How to revert stock in quality stock after qty issued with movemt type 704

Hi Experts,
User issued qty from quality stock to cost centre trough T-Code MI10. Inspection lot against the issue qty has status u201CREL CALC SPCO PRII CROK QLCHu201D This lot has been generated through mov 101 against PO (GR). After doing GR qty posted in quality stock. By mistake user has issued qty from quality stock to cost centre trough T-Code MI10. For same movement type was 704.
Now they want same qty back in quality stock also they want to do UD for the same. How to get back this stock in quality stock?
Awaiting for your expert reply.
Thanks and Regards,
Sandy

hi Sandy,
Quickest and easiest option without lot of configuration and process change for your scneario will be ,
The transaction code is MB0A.
The steps for executing the above trancode is as follows.
Inputs:-
Posting date : UD date.
Movement type : 102
Enter relevant plant, storage location, vendor and the material code
The purchase order/sch.agreement for the given vendor-matl-plant combination will be displayed.
Select the correct PO and click adopt selected.
The material with quantities to be reversed will appear in various line items. Select the correct quantity for which the reversal to be made.
Click adopt + details
Enter storage location
Remove "X" in the stocktype field
Save.
Material document will be generated.
The correct material could be inwarded again and correct usage decision can be taken against this lot.
Get approval from Materials and Finance guys.   As long as your accounting documents nurlifies each other , you should be good to go.
If not you have to use the same proess   witht twiests , with other movement types for which you have activated inspection type.
Hope this helps
Cheers
Rav

Similar Messages

Tap to click not working properly in Mountain Lion. How do I get apple to fix this major issue with mountain lion?

The tap to click does not work with mountain lion as it did before the mountain lion install. I purchased a brand new imac in August of 2011 and got a wireless keyboard and selected the wireless trackpad instead of a mouse. The trackpad worked wonderful pre upgrade with tap to click. Now after the install of the newest beast, I have to actually press the trackpad rather than a slight tap. I have carpel tunnel and this is causing great stress upon my hand. How do I get apple to fix this major issue with mountain lion?

Perhaps, I was not clear enough.
I have an imac purchased in Aug. 2011 which came with Lion 10.6 (two uprades before mountain lion)
Recently, I just purchased a macbook pro retina with Mountain Lion
On my imac, my settings allowed me to "tap to click" everything EXCEPT the initial log in at the star up of my imac, again running Lion 10.6
On my macbook pro retina which has Mountain Lion, I set up the "tap to click" option, but notice that a "hard" click was neccessary when trying to click things. I thought this was a macbook thing (my first one) so I went and upgraded my imac to Mountain LIon, BIG MISTAKE! Now both my imac AND my macbook only have limited "tap to click" options. Before mountain lion I could "tap" to highlight and select text, tap and drag, and many other thiings that Mountain Lion has disabled.
I am truly surprised that no one has noticed this MAJOR issue.
Is there a way to uninstall this update, similar to how on a PC you can go back to a restore point.
On another note even the way PREVIEW has changed is less user friendly, there used to be icons on the bottom right corner of the screen, now I have to double tap and select the option I would like to switch between contacts and thumbnails. This is really annoying and is causing me time when reviewing files.
Just in case anyone was wondering, I did go to system preferences -> trackpad -> select tap to click
In fact almost all of the trackpad functions have been selected.

HT201210 The iPod "iPod" could not be restored. An unknown error occurred (1).This is my Ipod 32 GB, which is out of warranty and is 1G-A1213 and had gone kaput, after having issues with iTunes Software as it was not able to run Music on my IPod when conn

The iPod "iPod" could not be restored. An unknown error occurred (1).This is my Ipod 32 GB, which is out of warranty and is 1G-A1213 and had gone kaput, after having issues with iTunes Software as it was not able to run Music on my IPod when connected.
I have wasted my precious 2 days and nights and am lost all my hope...APPEAL TO ALL GEEKS TO RESOLVE MY ISSUE ON HUMANITARIAN GROUNDS ATLEAST WITH SOME VALID TIME OF YOURS.
All mails can be sent to [email protected]
Restore of Ipod back up is present...but is not getting restored due to some iTunes issue with playing my music files.It says restoring and extracts but failes in 1 min with the said error.

Other users and reported error 1 but I have not seen a solution.
Make an appointment at the Genius Bar of an Apple store.
Apple Retail Store - Genius Bar

QM: How to Move material from quality stock to unrestricted stock

Hi,
How to post material stock from quality to unrestricted without using 321.
Regards,

Hi,
if you have quality management active then you have to mainttain quality view in material master along with the inspection lot settings. now this will result in quality lot creation at the time of GRN. then you have to execute QA32 and get the lot. make usage decision and there you will find tab with lot quantity. there you have to give qty in unrestricted and save it.
if you dont have it then just do the transfer postingeither through MIGO or MB1B with movement type 321. give the mat. plant str loc. qty and save it.
regards,
Adwait Bachuwar

Move quality stock to quality stock

Hi,
I have a requirement where i want to split my quality stock with different batches in the same storage location. I tried doing it with movement type 323 in MB1B but it throws me error as "Change the inspection stock of material 25-0323-08 in QM only".
Can someone please help me what to do next?
Regards,
Alok Tiwari

If your material is managed through QM (inspection lot) then system won't allow you to post QI stock from QI through movement. You have to manage QI stock through inspection lot.
What about material transfer through inspection lot stock posting tab? Go to inspection lot and post stock to "To new material" field and enter new material & batch and save your entry.
Hope this should work in your case. Revert back if any question.

Customer consgmt stock to quality stock

Hi experts,
I´m using a consignment stock scenario for some customer in SD.
Depends on the transaction to, for example, returns delivery for the sales order, the system uses 632 or 634 standard movement type. This mov. type affects the unrestricted stock.
My question is, there are a standard movement type to return the materials to a quality stock instead to the unrestr. stock? This is because I have to put the material in this stock (quality) and then, in another process, move it to the unrestricted stock.
In case I need to create a new movement type to do this, where can I specify the type of stock (quality, blocked, unrestr) that the movement type will afect?
Thanks in advance,
Mairo.

HI
For MRP calculation Only following stock can be controlled (this setting is available in OPPQ transaction)
Stock in transit
Blocked stock
Restricted stock
Regards
Anupam Sharma

IWeb not opening after some issues with an existing site...

Hi there~
I’m a relatively new Mac user and a former PC/Dreamweaver user. I’m having a bit of an issue with iWeb. I’ll do my best to keep what happened relatively brief:
1. I had created and published a site a couple of months ago, but the page that contained photo albums seemed to have become corrupted. Every time I tried to open that page, iWeb would crash.
2. I recreated that page but then was not able to delete the corrupted version. So I recreated the whole site.
3. I published the new site, and everything seemed to be working well in the live version.
4. To avoid confusion in the future, I wanted to get rid of the old site. When I deleted that site, I saw that it said something about deleting it from the Web as well. I realized that this may cause problems because most of the pages would have the same names, but I was hopeful that since the new site had all of the pages I could just republish.
5. The new site did indeed get messed up after I deleted the old site. So I set the new site to republish, and then I got an error message.
6. I figured just for safety’s sake I would undo the deletion of the old site and just leave it for a while in the hopes that the new site would then work again.
7. After I did this, the old files reappeared, but then iWeb froze. (I think... My memory is a little fuzzy here...)
8. I closed and reopened iWeb, but all that appeared was that little right-hand box that lets you see the properties of certain things (Page, Photos, Text, etc). I also restarted the computer, and now when I open iWeb, that little box is still all that I’m getting.
I grabbed what I could from the live version and my history files so that I can recreate the site from scratch if I need to, so I’m not terribly worried about getting my files back. I did have another site created in iWeb that seemed to be fine, it would be nice to not have to start over with that one, but obviously I can if needed. Maybe those files can be found elsewhere on my computer?
So will I be able to get iWeb back? Do I need to reinstall it? If so, how do I do that? (Maybe that’s a question for another forum. iLife was installed on the Mac when we got it, I looked briefly for the files on the Applications CD but got a little scared off when I saw something about bundled applications...)
Thanks so much for any help. I called tech support and was directed here, this is new for me, so I hope I’m going about this in the right way. I’ll spend some time looking around to see if anyone has addressed this elsewhere, I just wanted to get things down while it was all relatively fresh in my head.
Thank you!
Jen

Welcome to the Apple Discussions.
. Every time I tried to open that page,
That sounds like the problem described here with potential fixes: iWeb & iWork: Applications may suddenly quit after updating to Mac OS X v10.6.2. This is another possible fix: The million dollar trick or how to fix iWeb in 10.6.2
OT

CD-ROM drive letter changed to the next available letter after an issue with the Storage appliance.

Server platform:Windows server 2008 R2 Enterprise.
Last time we experienced an issue with the storage device we are using to attach a disk to our server 2008 (virtual). This storage device is also providing storage to the ESX where the server 2008 is hosted.
The drive configuration in the server was:
System C:\
Tools D:\
Apps E:\
CD-ROM F:\
Some hours after the storage appliance issue, we realized the Application on the server was not working and then we restarted the server. After restarting the server we went to the file explorer and realized that the Apps volume had the drive letter F and
the CD-ROM had the E letter assigned.
I assume windows lost the Apps disk due to the SAN disconnection. Maybe the CD-ROM was also disconnected and when the Storage appliance was connected again the CD-ROM acquire the next drive letter it found, which was the letter E:. Then the Apps disk was
also discovered by Windows and it assigned the next available letter, F:.
I was looking for some MS knowledge base to see how Windows 2008 server assigns the letter to the CD-ROM and how we can permanently fix the letter assigned to the disks and the CD-ROM so that this issue won't happen again. As you know many applications use
the path including the drive letter.
I thought that when you set a CD-ROM drive letter, it remains forever as is, and that in case of a SAN disconnection Windows assigns the same letter the drive had before the disconnection.
Please advice if you have some documentation about this. And let me know if you have any thoughts about what really happened to prevent this in the future.
Thank you guys!!

Hi, for the APP's drive it could had been assigned a new letter if the system did seen it as a new disk/partition.
The partition was on your esx's LUN on the SAN ? (not an iSCSI connection from inside a VM?)
Regards, Philippe
Don't forget to mark as answer or vote as helpful to help identify good information. ( linkedin endorsement never hurt too :o) )
Answer an interesting question ? Create a
wiki article about it!

After installation: issues with TOC subchapters

Hi all,
I noticed that after installation on a device there were two issues with subchapters in the TOC (i.e. what would be books in a classic Webhelp or HTML Help).
1. Wrong jumps
When jumping into the submenu of the TOC and when returning using the 'back' button at the top of the submenu, there is often a wrong jump to an arbitrary topic of the project. This was consistent in a particular output, but if I simply generate and install the apk again then it is usually gone or a different submenu show this problem.
2. System default styles applied
Instead of using the hover and active colors defined for toc nodes in the Screen Layout (e.g. brown in the iPhone layout), the default highlight colors of the mobile device (e.g. green) are applied. This is only the case when jumping into a submenu or back, not for other actions of the apk's UI. It seems that perhaps a CSS definition is missing in the mobile.css?
I tested this using the Android phone and iPhone layouts. None of these problems occur when viewing the HTML 5 output in the browser. Does anybody else encounter these problems / know a solution?
Robert

Solved: the mystery of the erratic jumps.
The reason is an inaccurate control. If I touch the display with my finger tip at the vertical middle of a TOC entry and with the lower part of my finger tip also touching into the next TOC entry, then the app highlights the first entry but jumps to the second target.
Maby an issue of the HTML5 code, maby an issue of my device..
Addition: I tested it on two other devices and they show this issue too, although to a varying extent depending on screen resolution. The problem remains that if the user touches the fields inaccurately then the software sometimes highlight one TOC entry but jumps to the next entry's target.

Reversal of unrestriced stock to quality stock

hell,
any body pls explain me when i am doing revesal stock tranfer from quality to unrestriced stock in MB1B through 322 Movement type its giving error as transfer the material through QM only. actually my client accendently tranfer the rejected material in unrestriceted stock he wants do reversal. how can i do.
thanks & reegards
bhakta

Hai,
      In your case , you can deactivate the inspection type in MM02,if no stock is avaliable .
      if any stock is avaliable ,the system would not allow to deactivate.
     Once the it is deactivated, you activate the stock tranfer inspection type such 08 in mm02 and move the stock through mb1b .
     when tranfer the stock , the inspection lot will be created and the stock will be moved to quality.
     kindly check this and revet back
Thanks & Regards
jai

Storage location is not updated after posting GR with Mvt type 107(Valuated GR blocked stock)

Hi experts,
Before posting GR through Movement type 107 (valuated GR blocked stock) we can see the storage location field in MIGO screen and able to enter value into this field. But after posting GR when we retrieve the material document we are finding that the field (storage location) is blank, i.e. it's not updated at all. When we check the stock in MMBE we find that no quantity is updated for valuated GR blocked stock.
We want the storage location to be updated while posting GR with 107 Mvt type.
Any idea Please?
Points assured.
Thanks
Amitava

SAP describes it in help.sap.com: Since the material is not to be added to the inventory yet, do not enter a storage location.
If you require a storage location, then I assume that your design does not match with the design of SAP, you are using a function to solve a gap which is not foreseen by SAP for this case.
Especially the 107 is usually representing stock which is still in transfer but you are already the legal owner and have to show the value of those goods in your books.

Process & Form:HCM How to revert back from quality to dev server

Hi All,
I have created form and process its was working fine,then move to quality server,later some new requirement occur then i changed in the development server but after some changes its giving dump error if i test the process by t-code- HRASR_TEST_PROCESS
I am not able to find out what changes cause for the error so i want to revert back to last version of form or i can say remove the new change that cause the problem occurs,Is it possible if yes then pls help in with what are the step is required to do.
Thanks In advance...

Hi Vijaya,
You just need to change the preferences of Quality server and deploy the DC. No need to copy the local DC manually. You should have SDM password to deploy this application.
Go through the following thread:
moving Local Web Dynpro project from Dev to Prod
Thanks n Regards,
Jhansi Miryala

How to revert to 10.6.5 after installing 10.6.6?

Hey guys, is it possible to revert 10.6.6 to 10.6.5 without formatting? Or do I have to format my OS X?

Stop wasting this guys time by sending him to the speed FAQ.
He clearly didn't report having speed issues until 10.6.6 update.
Yes, and people have been blaming problems like these on system updates for as long as there has been a system to update. It's very ironic that people are now talking about reverting to 10.6.5 to get a stable system... just a couple months ago, all the talk was about reverting to 10.6.4 because 10.6.5 had "bugs". And before that, it was 10.6.3 that was stable and 10.6.4 that was not. And so on.
The fact that the problems appear after an update does not mean that they are caused by bugs in the update. An update like this changes hundreds or thousands of files, and if there's any corruption in the system or the hard drive's data structures, those kinds of changes can result in a destabilization of the system.
It is too early to say for sure that the 10.6.6 update has no problems. However, it certainly hasn't caused any for me or for a number of other experts on these forums. Blaming problems on Apple and waiting for them to fix it is not productive when the problem is not likely to be theirs.

How to revert back to iMovie 9 after reinstalling Mavericks?

Good Day All,
I recently had to reinstall my OS (OSX Mavericks) for my MacBook Pro 13-inch Mid 2012 Model. Prior to this, I had iMovie 10 (yuck), AS WELL AS the old iMovie, which had remained behind in my applications folder (iMovie 9).
Before I reinstalled the OS, I made sure to copy the iMovie 9.0.9 application to my hard drive, and once a clean OS was installed, I made sure to drag iMovie 9.0.9 back to my applications folder and run it, however I am met with an error:
iMovie 9.0.9 has failed to start (not the exact words I cannot remember, as now whenever I launch it the icon pops up in my dock and than a split second later disappears)
Is there anyway I can get iMovie 9.0.9 back after a clean OS install?
I already downloaded this: http://support.apple.com/kb/DL1574 (the iMovie 9.0.9 update), however it fails to work, as the only iMovie I have on my machine is the horrible iMovie 10, and it required an older iMovie to update too.
Any help at all will be very appreciated.
Thanks
_celis_

try this code
TYPES: BEGIN OF ty,
sal TYPE i,
END OF ty.
data: a TYPE i,
      2a TYPE i,
      itab TYPE STANDARD TABLE OF ty WITH HEADER LINE,
      itab2 TYPE STANDARD TABLE OF ty WITH HEADER LINE.
itab-sal = 10.
APPEND itab.
itab-sal = 10.
APPEND itab.
itab-sal = 11.
APPEND itab.
itab-sal = 9.
APPEND itab.
itab-sal = 15.
APPEND itab.
itab-sal = 9.
APPEND itab.
loop at itab.
LOOP AT itab2 WHERE sal eq itab-sal.
ENDLOOP.
IF sy-subrc eq 0.
else.
APPEND itab to itab2.
ENDIF.
ENDLOOP.
LOOP AT itab2.
WRITE:/ itab2-sal.
ENDLOOP.

How do I restore contacts to outlook after a sync with icloud?

I did the same exact thing, for the same reason as below, and have the same problem now.
rstone32566 Sep 16, 2014 2:22 PM
Re: Can contacts moved fr Outlook Contacts be restored in response to rstone32566
Hi Norm123
I had set-up iCloud Control Panel on the new computer. I did get the contacts from iCloud back in my new computer, but they are in a new Contact folder that is apparently separate from the original Contacts Folder. Now on my new PC, when I open Outlook and go to Contacts, Outlook shows two separate folders under My Contacts, both of which are labeled "Contacts". One apparently came from iCloud, but the other is empty and appears to be the original Outlook Contacts folder. I say this because the empty Contacts folder cannot be deleted, i.e., right clicking on it doesn't provide any option to delete it. The other Contacts folder, which appears to mirror the one in iCloud, does offer this option to delete.
Then in Outlook on my new PC under the All Contacts column I also have a folder selection named "Contacts in iCloud", as well as a selection of a group of sub-contacts that I had originally set-up on my iPhone. This subset of Contacts is maintained on my iPhone and was also intentionally shared with iCloud.
What I really had hoped to do initially was to maintain my PC's original Contacts on my PC, but to share the file with iCloud so if I was away from home I could look up a primary contact on my iPhone by opting to view them via iCloud.
The other problem I have now is that when selecting Contacts on my iPhone, my only choices are to view the contacts that I originally set-up on my iPhone, or to view a selection called All Contacts, which displays not only the contacts that originally came from my PC, but merges them in with the contacts set up on my phone. Of course this gives me a list of contacts that includes double entries for every contact that was set up on my iPhone and who is also in my PC's Contacts folder.. In other words, on my iPhone I can select the group set up on my phone by itself, which is great, but if I check the "All Contacts" group on my iPhone it will not allow me to unselect the group set up on my iPhone.
I wish your original suggestion to export vcards from the iCloud worked as the link you gave me described. I can seem to re-populate the original Contacts folder on my new PC by importing the vcards, but I can only get this to work one contact at a time. Selecting multiple contacts doesn't seem to work.
Thank you very much for all your help. I hope the feedback in this message makes sense. If you find out how to get the multiple selection export to work as advertised, please let me know
Best regards,
Bob (rstone32566)

If you downloaded iWorks apps under the ID you are using on your iPad, regardless of whether you erased it or not, the apps are still tied to that ID.
Have you signed in to the App Store on your iPad?
Settings > iTunes and App Store
Tap your Apple ID and if you have not signed in, sign in using the same Apple ID and Password.
The same should be done with iCloud.

How to revert stock in quality stock after qty issued with movemt type 704

Similar Messages

Maybe you are looking for