How to reset Current Employee No Range

Dear all,
We have created two wrong entries in SAP HR.
now we have deleted the data against employee codes, but how can we set the current no range to previous no
i will explain with example:
we created employee 90101 and 90102 due to some reasons we need to delete these employees
and assign Employee code 90101 to new applicant.
Please Help.
Thanks & regards,
Gaurav Sood

Hi,
After you completely delete the number using PU00,You can place the number you want in the number range status field. The system will pick this number when a new hire is performed.
- Suresh

Similar Messages

How to "move" current entry in number range status for trans. req.

For our project we plan an test system(a copy of productive sytem). We do not expect any transport request from productive system).
There we will have some changes(transport requests) in workbench(less) and customizing(most of all) (e.g. Let say the request nr will be REP9000001 REP9000007).
We will release them prior to next copy of productive system copy and reimport them just after system copy.
However next transport on test system I assume will start again with REP9000001 and not REP9000008. Do you know how to move current entry in number range. I checked the usual table nriv but did not find suitable entry
Thank you in advance

Hello,
i think there is no Solution because you must inittialize
your Transportsystem after a hom. Systemcopy. There are
many Steps to do to get a useable System. There is only a
Problem if don't do that work. One of it is Transaction
se06 that changes your Sourcesystem.
Regards
Stefan

For sweden the employee number range is completed Eg:23000000 to 239999999 now how to generate next employee id

For sweden the employee number range is completed Eg:23000000 to 239999999 now how to generate next employee id

Hi Bharathi,
If required no ranges are not there which you want to add then will not be problem and you can extend the 23999999 to your next limit like 39999999 check the overlapping.
Check extended no rage are present in the system and then system would not except because of overlapping.
Check and tell.
Regards,
Sankarsan

How to reset password if i forgot my current password

how to reset password if i forgot my current password

If the user account is associated with an Apple ID, and you know the Apple ID password, then maybe the Apple ID can be used to reset your user account password. In OS X 10.10 and later, this option also works with FileVault, but only if you enabled it when you activated FileVault. It's not retroactive. Otherwise, see below.
Note: If you've activated FileVault, this procedure doesn't apply. Follow instead these instructions.
Start up in Recovery mode. When the OS X Utilities window appears, select
Utilities ▹ Terminal
from the menu bar at the top of the screen—not from any of the items in the OS X Utilities window.
In the window that opens, type this:
resetp
Press the tab key. The partial command you typed will automatically be completed to this:
resetpassword
Press return. A Reset Password window opens. Close the Terminal window to get it out of the way.
Select the startup volume ("Macintosh HD," unless you gave it a different name) if not already selected. You won't be able to do this if FileVault is active.
Select your username from the menu labeled Select the user account if not already selected.
Follow the prompts to reset the password. It's safest to choose a password that includes only the characters a-z, A-Z, and 0-9.
Select
 ▹ Restart
from the menu bar.
You should now be able to log in with the new password, but the Keychain will be reset (empty.) If you've forgotten the Keychain password (which is ordinarily the same as the login password), there's no way to recover it.

Hi there, I'm Medel and I'm currently on Saudi Arabia. I forgot my security questions' answers and need to reset it but I just added an alternate email a while ago. Can anyone help me how to reset it even if I don't have a recovery email registered?

Can anyone help me how to reset my security questions on my apple account? I forgot the answers and need to reset it. Please Help...

An alternate email is not used for resetting security questions, do you know if you have a rescue email address on your account ? If you do then follow steps 1 to 5 half-way down this page and you should get a reset link on your account : http://support.apple.com/kb/HT5312
If you don't have a rescue email address (you won't be able to add one until you can answer your questions) then you will need to contact Support in Saudi Arabia to get the questions reset.
Contacting Apple about account security : http://support.apple.com/kb/HT5699#S
When they've been reset (and if you don't already have a rescue email address) you can then use the steps half-way down the HT5312 link above to add a rescue email address for potential future use

PA40-Employee Number Range sequence

Hi,
i was making an Entry in PA40,direct hiring and just opened the first screen where empcode is auto generated
and no details could be entered and were not even saved and 2 empocodes were missed i.e 98580 and 98581
But now when i am trying to re enter that same employee code system gives error message of Number range
how can i go back to the same Empcode Number which was auto generated,now the Interval range is showing the next empcode i.e. 98582
pls help

Dear All,
Problem has been resolved.
In PA04, I simply made the Current employee series as External and remove the Current value and saved
after manually entry in PA40 saved those mmissed employee code
again made the series as Internal and saved.
Ragards,
puja

I want to run down how dissatisfied I currently am with Verizon Wireless

I want to run down how dissatisfied I currently am with Verizon Wireless; this stated with the pre-order of the iPhones on Friday I like many other customers received the "ecdp" error on the web site and it took 45 minutes to actually be able to place the order. I got the order in and had a 09/19/2014 ship date; spoke with a few Customer Service Reps in various areas such as 611, on many of the 800 numbers available, Internet Orders (including a Supervisor) and even a Social Media Service Rep all who have confirmed this ship date to be accurate.
Well today (09/17/2014) I check the Pre-Order Status page and my date has been changed to 10/14/2014 so I call in to speak to Internet Orders and the Rep advises me that yes my date was pushed back but no reason is supplied, I asked to speak to a Supervisor and was transferred to Howard, Operator # 2431235, who stated that yes the prior rep was accurate and that there was no reason available as to why my ship date changed. Howard continues by stating that as per upper management, Apple reported to Verizon that no iPhone 6+'s would be available at launch for Verizon to ship and that this has been common knowledge, within the company, that the 6+'s were not shipping until 10/14/2014, and that prior Verizon employee's to include supervisors were misinforming me of my shipping date. Howard continued to state that the reason I got the "ecdp" error was because of the company that I work for as Verizon offers a discount so the 'ecdp" error is not something Verizon is currently addressing. Howard then tells me not to worry that with the 10/14 date is a guaranteed delivery date and not to worry, if the phones come in early the order will be filled, I at this point ask Howard to note my account with our conversation to include the fact that he stated the 10/14 was a guaranteed date, at this point he states that while he is telling me this he will not put it in writing as at that point Verizon would be obligated to meet that date at minimum and he was not willing to put his position on the line if the phone is not shipped by that date(this can be confirmed by reviewing the recording of the call as I was advised that I was on a recorded line). I then asked to speak to his supervisor and was told his supervisor went home for the day and that he was the highest level supervisor on at this time. When I then asked for his supervisors contact information to lodge a complaint he said that I would need to call back in on 611 from my handset as Customer Service handles complaints not supervisors.
I did call back and speak with a Representative on 611 who tried to assist but was not able to do much, this rep took my information and is having their supervisor call me to try addressing the way Howard handled the call however this has not occurred at the time of this writing. I did tell this rep that I was honestly considering going to another carrier, (I have been with Verizon 7-8 years and currently have 10 lines of service on my account) I know I will not get the iPhone 6+ on launch day with another carrier which was not the driving factor but rather the way Howard dealt with the situation and the lack of respect that as a customer of Verizon I have always got from other representatives, as you know it takes one person to sour someone on a whole company, Howard even stated that if I want to go to another carrier that was fine with him. However, the Customer Service Rep I spoke with after Howard (I wish I could remember his name) calmed me down not to leave Verizon but did agree that a complaint needed to be filed, personally I would like to file it directly with an Associate Vice President or higher but do understand that there is a “Chain of Command” that needs to be filed
Let this be a warning to anyone who call internet sale and gets Howard, operator #2431235, I would suggest you immediately request a different supervisor that will treat you with respect. As stated above Howard will tell you that the iPhone 6+ was not and has never been available to ship on launch day due to Apple purposely not providing enough units to meet the demand and that Verizon knew this while taking our pre-orders.

I feel your pain Robert. I do believe VZW and Apple knew all along the I6 Plus would not be available on 19 Sep and that it was a way to bolster new contracts, renewed contracts and apple sales stats. It's unfortunate the company wasn't more clairvoyant, most of us would have still pre-ordered but been a little less frustrated.

How to Reset HP LaserJet 1500L Drum and Toner

(Note: This also applies to some other laser printers too. If so then please update this thread to indicate the model and any extra instructions.)
The legacy 1500 and 1500L use dumb toner and drum cartages. They have a chip which simply counts the number of pages printed, and when a preset number (as per cartridge size) have been printed, it sends a signal to the printer to replace it. This is ok if you print the average amount of ink per page, but if you print a lot of photos, the cartage will be exhausted before the indicator flashes, and if like the rest of us you print the usual selection of documents etc, then probably about 50 to 25 percent of the toner remains - what a waste!.
Fortunately, (or not) HP kindly provide incorrect instructions how to reset the counter. It's a pity that customer support don’t read their own documentation, or put it in the manual.
Do exactly the following:
1) Turn the printer power switch off.
    Wait 10 seconds for any residual charges to clear.
2) While powered off, press and hold the GO button (right hand)
3) Turn the printer power switch on while continuing to hold the GO button down.
4) After the Go, Ready, and Attention LEDs turn on, continue holding the GO button
    for at least 20 seconds (maybe 30 seconds). During this time, the Attention,
    Ready, and Go LEDs will each eventually turn off.
5) When it seems to have stopped, now release the GO button.
6) The printers LEDs will begin cycling from front to back. After about 15-30 seconds it finishes
    and everything goes quiet. The printer should now be in the 'ready' state.
7) (The missing instruction) Press the cancel (orange) button.
Send a simple colour document to the printer and it should print out ok, proving it is all ok.
Keep printing until one of the cartages or the fixer toner drum are depleted and printing result is unacceptable.

Hailun, welcome to the forum.
Here is a guide to help you solve your problem. Read it carefully and follow the instructions step by step.
Please click "KUDOS" if I have helped you and click "Accept as Solution" if your problem is solved.
Signature:
HP TouchPad - 1.2 GHz; 1 GB memory; 32 GB storage; WebOS/CyanogenMod 11(Kit Kat)
HP 10 Plus; Android-Kit Kat; 1.0 GHz Allwinner A31 ARM Cortex A7 Quad Core Processor ; 2GB RAM Memory Long: 2 GB DDR3L SDRAM (1600MHz); 16GB disable eMMC 16GB v4.51
HP Omen; i7-4710QH; 8 GB memory; 256 GB San Disk SSD; Win 8.1
HP Photosmart 7520 AIO
++++++++++++++++++
**Click the Thumbs Up+ to say 'Thanks' and the 'Accept as Solution' if I have solved your problem.**
Intelligence is God given; Wisdom is the sum of our mistakes!
I am not an HP employee.

How to reset windows 2008 R2 Local Administrator password

Hi Team,
I have forget windows 2008 R2 local admin password, the server is not in domain , is it any way to reset local administrator password.
Regards,
Triyambak
Regards, Triyambak

When your Windows Server 2008 R2 computer is still accessible, you can reset or change your administrator password with ease by the following steps.
Step 1: Log in your Windows Server 2008 R2 computer through the administrator account.
Step 2: Click on “Start” on the lower left corner of your screen, and hit “Control Panel”, and then doubt-click on "User Account".
Step 3: Choose “Make changes to your user account”, and then click on “Change your password”.
Step 4: Now you will be asked to enter your current password, type in it.
Step 5: Enter your new password and retype it to confirm your new password. You are optional to type in a word or phrase as the hint of the new password. It is highly recommended.
Another tip, Using a password recovery tool to recover WIndows server 2008 administrator password
This is a universal WIndows password recovery method which can fix any Windows system password issue.
1. Get Windows Password Rescuer and install it on another computer.
2. Burn password reset disk into USB or CD/DVD device with Windows password recovery.
3. Boot Windows server from password reset USB or CD disk
4. Reset forgotten Windows server 2008 local or domain admin password without data loss.
Detailed steps: http://www.wimware.com/how-to/reset-windows-server-2008-password.html
I also have seen a way that users can use a Windows server 2008 install CD to reset the administrator password, you could search and have a try.

How to reset composite statitics from Enterprise Manager

Hi,
Someone knows how to reset statitics from a composite with their components, services and references from EM 11g without redeploy the composite?
Thank You in advance.
JP

John,
Yes your assumption is correct. Also, I have uninstalled (and removed user data) and re-installed DM. Also rebooted PC but still no luck. Eveytime I connect my new device to DM it pops up a msg: "Your messaging account is currently configured to use <old device>. Would you like to switch to <new device> instead?". I then proceed to click on "Yes", it still shows Active Device as the old one and Device Connected as new one.

Some one please tell me how to reset version 10.6.8 i just bought off cl

some one please tell me how to reset version 10.6.8 on macbook air i just bought off craiglist and forgot to ask if password on there

Clean Install of Snow Leopard
     1. Boot the computer using the Snow Leopard Installer Disc. Insert the disc into the
         optical drive and restart the computer. After the chime press and hold down the
         "C" key. Release the key when you see a small spinning gear appear below the
         dark gray Apple logo.
     2. After the installer loads select your language and click on the Continue
         button. When the menu bar appears select Disk Utility from the Utilities menu.
         After DU loads select the hard drive entry from the left side list (mfgr.'s ID and drive
         size.) Click on the Partition tab in the DU main window. Set the number of
         partitions to one (1) from the Partitions drop down menu, set the format type to Mac
         OS Extended (Journaled, if supported), then click on the Partition button.
     3. When the formatting has completed quit DU and return to the installer. Proceed
         with the OS X installation and follow the directions included with the installer.
     4. When the installation has completed your computer will Restart into the Setup
         Assistant. After you finish Setup Assistant will complete the installation after which
         you will be running a fresh install of OS X. You can now begin the update process
         by opening Software Update and installing all recommended updates to bring your
         installation current. Start by downloading and installing Mac OS X 10.6.8 Update Combo v1.1.

How to scale current output?

Hello everyone!
I have a pressure transducer that has 4-20mA output, I'm wondering if someone could tell me how to scale current. I know I can put resistor accross the output to produce voltage but I want to do it in current.
Here's my hardwares:
Cole Parmer - Pressure Transducer
Power Input: 24vdc
Output: 4-20mA
Range: 0-100 Psi
PCI-6024E (I also have PCI-6259)
SCB-68
Thanks!
KowdTek
LabVIEW 2009
One Step At A Time, Maybe Two...

Both test works just fine. I also test the input receiving a signal out of regular power supply.
This 6259 is realy flakey to me because we have another PC that has the same daq card and when I tried the code it works.
It's just too expensive to act up like this.
Thanks for your time Sam!
samantham wrote:
Hello,
Lets try testing the 6259 by creating an analog output 5 V and wiring it into an analog input channel. Another good test will be to send a 0-5 V sine wave into an analog input to check its response. All this testing in independent of the code and configurations you are already using.
Then, I would suggest testing an analog input with your code but where the signal is coming from an analog output from the 6259 rather than the sensor. I understand your code is intended to test current. So this last test would be without the 249 ohm resistor.
Let me know if the 6259 is working with these tests.
KowdTek
LabVIEW 2009
One Step At A Time, Maybe Two...

Internal sales employee number range

Dear experts,
Under the same client in SAP system, different company codes can NOT have different Internal sales employee number ranges in the standard SAP, right? In other words, only one number range actiavtes for all the company codes as long as they are against the same client.
Plz corret me if I'm wrong. Many thanks.
Example:
log on SAP - client 800
client 800 has 2 company codes: 1001, 1002
Request:
sales employee under company code 1001: 10xxxxx
sales employee under company code 1002: 20xxxxx
ps. Currently HR module is not applied to client 800. Two years later, HR will be applied.

Hi,
It is possible with userexit NUM_NR_ORDER
ask abaper to add the fields like company code
thanks,
Rahul

Sales employee number range

Dear experts,
Under the same client in SAP system, can different company codes have different sales employee number ranges? If yes, should I just activate the number range? You know, there's no number range assignement to company codes.
Plz help. Many thanks.
Example:
log on SAP - client 800
client 800 has 2 company codes: 1001, 1002
Request:
sales employee under company code 1001: 10xxxxx
sales employee under company code 1002: 20xxxxx
ps. Currently HR module is not applied to client 800. Two years later, HR will be applied.
Edited by: Cathy on Sep 2, 2010 2:46 AM

There shouldn´t been any troubles with different number range. You have to be sure that you have the different number range create in PA04 and that in feature NUMKR you asign a diferent number range to each employee subgroup. For example, if you have number range "01" for sales employees and number range "02" for the rest of employees, your feauture must be something like this:
Numkr
   Employee Subgroup
        SE (sales employee)
          01
        else
          02
After you activate the feature it should work ok, if everything is done correctly in PA04 and in the feature.
If it´s not working I am not sure what could be happening.
Hope I can help you.
Regards,
Edoardo

How To Reset Mac Mail 3.6 To Default Settings

Hello Mac People!
6 months ago I was using a third party tool with my Mac Mail. The tool added an auto BCC address to every outgoing mail. I no longer use the tool and deactivated the third party tool. But there was an error in deactivating and the BCC address is still attached to every outgoing email. I asked the third party tool and they tried everything to fix it, but nothing worked.
I visited the Genius Bar and they said the only way to fix it now, would be to reset my Mac Mail to the original settings (aka start all over) and then re-add each email account, folder, rule, preferences, etc.
It's a pain, but I have to do it.
Problem is I forgot how to save all my current emails in Mac Mail so when I reset everything I can re-import my current emails.
I also don't know how to reset Mac Mail to its original settings.
Please help. Thanks!

Thanks GS,
I did do this with the Genius Bar, but possible we missed something, so here's a list of what was in each folder:
Home/Library/Mail/Bundles > Nothing in this folder
/Library/InputManagers > 1 folder (http://screencast.com/t/YjdiMjRmM) I think unrelated
/Library/Internet Plug-Ins > Several files (http://screencast.com/t/ZTk3M2QyOD) most I know are not related, a few I don't know what they are from.
Home/Library/InputManagers > I don't have this folder
Home/Library/Internet Plug-Ins > 2 Files (http://screencast.com/t/Y2ZhZmM0) I think unrelated
Ok let me know if this makes any sense to you. Thanks!

How to reset Current Employee No Range

Similar Messages

Maybe you are looking for