read around but this Apple Article TA25949 Previously Doc 58514 might be a good starting place.
Essentially whether you are wireless or Ethernet to your routing device makes very little difference to the way you do things.
Your computer will get two IPs from a DHCP server if you are connected by both methods. (iChat does not like this)
Multiple devices
Make sure only one is acting as a DHCP server. Make sure wireless devices are bridged properly.
Further Help
I have found that this site (ADSLGuide) to be helpful.
It is British based but I have linked you to the Apple Related Discussions Forum.
Eliminating Problems on my Personal web pages.
The ports and their function within iChat. (my personal Web pages again)
This is not a step by step approach. You will have to read around the information about your device.
Collected FAQs and Expansions: Index Page Based on FAQs here by EZ Jim and myself
Also http://www.portforward.com/routers.htm for instructions with Pics on Port Forwarding and access info as mentioned earlier.
Click on your device.
Select iChat on the next page.
Follow the info on the next.
This site is godd for finding out the Default IP to use in a web browser and the default User ID and Passwords needed to do so.
Gives you a chance to look at at pics to give clues to where some of these other things are.
With thanks to Macmuse for comment on the Original (Aug 23rd 2004)
and to EZ Jim for his work on iSights on my web pages.
I may receive some form of compensation, financial or otherwise, from my recommendation or link.
9:51 PM Saturday; December 6, 2008

How to get online apps to work with the Verizon DSL modem firewall set at "Medium" level, not "Low?"

How to get online apps to work with the Verizon DSL modem firewall set at “Medium” level? Xbox 360 Live, FTP, and the Windows sntp Time checker native to Windows XP WON’T WORK unless the Verizon firewall is first reset down to “Low.” Then all works well, but I then risk low firewall protection. Setup: · Westell 6100 DSL modem (Software Version: VER:4.04.03.00 Transceiver Revision: 7.2.3.0 Model Name: C90-610015-06), · D-Link DIR-655 wireless router (Hardware Version: A3, Firmware Version: 1.21), For Xbox 360 Live the “canned” port forwarding rule for provided in Verizon’s drop-down list for the Westell 6100 modem forwards ports 88 and 3074 for both TCP and UDP. This does not meet Microsoft’s forwarding recommendations for Xbox 360 Live stated at http://support.microsoft.com/kb/908874. Instead, for the Verizon modem (Westell) I made a new port forwarding rule to comply with those Microsoft instructions. It forwards ports 53, 80 and 3074 for TCP and ports 53, 88 and 3074 for UDP. These same ports are also forwarded in the D-Link router configuration. For FTP, port 21 is also forwarded for TCP and UDP in both modem and router. But they don’t work until I first cripple the Verizon firewall down to “Low.” How to get them to work with the Verizon firewall up to Medium?

While I do not know the answer to your question, BUT since you have this modem and another router - you could just follow.
http://www.dslreports.com/faq/13600
^^
If you are the original poster (OP) and your issue is solved, please remember to click the "Solution?" button so that others can more easily find it. If anyone has been helpful to you, please show your appreciation by clicking the "Kudos" button.

I have an airbook, 10.7.4 LION, thunderbolt ethernet adapter and when trying to install 1.2.1 thunderbolt upgrade it says "this software not supported on this system"? Any advice on how to get the adapter to work?

I have a new airbook, 10.7.4 LION, thunderbolt ethernet adapter and when trying to install 1.2.1 thunderbolt upgrade it says "this software not supported on this system"? Any advice on how to get the adapter to work?

Welcome to Apple Support Communities
If you purchased the computer before 2010, your computer hasn't got Thunderbolt, so you can't use it

How to get the webcam to work?

Hi,
As I don't have an instruction book for this computer, can anyone tell me how to get the webcam to work please?
There is supposed to be something that pops up from the side of the screen, but I've left the mouse sit there for ages on all sides and nothing. Please assist me.
Kit_e

I refer you back to my original question.
There used to be a bar at the side that popped up when you left the mouse sit there for a bit. It no longer pops up ... ie: it's disappeared and will not return ... this is what "started" the webcam for use as a webcam.
I have no idea on how to use the webcam from any other place. There is no icon. There is no mention of it in the programs list. There is nothing. There is a webcam sitting there in the laptops lid, but I can't find where to "access it". Like I said there is no icon, nothing in the programs list.
I want to be able to use it. You know, like you use a webcam. On the web, as a camera. No particular website or software that I have in mind.
Thanks.

How to get this script to work with different browser

Do you guys know how to get this script to work with mozilla firefox?
do shell script "open -a safari 'https://login.binck.nl/klanten/Login.aspx?ReturnUrl=%2fklanten%2fdefault.aspx'"
tell application "Safari"
activate
          tell document 1
                    repeat until ((do JavaScript "location.host") is "login.binck.nl")
                              delay 1
                    end repeat
do JavaScript"document.getElementById('ctl00_Content_Gebruikersnaam').value='sim';document.ge tElementById('ctl00_Content_Wachtwoord').value='password';window.open(document. g etElementById('ctl00_Content_LoginButton').href, '_self', 'true');"
          end tell
end tell
Thank you so much in advance:)

That isn't possible. Firefox's AppleScript dictionary doesn't contain anything which can be used to manage JavaScripts.
(63741)

Hi. I have Snap To Grid and By Kind enabled in Lion but it's not working. When I trash an icon, instead of snapping the remaining icons to the By Kind grid, a space is left where the trashed icon was. Any suggestions on how to get Snap To Grid working?

Hi. I have Snap To Grid and By Kind enabled in Lion but it's not working. When I trash an icon, instead of snapping the remaining icons to the By Kind grid, a space is left where the trashed icon was. Any suggestions on how to get Snap To Grid working?

Where are you talking about the Desktop?
I don't see where it is possible to set both Snap to Grid and By Kind they seem to be mutually exclusive.
And then
If I have Snap to grid set I get the behavior you describe. If I have By Kind set the icons stay together and close up the space from the deleted icon.
regards

Any suggestions for how to get my logic keyboard working properly for FCE?

Any suggestions how to get my logic keyboard working properly for FCE? I can't use some of the shortcuts - insert, overwrite etc. maybe the system settings aren't correct?

This normally happens when debris builds between the trackball and the rollers on the inside of the mouse.
Turn the mouse upside down and rub the trackball vigorously on a sheet of paper or microfiber cloth to try and free it up.
Regards,
Captfred

How to get my Addon to work with the license key?

Hi,
Can someone tell me how to get the Addon to work with the license key?
I've follow the steps as stated in this thread:
[Re: SBO 2005 A - How do I get a Connection string from SAP B1.|Re: SBO 2005 A - How do I get a Connection string from SAP B1.]
1) i've registered a BASIS key and get a 'BASISXXXXXX" string
2) then i paste my BASIS key in "Solution" of Add-On Indentifier Generator and generate the Add-On Indentifier Code
3) then i paste the string to my source code
which is the "XXX" of the sample code in that thread.
static string AddonIdentifierString="XXX";
int lRetCode=0;
int errCode=0;
string errMsg= string.Empty;
string connectionStr ="";
link = new SAPbouiCOM.SboGuiApiClass();
connectionStr =Environment.GetCommandLineArgs().GetValue(1).ToString();
link.AddonIdentifier=AddonIdentifierString;
link.Connect(connectionStr);
oApp = link.GetApplication(-1);
vCompany = new SAPbobsCOM.CompanyClass();
string cookie = vCompany.GetContextCookie();
string conStr = oApp.Company.GetConnectionContext(cookie);
vCompany.SetSboLoginContext(conStr);
lRetCode = vCompany.Connect();
4) then i add my add-on using manager role at Add-on admin
5) then i can see my add-on there. it not suppose to be there since i've not installed any of my add-on license for my own add-on.
what steps did i miss? Can someone please advise? Thanks
ps : i'm coding in VB

Hi,
i think you have to change the license file attributing the number of licensing for your addon, then download it from https://websmp202.sap-ag.de/smb and then install it on SAP License manager, then I think you should give the license for your addon for individual users (example manager)
I hope it helps.
Best regards

Can I connect a device to get added LAN ports for my Airport Extreme?

Can I connect an added device to my styetem to get added LAN ports for my Airport Extreme Router system?
Mark Edwards

Connect a Gigabit Ethernet switch to any of the 3 Ethenret ports on the AirPort Extreme to add as many ports as you need.
Switches come in 5-port, 8-port, 16-port, etc versions.
Your local computer/electronics superstore will have what you need.

When using an airport extreme to extend a wireless modern, will the lan ports work?

When using an airport extreme to extend a wireless modern, will the lAN ports work?

The AirPort Extreme can extend the wireless signal from another Apple wireless router. When it does, the Ethernet ports on the extending AirPort router are enabled.
Apple's "extend" feature appears to be a proprietary Apple function, so it would be extremely unlikely that an AirPort Extreme...or any other Apple router....could extend a 3rd party router product wirelessly....if that is really what you are asking here.

How to get 2 lans ports working on K8N Neo2 platinum

Similar Messages

Maybe you are looking for