HP Deskjet 3055A Unable to connect on wireless

I cannot set up my deskjt 3055A on wireless. The blue light on the printer is flashing and the printer screen states wireless on.But printer cannot see the router

There is a document with steps to install this series printer on a wireless network. This document can be found here.
Also, if the printer cannot see the router (SSID), then it is possible the network is using hidden broadcast. Make sure the SSID is being broadcast so that the printer can find the network.
Also, have you tried power cycling the network system?
* Unplug router, wait 20 seconds, and plug back in
* After router has restarted, then restart the PC
* While PC is restarting, power cycle the printer
Let me know how it goes.
-------------How do I give Kudos? | How do I mark a post as Solved? --------------------------------------------------------
I am not an HP employee.

Similar Messages

HP Officejet Pro 8000 Wireless: HP printer unable to connect to wireless router.

Installing new printer, getting error msg saying HP printer unable to connect to wireless router. MAC address filtering may be enabled on your wireless router which can prevent HP printer from connecting to your wireless network during setup.
SOLUTION says: If MAC address filtering is enabled and you would like to keep it enabled, you must add the MAC addressof your printer to the list of permitted devices for your wireless router before continuing.
My router is WD My Net N900 Router. MAC filtering is diabled. My security mode is WPA/WPA2 Personal.
I have run out of ideas to try and fix the issues, would appreciate some help.
Thanks,

Hi Jamshidk
I am surprised you are getting that message and you checked the router settings and it is showing that the Mac Filtering is disabled.
I would suggest connecting the printer to the router with a ethernet cable to get a valid IP address and then setup the wireless.
Print a configuration report.
http://h10025.www1.hp.com/ewfrf/wc/document?cc=us&dlc=en&docname=c01554589&lc=en&product=3760410&tmp...
Type the IP address from the configuration page in the address bar into internet explorer browser. This will open the embedded web server for the printer. Click on the Networking tab, on the left hand side select wireless. After this is setup and applied, disconnect the ethernet cable.
Should be on the wireless network. Takes about 1 minute.
Run the add printer wizard.
Go to start, devices and printers and select add a printer. (Win 7)
Test the printer.
If you need more assistance just let me know.
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
Gemini02
I work on behalf of HP

HP Deskjet 3050 - Unable to connect to WPA secured wireless network

Hello,
My first post here so please excuse any faux pas on my part. I bought this HP Deskjet 3050 a week ago and have been waging war with it ever since. I'd be really grateful if someone could possibly advise on how I can resolve this.
I am unable to connect the printer to my secured wireless network, even though other computers, cell phones, etc. are connected without issue. I have tried WPA, WPA2 and WPA2-Mixed security modes with the same failure. Specifically, the connection wizard reaches 66% and then displays the error that the wizard is unable to find network/printer. If I disable the security, the printer connects fine.
I'm using a Linksys WRVS4400N router with firewall and associated firewall settings disabled. The router is broadcasting on 802.11G/N mixed mode.
I'm installing the software supplied on the setup CD on a Windows XP SP3 system. I have confirmed that the network the PC and printer are connected to are the same.
A question as well, if I may: I haven't tried these drivers yet but I see there are updated drivers for the printer dated 14/12/2010. The release notes indicate improved networking, but don't elaborate beyond this. Does anyone know if there was a known problem with connecting to secured networks that has now been fixed?
Finally, just a note that I'm partially sighted and am using a screen reader on all systems. I'll try my best to be as helpful as I can but please do excuse me if I occasionally can't find settings, etc. on screen and need a bit more detailed help.
Thanks in advance for your help, which I really will appreciated.
Have a pleasant day,
All the best for now and take care,
Hussein.
It's not the fact it can't be done, it's the fact it hasn't been done, yet.
This question was solved.
View Solution.

HI,
firstly, apologies for the delay getting back to you. Poor health has meant I've had little time nor inclination to do much on the computer side of htings.
Anyway, I'm please to say the problem with the HP 3050 failing to connect to my network is now solved. It seems to be a bug with the setup software, and that seems to include the latest version posted Dec 2010.
To resolve the problem, I did the following:
1. Disable all security options for the network, so it's just an open network.
2. Connect the HP 3050 to the network using the setup wizard. This time it connected OK for me.
3. Locate the printer's IP address. I used the client list table accessed through my router's interface. You may be able to get this through the printer's on-screen menu, but as I'm partially sighted, this wasn't an option for me.
4. Log into the printer's control panel at http://ip.address.of.printer e.g. http://192.168.2.108
5. Under the advanced options, configure the settings for the network, including security protocol and passphrase. Remember to enter the SSID of the network exactly as configured on the router.
6. Apply the settings and log out of the printer's control panel.
7. Log back into the router's control panel and re-apply the security options. Be sure that they match those match those entered for the printer.
Hopefully this will be of use to others in the same position.
Thanks again for your time.
Best,
H.
It's not the fact it can't be done, it's the fact it hasn't been done, yet.

HP Deskjet 3055A does not connect to WIFI with security

I am trying to configure a Deskjet 3055A on my DD-WRT router. I am a highly skilled networking engineer so I know 100% what I am doing.
Firstly, DD-WRT does not support WPS conenction, because these are highly insecure. This means my only method of connecting the pritner to my home network is to connect it to my PC and use the installation utility (dowloaded from your drivers page) I am using version 28.8.
My router supports both 2.4 and 5GHz and I know the printer is only 2.4GHz. I completely disabled the 5GHz network for the purpose of connecting the printer even though it should not have any effect.
I have also rebooted my router, and reset the printers wireless network using its in-built control panel.
Anyway, after a shameful 2 hours troubleshooting, I managed to find out that the printer WILL NOT CONNECT to the WIFI network if any security is applied against it. It works 100% fine with open security however, this is completely unnacceptable.
I have tried both WPA Personal and also WPA2 Personal, both with the same effect.
For the sake of trying, I also added the printer to my open WIFI network and tried to manually edit the WIFI setting through the printers web interface however, whenever I try and access the Wireless setup wizard, I simply get an error saying "Internal System Error" - eventually I managed to get around this other bug that has been there for years (see http://h30434.www3.hp.com/t5/Printer-Networking-and-Wireless/Internal-System-Error-prevents-access-t...
After going through the printers web interface WIFI setup, the issue is still the same and it will not connect.
HP, we were about to order 2500 of these printers for our remote site users. If you do not come up with a quick solution/bug fix, consider the business lost!
Regards
Ian
This question was solved.
View Solution.

After much playing I managed to find a fix for this!
For all users who are unable to find a fix using the other methods, here's what to do.
Change your local network to open security but note down your WIFI setting for your typical setup.
Connect the printer to the open network using the HP software (using a USB cable)
Go to the printer's URL, but ensure you connect using HTTPS - if you get an internal system error, keep refreshing until it works (WHAT A JOKE!!!!)
Click on "Network" on the top, then click on "Advanced" on the left.
Enter the network settings as they should be when secured.
At the bottom, tick "In an infrastructure network, use 802.11b/g behaviour(assuming your netwoek supports g, otherwise use the b only option), then click apply.
Turn your wireless security back on, on your router and then the printer should connect!
I really am baffled as to why this isn't automatically enabled, if the printer doesn't work with wireless security on a Wireless N network, then have this as the default!
HP - feel free to thank me in this post!

Unable to connect via wireless, printer is online.

I am using a Photosmart plus 209a via wireless. There are 3 notebooks connected. 2 will print but my Dell Studio (Win 7 Pro) will not. It was previously connected but now unable to connect. I have uninstalled all components using level 3 twice. Have used the Print/Scan tool. Downloaded the full SW package and the Basic driver SW. I process a job and it gets to the spooler and then "print job failed". I can view the control panel via IP address. I can view network settings and print wireless test page through HP Solution Center. Why am I unable to connect? I was able to use via USB but this is not an option.

It sounds like there is something different on the Dell Studio since it works from two other computers on the same network as the Dell Studio. It also sounds like you are able to access the EWS of the printer by using its IP address.
Are there any other errors messages regarding the printer? If so, what are they?
Is there a third party firewall installed (e.g. Norton, Kasperksy, BitDefender, etc.)?
Is this Windows 7 Professional 32bit or 64bit?
↙-----------How do I give Kudos?| How do I mark a post as Solved? ----------------↓

IPod Touch unable to connect to wireless network.

I just got an iPod Touch 4 for my birthday (w00t), however I cannot seem to get it to connect to my wireless router. Everytime I try, it says Unable to connect to network. I reset the routers password, but it didn't do anything. I saw in other threads people said to switch ti WPA security, but mine is already set as WPA Personal. I'm not sure what to do! Please help!

NO I did not and thank you very much for the advice. My problem was stated incorrectly in that while I am able to connect to the wireless from that point on I am unable to connect to the internet. I will check the article referred to.

Suddenly unable to connect to wireless network...exhausted all fixes

I’ve got an odd problem with my two-week old MacBook Pro and its connection to my wireless network. I’ve done what I think is pretty exhaustive troubleshooting, but remain baffled. Here’s the story.
This morning I connected to my wireless network (DSL 2WIRE modem/router) with no problem. This afternoon I returned and Airport refused to connect, giving me the error message, “Airport is unable to connect to the wireless network…” The network shows up as being available, but when I attempt to connect, it wont. (I didn’t make any changes or install any programs this morning).
Here’s what I’ve done:
[1] Restarted the router
[2] Repaired permissions
[3] Deleted the network’s entry in Keychain Access
[4] Re-entered my WEP code (assuring it is in correctly; I’ve tried both with the “$” and without)
[5] Used interface robustness and without.
[6] Attempted to join the network from the System Preferences>Network.Airport route.
[7] Created a new account and tried connecting.
Other tidbits of information:
[1] Another MacBook in the house connects to the network with no problem.
[2] My MacBook can connect to another (unsecured) network that I can “see” in my house.
So, it would seem my Airport card is working okay.
Any ideas??

Some more info (in case anyone is listening...)
I tried turning off the WEP code and could connect. (Since I share files on my home network, this isn't a "solution").
I also tried Resetting the MacBook Pro System Management Controller (SMC)(See: http://docs.info.apple.com/article.html?artnum=303319). I did this (I think -- there wasn't any indication that the reset "took"), but alas -- no luck.
I gave Apple Care a call, but the support guy, while courteous and all, didn't have anything to offer other than telling me to take it in to an Apple Store for a repair (clearly it isn't a hardware issue).
Heeellllppppp!

Unable to connect to wireless network

I am unable to connect to my wireless network with my MacBook.
I have no trouble connecting with my windows PC. I have double checked the WEP key and checked that I am using the correct key type (128 bit hex). There is no MAC address access control on the network and DHCP is available.
All I get is a message saying 'There was an error joining the AirPort network "network-name"' and two buttons: 'Try again' (which produces the same error) and 'OK'.
Can anyone help?
MacBook Pro 15" 2.16GHz Mac OS X (10.4.9)

Hi,
I'm also having this problem of not being able to connect to a wireless network. However, I'm in Spain and have my MacBook. I was able to connect to the wireless network with no problem for about 5 days' and then access stopped. I get the same password edit saying the network does not recognise the pw. I've tried all the proposed solutions described in this thread: entering the data manually, using a $ or " sign and to no avail.
The airport symbol is grayed out. However, when I open internet connection to join the network, 15 other networks including my own show up, so I believe the airport card is working okay. (everyone seems to have WiFi in the area).
Does anyone know if there is something peculiar to Europe I need to do in order to gain wireless access again ? I know the broadcast chanels are 1-13 vs 1-11 in the US. But I don't think this is a problem since I had access for a time.
Any info welcome. Sorry if I'm threadjacking here but I don't see where to start a new topic. The network is fine as I'm connecting using an ethernet cable.
Thanks in advance,
J.
iMac G5 Rev 2; 20; 2GHz; 250 GB; 1.512 RAM; & MacBook 2GHz Intel dual core Mac OS X (10.4.2)

Unable to connect to wireless network after software update

on updating the software on my Ipad 3 I am unable to connect to my office wireless network

Look at iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
iPad: Issues connecting to Wi-Fi networks http://support.apple.com/kb/ts3304
iOS: Recommended settings for Wi-Fi routers and access points http://support.apple.com/kb/HT4199
Additional things to try.
Try this first. Turn Off your iPad. Then turn Off (disconnect power cord for 30 seconds or longer) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
Change the channel on your wireless router (Auto or Channel 6 is best). Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
Another thing to try - Go into your router security settings and change from WEP to WPA with AES.
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
If none of the above suggestions work, look at this link.
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
Fix iPad Wifi Connection and Signal Issues http://www.youtube.com/watch?v=uwWtIG5jUxE
Fix Slow WiFi Issue https://discussions.apple.com/thread/2398063?start=60&tstart=0
Unable to Connect After iOS Update - saw this solution on another post.
https://discussions.apple.com/thread/4010130
Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
~~~~~~~~~~~~~~~
If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
 Cheers, Tom

Iphone 4 IOS5 unable to connect to wireless network.

I am unable to connect my iphone4 IOS5 to wireless network at home. It was working fine before upgrade the IOS.

Most routers have this problem; the DHCP daemon that assigns IP addresses quits for some reason, so devices that already have an IP address continue to work (until their lease time expires) but new devices don't get an IP address and thus cannot connect.

WRT54GC : unable to connect to wireless network

I have a WRT54GC ver 1 router and I am unable to connect to my wireless network. The problem is I dont see my wireless netwrok in the "list of available networks". I see all my neighbour's networks, but not mine.
I have upgraded the firmware to v1.05.7 and that hasnt helped either. I am able to connect to the internet through the ethernet though.
Multiple chat sessions with linksys customer service havent helped. Has anybody faced such an issue before?

Reset the router for 20-30 seconds ........ while holding the reset unplug the power cable of router ....... wait for 10 seconds ........ plug back the power cable & release the reset ........
See if it shows your home network or not ......

Hp photosmart 5520 unable to connect to wireless router

The printer worked fine-I went on vacation and now it won't work. I ran the wireless network test and it said"hp printer is unable to connect to your wireless router". The wireless router is connected and running fine. My wireless hp computer (windows 7) works just fine.
The report satd "network name ssid found" said FAILED
But "current configuration" showed the SSID
can anyone offer a fix?
Help
colleenmercy
This question was solved.
View Solution.

Hi colleenmercy,
On the network menu, select Restore Network Defaults. This will clear the current network settings and allow you to reconnect the printer to the network. You can use the wireless setup wizard or reinstall the HP software to reconnect.
I was an HP employee.
Please mark the post that solves your problem as "Accepted Solution"

Photosmart 6510 unable to connect to wireless network.

The wireless icon on my printer indicated "Not Connected" and showed this information
IP Address: No Link
Network Name: N/A
MAC: A0:B3:CC:12:3A:07
When running the Wireless Setup Wizard and selecting the internet network my computer is currently connected to, it then said that it was "Unable to connect to network. Unsupported authentication or encryption type." I ran a wireless network test and next to "Network Name (SSID) Found" is says "FAIL". If you need more information that can be found on the netork test results I will be happy to give you them. I do not have access to the router as I am currently at my university. It is a secured network so I'm thinking this is where the problem is coming from. Also, whenever I try to type in my IP address into my URL bar the page is not found. Any suggestions? Or am I just going to have to purchase a USB cable?

Here's other information from my Wireless Network Test Results.
Wireless:
-Wireless On- Pass
-Wireless Working- Pass
-Signal Quality- Not Run
Connectivity:
-Connected- Not Run
-Disconnect count total- 0
-Disconnect count (last hour)- 0
-Disconnect count (last 24 hours)- 0
Network:
-Network Name (SSID) Found- FAIL (All this was in bold)
-Other networks detected matching your network name (SSID)- Not Run
-Wireless Networks Detected- 10
Settings:
-Printer Settings Consistent with Wireless Router Settings- Not Run
-No Filtering- Not Run
-Channel- Not Run
-Security- Not Run
Current Configuration:
-Network Name (SSID)- Not Set
-Hardware Address (MAC)- a0:b3:cc:12:3a:07
-IP Address- Not applicable
-Configuration Source- Not applicable
-Communication Mode- Infrastructure
-Authentication Type- Open System
-Encryption- None

Mac Mini unable to connect to wireless

Hello there,
I have a 1.66ghz Mac Mini with OSX 10.4.11
I am trying to connect to my wireless router but am having some difficulty. The Airport can see my router in the menu, and when I enter the password, it processes for about 30 seconds then says "There was an error joining the AirPort network".
I know the connection works, because I am using it right now on my macbook with Leopard 10.5.6.
I am using a Netgear wireless router model no. WGT624
Apparently the connection works when I connect via ethernet.
Any help would be much appreciated.

There is no need to upgrade to MacOS 10.5 to resolve this - MacOS 10.4.x was perfectly capable of connecting to wireless routers, and there are untold numbers of Macs running various versions of Tiger which are used daily on wifi.
Most issues with connection failures of this sort are caused by issues with security. As such, a good place to start is to temporarily disable your router's wifi security so that it is an open network, and then try and connect with the mini. If it fails then, you know it's an issue with the mini and signal quality because your MacBook connects OK (thus the router is working correctly). In that case you could obtain a copy of AP Grapher (http://www.chimoosoft.com/products/apgrapher/) on the mini (after connecting it via ethernet which you say works) and looking at the wifi signal the mini is seeing - it seems likely at that point you'll find the signal is low, or rather variable, or the trace for noise is high, meaning there is significant interference. This can create a situation where the system can 'see' the router via wifi, but fails to connect due to time out errors.
If it the mini connects with the security off, then the issue is the type of security or perhaps that the password is not being entered correctly.

Wicd connects to Wired fine but is unable to connect to wireless

I don't think I have changed anything, but now wicd will not connect to any wireless network (Stuck at optaining IP address, or Verifying association if I use static ip, and then, without saying a specific error, quits connecting and goes back to not connected.)
Latest update:
[2012-06-30 11:22] Running 'pacman -Syyu'
[2012-06-30 11:22] synchronizing package lists
[2012-06-30 11:22] starting full system upgrade
[2012-06-30 11:25] upgraded audacity (2.0.0-1 -> 2.0.1-1)
[2012-06-30 11:25] upgraded ca-certificates-java (20120524-1 -> 20120608-1)
[2012-06-30 11:25] upgraded libsystemd (185-2 -> 185-4)
[2012-06-30 11:25] upgraded systemd-tools (185-2 -> 185-4)
[2012-06-30 11:25] upgraded dbus-core (1.6.0-4 -> 1.6.0-5)
[2012-06-30 11:25] upgraded dbus-glib (0.98-1 -> 0.100-1)
[2012-06-30 11:25] upgraded chromium (19.0.1084.56-1 -> 20.0.1132.47-1)
[2012-06-30 11:25] upgraded cryptsetup (1.4.2-2 -> 1.4.3-1)
[2012-06-30 11:25] upgraded docbook-xsl (1.77.0-1 -> 1.77.1-2)
[2012-06-30 11:25] upgraded git (1.7.11-1 -> 1.7.11.1-1)
[2012-06-30 11:25] upgraded hyphen (2.8.3-1 -> 2.8.4-1)
[2012-06-30 11:25] upgraded imagemagick (6.7.7.7-1 -> 6.7.7.10-1)
[2012-06-30 11:25] upgraded sysvinit (2.88-3 -> 2.88-6)
[2012-06-30 11:25] upgraded initscripts (2012.06.1-1 -> 2012.06.2-1)
[2012-06-30 11:25] upgraded poppler (0.20.0-1 -> 0.20.1-1)
[2012-06-30 11:25] upgraded poppler-glib (0.20.0-1 -> 0.20.1-1)
[2012-06-30 11:25] upgraded inkscape (0.48.3.1-3 -> 0.48.3.1-4)
[2012-06-30 11:25] >> Traceroute is now provided by core/traceroute
[2012-06-30 11:25] upgraded iputils (20101006-2 -> 20101006-3)
[2012-06-30 11:25] upgraded keyutils (1.5.5-2 -> 1.5.5-3)
[2012-06-30 11:25] upgraded lib32-dbus-core (1.4.20-1 -> 1.6.0-1)
[2012-06-30 11:25] upgraded lib32-libtiff (4.0.1-1 -> 4.0.2-1)
[2012-06-30 11:25] upgraded libnl (3.2.9-1 -> 3.2.11-1)
[2012-06-30 11:25] upgraded libusbx (1.0.12-1 -> 1.0.12-2)
[2012-06-30 11:25] upgraded libpcap (1.2.1-2 -> 1.3.0-1)
[2012-06-30 11:25] upgraded libreoffice-en-US (3.5.4-1 -> 3.5.4-2)
[2012-06-30 11:26] upgraded libreoffice-common (3.5.4-1 -> 3.5.4-2)
[2012-06-30 11:26] upgraded libreoffice-base (3.5.4-1 -> 3.5.4-2)
[2012-06-30 11:26] upgraded libreoffice-calc (3.5.4-1 -> 3.5.4-2)
[2012-06-30 11:26] upgraded libreoffice-draw (3.5.4-1 -> 3.5.4-2)
[2012-06-30 11:26] upgraded libreoffice-gnome (3.5.4-1 -> 3.5.4-2)
[2012-06-30 11:26] upgraded libreoffice-impress (3.5.4-1 -> 3.5.4-2)
[2012-06-30 11:26] upgraded libreoffice-kde4 (3.5.4-1 -> 3.5.4-2)
[2012-06-30 11:26] upgraded libreoffice-math (3.5.4-1 -> 3.5.4-2)
[2012-06-30 11:26] upgraded libreoffice-postgresql-connector (3.5.4-1 -> 3.5.4-2)
[2012-06-30 11:26] upgraded libreoffice-sdk (3.5.4-1 -> 3.5.4-2)
[2012-06-30 11:26] upgraded libreoffice-sdk-doc (3.5.4-1 -> 3.5.4-2)
[2012-06-30 11:26] upgraded libreoffice-writer (3.5.4-1 -> 3.5.4-2)
[2012-06-30 11:26] upgraded libwbclient (3.6.5-3 -> 3.6.6-1)
[2012-06-30 11:26] upgraded linux-firmware (20120227-2 -> 20120625-1)
[2012-06-30 11:26] warning: /etc/pacman.d/mirrorlist installed as /etc/pacman.d/mirrorlist.pacnew
[2012-06-30 11:26] upgraded pacman-mirrorlist (20120211-1 -> 20120626-1)
[2012-06-30 11:26] upgraded pciutils (3.1.9-2 -> 3.1.10-1)
[2012-06-30 11:26] upgraded pixman (0.26.0-1 -> 0.26.2-1)
[2012-06-30 11:26] upgraded psmisc (22.18-2 -> 22.19-1)
[2012-06-30 11:26] upgraded python-dbus-common (1.1.0-2 -> 1.1.1-1)
[2012-06-30 11:26] upgraded python2-dbus (1.1.0-2 -> 1.1.1-1)
[2012-06-30 11:26] upgraded qt (4.8.2-1 -> 4.8.2-2)
[2012-06-30 11:26] upgraded raptor (2.0.7-2 -> 2.0.8-1)
[2012-06-30 11:26] upgraded smbclient (3.6.5-3 -> 3.6.6-1)
[2012-06-30 11:26] upgraded vlc (2.0.1-2 -> 2.0.2-1)
[2012-06-30 11:33] Running 'pacman -U android-sdk-r20-2-x86_64.pkg.tar.xz'
[2012-06-30 11:34] You need to source /etc/profile or relogin to add the Android SDK tools to your path.
[2012-06-30 11:34] The android group has been removed, install android packages as root.
[2012-06-30 11:34] upgraded android-sdk (r18-1 -> r20-2)
[2012-06-30 11:35] Running 'pacman -U android-sdk-platform-tools-r12-1-any.pkg.tar.xz'
[2012-06-30 11:36] upgraded android-sdk-platform-tools (r11-2 -> r12-1)
[2012-06-30 11:36] Running 'pacman -U eclipse-android-20.0.0-1-any.pkg.tar.xz'
[2012-06-30 11:36] upgraded eclipse-android (18.0.0-2 -> 20.0.0-1)
[2012-06-30 11:37] Running 'pacman -U eclipse-emf-2.8.0-1-any.pkg.tar.xz'
[2012-06-30 11:38] upgraded eclipse-emf (2.7.2-2 -> 2.8.0-1)
[2012-06-30 11:38] Running 'pacman -U eclipse-gef-3.8.0-1-any.pkg.tar.xz'
[2012-06-30 11:40] upgraded eclipse-gef (3.7.2-2 -> 3.8.0-1)
[2012-06-30 11:41] Running 'pacman -U pgl-2.2.1-2-x86_64.pkg.tar.xz'
[2012-06-30 11:41] warning: directory permissions differ on tmp/
filesystem: 1777 package: 755
[2012-06-30 11:41] upgraded pgl (2.2.1-1 -> 2.2.1-2)
RC.conf
# NETWORKING
# HOSTNAME: Hostname of machine. Should also be put in /etc/hosts
HOSTNAME="moulder"
# Use 'ip addr' or 'ls /sys/class/net/' to see all available interfaces.
# Wired network setup
# - interface: name of device (required)
# - address: IP address (leave blank for DHCP)
# - netmask: subnet mask (ignored for DHCP) (optional, defaults to 255.255.255.0)
# - broadcast: broadcast address (ignored for DHCP) (optional)
# - gateway: default route (ignored for DHCP)
# Static IP example
# interface=eth0
# address=192.168.0.2
# netmask=255.255.255.0
# broadcast=192.168.0.255
# gateway=192.168.0.1
# DHCP example
# interface=eth0
# address=
# netmask=
# gateway=
interface=eth0
address=
netmask=
broadcast=
gateway=
# Setting this to "yes" will skip network shutdown.
# This is required if your root device is on NFS.
NETWORK_PERSIST="no"
# Enable these netcfg profiles at boot-up. These are useful if you happen to
# need more advanced network features than the simple network service
# supports, such as multiple network configurations (ie, laptop users)
# - set to 'menu' to present a menu during boot-up (dialog package required)
# - prefix an entry with a ! to disable it
# Network profiles are found in /etc/network.d
# This requires the netcfg package
#NETWORKS=(main)
# DAEMONS
# Daemons to start at boot-up (in this order)
# - prefix a daemon with a ! to disable it
# - prefix a daemon with a @ to start it up in the background
# If something other takes care of your hardware clock (ntpd, dual-boot...)
# you should disable 'hwclock' here.
DAEMONS=(hwclock syslog-ng !network !networkmanager netfs crond dbus !dhcpcd wicd alsa acpid pgl laptop-mode slim)
when trying # dhcpcd wlan0 (Although I use dhclient in wicd)
dhcpcd[2066]: version 5.5.6 starting
dhcpcd[2066]: wlan0: waiting for carrier
dhcpcd[2066]: timed out
iwconfig
eth0 no wireless extensions.
lo no wireless extensions.
wlan0 IEEE 802.11bgn ESSID:"cannedyams"
Mode:Managed Frequency:2.412 GHz Access Point: Not-Associated
Tx-Power=15 dBm
Retry long limit:7 RTS thr:off Fragment thr:off
Power Management:off
wicd log when connecting by wire
2012/06/30 16:28:56 :: Internet Systems Consortium DHCP Client 4.2.3-P2
2012/06/30 16:28:56 :: Copyright 2004-2012 Internet Systems Consortium.
2012/06/30 16:28:56 :: All rights reserved.
2012/06/30 16:28:56 :: For info, please visit https://www.isc.org/software/dhcp/
2012/06/30 16:28:56 ::
2012/06/30 16:28:57 :: Listening on LPF/eth0/b8:70:f4:83:a4:3b
2012/06/30 16:28:57 :: Sending on LPF/eth0/b8:70:f4:83:a4:3b
2012/06/30 16:28:57 :: Sending on Socket/fallback
2012/06/30 16:28:57 :: DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 5
2012/06/30 16:28:58 :: DHCPREQUEST on eth0 to 255.255.255.255 port 67
2012/06/30 16:28:58 :: DHCPOFFER from 10.0.1.1
2012/06/30 16:28:58 :: DHCPACK from 10.0.1.1
2012/06/30 16:28:58 :: bound to 10.0.1.13 -- renewal in 5654 seconds.
2012/06/30 16:28:58 :: DHCP connection successful
2012/06/30 16:28:58 :: Connecting thread exiting.
2012/06/30 16:28:59 :: Sending connection attempt result success
when wirelessly
2012/06/30 16:25:19 :: Internet Systems Consortium DHCP Client 4.2.3-P2
2012/06/30 16:25:19 :: Copyright 2004-2012 Internet Systems Consortium.
2012/06/30 16:25:19 :: All rights reserved.
2012/06/30 16:25:19 :: For info, please visit https://www.isc.org/software/dhcp/
2012/06/30 16:25:19 ::
2012/06/30 16:25:20 :: Listening on LPF/wlan0/bc:77:37:07:fd:96
2012/06/30 16:25:20 :: Sending on LPF/wlan0/bc:77:37:07:fd:96
2012/06/30 16:25:20 :: Sending on Socket/fallback
2012/06/30 16:25:20 :: DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 6
2012/06/30 16:25:26 :: DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 12
2012/06/30 16:25:38 :: DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 15
2012/06/30 16:25:53 :: DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 14
2012/06/30 16:26:07 :: DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 14
2012/06/30 16:26:21 :: No DHCPOFFERS received.
2012/06/30 16:26:21 :: No working leases in persistent database - sleeping.
2012/06/30 16:26:21 :: DHCP connection failed
2012/06/30 16:26:21 :: exiting connection thread
2012/06/30 16:26:26 :: Sending connection attempt result dhcp_failed
lspci
08:00.0 Network controller: Intel Corporation Centrino Wireless-N 1030 (rev 34)
I've already switched to dclient and turned power saving features off
Any Ideas?
Last edited by parkermcg (2012-06-30 21:41:14)

messages.log when connecting to wireless
Jun 30 17:21:42 localhost dhclient: Internet Systems Consortium DHCP Client 4.2.3-P2
Jun 30 17:21:42 localhost dhclient: Copyright 2004-2012 Internet Systems Consortium.
Jun 30 17:21:42 localhost dhclient: All rights reserved.
Jun 30 17:21:42 localhost dhclient: For info, please visit https://www.isc.org/software/dhcp/
Jun 30 17:21:42 localhost dhclient:
Jun 30 17:21:42 localhost dhclient: Listening on LPF/wlan0/bc:77:37:07:fd:96
Jun 30 17:21:42 localhost dhclient: Sending on LPF/wlan0/bc:77:37:07:fd:96
Jun 30 17:21:42 localhost dhclient: Sending on Socket/fallback
Jun 30 17:21:42 localhost dhclient: DHCPRELEASE on wlan0 to 10.0.1.1 port 67
Jun 30 17:21:42 localhost kernel: [ 624.129671] iwlwifi 0000:08:00.0: L1 Enabled; Disabling L0S
Jun 30 17:21:42 localhost kernel: [ 624.136425] iwlwifi 0000:08:00.0: Radio type=0x2-0x2-0x1
Jun 30 17:21:43 localhost kernel: [ 624.290321] ADDRCONF(NETDEV_UP): wlan0: link is not ready
Jun 30 17:21:43 localhost kernel: [ 624.355364] iwlwifi 0000:08:00.0: L1 Enabled; Disabling L0S
Jun 30 17:21:43 localhost kernel: [ 624.362119] iwlwifi 0000:08:00.0: Radio type=0x2-0x2-0x1
Jun 30 17:21:43 localhost kernel: [ 624.500638] ADDRCONF(NETDEV_UP): wlan0: link is not ready
Jun 30 17:21:43 localhost dhclient: Internet Systems Consortium DHCP Client 4.2.3-P2
Jun 30 17:21:43 localhost dhclient: Copyright 2004-2012 Internet Systems Consortium.
Jun 30 17:21:43 localhost dhclient: All rights reserved.
Jun 30 17:21:43 localhost dhclient: For info, please visit https://www.isc.org/software/dhcp/
Jun 30 17:21:43 localhost dhclient:
Jun 30 17:21:43 localhost dhclient: Listening on LPF/eth0/b8:70:f4:83:a4:3b
Jun 30 17:21:43 localhost dhclient: Sending on LPF/eth0/b8:70:f4:83:a4:3b
Jun 30 17:21:43 localhost dhclient: Sending on Socket/fallback
Jun 30 17:21:43 localhost dhclient: DHCPRELEASE on eth0 to 10.0.1.1 port 67
Jun 30 17:21:43 localhost kernel: [ 624.875063] r8169 0000:07:00.0: eth0: link down
Jun 30 17:21:43 localhost kernel: [ 624.876536] ADDRCONF(NETDEV_UP): eth0: link is not ready
Jun 30 17:21:43 localhost kernel: [ 625.050344] r8169 0000:07:00.0: eth0: link down
Jun 30 17:21:43 localhost kernel: [ 625.050842] ADDRCONF(NETDEV_UP): eth0: link is not ready
Jun 30 17:21:43 localhost dhclient: Internet Systems Consortium DHCP Client 4.2.3-P2
Jun 30 17:21:43 localhost dhclient: Copyright 2004-2012 Internet Systems Consortium.
Jun 30 17:21:43 localhost dhclient: All rights reserved.
Jun 30 17:21:43 localhost dhclient: For info, please visit https://www.isc.org/software/dhcp/
Jun 30 17:21:43 localhost dhclient:
Jun 30 17:21:43 localhost dhclient: Listening on LPF/wlan0/bc:77:37:07:fd:96
Jun 30 17:21:43 localhost dhclient: Sending on LPF/wlan0/bc:77:37:07:fd:96
Jun 30 17:21:43 localhost dhclient: Sending on Socket/fallback
Jun 30 17:21:44 localhost dhclient: DHCPRELEASE on wlan0 to 10.0.1.1 port 67
Jun 30 17:21:44 localhost kernel: [ 625.278255] iwlwifi 0000:08:00.0: L1 Enabled; Disabling L0S
Jun 30 17:21:44 localhost kernel: [ 625.285000] iwlwifi 0000:08:00.0: Radio type=0x2-0x2-0x1
Jun 30 17:21:44 localhost kernel: [ 625.441983] ADDRCONF(NETDEV_UP): wlan0: link is not ready
Jun 30 17:21:44 localhost kernel: [ 625.512578] iwlwifi 0000:08:00.0: L1 Enabled; Disabling L0S
Jun 30 17:21:44 localhost kernel: [ 625.519296] iwlwifi 0000:08:00.0: Radio type=0x2-0x2-0x1
Jun 30 17:21:44 localhost kernel: [ 625.672665] ADDRCONF(NETDEV_UP): wlan0: link is not ready
Jun 30 17:21:46 localhost dhclient: Internet Systems Consortium DHCP Client 4.2.3-P2
Jun 30 17:21:46 localhost dhclient: Copyright 2004-2012 Internet Systems Consortium.
Jun 30 17:21:46 localhost dhclient: All rights reserved.
Jun 30 17:21:46 localhost dhclient: For info, please visit https://www.isc.org/software/dhcp/
Jun 30 17:21:46 localhost dhclient:
Jun 30 17:21:47 localhost dhclient: Listening on LPF/wlan0/bc:77:37:07:fd:96
Jun 30 17:21:47 localhost dhclient: Sending on LPF/wlan0/bc:77:37:07:fd:96
Jun 30 17:21:47 localhost dhclient: Sending on Socket/fallback
Jun 30 17:21:47 localhost dhclient: DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 8
Jun 30 17:21:55 localhost dhclient: DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 12
Jun 30 17:22:07 localhost dhclient: DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 12
Jun 30 17:22:19 localhost dhclient: DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 19
Jun 30 17:22:38 localhost dhclient: DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 10
Jun 30 17:22:48 localhost dhclient: No DHCPOFFERS received.
Jun 30 17:22:48 localhost dhclient: No working leases in persistent database - sleeping.

HP Deskjet 3055A Unable to connect on wireless

Similar Messages

Maybe you are looking for