How to set a static IP address on a Mac server?
I am setting up a New Mac server for a mail sever and have resieved the MX record and IP address from the ISP and DNS providers. Now I am trying to set up the server to be seen on the out side, or even on the network. Is this all done in the Network confiruration by maually setting the IP and Sub Mask there? I have set it all up to what I think they should be but not having any luck. When I installed the server software I told it to be a stand alone server was that wrong. I will not be running DNS or any other services on this system only Mail.
thanks
You should enter the IP address/netmask, etc. during the first-time-boot setup. Changing it later can be a PITA, but it sounds like you did that.
Setting 'standalone' shouldn't be an issue since that only relates to directory services.
It sounds like the problem is a more basic connectivity issue.
Have you verified that you have basic IP address connectivity? Can you ping the router address provided by your ISP? Can you ping remote sites outside your network? If that's not working you're not going to get much further.
Similar Messages
-
How to set a static IP address for deskjet 6940dt
I have two HP laptops, both have WIN7, that keep losing the IP address for my 6940dt printer, each time power goes out to router. I have an desktop PC connected to a NetGear router and RCA modem connected to Comcast cable internet. I also have another desktop that connects wirelessly through the router....but this desktop never loses the printer IP address and I can't figure out why it doesn't and my laptops do.
I have had a fellow at the senior center computer club tell me that I need to set a Static IP address to make the laptops connect . I don't know how to do this and I would need someone to explain it in a language that I can understand, like real basic. I have searched the internet but the things I have found have been very complicated to understand.
Can anyone help me?
This question was solved.
View Solution.Ooops, sorry, I forgot that yours is a wired-only network printer.
You are on the right track - just go to where you were and follow my directions - it all works the same with wired as it does wireless.
Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
I am employed by HP -
How to set a Static IP Address to a HP Photosmart Plus B209a-m?
Like it says up in the subject, I need to know how to do this. I tried to do it by typing in the IP of the printer into a browser, but then I lost connectivity with it all together. If someone could help, that would be amazing!!
Thanks in advance!
TechGirl88First, let's see if your printer is actually connected to your network.
- Print a Network Config Page from the front of the printer. Note the printer's IP address. If it is 0.0.0.0 or 169.254.x.x then the printer is not connected. You will have to re-connect it using the same method you did originally.
Now that it is connected, this is how to set a static IP:
- Type that IP address into a browser to reveal the printer's internal settings. (if this does not work, you likely have a firewall and/or security system blocking it - please advise).
- Choose the Networking tab, then Wireless along the left side, then the IPv4 tab.
- On this screen you want to set a Manual IP. You need to set an IP address outside the range that the router automatically sets (called the DHCP range). If you know what that is, set an IP outside that range but no higher than 254 (the last number in the address). If you do not know this, enter the current IP address.
- Use 255.255.255.0 for the subnet (unless you know it is different, if so, use that)
- Leave the gateway and DNS blank. Click 'Apply'
Now, shut down the router and printer, start the router, wait, then start the printer.
After this you may need to redo 'Add a Printer' using the new IP address.
Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
I am employed by HP -
PowerShell script to set VM static IP address - multiple subscriptions
Hi,
I have set successfully static IP Address to all of my virtual machines until now (1 subscription) using Set-AzureStaticVNetIP
But now I have 2 Azure subscriptions. The virtual networks names are the same at both of the suscriptions.
The question is:
How to define the subscription to use when defining static IP addresses to VMs?
Thanks in advance!Hi SCCMadmin09,
Considering that you have successfully set static IP Address to all of your virtual machines until now for one of the subscriptions :
Login to your Azure account with the command ; this time you should be entering your second subscription login credentials.
Add-AzureAccount
Add-AzureAccount
: This will open a windows login dialog that will allow you to enter your credentials of the second subscription.
Now you need to find the name of the subscription you created your virtual machines under. The command is:
Get-AzureSubscription
The output will give the Azure subscription information
Here in the example, Visual Studio Ultimate with MSDN a/c is used. The command to select this is:
Select-AzureSubscription
: Select Azure Subscription: Enter your subscription name and then ENTER:
Eg : Visual Studio Ultimate with MSDN
At this point you are connected to your subscription and can begin to work with the virtual machines created under it.
There are two parameters you will need to have:
ServiceName
= the name of your virtual machine. Example :
DTechHST-Test01
Name
= the same name you entered as the ServiceName
And finally the commands, there are three.
Get-AzureVM -ServiceName <your_vm_name> -Name <your_vm_name>
Set-AzureStaticVNetIP -IPAddress "<your_new_ip_address>"
Update-AzureVM
Unfortunately, entering these commands one at a time fails. They must be strung together via “pipes”.
Get-AzureVM -ServiceName <your_vm_name> -Name <your_vm_name> | Set-AzureStaticVNetIP -IPAddress "<your_new_ip_address>"
| Update-AzureVM
As an example:
Get-AzureVM -ServiceName HST-Test01 -Name HST-Test01 | Set-AzureStaticVNetIP -IPAddress "192.168.224.50"
| Update-AzureVM
In the event that you need to remove an assigned IP address, use the following command structure.
Get-AzureVM -ServiceName
<your_vm_name> -Name <your_vm_name> | Remove-AzureStaticVNetIP | Update-AzureVM
Hope this helps.
Regards,
Shirisha Paderu -
How to set and static ip_address for a Suse Linux box
Hi.
I've done the following to set an static ip address for my Suse 9 Linux box:
- Take not of inet address value from ifconfig command. ie: (172.17.2.14)
- Change this value in /etc/hosts for my linux box.
Since Suse is configure by default to use DHCP for assigning dinamic ip_addresses i'm not sure whether will lastly be set as a static address. I've rebooted my box and it seems to be OK.
Thanks in advance ...!/etc/hosts is not configuration file for ethernet interfaces.
Configuration files for ethernet interfaces are stored in /etc/sysconfig/network directory.
For example if you have eth0 device then configuretion for this device is stored in /etc/sysconfig/network/ifcfg-eth0 file.
Important directives:
DEVICE - interface (eth0)
IPADDR - IP address of interface
NETMASK - netmask
BOOTPROTO - "static" for static configuration, dhcp for dynamic configuration via dhcp
ONBOOT - activating interface during boot (yes/no) (yes - of course :-) )
GATEWAY - default gateway
So for example you want setup static IP (192.168.10.1 / 255.255.225.0) for eth0 interface.
Edit the /etc/sysconfig/network/ifcfg-eth0 file and your configuration should be:
DEVICE=eth0
IPADDR=192.168.10.1
NETMASK=255.255.255.0
BOOTPROTO=static
ONBOOT=yesThen you simply restart the nework using:
/etc/init.d/network restartOR
/sbin/ifdown eth0
/sbinf/ifup eth0 OR
ifconfig eth0 down
ifconfig eth0 up -
How to set a rescue email address when I already have an Apple ID. Actually I forgot my security questions.
You won't be able to add one until you can answer your questions, you will need to contact iTunes Support / Apple to get the questions reset.
Contacting Apple about account security : http://support.apple.com/kb/HT5699
When they've been reset you can then use the steps half-way down the HT5312 page that you posted from to add a rescue email address for potential future use -
Setting up Static IP addresses
In the FAQ entry for setting up static IP addresses, it says to set the "Preferred DNS server" to: 192.168.1.1
Currently, mine is set to: 68.94.156.1
with an Alternate DNS Server of: 68.94.157.1
Now, I'm wondering, does the Prefered DNS [i]have[/i] to be 192.168.1.1 or will what I currently have work just as well? Also, am I supposed to have an Alternate DNS server, and if so, is what I currently have it set to fine? Lastly, do the DNS servers have to be different for each computer?
Any help would be great. I'm hoping to try and re-setup my router tonight.Kind of off topic, but don't want to make a whole new thread...
Currently, my home network is very messed up. Previously, we would lose connections upwards of 4 times a day.
At first, we thought it was because our modem was getting old. So my dad bought a new modem. But when he finished hooking up the modem, we still couldn't connect to the net, so he plugged his comp directly into the modem instead.
Now, in an attempt to get things working, I have reconnected the router, modem and computers to eachother. However, there is a problem. I can't access the router's setup page from my computer anymore. The lights on the router and modem indicate that:
1. The modem is connected the net.
2. The router is connected to the modem.
3. 3 devices are plugged into the router.
Now, I have two wired comps, 1 x-box and a wirless comp. and I am using the WRT54G router. I don't understand why this computer cannot connect to the router. I know it is just this comp, because the wireless one can access the router's setup page, although it still can't connect to the net.
Could someone give me an idea as to what the problem is? The only thing I can think of is, maybe instead of running a cable from the router to the computer, I ran it from the printer to the computer (they are right next to eachother). But don't think printers even use ethernet cables. -
How to set a static IP on wrt1900ac
I am trying to set some static ip addresses on my new router I go to the advanced routing section and put in the info but when i get to the gateway it says the specified gateway ip is invalid.
If the ISP modem has a built in router, it's best to bridge the modem. Having 2 routers on the same line can cause connection problems: Link>http://www.practicallynetworked.com/networking/fixing_double_nat.htm and http://computer.howstuffworks.com/nat.htm If the modem can't be bridged then see if the modem has a DMZ option and input the IP address the router gets from the modem and put that into the modems DMZ. Also check the routers DHCP IP address maybe conflicting with the ISP modems IP address of 192.168.1.1. Check to see if this is the same on the ISP modem, and if modem can't be bridged, change the Linksys router to 192.168.0.1 or .0.254. If your trying to set Static IPs on the LAN side then Static IPs are configured on each devices thats connected. This can be done for devices lilke printers, controllers cameras and NAS. This should be done outside of the routers default DHCP IP address pool. Other devcies like PCs phones, Pads or game consoles that need router management, then it's recommended to set a Reserved IP address ON the router for these devcies. For WAN side or ISP side Static IP services:http://community.linksys.com/t5/Wireless-Routers/WRT1900AC-WPA2-on-Guest-Network-and-Setting-Domain-Name/m-p/960821#M305633
-
How do set up your hotmail account on a mac book pro properly? I have it set up so I get mail but on my hotmail account I have lot of separate folders to save messages in(for example :- bank, skyp, work, Facebook, apple, ect...). They don't show up on my mac. I also have an iPhone and iPad, there is no issue here when I set those up. I automatically got my separate folders. Anybody have any idea or encountered the same problem?
Leuvy13 wrote:
Cheers,
I'm not gonna lie, I actually have no idea if its pop or imap. Do you know where you can check and if it can be changed?
Hotmail on a Mac is POP3 only, you will only get the basic folders (inbox, sent, trash etc) and it will not sync with other devices.
And now I post this I see other replies, so this is redundant. !! -
HT1637 How can i change my email address on my mac to my new email as my other one has been hacked
How can i change my email address on my mac book air email that has already been on the mac book air to my new email as my old email address has been hacked and it will not let me change it
Call the tech support for the provider of your old email. They will be able to change the password for you or if they can't they will shut the account down so that spammer is not able to use it.
Allan -
How do I create a DNS record on my Mac Server?
How do I create a DNS record on my Mac Server?
The following is info that I found in another post that I have been trying to follow.
MrHoffman New England
Re: Configure DNS - OS X Server Next Steps
Feb 13, 2011 6:36 AM (in response to Jimbooooooo)
You're setting up internal DNS services, you referenced your ISP DNS servers and you should not have, and now those servers have no translations for your hosts. This is a common misconfiguration.
See [configuring DNS on Mac OS X Server|http://labs.hoffmanlabs.com/node/1436] for how to set up your internal DNS server.
And if there are any references to your ISP DNS servers here (within your client settings, within your server settings, your Airport settings, etc), then you're usually going to have DNS and connectivity problems. You're running a server now, so you'll be running your own services, and (particularly because of NAT here) referencing only your own DNS server(s).
You may be setting up external DNS (if and when you need that), but that should happen after you set up your internal DNS. The above article has a link to setting up external DNS, when you get around to that, if/when you need in-bound connections into your LAN. -
How to setup a static ip address and DNS on airport extreme using the iOS Airport Utility?
I am at a location that only has wired ethernet. The ethernet connection has a specific Static IP address, subnet, gateway, and DNS setting. I cannot seem to find how to enter DNS settings using the Apple Utility on an iPad. HELP!!!
First, I am assuming that you are trying to administer your AirPort base station for a static IP address using the iOS version of the AirPort Utility ... correct?
If so, then to do so:
Start the AirPort Utility app on the iPad
Select your base station.
Select Edit
Select Internet Connection
Select Static
Enter the appropriate IP address information
Select Done
Sorry, it does not appear that direct input for DNS IP addresses is an available option with this version of the iOS AirPort Utility app. Not sure why this was not included. -
How to route Multiple static IP addresses
I have 5 static public IP addresses from Comcast Business. I need to host 3 low-volume web sites with distinct domain names which map to unique public IP addresses. I have all three web sites on one computer.
Linksys has told me it can be done (but has NO useful support); and Comcast has told me it can be done. I've searched high & low on forums for a solution but can't find one.
Equipment:
Linksys WRT300N router
Webserver is Windows 2003 with 3 NIC cards
Cable Modem is an SMC 8014
Cable Provider: Comcast Businesss
I already have the router set up for a Static IP and have entered my first public IP address, cable modem gateway and DNS servers. I have also port-forwarded port 80 to the web server. One web site works fine.
My question is: How can I route the other 4 ip addresses to the web server?
TIA,
bertIf you already have set up the forwarding and it does not work for those other IP addresses, then it can't be done with your router. You'll need a router which supports one-to-one nat which allows you to map multiple public IP addresses to LAN IP addresses.
-
How do I assign static ip address on time capsule
I want to assign static ip addresses to certain devices in my home but not sure how to do it through the iMac and Air Port/time capsule
Not sure as I don't own an Apple router but on mosdt modern routers there is a way to set, that is SET, a constant IP for devices by their MAC address, that is Mac, Media Access Control address not Mac computer.
I would think Apple has included that feature in their Airport routers. -
How do you set up multiple IP addresses on a web server?
I have a block of 8 fixed IP address, 5 are useable for websites. I have a netopia router and I would like my server to be able to host several different sites using a secure server. I know you can only host one secure site for one fixed IP address. I have been using one IP address and hosting virtual domains up to now. I don't know how to set the router and the server up to make this work. Everything I have tried has failed. I have tried IP mapping and passthrough but I can only make one IP address work. Not multiple. Any advise would be appreciated.
Since you're looking to host multiple SSL sites, no matter what you do you're going to need to setup multiple IP addresses on your server.
I would NOT recommend running the server at your edge - there are valid reasons for using firewalls and NAT devices. Instead, configure your server with multiple private IP addresses (192.168.x.x or 10.x.x.x, whatever you prefer).
Then, in Server Admin, configure your SSL web sites. Bind each one to a specific IP address.
This is different from your non-SSL web sites, which presumably have 'any' as their IP address.
Then setup your Netopia router to port-forward port 443 on each public IP address to the corresponding private IP address on the server.
Maybe you are looking for
-
Project Expenditure inquiry doesn't show expenditures after 12.1.3 upgrade
Hi, I am puzzled with this issue here. We are currently in the UAT phase R12 upgrade (11.5.10.2 to 12.1.3) some reason one of the super user is not able to look at the expenditures using the expenditure inquiry screen. Everyone else is able to see th
-
Flash player problem in windows 8.1
I am setting up a new Laptop as a gift and am having issues with Flash player in Internet Explorer 11, Windows 8.1. I cannot use Facebooks bulk picture uploader. I receive a notice that Flash Player is not installed. When I go to the Find Flash Play
-
Problem setting up database for dreamweaver 8 to use on testing server
I am trying to try out dreamweavers database features, by trying to set up a connection to mysql database. How ever I recieve errors when trying to select my database. Either I get a long error that says it can not find localhost//_mmHTTP... somethin
-
How Do I Display Custom Document Properties On the Info - Properties Page
Hi, I want to create a template using Microsoft Word 2010 that has fields similar to the Standard Document Property "Title" that can be used as a fillable form that repeats data throughout the document. I need a custom document property field that y
-
Cannot open files from Application Navigator without JDeveloper freezing
Completely bewildered by this... please help. Been using JDeveloper 11.1.1.0.1 Build JDEVADF_MAIN.BOXER_GENERIC_081203.1854.5188 (pointing to Java 1.6.0.16) for a few months now. Every week or so I take a copy of my project (just take the whole proje