How to write an on card installer

I am a newer to java smartcard. I need write a on card installer, what is the first step should i do? Can this program be written by c? Where can i find some samples? Thanks!

Search the forums !
http://forum.java.sun.com/thread.jsp?forum=23&thread=339651

Similar Messages

How to write Wireless PC Card Driver?

Hi, All,
Can anyone help me to find out how to write wireless pc card device driver?
Thanks !!

There are [at least] two examples of PCMCIA dirvers in the DDK supplimentary suite. There is also an example of simple DLPI driver.
All you have to do is to combine those examples to get the PCMCIA DLPI driver and fine tune it to match your particular hardware. Any bells ring?
You will definitely need your card programming manual and/or software interface description for the last phase.
If you do not have one, you might get some open source (say, Linux or FreeBSD) driver for your card and do some code analysis to reveal the information you'll need.
Hope this helps...
Ilya.

How to write a Xml installation file to build web installer using IzPack.

Hai everyone,
I have got a problem in building a web installer using IzPack.I am getting this exception,when I am compiling my install.xml using a compile tool provided by IzPack soft.Eventhough I have not mentioned "packsinfo.xml" in my Xml installation file.
Fatal error :
null\packsinfo.xml (The system cannot find the path specified)
java.io.FileNotFoundException: null\packsinfo.xml (The system cannot find the path specified)
What went wrong??
It is very very urgent. Could anyone tell me how to write a Xml installation file for building web installer,please??
any help will be highly appreciated....
Thank you very much in advance

Hi,
that is not really a java related question. Have you tried to find some IzPack support forum? I've never heard about it, so I can't help.

Sample of how to write data to NI 9802 SD Card C-Module

I have basic knowledge of LabVIEW but now I want to go into Real-Time and FPGA. I want to learn how to write a data read from an analog input to a SD card using NI 9802. For the purpose of learning data rate does not matter, as long as I can write something to the memory card. I read some documents online but I have not found an example so I can understand how to do it. I will much appreciate if there is any help.
My settings:
- cRIO 9073
- Slot 0: NI 9229 (reading only AIO)
- Sot 1: NI 9802 (Memory card is inserted to slot 0) - must be used in FPGA mode only.

Hi,
To getstarted with, you can first attempt to mount and unmount the NI 9802 using the invoke methods "Mount SD Card" and "Unmount SD Card" in the RT vi. For this you only need to open an FPGA reference to the FPGA vi. After Mounting, you can obtain the drive letter and use it to create the file and write data.
Best Regards,
Gogineni
Kudos are welcome

How to delete the duplicate cards in ALUI

Hi,
How to delete the duplicate cards in knowledge directory
Thanks & Regards
Dheeraj
Edited by: dheeraj on Sep 17, 2008 2:31 PM

Not sure if there is an automated way to do this, but I get around it by just searching on (2), (3), (4).
Not practical for large installs, but it works in our small environment.
You might be able to use the Smart Sort utility to find files that have () characters in them? Not positive though.
It would make a great enhancement request to add dupes to either a log file or better yet an admin utility to track the living documents to ensure they are fixed!
(I'm going to file such an enhancement right now!)

How to delete the duplicate cards in alui crawlers

How to delete the duplicate cards in alui crawlers

Not sure if there is an automated way to do this, but I get around it by just searching on (2), (3), (4).
Not practical for large installs, but it works in our small environment.
You might be able to use the Smart Sort utility to find files that have () characters in them? Not positive though.
It would make a great enhancement request to add dupes to either a log file or better yet an admin utility to track the living documents to ensure they are fixed!
(I'm going to file such an enhancement right now!)

How to load a java card applet into a java card

Dear All,
I am a novice to java card technology..
I have done some search on how to load a java card applet into a smart card but haven't found a satisfactory answer. I have read about installer.jar and scriptgen tool but I want to load the applet from a java program and not from command line. It would be of great help if somebody can help me out.
If somebody can share a sample program which load a javacard applet(.CAP file) into a smart card, I will be very thankful.
I am able to find some client applications which help us send APDU commands and recieve response APDU's to interact with an applet loaded on to the smart card but not application which actually load the applet.
I have heard of OCF and GP.. some say that OCF technology is outdated and no longer in use.. can somebosy throw some light on this too..
cheers,
ganesh

hi siavash,
thanks for the quick response.. i checked out GPShell as suggested, it looked like a tool by which one can load an applet on to card and send some sample apdu commands... but I want to load the applet from the code.
My application should look something like this.. it will be a swing applicaton where I have a drop down with a list of readers, I select the one desired and then click on "LOAD" after inserting a blank java card, at this point my applet which is stored in my DB should get loaded on to the java card. The next step should be to personalize it where I enter the values for the static variables of my applet and click "PERSONALIZE", at this point all these values should be embedded into APDU commands and sent to the java card for processing.
For achieving this I am yet to find a comprehensive sample or documentation on the net.
Please help...
regards,
ganesh

How can I choose java card?

I'm new for smart card.
I want to do project about security (It use authentication by MAC.) How can I choose the card and reader/writer? Have vender in thailand?
If I bought normal smart card and reader/writer, can I write java on it? If it's possible , how can I do?
Note that: I want only basic java card.
Thanks

I go to Schlumberger website. I found e-gate SDK kit ID. 401140.
I want to know that it have more basic can I get to do my project?
About gemplus? I go to gemplus website too, but I don't found more enough information to decided.
Cloude you advise version of card and reader that can I get to do my project? (I have budget about $250)
Can it work with Java Card 2.2 Development Kit by sun, if I buy only card and card reader?
Thanks,

Network card installation

I've tried installing 2 different network cards (Linksys TNE100TX; 3COM 3C509B Etherlink III). I think my problem is that I'm a novice user and don't know how to install a network card and assign an IP address. I've found the Linksys card on one HCL (although it's not listed in my Solaris 8 documentation on my disk), but can't find the 3COM card. Are either one of these cards compatible? Do I need drivers?
I'm on an Intel platform with Solaris 8. I am connected to a Linksys router (to share my DSL line). The router has a fixed IP address from PacBell, but uses 'DHCP' to assign IP addresses to my 3 computers.
How can I let my UNIX system know I'm using DHCP?
How do I assign the router IP address? Do I use the route add default command? Do I use the default gateway address or the router IP address for this?
Do I need a DNS/hosts table? Should I edit the /etc/nsswitch.conf file to add 'dns' to the 'hosts' line?
Do I need to edit the /etc/resolv.conf file, putting in my primary and secondary name servers (from Pac Bell)?
Also, on boot I get an error message: Can't register INT for PCIclass, 0C0300 device at IPL 1 because conflicts with IPL 14. Can you explain what this means and how to correct it?
As you can from my questions, I know some terminology (from my books), but don't really have a good grasp of what I am doing yet. I just started learning UNIX.
Thanks for any help you can give me on this.
Bill Lazar

Recently I have installed S10 b63 on a X86 PII machine.
Regarding the 3com nic - 3c905c - the installation and running with elxl driver was ok.
Now I want to change this nic for an other 3com nic -3c905, but encountered following problems:
When I put new nic in same pci slot and boot up solaris I get a row of errors and don't get trough the boot process.
-Errors are caused e.g. by the different MAC address of the NIC, and therefore no NIC is recognised at all.
-Boot hangs because a NSF request is made at boot, but is not rewarded as NIC is not active.
Changed my strategy to adding a second 3com NIC (both using the elxl driver) and followed the hints from Juergen Keil (above), but " ifconfig elxl1plumb " results in "no such interface"
I have looked on the web and in the documentation for a solution, but so far I have not found how to go about this, other that doing a complete new solaris installation.
Any help appriciated !

"Unable to Write to SD Card"

I received the message "Unable to write to SD card" while trying to export some data from an app to my SD card. How do I regain the ability to write to my SD card?

CellDaddy,
I'm happy to help with your SD card. What information are you trying to move from the application? Does this happen on multiple apps? If you go into Settings>SD card, what is the available storage for the card? If you insert the SD card into the computer, are you able to view the files properly? Let me know!
Thank you,
AdamE_VZW
Follow us on Twitter @VZWSupport

How to write ACPI device driver for Solaris 8 (SPARC Edition)

Hi, All,
I wonder how to write ACPI driver to access battery life,
can anyone help ? thanks!!

I am having the similar problem identified in this thread.
OS: Sun Solaris 10 01/06
Hardware: Sun Blade 2500
PCI Memory card.
Problem: When driver moves more then 40 bytes via PIO from a PCI device memory card, the long words are swapped starting at 40 byte transfer size and greater.
device memory description:
static ddi_device_acc_attr_t sdram_access_attr =
DDI_DEVICE_ATTR_V0, /* Boilerplate value */
DDI_STRUCTURE_LE_ACC,
DDI_STRICTORDER_ACC /* Don't reorder accesses */
The user application does a read call, which goes to xxread. xxread calls physio( xxstrategy, bp, dev, B_READ, xxminphys, uio );
In xxstrategy the transfer is done using
ddi_mem_rep_get8(ucb->ucb_sdram_accHndl,
(uint8_t*) kaddr,
(uint8_t*) raddr,
(size_t) bp->b_resid),
(uint_t) DDI_DEV_AUTOINCR );
PCI Device memory is loaded with incrementing address (8bit), 0,1,2... This is confirmed using a PCI Bus Analyzer.
A read of 36 bytes or less returns:
03 02 01 00 07 06 05 04 ...
A read of 40 bytes returns:
07 06 05 04 03 02 01 00 ...
If I peek 1 byte at a time using ddi_get8(ucb->ucb_sdram_accHndl, ...) I get
00 01 02 03 04 05 06 07
Why are the long words swapped starting at 40 byte transfer size and greater?

Transfering music from playlist to card writer for SD card for Samsung A720

I have put songs in playlist and plugged in USB 2 card writer with SD card for phone. How do I transfer the playlist to card. The reader doesn't even show up on screen when plugged in? help me I am lost after 50 pages of looking for similar question on discussion board and finding only one, with no answer. Who can help.

Select the songs in iTunes and drag them from iTunes to the card on the desktop.
It won't show up in iTunes.

Could not write on SD card after upgradation

After upgrading my HP slate7 to KitKat version, I could not write on SD card. What is the solution for this????

Perhaps this article can help explain how Google changed Android KitKat 4.4:
KitKat and SD cards — what's fixed, what's broken and what's misunderstood.
WyreNut
I am a Volunteer here, not employed by HP.
You too can become an HP Expert! Details HERE!
If my post has helped you, click the Kudos Thumbs up!
If it solved your issue, Click the "Accept as Solution" button so others can benefit from the question you asked!

How can we delete wild card entry from table

how can we delete wild card entry from table
i want adjust the seeting for order type print out form
like in 0id2 i have specified ordertupe nad print form in pm module
but in oid3 fro palnner group if i make star it is not taking specific defiend field

Hi....
Follow these steps....
1. Goto se16 and enter ur table name.. press F7 you can get selection screen now press F8...
2. Click one perticuler record that u want to delete.. and press Change icon in App'toll bar...
3. enter ?H at command field and again press enter...
4. switch into classical debugger...
5. write CODE at field ... it will gives EDIT as value...
6. Change that EDIT into SHOW and press pencel icon just beside the SHOW...
7. Now press F8...
8. you can get delete option over there...
Thanks,
Naveen.I

How to write firmware to ipw2200 serials wireless adaptor?

I have some ipw2200 cards with very low version of firmware, and I'v installed firmware card to my computer.
How to write firmware to the EEPROM of the cards?

Thank you for your patient
With such a low version of fw, the card cannot work in windows.
And I can't dectect the device in wpa_gui. But I can see eth1 by iwconfig, it says the radio is off.

How to write an on card installer

Similar Messages

Maybe you are looking for