HP Laserjet M2727nf - Firmware not loading to Printer

My printer display was not working so I ordered a new one.  But as I read some postings it seems to be by formatter board.  I baked the formatter board.  After I baked it, the display would show: Hewitt Packard >>>>>.  I did the below
but the firmware utility update is not going to the printer.  The display shows ***BootDimm*** Ready 2 download.
I have left the jumper on and have taken it off to upload the firmware to the printer.  Nothing has happened.   I have not even seen the display changing to erasing firmware, then programing firmware.
I baked the board and it started to work.  I then Download the firmware utility update for my printer.  I Removed the printer left cover. Turned the printer on while it’s was connected by usb. Jumper or short the 2 pin connector - the display read "ready to load firmware".  I heard the printer usb driver connect / initialize in windows-
Next I started the HP firmware update utility, select your printer from drop down list.   However the display did not change to erasing firmware, then programing firmware; finally it will display "firmware rom upload complete" - or  something close to that.  The computer did do this:  the progress bar on the firmware update utility in windows completed and displayed the smiley face (about 3 min).  Then I turned the printer off - unpluged it and disconnect the usb cable from the printer. It did not load.  So where did I go wrong. 

Apple included the Gimp-Print driver "HP Laserjet 6 Series" for that printer. Does that show up?

Similar Messages

  • No printers - could not load internal printer module cache

    Suddenly this morning the dozen Bonjour printers that normally appear in the Add Printer dialog are nowhere to be seen. I reset the printing system, repaired the disk (no problems found), and rebuilt the permissions, but the problem remains. I note the following in the console after startup, and assume it has something to do with the problem:
    6/14/10 12:21:03 PM makequeues[651] Could not load internal printer module cache.
    The printer does work properly if I set it up by IP, at least. Any assistance on getting Bonjour back will be appreciated.
    Thanks,
    z

    And... I'm embarrassed to report the problem was that my ethernet was unplugged and I was accessing everything wirelessly. Plugging in brought back the printers. Also, I found the option to turn on the Bonjour access in Safari... Thanks for the input, not finding it in Safari got me to look further, ultimately in the right place.

  • HP Laserjet P1006 Can not get new print cartridge into printer.

    HP Laserjet P1006 Can not get new print cartridge into printer. Received two new cartridges from HP. CB435A, 35A are correct numbers for replacement but round part on left side appears too large for channel provided. I can not get the old cartridge back into the printer either. What am I doing wrong.

    Hi,
    Please use the following instructions to fix:
       http://www.hp.com/global/au/en/wireless/reconfiguring-system-help3.html
    For MAC filter, you have to logon to the router to see.
    Regards.
    BH
    **Click the KUDOS thumb up on the left to say 'Thanks'**
    Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

  • 4502 connects to wireless router but will not load as printer to Dell 1545 Vista x64 wireless

    HP 4502 shows and active wireless connection to router and router shows 4502 is connected and has MAC pass-thru. HP software install on Dell 1545 computer under Vista x64 was fine until the connect wireless choice was selected. Result was printer was not loaded. Dell does not have bluetooth board so couldn't use wireless direct option on printer. Printer worked well wireless at one time but when internet connection to AOL was lost something went astray. Printing test page wireless while in HP printer control software on computer works fine but that is rather boring after a while, and very frustrating trying to understand why thats' possible when printer does not show as available for connection from any other program. Have uninstalled HP software, cleaned registry, set printer to factory default, powered down and unplugged all, reinstalled from scratch twice with same result. ANy suggestions?

    Hi Sam_lost,
    Thank you for your response! I have a few more solutions for you:
    Please try going through this guide, An 'Unable to find printer' Error Displays for the HP ENVY 4500 e-All-in-One and HP Deskjet Ink Adva....
    Try this Microsoft Fix It program. Fix problems that programs cannot be installed or uninstalled.
    If those steps do not work then try the following:
    Backup your files. Back up your files.
    Re-install Windows Vista. Installing and reinstalling Windows.
    Hope this helps, and have a good day!
    RnRMusicMan
    I work on behalf of HP
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos Thumbs Up" to say “Thanks” for helping!

  • My hp laserjet m2727nf will not work until i shut off power and power back on.

    My laserjet will not work until i power off then power on after every printing job. It first started happening over the weekend when it sat idle for 2 days. Then it was once a day and now every time i need to print. What could be the problem?

    So i didn't read anything about the suggestion about the configuration report?
    I would recommand turning off wireless (if it has it), unplugging usb, unplugging network cable, unplugging fax cable. Then i would reboot the printer go to the Menu and in Reports try to print a "Configuration Report".
    If it still doesn't print i would unfortunately then may be try resetting it back to factory default. perhaps there is some setting that is causing this issue. Also causes printer to fully reinitialize itself. There should be a button in the menu and setup to set back to defaults.
    Let me know if any of that helps and what the results of trying to print an internal report are.
    I am an HP Employee.

  • [SOLVED] ALSA firmware not loading properly with kernel 3.8.6-1

    Hi All,
    I have a E-MU 1820 card + breakout box that have been working beautiful under Archlinux for years but now something happen.
    It still work OK under windows (dual boot same computer).
    Normally during boot all indicators on the breakout box blink and then only thin show is clock setting indicator. But now all the indicators still blink but instead it is a -12 dB indicator that light up and not the clock settings and no sound.
    dmesg show following.
    [christer@Arch ~]$ dmesg | grep emu
    [ 5.269612] emu1010: Special config.
    [ 5.269731] emu1010: EMU_HANA_ID = 0x7f
    [ 5.274685] emu1010: firmware file = emu/hana.fw, size = 0x133a4
    [ 13.465727] emu1010: Hana Firmware loaded
    [ 13.465776] emu1010: Hana version: 3.4
    [ 13.465864] emu1010: Card options = 0x0
    [ 13.465888] emu1010: Card options = 0x0
    [ 13.466379] emu1010: Card options3 = 0x0
    [ 14.486723] emu1010: Loading Audio Dock Firmware
    [ 16.477785] emu1010: EMU_HANA+DOCK_IRQ_STATUS = 0x36
    [ 16.477809] emu1010: EMU_HANA+DOCK_ID = 0x55
    [ 16.477809] emu1010: Audio Dock Firmware loaded
    [christer@Arch ~]$
    aplay -l looks like it did before.
    [christer@Arch ~]$ aplay -l
    **** List of PLAYBACK Hardware Devices ****
    card 0: EMU1010 [E-mu 1010 [MAEM8810]], device 0: emu10k1 [ADC Capture/Standard PCM Playback]
    Subdevices: 32/32
    Subdevice #0: subdevice #0
    Subdevice #1: subdevice #1
    Subdevice #2: subdevice #2
    Subdevice #3: subdevice #3
    Subdevice #4: subdevice #4
    Subdevice #5: subdevice #5
    Subdevice #6: subdevice #6
    Subdevice #7: subdevice #7
    Subdevice #8: subdevice #8
    Subdevice #9: subdevice #9
    Subdevice #10: subdevice #10
    Subdevice #11: subdevice #11
    Subdevice #12: subdevice #12
    Subdevice #13: subdevice #13
    Subdevice #14: subdevice #14
    Subdevice #15: subdevice #15
    Subdevice #16: subdevice #16
    Subdevice #17: subdevice #17
    Subdevice #18: subdevice #18
    Subdevice #19: subdevice #19
    Subdevice #20: subdevice #20
    Subdevice #21: subdevice #21
    Subdevice #22: subdevice #22
    Subdevice #23: subdevice #23
    Subdevice #24: subdevice #24
    Subdevice #25: subdevice #25
    Subdevice #26: subdevice #26
    Subdevice #27: subdevice #27
    Subdevice #28: subdevice #28
    Subdevice #29: subdevice #29
    Subdevice #30: subdevice #30
    Subdevice #31: subdevice #31
    card 0: EMU1010 [E-mu 1010 [MAEM8810]], device 2: emu10k1 efx [Multichannel Capture/PT Playback]
    Subdevices: 8/8
    Subdevice #0: subdevice #0
    Subdevice #1: subdevice #1
    Subdevice #2: subdevice #2
    Subdevice #3: subdevice #3
    Subdevice #4: subdevice #4
    Subdevice #5: subdevice #5
    Subdevice #6: subdevice #6
    Subdevice #7: subdevice #7
    card 0: EMU1010 [E-mu 1010 [MAEM8810]], device 3: emu10k1 [Multichannel Playback]
    Subdevices: 1/1
    Subdevice #0: subdevice #0
    [christer@Arch ~]$
    lsmod
    [christer@Arch ~]$ lsmod | grep emu
    snd_emu10k1 140245 1
    snd_util_mem 2403 1 snd_emu10k1
    snd_hwdep 6428 1 snd_emu10k1
    snd_ac97_codec 113456 1 snd_emu10k1
    snd_rawmidi 18831 1 snd_emu10k1
    snd_seq_device 5268 5 snd_seq,snd_rawmidi,snd_seq_oss,snd_emu10k1,snd_seq_dummy
    snd_pcm 78146 3 snd_pcm_oss,snd_ac97_codec,snd_emu10k1
    snd_page_alloc 7426 2 snd_pcm,snd_emu10k1
    snd_timer 18934 3 snd_pcm,snd_seq,snd_emu10k1
    snd 60156 13 snd_pcm_oss,snd_ac97_codec,snd_hwdep,snd_timer,snd_pcm,snd_seq,snd_rawmidi,snd_seq_oss,snd_emu10k1,snd_seq_device,snd_mixer_oss
    [christer@Arch ~]$
    From what I can see all looks OK, like it did when it worked, but something is not at it should.
    Any thoughts or ideas about what might have happen or how to progress in troubleshooting.
    All input most welcome.
    I found info describing  problem with firmware loading, but it is over my head.
    http://git.kernel.org/cgit/linux/kernel … 54cf7008ab
    Output from Aadebug ( http://alsa.opensrc.org/Aadebug )
    [christer@Arch ~]$ ./alsadebug
    ALSA Audio Debug v0.2.0 - Fri Apr 12 20:46:05 CEST 2013
    http://alsa.opensrc.org/aadebug
    http://www.gnu.org/licenses/agpl-3.0.txt
    Kernel ----------------------------------------------------
    Linux Arch 3.8.6-1-ARCH #1 SMP PREEMPT Sat Apr 6 07:27:01 CEST 2013 x86_64 GNU/Linux
    Advanced Linux Sound Architecture Driver Version k3.8.6-1-ARCH.
    Loaded Modules --------------------------------------------
    snd_emu10k1 139271 2
    snd_util_mem 2339 1 snd_emu10k1
    snd_hwdep 6364 1 snd_emu10k1
    snd_pcm_oss 38511 0
    snd_mixer_oss 14995 1 snd_pcm_oss
    snd_ac97_codec 112216 1 snd_emu10k1
    snd_seq_dummy 1463 0
    snd_seq_oss 29098 0
    snd_seq_midi_event 5660 1 snd_seq_oss
    snd_rawmidi 18742 1 snd_emu10k1
    snd_seq 49946 5 snd_seq_midi_event,snd_seq_oss,snd_seq_dummy
    snd_seq_device 5180 5 snd_seq,snd_rawmidi,snd_seq_oss,snd_emu10k1,snd_seq_dummy
    snd_pcm 76956 4 snd_pcm_oss,snd_ac97_codec,snd_emu10k1
    snd_page_alloc 7298 2 snd_pcm,snd_emu10k1
    snd_timer 18687 3 snd_pcm,snd_seq,snd_emu10k1
    snd 58893 14 snd_pcm_oss,snd_ac97_codec,snd_hwdep,snd_timer,snd_pcm,snd_seq,snd_rawmidi,snd_seq_oss,snd_emu10k1,snd_seq_device,snd_mixer_oss
    Proc Asound -----------------------------------------------
    0 [EMU1010 ]: Audigy2 - E-mu 1010 [MAEM8810]
    E-mu 1010 [MAEM8810] (rev.3, serial:0x40011102) at 0xd000, irq 19
    1: : sequencer
    2: [ 0- 0]: hardware dependent
    3: [ 0- 1]: raw midi
    4: [ 0- 0]: raw midi
    5: [ 0- 3]: digital audio playback
    6: [ 0- 2]: digital audio playback
    7: [ 0- 2]: digital audio capture
    8: [ 0- 1]: digital audio capture
    9: [ 0- 0]: digital audio playback
    10: [ 0- 0]: digital audio capture
    11: [ 0] : control
    33: : timer
    00-00: EMU10K1 (FX8010)
    00-00: emu10k1 : ADC Capture/Standard PCM Playback : playback 32 : capture 1
    00-01: emu10k1 mic : Mic Capture : capture 1
    00-02: emu10k1 efx : Multichannel Capture/PT Playback : playback 8 : capture 1
    00-03: emu10k1 : Multichannel Playback : playback 1
    Client info
    cur clients : 3
    peak clients : 3
    max clients : 192
    Client 0 : "System" [Kernel]
    Port 0 : "Timer" (Rwe-)
    Port 1 : "Announce" (R-e-)
    Connecting To: 15:0
    Client 14 : "Midi Through" [Kernel]
    Port 0 : "Midi Through Port-0" (RWe-)
    Client 15 : "OSS sequencer" [Kernel]
    Port 0 : "Receiver" (-we-)
    Connected From: 0:1
    Client 16 : "E-mu 1010 [MAEM8810]" [Kernel]
    Port 0 : "Audigy MPU-401 (UART)" (RWeX)
    Port 32 : "Audigy MPU-401 #2" (RWeX)
    Client 17 : "Emu10k1 WaveTable" [Kernel]
    Port 0 : "Emu10k1 Port 0" (-We-)
    Port 1 : "Emu10k1 Port 1" (-We-)
    Port 2 : "Emu10k1 Port 2" (-We-)
    Port 3 : "Emu10k1 Port 3" (-We-)
    Dev Snd ---------------------------------------------------
    total 0
    drwxr-xr-x 2 root root 60 Apr 12 20:42 by-path
    crw-rw----+ 1 root audio 116, 11 Apr 12 20:42 controlC0
    crw-rw----+ 1 root audio 116, 2 Apr 12 20:42 hwC0D0
    crw-rw----+ 1 root audio 116, 12 Apr 12 20:46 hwC0D2
    crw-rw----+ 1 root audio 116, 4 Apr 12 20:42 midiC0D0
    crw-rw----+ 1 root audio 116, 3 Apr 12 20:42 midiC0D1
    crw-rw----+ 1 root audio 116, 13 Apr 12 20:46 midiC0D2
    crw-rw----+ 1 root audio 116, 14 Apr 12 20:46 midiC0D3
    crw-rw----+ 1 root audio 116, 10 Apr 12 20:42 pcmC0D0c
    crw-rw----+ 1 root audio 116, 9 Apr 12 20:43 pcmC0D0p
    crw-rw----+ 1 root audio 116, 8 Apr 12 20:42 pcmC0D1c
    crw-rw----+ 1 root audio 116, 7 Apr 12 20:42 pcmC0D2c
    crw-rw----+ 1 root audio 116, 6 Apr 12 20:42 pcmC0D2p
    crw-rw----+ 1 root audio 116, 5 Apr 12 20:42 pcmC0D3p
    crw-rw----+ 1 root audio 116, 1 Apr 12 20:42 seq
    crw-rw----+ 1 root audio 116, 33 Apr 12 20:42 timer
    CPU -------------------------------------------------------
    model name : Intel(R) Core(TM)2 Duo CPU E8400 @ 3.00GHz
    cpu MHz : 2000.000
    model name : Intel(R) Core(TM)2 Duo CPU E8400 @ 3.00GHz
    cpu MHz : 2000.000
    RAM -------------------------------------------------------
    MemTotal: 4051696 kB
    SwapTotal: 51196 kB
    Hardware --------------------------------------------------
    01:00.0 VGA compatible controller: NVIDIA Corporation G94 [GeForce 9600 GT] (rev a1)
    05:01.0 Multimedia audio controller: Creative Labs SB Audigy (rev 03)
    Interupts -------------------------------------------------
    CPU0 CPU1
    0: 48 0 IO-APIC-edge timer
    1: 1 1 IO-APIC-edge i8042
    6: 1 2 IO-APIC-edge floppy
    8: 0 1 IO-APIC-edge rtc0
    9: 0 0 IO-APIC-fasteoi acpi
    12: 4 1 IO-APIC-edge i8042
    16: 529 493 IO-APIC-fasteoi uhci_hcd:usb1, pata_jmicron, nvidia
    18: 10654 10645 IO-APIC-fasteoi uhci_hcd:usb3, ehci_hcd:usb4, uhci_hcd:usb8, firewire_ohci, i801_smbus
    19: 3621 3626 IO-APIC-fasteoi uhci_hcd:usb7, snd_emu10k1
    21: 0 0 IO-APIC-fasteoi uhci_hcd:usb2
    23: 0 0 IO-APIC-fasteoi ehci_hcd:usb5, uhci_hcd:usb6
    44: 7637 7652 PCI-MSI-edge ahci
    45: 11719 11736 PCI-MSI-edge eth0
    NMI: 47 47 Non-maskable interrupts
    LOC: 49551 45081 Local timer interrupts
    SPU: 0 0 Spurious interrupts
    PMI: 47 47 Performance monitoring interrupts
    IWI: 0 0 IRQ work interrupts
    RTR: 0 0 APIC ICR read retries
    RES: 28730 28313 Rescheduling interrupts
    CAL: 94 54 Function call interrupts
    TLB: 3503 3509 TLB shootdowns
    TRM: 0 0 Thermal event interrupts
    THR: 0 0 Threshold APIC interrupts
    MCE: 0 0 Machine check exceptions
    MCP: 1 1 Machine check polls
    ERR: 0
    MIS: 0
    [christer@Arch ~]$
    output from systemctl show somw inacive sound related sevices.
    alsa-restore.service loaded inactive dead Restore Sound Card State
    alsa-store.service loaded inactive dead Store Sound Card State
    auditd.service error inactive dead auditd.service
    display-manager.service error inactive dead display-manager.service
    dmeventd.service loaded inactive dead Device-mapper event daemon
    emergency.service loaded inactive dead Emergency Shell
    lvmetad.service loaded inactive dead LVM2 metadata daemon
    plymouth-quit-wait.service error inactive dead plymouth-quit-wait.service
    plymouth-start.service error inactive dead plymouth-start.service
    rc-local-shutdown.service loaded inactive dead /etc/rc.local.shutdown Compatibility
    rescue.service loaded inactive dead Rescue Shell
    systemd-...console.service loaded inactive dead Dispatch Password Requests to Console
    systemd-...rd-wall.service loaded inactive dead Forward Password Requests to Wall
    systemd-fsck-root.service loaded inactive dead File System Check on Root Device
    systemd-...e8ee844.service loaded inactive dead File System Check on /dev/disk/by-uuid/9751ee37-e769-4bbe-9436-2d8e5e8ee844
    systemd-...ev-sda2.service loaded inactive dead File System Check on /dev/sda2
    systemd-...ev-sda4.service loaded inactive dead File System Check on /dev/sda4
    systemd-initctl.service loaded inactive dead /dev/initctl Compatibility Daemon
    systemd-...l-flush.service loaded inactive dead Trigger Flushing of Journal to Persistent Storage
    systemd-...ed-load.service loaded inactive dead Load Random Seed
    systemd-...ed-save.service loaded inactive dead Save Random Seed
    systemd-...ad-done.service loaded inactive dead Stop Read-Ahead Data Collection
    systemd-shutdownd.service loaded inactive dead Delayed Shutdown Service
    systemd-...s-clean.service loaded inactive dead Cleanup of Temporary Directories
    systemd-...unlevel.service loaded inactive dead Update UTMP about System Runlevel Changes
    systemd-...hutdown.service loaded inactive dead Update UTMP about System Shutdown
    ypbind.service error inactive dead ypbind.service
    emergency.target loaded inactive dead Emergency Mode
    final.target loaded inactive dead Final Step
    nss-lookup.target loaded inactive dead Host and Network Name Lookups
    nss-user-lookup.target loaded inactive dead User and Group Name Lookups
    remote-fs-pre.target loaded inactive dead Remote File Systems (Pre)
    remote-fs-setup.target error inactive dead remote-fs-setup.target
    rescue.target loaded inactive dead Rescue Mode
    runlevel1.target error inactive dead runlevel1.target
    runlevel2.target error inactive dead runlevel2.target
    runlevel3.target error inactive dead runlevel3.target
    runlevel4.target error inactive dead runlevel4.target
    runlevel5.target error inactive dead runlevel5.target
    shutdown.target loaded inactive dead Shutdown
    syslog.target error inactive dead syslog.target
    umount.target loaded inactive dead Unmount All Filesystems
    All the best!
    Christer
    Last edited by agkbill (2013-04-15 18:41:03)

    Thank you mich41!
    It looks like a kernel bug.
    I downgraded to 3.7.10-1 then firmware loaded OK and I could play sounds.
    Upgraded to 3.8.6-1 then the firmware fail to load.
    Something looks not ok with 3.8.6-1.
    Best regards,
    Christer

  • [FIXED] iSight on Macbook 2,1 - Firmware not loading

    Running the default kernel, yet lsusb gives
    Bus 001 Device 003: ID 05ac:8300 Apple, Inc. Built-in iSight (no firmware loaded)
    and I have no /dev/video0. According to the Macbook ArchWiki page, I shouldn't need isight-firmware-tools. Here's my startup log from dmesg (relevant stuff appears to show up at about 4.38 seconds):
    [ 0.000000] Initializing cgroup subsys cpuset
    [ 0.000000] Initializing cgroup subsys cpu
    [ 0.000000] Initializing cgroup subsys cpuacct
    [ 0.000000] Linux version 3.13.8-1-ARCH (tobias@testing-i686) (gcc version 4.8.2 20140206 (prerelease) (GCC) ) #1 SMP PREEMPT Tue Apr 1 12:27:17 CEST 2014
    [ 0.000000] e820: BIOS-provided physical RAM map:
    [ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000008efff] usable
    [ 0.000000] BIOS-e820: [mem 0x000000000008f000-0x000000000008ffff] ACPI NVS
    [ 0.000000] BIOS-e820: [mem 0x0000000000090000-0x000000000009ffff] usable
    [ 0.000000] BIOS-e820: [mem 0x00000000000a0000-0x00000000000bffff] reserved
    [ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x00000000be0f7fff] usable
    [ 0.000000] BIOS-e820: [mem 0x00000000be0f8000-0x00000000be2f8fff] ACPI NVS
    [ 0.000000] BIOS-e820: [mem 0x00000000be2f9000-0x00000000bee4afff] usable
    [ 0.000000] BIOS-e820: [mem 0x00000000bee4b000-0x00000000bee70fff] reserved
    [ 0.000000] BIOS-e820: [mem 0x00000000bee71000-0x00000000bee7ffff] usable
    [ 0.000000] BIOS-e820: [mem 0x00000000bee80000-0x00000000beeaafff] reserved
    [ 0.000000] BIOS-e820: [mem 0x00000000beeab000-0x00000000beeb6fff] usable
    [ 0.000000] BIOS-e820: [mem 0x00000000beeb7000-0x00000000beebbfff] ACPI data
    [ 0.000000] BIOS-e820: [mem 0x00000000beebc000-0x00000000beebdfff] usable
    [ 0.000000] BIOS-e820: [mem 0x00000000beebe000-0x00000000beeeefff] ACPI NVS
    [ 0.000000] BIOS-e820: [mem 0x00000000beeef000-0x00000000beefefff] ACPI data
    [ 0.000000] BIOS-e820: [mem 0x00000000beeff000-0x00000000bfffffff] reserved
    [ 0.000000] BIOS-e820: [mem 0x00000000f00f8000-0x00000000f00f8fff] reserved
    [ 0.000000] BIOS-e820: [mem 0x00000000fed1c000-0x00000000fed1ffff] reserved
    [ 0.000000] BIOS-e820: [mem 0x00000000fffb0000-0x00000000fffdffff] reserved
    [ 0.000000] e820: update [mem 0xbaacb010-0xbaadb03b] usable ==> usable
    [ 0.000000] extended physical RAM map:
    [ 0.000000] reserve setup_data: [mem 0x0000000000000000-0x000000000008efff] usable
    [ 0.000000] reserve setup_data: [mem 0x000000000008f000-0x000000000008ffff] ACPI NVS
    [ 0.000000] reserve setup_data: [mem 0x0000000000090000-0x000000000009ffff] usable
    [ 0.000000] reserve setup_data: [mem 0x00000000000a0000-0x00000000000bffff] reserved
    [ 0.000000] reserve setup_data: [mem 0x0000000000100000-0x00000000baacb00f] usable
    [ 0.000000] reserve setup_data: [mem 0x00000000baacb010-0x00000000baadb03b] usable
    [ 0.000000] reserve setup_data: [mem 0x00000000baadb03c-0x00000000be0f7fff] usable
    [ 0.000000] reserve setup_data: [mem 0x00000000be0f8000-0x00000000be2f8fff] ACPI NVS
    [ 0.000000] reserve setup_data: [mem 0x00000000be2f9000-0x00000000bee4afff] usable
    [ 0.000000] reserve setup_data: [mem 0x00000000bee4b000-0x00000000bee70fff] reserved
    [ 0.000000] reserve setup_data: [mem 0x00000000bee71000-0x00000000bee7ffff] usable
    [ 0.000000] reserve setup_data: [mem 0x00000000bee80000-0x00000000beeaafff] reserved
    [ 0.000000] reserve setup_data: [mem 0x00000000beeab000-0x00000000beeb6fff] usable
    [ 0.000000] reserve setup_data: [mem 0x00000000beeb7000-0x00000000beebbfff] ACPI data
    [ 0.000000] reserve setup_data: [mem 0x00000000beebc000-0x00000000beebdfff] usable
    [ 0.000000] reserve setup_data: [mem 0x00000000beebe000-0x00000000beeeefff] ACPI NVS
    [ 0.000000] reserve setup_data: [mem 0x00000000beeef000-0x00000000beefefff] ACPI data
    [ 0.000000] reserve setup_data: [mem 0x00000000beeff000-0x00000000bfffffff] reserved
    [ 0.000000] reserve setup_data: [mem 0x00000000f00f8000-0x00000000f00f8fff] reserved
    [ 0.000000] reserve setup_data: [mem 0x00000000fed1c000-0x00000000fed1ffff] reserved
    [ 0.000000] reserve setup_data: [mem 0x00000000fffb0000-0x00000000fffdffff] reserved
    [ 0.000000] Notice: NX (Execute Disable) protection cannot be enabled: non-PAE kernel!
    [ 0.000000] efi: EFI v1.10 by Apple
    [ 0.000000] efi: ACPI=0xbeefd000 ACPI 2.0=0xbeefd014 SMBIOS=0xbeebf000
    [ 0.000000] efi: mem00: type=7, attr=0xf, range=[0x0000000000000000-0x0000000000001000) (0MB)
    [ 0.000000] efi: mem01: type=2, attr=0xf, range=[0x0000000000001000-0x0000000000007000) (0MB)
    [ 0.000000] efi: mem02: type=7, attr=0xf, range=[0x0000000000007000-0x000000000008f000) (0MB)
    [ 0.000000] efi: mem03: type=10, attr=0xf, range=[0x000000000008f000-0x0000000000090000) (0MB)
    [ 0.000000] efi: mem04: type=7, attr=0xf, range=[0x0000000000090000-0x00000000000a0000) (0MB)
    [ 0.000000] efi: mem05: type=7, attr=0xf, range=[0x0000000000100000-0x0000000001000000) (15MB)
    [ 0.000000] efi: mem06: type=2, attr=0xf, range=[0x0000000001000000-0x00000000018cc000) (8MB)
    [ 0.000000] efi: mem07: type=7, attr=0xf, range=[0x00000000018cc000-0x000000007ef96000) (2006MB)
    [ 0.000000] efi: mem08: type=2, attr=0xf, range=[0x000000007ef96000-0x0000000080000000) (16MB)
    [ 0.000000] efi: mem09: type=7, attr=0xf, range=[0x0000000080000000-0x00000000ba030000) (928MB)
    [ 0.000000] efi: mem10: type=4, attr=0xf, range=[0x00000000ba030000-0x00000000ba078000) (0MB)
    [ 0.000000] efi: mem11: type=7, attr=0xf, range=[0x00000000ba078000-0x00000000baaca000) (10MB)
    [ 0.000000] efi: mem12: type=2, attr=0xf, range=[0x00000000baaca000-0x00000000baadd000) (0MB)
    [ 0.000000] efi: mem13: type=1, attr=0xf, range=[0x00000000baadd000-0x00000000bae9e000) (3MB)
    [ 0.000000] efi: mem14: type=7, attr=0xf, range=[0x00000000bae9e000-0x00000000bcec6000) (32MB)
    [ 0.000000] efi: mem15: type=4, attr=0xf, range=[0x00000000bcec6000-0x00000000bced1000) (0MB)
    [ 0.000000] efi: mem16: type=7, attr=0xf, range=[0x00000000bced1000-0x00000000bcee8000) (0MB)
    [ 0.000000] efi: mem17: type=4, attr=0xf, range=[0x00000000bcee8000-0x00000000bcf12000) (0MB)
    [ 0.000000] efi: mem18: type=7, attr=0xf, range=[0x00000000bcf12000-0x00000000bcf17000) (0MB)
    [ 0.000000] efi: mem19: type=4, attr=0xf, range=[0x00000000bcf17000-0x00000000bcf27000) (0MB)
    [ 0.000000] efi: mem20: type=7, attr=0xf, range=[0x00000000bcf27000-0x00000000bcf2b000) (0MB)
    [ 0.000000] efi: mem21: type=4, attr=0xf, range=[0x00000000bcf2b000-0x00000000bdc19000) (12MB)
    [ 0.000000] efi: mem22: type=7, attr=0xf, range=[0x00000000bdc19000-0x00000000bdc1c000) (0MB)
    [ 0.000000] efi: mem23: type=4, attr=0xf, range=[0x00000000bdc1c000-0x00000000bdc51000) (0MB)
    [ 0.000000] efi: mem24: type=7, attr=0xf, range=[0x00000000bdc51000-0x00000000bdc52000) (0MB)
    [ 0.000000] efi: mem25: type=4, attr=0xf, range=[0x00000000bdc52000-0x00000000bdd11000) (0MB)
    [ 0.000000] efi: mem26: type=7, attr=0xf, range=[0x00000000bdd11000-0x00000000bdd13000) (0MB)
    [ 0.000000] efi: mem27: type=4, attr=0xf, range=[0x00000000bdd13000-0x00000000be0f8000) (3MB)
    [ 0.000000] efi: mem28: type=10, attr=0xf, range=[0x00000000be0f8000-0x00000000be2f9000) (2MB)
    [ 0.000000] efi: mem29: type=4, attr=0xf, range=[0x00000000be2f9000-0x00000000becf8000) (9MB)
    [ 0.000000] efi: mem30: type=7, attr=0xf, range=[0x00000000becf8000-0x00000000bed3a000) (0MB)
    [ 0.000000] efi: mem31: type=3, attr=0xf, range=[0x00000000bed3a000-0x00000000bee42000) (1MB)
    [ 0.000000] efi: mem32: type=7, attr=0xf, range=[0x00000000bee42000-0x00000000bee4b000) (0MB)
    [ 0.000000] efi: mem33: type=5, attr=0x800000000000000f, range=[0x00000000bee4b000-0x00000000bee71000) (0MB)
    [ 0.000000] efi: mem34: type=7, attr=0xf, range=[0x00000000bee71000-0x00000000bee80000) (0MB)
    [ 0.000000] efi: mem35: type=6, attr=0x800000000000000f, range=[0x00000000bee80000-0x00000000beeab000) (0MB)
    [ 0.000000] efi: mem36: type=7, attr=0xf, range=[0x00000000beeab000-0x00000000beeb7000) (0MB)
    [ 0.000000] efi: mem37: type=9, attr=0xf, range=[0x00000000beeb7000-0x00000000beebc000) (0MB)
    [ 0.000000] efi: mem38: type=7, attr=0xf, range=[0x00000000beebc000-0x00000000beebe000) (0MB)
    [ 0.000000] efi: mem39: type=10, attr=0xf, range=[0x00000000beebe000-0x00000000beeef000) (0MB)
    [ 0.000000] efi: mem40: type=9, attr=0xf, range=[0x00000000beeef000-0x00000000beeff000) (0MB)
    [ 0.000000] efi: mem41: type=6, attr=0x800000000000000f, range=[0x00000000beeff000-0x00000000bef00000) (0MB)
    [ 0.000000] efi: mem42: type=0, attr=0x8000000000000000, range=[0x00000000000a0000-0x00000000000c0000) (0MB)
    [ 0.000000] efi: mem43: type=0, attr=0x8000000000000000, range=[0x00000000bef00000-0x00000000c0000000) (17MB)
    [ 0.000000] efi: mem44: type=11, attr=0x8000000000000000, range=[0x00000000f00f8000-0x00000000f00f9000) (0MB)
    [ 0.000000] efi: mem45: type=11, attr=0x8000000000000000, range=[0x00000000fed1c000-0x00000000fed20000) (0MB)
    [ 0.000000] efi: mem46: type=11, attr=0x8000000000000000, range=[0x00000000fffb0000-0x00000000fffe0000) (0MB)
    [ 0.000000] SMBIOS 2.4 present.
    [ 0.000000] DMI: Apple Inc. MacBook2,1/Mac-F4208CAA, BIOS MB21.88Z.00A5.B07.0706270922 06/27/07
    [ 0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
    [ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
    [ 0.000000] e820: last_pfn = 0xbeebe max_arch_pfn = 0x100000
    [ 0.000000] MTRR default type: uncachable
    [ 0.000000] MTRR fixed ranges enabled:
    [ 0.000000] 00000-9FFFF write-back
    [ 0.000000] A0000-BFFFF uncachable
    [ 0.000000] C0000-CFFFF write-protect
    [ 0.000000] D0000-DFFFF uncachable
    [ 0.000000] E0000-FFFFF write-protect
    [ 0.000000] MTRR variable ranges enabled:
    [ 0.000000] 0 base 0FFE00000 mask FFFE00000 write-protect
    [ 0.000000] 1 base 000000000 mask F80000000 write-back
    [ 0.000000] 2 base 080000000 mask FC0000000 write-back
    [ 0.000000] 3 base 0BF000000 mask FFF000000 uncachable
    [ 0.000000] 4 base 000000000 mask F80000000 write-back
    [ 0.000000] 5 base 080000000 mask FC0000000 write-back
    [ 0.000000] 6 base 0BEF00000 mask FFFF00000 uncachable
    [ 0.000000] 7 disabled
    [ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
    [ 0.000000] Scanning 1 areas for low memory corruption
    [ 0.000000] initial memory mapped: [mem 0x00000000-0x01bfffff]
    [ 0.000000] Base memory trampoline at [c009b000] 9b000 size 16384
    [ 0.000000] init_memory_mapping: [mem 0x00000000-0x000fffff]
    [ 0.000000] [mem 0x00000000-0x000fffff] page 4k
    [ 0.000000] init_memory_mapping: [mem 0x37000000-0x373fffff]
    [ 0.000000] [mem 0x37000000-0x373fffff] page 2M
    [ 0.000000] init_memory_mapping: [mem 0x30000000-0x36ffffff]
    [ 0.000000] [mem 0x30000000-0x36ffffff] page 2M
    [ 0.000000] init_memory_mapping: [mem 0x00100000-0x2fffffff]
    [ 0.000000] [mem 0x00100000-0x003fffff] page 4k
    [ 0.000000] [mem 0x00400000-0x2fffffff] page 2M
    [ 0.000000] init_memory_mapping: [mem 0x37400000-0x377fdfff]
    [ 0.000000] [mem 0x37400000-0x377fdfff] page 4k
    [ 0.000000] BRK [0x018ae000, 0x018aefff] PGTABLE
    [ 0.000000] RAMDISK: [mem 0x7ef96000-0x7fffffff]
    [ 0.000000] Allocated new RAMDISK: [mem 0x36794000-0x377fdfb9]
    [ 0.000000] Move RAMDISK from [mem 0x7ef96000-0x7fffffb9] to [mem 0x36794000-0x377fdfb9]
    [ 0.000000] ACPI: RSDP beefd014 000024 (v02 APPLE )
    [ 0.000000] ACPI: XSDT beefd1c0 00006C (v01 APPLE Apple00 000000A5 01000013)
    [ 0.000000] ACPI: FACP beefb000 0000F4 (v03 APPLE Apple00 000000A5 Loki 0000005F)
    [ 0.000000] ACPI: DSDT beef0000 0041E4 (v01 APPLE MacBook 00020001 INTL 20050309)
    [ 0.000000] ACPI: FACS beec0000 000040
    [ 0.000000] ACPI: HPET beefa000 000038 (v01 APPLE Apple00 00000001 Loki 0000005F)
    [ 0.000000] ACPI: APIC beef9000 000068 (v01 APPLE Apple00 00000001 Loki 0000005F)
    [ 0.000000] ACPI: MCFG beef8000 00003C (v01 APPLE Apple00 00000001 Loki 0000005F)
    [ 0.000000] ACPI: ASF! beef7000 0000A0 (v32 APPLE Apple00 00000001 Loki 0000005F)
    [ 0.000000] ACPI: SBST beef6000 000030 (v01 APPLE Apple00 00000001 Loki 0000005F)
    [ 0.000000] ACPI: ECDT beef5000 000053 (v01 APPLE Apple00 00000001 Loki 0000005F)
    [ 0.000000] ACPI: SSDT beeb9000 0001DA (v01 APPLE SataAhci 00001000 INTL 20050309)
    [ 0.000000] ACPI: SSDT beeef000 0004DC (v01 APPLE CpuPm 00003000 INTL 20050309)
    [ 0.000000] ACPI: Local APIC address 0xfee00000
    [ 0.000000] 2166MB HIGHMEM available.
    [ 0.000000] 887MB LOWMEM available.
    [ 0.000000] mapped low ram: 0 - 377fe000
    [ 0.000000] low ram: 0 - 377fe000
    [ 0.000000] BRK [0x018af000, 0x018affff] PGTABLE
    [ 0.000000] Zone ranges:
    [ 0.000000] DMA [mem 0x00001000-0x00ffffff]
    [ 0.000000] Normal [mem 0x01000000-0x377fdfff]
    [ 0.000000] HighMem [mem 0x377fe000-0xbeebdfff]
    [ 0.000000] Movable zone start for each node
    [ 0.000000] Early memory node ranges
    [ 0.000000] node 0: [mem 0x00001000-0x0008efff]
    [ 0.000000] node 0: [mem 0x00090000-0x0009ffff]
    [ 0.000000] node 0: [mem 0x00100000-0xbe0f7fff]
    [ 0.000000] node 0: [mem 0xbe2f9000-0xbee4afff]
    [ 0.000000] node 0: [mem 0xbee71000-0xbee7ffff]
    [ 0.000000] node 0: [mem 0xbeeab000-0xbeeb6fff]
    [ 0.000000] node 0: [mem 0xbeebc000-0xbeebdfff]
    [ 0.000000] On node 0 totalpages: 781317
    [ 0.000000] free_area_init_node: node 0, pgdat c1707d00, node_mem_map f4fb4020
    [ 0.000000] DMA zone: 32 pages used for memmap
    [ 0.000000] DMA zone: 0 pages reserved
    [ 0.000000] DMA zone: 3998 pages, LIFO batch:0
    [ 0.000000] Normal zone: 1744 pages used for memmap
    [ 0.000000] Normal zone: 223230 pages, LIFO batch:31
    [ 0.000000] HighMem zone: 4334 pages used for memmap
    [ 0.000000] HighMem zone: 554089 pages, LIFO batch:31
    [ 0.000000] Using APIC driver default
    [ 0.000000] ACPI: PM-Timer IO Port: 0x408
    [ 0.000000] ACPI: Local APIC address 0xfee00000
    [ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
    [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
    [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
    [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
    [ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
    [ 0.000000] IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
    [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
    [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
    [ 0.000000] ACPI: IRQ0 used by override.
    [ 0.000000] ACPI: IRQ2 used by override.
    [ 0.000000] ACPI: IRQ9 used by override.
    [ 0.000000] Using ACPI (MADT) for SMP configuration information
    [ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
    [ 0.000000] smpboot: Allowing 2 CPUs, 0 hotplug CPUs
    [ 0.000000] nr_irqs_gsi: 40
    [ 0.000000] PM: Registered nosave memory: [mem 0x0008f000-0x0008ffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0x000a0000-0x000bffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0x000c0000-0x000fffff]
    [ 0.000000] e820: [mem 0xc0000000-0xf00f7fff] available for PCI devices
    [ 0.000000] Booting paravirtualized kernel on bare hardware
    [ 0.000000] setup_percpu: NR_CPUS:8 nr_cpumask_bits:8 nr_cpu_ids:2 nr_node_ids:1
    [ 0.000000] PERCPU: Embedded 14 pages/cpu @f4f86000 s33280 r0 d24064 u57344
    [ 0.000000] pcpu-alloc: s33280 r0 d24064 u57344 alloc=14*4096
    [ 0.000000] pcpu-alloc: [0] 0 [0] 1
    [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 779541
    [ 0.000000] Kernel command line: root=/dev/sda5 ro rootfstype=btrfs systemd.unit=graphical.target initrd=EFI\arch\initramfs-arch-fallback.img
    [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
    [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
    [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
    [ 0.000000] Initializing CPU#0
    [ 0.000000] allocated 6256104 bytes of page_cgroup
    [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
    [ 0.000000] Initializing HighMem for node 0 (000377fe:000beebe)
    [ 0.000000] Memory: 3038836K/3125268K available (4472K kernel code, 448K rwdata, 1320K rodata, 588K init, 972K bss, 86432K reserved, 2186224K highmem)
    [ 0.000000] virtual kernel memory layout:
    fixmap : 0xfff15000 - 0xfffff000 ( 936 kB)
    pkmap : 0xff800000 - 0xffc00000 (4096 kB)
    vmalloc : 0xf7ffe000 - 0xff7fe000 ( 120 MB)
    lowmem : 0xc0000000 - 0xf77fe000 ( 887 MB)
    .init : 0xc171b000 - 0xc17ae000 ( 588 kB)
    .data : 0xc155e74a - 0xc171a240 (1774 kB)
    .text : 0xc1100000 - 0xc155e74a (4473 kB)
    [ 0.000000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
    [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
    [ 0.000000] Preemptible hierarchical RCU implementation.
    [ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
    [ 0.000000] Dump stacks of tasks blocking RCU-preempt GP.
    [ 0.000000] RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=2.
    [ 0.000000] NR_IRQS:2304 nr_irqs:512 16
    [ 0.000000] CPU 0 irqstacks, hard=f4408000 soft=f440a000
    [ 0.000000] Console: colour dummy device 80x25
    [ 0.000000] console [tty0] enabled
    [ 0.000000] hpet clockevent registered
    [ 0.000000] tsc: Fast TSC calibration using PIT
    [ 0.000000] tsc: Detected 2161.213 MHz processor
    [ 0.003336] Calibrating delay loop (skipped), value calculated using timer frequency.. 4324.52 BogoMIPS (lpj=7204043)
    [ 0.003340] pid_max: default: 32768 minimum: 301
    [ 0.024828] Security Framework initialized
    [ 0.024845] AppArmor: AppArmor disabled by boot time parameter
    [ 0.024847] Yama: becoming mindful.
    [ 0.024866] Mount-cache hash table entries: 512
    [ 0.025182] Initializing cgroup subsys memory
    [ 0.025193] Initializing cgroup subsys devices
    [ 0.025196] Initializing cgroup subsys freezer
    [ 0.025199] Initializing cgroup subsys net_cls
    [ 0.025202] Initializing cgroup subsys blkio
    [ 0.025241] CPU: Physical Processor ID: 0
    [ 0.025243] CPU: Processor Core ID: 0
    [ 0.025246] mce: CPU supports 6 MCE banks
    [ 0.025257] CPU0: Thermal monitoring enabled (TM2)
    [ 0.025272] Last level iTLB entries: 4KB 128, 2MB 4, 4MB 4
    Last level dTLB entries: 4KB 256, 2MB 0, 4MB 32
    tlb_flushall_shift: -1
    [ 0.025387] Freeing SMP alternatives memory: 20K (c17ae000 - c17b3000)
    [ 0.026346] ACPI: Core revision 20131115
    [ 0.029337] ACPI: All ACPI Tables successfully acquired
    [ 0.031575] ftrace: allocating 20090 entries in 40 pages
    [ 0.040091] Enabling APIC mode: Flat. Using 1 I/O APICs
    [ 0.040528] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
    [ 0.073872] smpboot: CPU0: Intel(R) Core(TM)2 CPU T7400 @ 2.16GHz (fam: 06, model: 0f, stepping: 06)
    [ 0.076666] Performance Events: PEBS fmt0-, 4-deep LBR, Core2 events, Intel PMU driver.
    [ 0.076666] perf_event_intel: PEBS disabled due to CPU errata
    [ 0.076666] ... version: 2
    [ 0.076666] ... bit width: 40
    [ 0.076666] ... generic registers: 2
    [ 0.076666] ... value mask: 000000ffffffffff
    [ 0.076666] ... max period: 000000007fffffff
    [ 0.076666] ... fixed-purpose events: 3
    [ 0.076666] ... event mask: 0000000700000003
    [ 0.096743] CPU 1 irqstacks, hard=f44cc000 soft=f44ce000
    [ 0.096746] x86: Booting SMP configuration:
    [ 0.006666] Initializing CPU#1
    [ 0.109977] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
    [ 0.096748] .... node #0, CPUs: #1
    [ 0.109995] x86: Booted up 1 node, 2 CPUs
    [ 0.109999] smpboot: Total of 2 processors activated (8648.05 BogoMIPS)
    [ 0.112323] devtmpfs: initialized
    [ 0.112323] PM: Registering ACPI NVS region [mem 0x0008f000-0x0008ffff] (4096 bytes)
    [ 0.112323] PM: Registering ACPI NVS region [mem 0xbe0f8000-0xbe2f8fff] (2101248 bytes)
    [ 0.112323] PM: Registering ACPI NVS region [mem 0xbeebe000-0xbeeeefff] (200704 bytes)
    [ 0.112323] RTC time: 2:13:52, date: 04/03/14
    [ 0.112323] NET: Registered protocol family 16
    [ 0.112323] cpuidle: using governor ladder
    [ 0.112323] cpuidle: using governor menu
    [ 0.112323] ACPI: bus type PCI registered
    [ 0.112323] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
    [ 0.112323] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xf0000000-0xffffffff] (base 0xf0000000)
    [ 0.112323] PCI: not using MMCONFIG
    [ 0.125963] PCI: Using configuration type 1 for base access
    [ 0.130090] bio: create slab <bio-0> at 0
    [ 0.130110] ACPI: Added _OSI(Module Device)
    [ 0.130110] ACPI: Added _OSI(Processor Device)
    [ 0.130110] ACPI: Added _OSI(3.0 _SCP Extensions)
    [ 0.130110] ACPI: Added _OSI(Processor Aggregator Device)
    [ 0.131070] ACPI : EC: EC description table is found, configuring boot EC
    [ 0.133507] [Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored
    [ 0.144021] ACPI: SSDT beeb8c10 0002AE (v01 APPLE Cpu0Ist 00003000 INTL 20050309)
    [ 0.144265] ACPI: Dynamic OEM Table Load:
    [ 0.144268] ACPI: SSDT (null) 0002AE (v01 APPLE Cpu0Ist 00003000 INTL 20050309)
    [ 0.144381] ACPI: SSDT beeb8910 0002A0 (v01 APPLE Cpu0Cst 00003001 INTL 20050309)
    [ 0.144605] ACPI: Dynamic OEM Table Load:
    [ 0.144608] ACPI: SSDT (null) 0002A0 (v01 APPLE Cpu0Cst 00003001 INTL 20050309)
    [ 0.153597] ACPI: SSDT beeb8f10 000087 (v01 APPLE Cpu1Ist 00003000 INTL 20050309)
    [ 0.153830] ACPI: Dynamic OEM Table Load:
    [ 0.153833] ACPI: SSDT (null) 000087 (v01 APPLE Cpu1Ist 00003000 INTL 20050309)
    [ 0.153929] ACPI: SSDT beeb7f10 000085 (v01 APPLE Cpu1Cst 00003000 INTL 20050309)
    [ 0.154154] ACPI: Dynamic OEM Table Load:
    [ 0.154157] ACPI: SSDT (null) 000085 (v01 APPLE Cpu1Cst 00003000 INTL 20050309)
    [ 0.173527] ACPI: Interpreter enabled
    [ 0.173543] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S1_] (20131115/hwxface-580)
    [ 0.173549] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S2_] (20131115/hwxface-580)
    [ 0.173567] ACPI: (supports S0 S3 S4 S5)
    [ 0.173569] ACPI: Using IOAPIC for interrupt routing
    [ 0.173590] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xf0000000-0xffffffff] (base 0xf0000000)
    [ 0.174736] PCI: MMCONFIG at [mem 0xf0000000-0xffffffff] reserved in ACPI motherboard resources
    [ 0.174741] PCI: MMCONFIG for 0000 [bus00-3f] at [mem 0xf0000000-0xf3ffffff] (base 0xf0000000) (size reduced!)
    [ 0.174743] PCI: Using MMCONFIG for extended config space
    [ 0.174760] PCI: Ignoring host bridge windows from ACPI; if necessary, use "pci=use_crs" and report a bug
    [ 0.174914] ACPI: No dock devices found.
    [ 0.187223] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
    [ 0.187231] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI]
    [ 0.187699] acpi PNP0A08:00: _OSC: OS now controls [PCIeHotplug PME AER PCIeCapability]
    [ 0.188040] acpi PNP0A08:00: host bridge window [io 0x0000-0x0cf7] (ignored)
    [ 0.188044] acpi PNP0A08:00: host bridge window [io 0x0d00-0xffff] (ignored)
    [ 0.188048] acpi PNP0A08:00: host bridge window [mem 0x000a0000-0x000bffff] (ignored)
    [ 0.188051] acpi PNP0A08:00: host bridge window [mem 0x000c0000-0x000c3fff] (ignored)
    [ 0.188054] acpi PNP0A08:00: host bridge window [mem 0x000c4000-0x000c7fff] (ignored)
    [ 0.188057] acpi PNP0A08:00: host bridge window [mem 0x000c8000-0x000cbfff] (ignored)
    [ 0.188060] acpi PNP0A08:00: host bridge window [mem 0x000cc000-0x000cffff] (ignored)
    [ 0.188063] acpi PNP0A08:00: host bridge window [mem 0x000d0000-0x000d3fff] (ignored)
    [ 0.188066] acpi PNP0A08:00: host bridge window [mem 0x000d4000-0x000d7fff] (ignored)
    [ 0.188069] acpi PNP0A08:00: host bridge window [mem 0x000d8000-0x000dbfff] (ignored)
    [ 0.188072] acpi PNP0A08:00: host bridge window [mem 0x000dc000-0x000dffff] (ignored)
    [ 0.188075] acpi PNP0A08:00: host bridge window [mem 0x000e0000-0x000e3fff] (ignored)
    [ 0.188079] acpi PNP0A08:00: host bridge window [mem 0x000e4000-0x000e7fff] (ignored)
    [ 0.188082] acpi PNP0A08:00: host bridge window [mem 0x000e8000-0x000ebfff] (ignored)
    [ 0.188085] acpi PNP0A08:00: host bridge window [mem 0x000ec000-0x000effff] (ignored)
    [ 0.188088] acpi PNP0A08:00: host bridge window [mem 0x000f0000-0x000fffff] (ignored)
    [ 0.188091] acpi PNP0A08:00: host bridge window [mem 0xc0000000-0xfebfffff] (ignored)
    [ 0.188094] PCI: root bus 00: using default resources
    [ 0.188097] acpi PNP0A08:00: [Firmware Info]: MMCONFIG for domain 0000 [bus 00-3f] only partially covers this bridge
    [ 0.188289] PCI host bridge to bus 0000:00
    [ 0.188294] pci_bus 0000:00: root bus resource [bus 00-ff]
    [ 0.188297] pci_bus 0000:00: root bus resource [io 0x0000-0xffff]
    [ 0.188300] pci_bus 0000:00: root bus resource [mem 0x00000000-0xffffffff]
    [ 0.188313] pci 0000:00:00.0: [8086:27a0] type 00 class 0x060000
    [ 0.188442] pci 0000:00:02.0: [8086:27a2] type 00 class 0x030000
    [ 0.188457] pci 0000:00:02.0: reg 0x10: [mem 0xd0380000-0xd03fffff]
    [ 0.188465] pci 0000:00:02.0: reg 0x14: [io 0x20e0-0x20e7]
    [ 0.188473] pci 0000:00:02.0: reg 0x18: [mem 0xc0000000-0xcfffffff pref]
    [ 0.188480] pci 0000:00:02.0: reg 0x1c: [mem 0xd0400000-0xd043ffff]
    [ 0.188609] pci 0000:00:02.1: [8086:27a6] type 00 class 0x038000
    [ 0.188619] pci 0000:00:02.1: reg 0x10: [mem 0xd0300000-0xd037ffff]
    [ 0.190132] pci 0000:00:07.0: [8086:27a3] type 00 class 0x110100
    [ 0.190145] pci 0000:00:07.0: reg 0x10: [mem 0xd0444000-0xd0444fff]
    [ 0.190315] pci 0000:00:1b.0: [8086:27d8] type 00 class 0x040300
    [ 0.190337] pci 0000:00:1b.0: reg 0x10: [mem 0xd0440000-0xd0443fff 64bit]
    [ 0.190432] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
    [ 0.190548] pci 0000:00:1c.0: [8086:27d0] type 01 class 0x060400
    [ 0.190664] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
    [ 0.190779] pci 0000:00:1c.1: [8086:27d2] type 01 class 0x060400
    [ 0.190894] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
    [ 0.191014] pci 0000:00:1d.0: [8086:27c8] type 00 class 0x0c0300
    [ 0.191074] pci 0000:00:1d.0: reg 0x20: [io 0x2080-0x209f]
    [ 0.191174] pci 0000:00:1d.0: System wakeup disabled by ACPI
    [ 0.191228] pci 0000:00:1d.1: [8086:27c9] type 00 class 0x0c0300
    [ 0.191288] pci 0000:00:1d.1: reg 0x20: [io 0x2060-0x207f]
    [ 0.191386] pci 0000:00:1d.1: System wakeup disabled by ACPI
    [ 0.191437] pci 0000:00:1d.2: [8086:27ca] type 00 class 0x0c0300
    [ 0.191497] pci 0000:00:1d.2: reg 0x20: [io 0x2040-0x205f]
    [ 0.191595] pci 0000:00:1d.2: System wakeup disabled by ACPI
    [ 0.191648] pci 0000:00:1d.3: [8086:27cb] type 00 class 0x0c0300
    [ 0.191707] pci 0000:00:1d.3: reg 0x20: [io 0x2020-0x203f]
    [ 0.191805] pci 0000:00:1d.3: System wakeup disabled by ACPI
    [ 0.191871] pci 0000:00:1d.7: [8086:27cc] type 00 class 0x0c0320
    [ 0.191895] pci 0000:00:1d.7: reg 0x10: [mem 0xd0445400-0xd04457ff]
    [ 0.191989] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
    [ 0.192048] pci 0000:00:1d.7: System wakeup disabled by ACPI
    [ 0.192103] pci 0000:00:1e.0: [8086:2448] type 01 class 0x060401
    [ 0.192280] pci 0000:00:1f.0: [8086:27b9] type 00 class 0x060100
    [ 0.192399] pci 0000:00:1f.0: address space collision: [io 0x0400-0x047f] conflicts with ACPI CPU throttle [??? 0x00000410-0x00000415 flags 0x80000000]
    [ 0.192407] pci 0000:00:1f.0: quirk: [io 0x0500-0x053f] claimed by ICH6 GPIO
    [ 0.192412] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 0680 (mask 000f)
    [ 0.192417] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 2 PIO at 1640 (mask 000f)
    [ 0.192424] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 4 PIO at 0300 (mask 001f)
    [ 0.192557] pci 0000:00:1f.1: [8086:27df] type 00 class 0x01018f
    [ 0.192576] pci 0000:00:1f.1: reg 0x10: [io 0x20d8-0x20df]
    [ 0.192589] pci 0000:00:1f.1: reg 0x14: [io 0x20f4-0x20f7]
    [ 0.192602] pci 0000:00:1f.1: reg 0x18: [io 0x20d0-0x20d7]
    [ 0.192616] pci 0000:00:1f.1: reg 0x1c: [io 0x20f0-0x20f3]
    [ 0.192628] pci 0000:00:1f.1: reg 0x20: [io 0x20b0-0x20bf]
    [ 0.192752] pci 0000:00:1f.2: [8086:27c5] type 00 class 0x010601
    [ 0.192778] pci 0000:00:1f.2: reg 0x10: [io 0x20c8-0x20cf]
    [ 0.192792] pci 0000:00:1f.2: reg 0x14: [io 0x20ec-0x20ef]
    [ 0.192805] pci 0000:00:1f.2: reg 0x18: [io 0x20c0-0x20c7]
    [ 0.192818] pci 0000:00:1f.2: reg 0x1c: [io 0x20e8-0x20eb]
    [ 0.192831] pci 0000:00:1f.2: reg 0x20: [io 0x20a0-0x20af]
    [ 0.192844] pci 0000:00:1f.2: reg 0x24: [mem 0xd0445000-0xd04453ff]
    [ 0.192905] pci 0000:00:1f.2: PME# supported from D3hot
    [ 0.193010] pci 0000:00:1f.3: [8086:27da] type 00 class 0x0c0500
    [ 0.193068] pci 0000:00:1f.3: reg 0x20: [io 0xefa0-0xefbf]
    [ 0.193303] pci 0000:01:00.0: [11ab:4362] type 00 class 0x020000
    [ 0.193340] pci 0000:01:00.0: reg 0x10: [mem 0xd0200000-0xd0203fff 64bit]
    [ 0.193358] pci 0000:01:00.0: reg 0x18: [io 0x1000-0x10ff]
    [ 0.193421] pci 0000:01:00.0: reg 0x30: [mem 0xfffe0000-0xffffffff pref]
    [ 0.193520] pci 0000:01:00.0: supports D1 D2
    [ 0.193523] pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold
    [ 0.193561] pci 0000:01:00.0: System wakeup disabled by ACPI
    [ 0.193605] pci 0000:01:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force'
    [ 0.193619] pci 0000:00:1c.0: PCI bridge to [bus 01]
    [ 0.193625] pci 0000:00:1c.0: bridge window [io 0x1000-0x1fff]
    [ 0.193631] pci 0000:00:1c.0: bridge window [mem 0xd0200000-0xd02fffff]
    [ 0.193763] pci 0000:02:00.0: [168c:0024] type 00 class 0x028000
    [ 0.193793] pci 0000:02:00.0: reg 0x10: [mem 0xd0100000-0xd010ffff 64bit]
    [ 0.193938] pci 0000:02:00.0: supports D1
    [ 0.193941] pci 0000:02:00.0: PME# supported from D0 D1 D3hot
    [ 0.193991] pci 0000:02:00.0: System wakeup disabled by ACPI
    [ 0.194036] pci 0000:02:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force'
    [ 0.194050] pci 0000:00:1c.1: PCI bridge to [bus 02]
    [ 0.194059] pci 0000:00:1c.1: bridge window [mem 0xd0100000-0xd01fffff]
    [ 0.194150] pci 0000:03:03.0: [11c1:5811] type 00 class 0x0c0010
    [ 0.194175] pci 0000:03:03.0: reg 0x10: [mem 0xd0000000-0xd0000fff]
    [ 0.194282] pci 0000:03:03.0: supports D1 D2
    [ 0.194285] pci 0000:03:03.0: PME# supported from D0 D1 D2 D3hot
    [ 0.194405] pci 0000:00:1e.0: PCI bridge to [bus 03] (subtractive decode)
    [ 0.194415] pci 0000:00:1e.0: bridge window [mem 0xd0000000-0xd00fffff]
    [ 0.194424] pci 0000:00:1e.0: bridge window [io 0x0000-0xffff] (subtractive decode)
    [ 0.194427] pci 0000:00:1e.0: bridge window [mem 0x00000000-0xffffffff] (subtractive decode)
    [ 0.194458] pci_bus 0000:00: on NUMA node 0
    [ 0.194667] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 12 14 15) *0, disabled.
    [ 0.194750] ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 11 12 14 15) *0, disabled.
    [ 0.194831] ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 10 12 14 15) *0, disabled.
    [ 0.194914] ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 11 12 14 15) *0, disabled.
    [ 0.194994] ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 7 10 12 14 15) *0, disabled.
    [ 0.195073] ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 7 11 12 14 15) *0, disabled.
    [ 0.195152] ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 7 10 12 14 15) *0, disabled.
    [ 0.195231] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 11 12 14 15) *0, disabled.
    [ 0.196881] ACPI: Enabled 5 GPEs in block 00 to 1F
    [ 0.196893] ACPI: \_SB_.PCI0: notify handler is installed
    [ 0.196941] Found 1 acpi root devices
    [ 0.196975] ACPI : EC: GPE = 0x17, I/O: command/status = 0x66, data = 0x62
    [ 0.197034] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
    [ 0.197034] vgaarb: loaded
    [ 0.197034] vgaarb: bridge control possible 0000:00:02.0
    [ 0.197034] PCI: Using ACPI for IRQ routing
    [ 0.200581] PCI: pci_cache_line_size set to 64 bytes
    [ 0.200654] e820: reserve RAM buffer [mem 0x0008f000-0x0008ffff]
    [ 0.200657] e820: reserve RAM buffer [mem 0xbaacb010-0xbbffffff]
    [ 0.200659] e820: reserve RAM buffer [mem 0xbe0f8000-0xbfffffff]
    [ 0.200662] e820: reserve RAM buffer [mem 0xbee4b000-0xbfffffff]
    [ 0.200665] e820: reserve RAM buffer [mem 0xbee80000-0xbfffffff]
    [ 0.200667] e820: reserve RAM buffer [mem 0xbeeb7000-0xbfffffff]
    [ 0.200670] e820: reserve RAM buffer [mem 0xbeebe000-0xbfffffff]
    [ 0.200795] NetLabel: Initializing
    [ 0.200797] NetLabel: domain hash size = 128
    [ 0.200799] NetLabel: protocols = UNLABELED CIPSOv4
    [ 0.200814] NetLabel: unlabeled traffic allowed by default
    [ 0.200862] HPET: 3 timers in total, 0 timers will be used for per-cpu timer
    [ 0.200869] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
    [ 0.200875] hpet0: 3 comparators, 64-bit 14.318180 MHz counter
    [ 0.202899] Switched to clocksource hpet
    [ 0.207652] pnp: PnP ACPI init
    [ 0.207675] ACPI: bus type PNP registered
    [ 0.207781] system 00:00: [mem 0xf0000000-0xf3ffffff] could not be reserved
    [ 0.207785] system 00:00: [mem 0xfed14000-0xfed17fff] has been reserved
    [ 0.207789] system 00:00: [mem 0xfed18000-0xfed18fff] has been reserved
    [ 0.207792] system 00:00: [mem 0xfed19000-0xfed19fff] has been reserved
    [ 0.207796] system 00:00: [mem 0xfed1c000-0xfed1ffff] has been reserved
    [ 0.207799] system 00:00: [mem 0xfed20000-0xfed8ffff] has been reserved
    [ 0.207805] system 00:00: Plug and Play ACPI device, IDs PNP0c02 (active)
    [ 0.208094] pnp 00:01: Plug and Play ACPI device, IDs APP0001 (active)
    [ 0.208143] pnp 00:02: [dma 4]
    [ 0.208184] pnp 00:02: Plug and Play ACPI device, IDs PNP0200 (active)
    [ 0.208229] pnp 00:03: Plug and Play ACPI device, IDs INT0800 (active)
    [ 0.208366] system 00:04: [mem 0xfed00000-0xfed003ff] has been reserved
    [ 0.208371] system 00:04: Plug and Play ACPI device, IDs PNP0103 PNP0c01 (active)
    [ 0.208428] pnp 00:05: Plug and Play ACPI device, IDs PNP0c04 (active)
    [ 0.208468] pnp 00:06: disabling [io 0x1640-0x164f] because it overlaps 0000:00:1c.0 BAR 13 [io 0x1000-0x1fff]
    [ 0.208526] system 00:06: [io 0x0680-0x06ef] has been reserved
    [ 0.208530] system 00:06: [io 0x0800-0x080f] has been reserved
    [ 0.208533] system 00:06: [io 0x0810-0x0817] has been reserved
    [ 0.208536] system 00:06: [io 0x0400-0x047f] could not be reserved
    [ 0.208540] system 00:06: [io 0x0500-0x053f] has been reserved
    [ 0.208544] system 00:06: Plug and Play ACPI device, IDs PNP0c02 (active)
    [ 0.208593] pnp 00:07: Plug and Play ACPI device, IDs PNP0b00 (active)
    [ 0.212349] pnp: PnP ACPI: found 8 devices
    [ 0.212351] ACPI: bus type PNP unregistered
    [ 0.250634] pci 0000:01:00.0: no compatible bridge window for [mem 0xfffe0000-0xffffffff pref]
    [ 0.250654] pci 0000:00:1c.0: bridge window [mem 0x00100000-0x001fffff pref] to [bus 01] add_size 200000
    [ 0.250667] pci 0000:00:1c.1: bridge window [io 0x1000-0x0fff] to [bus 02] add_size 1000
    [ 0.250672] pci 0000:00:1c.1: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 02] add_size 200000
    [ 0.250687] pci 0000:00:1f.0: BAR 13: [io 0x0400-0x047f] has bogus alignment
    [ 0.250694] pci 0000:00:1c.0: res[15]=[mem 0x00100000-0x001fffff pref] get_res_add_size add_size 200000
    [ 0.250698] pci 0000:00:1c.1: res[15]=[mem 0x00100000-0x000fffff 64bit pref] get_res_add_size add_size 200000
    [ 0.250701] pci 0000:00:1c.1: res[13]=[io 0x1000-0x0fff] get_res_add_size add_size 1000
    [ 0.250707] pci 0000:00:1c.0: BAR 15: assigned [mem 0xd0500000-0xd07fffff pref]
    [ 0.250712] pci 0000:00:1c.1: BAR 15: assigned [mem 0xd0800000-0xd09fffff 64bit pref]
    [ 0.250716] pci 0000:00:1c.1: BAR 13: assigned [io 0x3000-0x3fff]
    [ 0.250721] pci 0000:01:00.0: BAR 6: assigned [mem 0xd0500000-0xd051ffff pref]
    [ 0.250725] pci 0000:00:1c.0: PCI bridge to [bus 01]
    [ 0.250730] pci 0000:00:1c.0: bridge window [io 0x1000-0x1fff]
    [ 0.250737] pci 0000:00:1c.0: bridge window [mem 0xd0200000-0xd02fffff]
    [ 0.250743] pci 0000:00:1c.0: bridge window [mem 0xd0500000-0xd07fffff pref]
    [ 0.250752] pci 0000:00:1c.1: PCI bridge to [bus 02]
    [ 0.250756] pci 0000:00:1c.1: bridge window [io 0x3000-0x3fff]
    [ 0.250763] pci 0000:00:1c.1: bridge window [mem 0xd0100000-0xd01fffff]
    [ 0.250770] pci 0000:00:1c.1: bridge window [mem 0xd0800000-0xd09fffff 64bit pref]
    [ 0.250778] pci 0000:00:1e.0: PCI bridge to [bus 03]
    [ 0.250786] pci 0000:00:1e.0: bridge window [mem 0xd0000000-0xd00fffff]
    [ 0.250798] pci_bus 0000:00: resource 4 [io 0x0000-0xffff]
    [ 0.250801] pci_bus 0000:00: resource 5 [mem 0x00000000-0xffffffff]
    [ 0.250805] pci_bus 0000:01: resource 0 [io 0x1000-0x1fff]
    [ 0.250808] pci_bus 0000:01: resource 1 [mem 0xd0200000-0xd02fffff]
    [ 0.250811] pci_bus 0000:01: resource 2 [mem 0xd0500000-0xd07fffff pref]
    [ 0.250814] pci_bus 0000:02: resource 0 [io 0x3000-0x3fff]
    [ 0.250817] pci_bus 0000:02: resource 1 [mem 0xd0100000-0xd01fffff]
    [ 0.250820] pci_bus 0000:02: resource 2 [mem 0xd0800000-0xd09fffff 64bit pref]
    [ 0.250823] pci_bus 0000:03: resource 1 [mem 0xd0000000-0xd00fffff]
    [ 0.250826] pci_bus 0000:03: resource 4 [io 0x0000-0xffff]
    [ 0.250829] pci_bus 0000:03: resource 5 [mem 0x00000000-0xffffffff]
    [ 0.250879] NET: Registered protocol family 2
    [ 0.251083] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
    [ 0.251103] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
    [ 0.251133] TCP: Hash tables configured (established 8192 bind 8192)
    [ 0.251164] TCP: reno registered
    [ 0.251167] UDP hash table entries: 512 (order: 2, 16384 bytes)
    [ 0.251178] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
    [ 0.251249] NET: Registered protocol family 1
    [ 0.251265] pci 0000:00:02.0: Boot video device
    [ 0.252430] pci 0000:00:1d.7: enabling device (0000 -> 0002)
    [ 0.252740] PCI: CLS mismatch (256 != 64), using 64 bytes
    [ 0.252796] Unpacking initramfs...
    [ 0.711581] Freeing initrd memory: 16808K (f6794000 - f77fe000)
    [ 0.711803] apm: BIOS not found.
    [ 0.711854] Scanning for low memory corruption every 60 seconds
    [ 0.712353] audit: initializing netlink socket (disabled)
    [ 0.712374] type=2000 audit(1396491231.709:1): initialized
    [ 0.727981] bounce pool size: 64 pages
    [ 0.727995] HugeTLB registered 4 MB page size, pre-allocated 0 pages
    [ 0.730140] zbud: loaded
    [ 0.730279] VFS: Disk quotas dquot_6.5.2
    [ 0.730349] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
    [ 0.730612] msgmni has been set to 1756
    [ 0.730696] Key type big_key registered
    [ 0.731049] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
    [ 0.731109] io scheduler noop registered
    [ 0.731112] io scheduler deadline registered
    [ 0.731157] io scheduler cfq registered (default)
    [ 0.731244] pcieport 0000:00:1c.0: device [8086:27d0] has invalid IRQ; check vendor BIOS
    [ 0.731473] pcieport 0000:00:1c.0: irq 40 for MSI/MSI-X
    [ 0.731596] pcieport 0000:00:1c.1: device [8086:27d2] has invalid IRQ; check vendor BIOS
    [ 0.731773] pcieport 0000:00:1c.1: irq 41 for MSI/MSI-X
    [ 0.731939] pcieport 0000:00:1c.0: Signaling PME through PCIe PME interrupt
    [ 0.731942] pci 0000:01:00.0: Signaling PME through PCIe PME interrupt
    [ 0.731948] pcie_pme 0000:00:1c.0:pcie01: service driver pcie_pme loaded
    [ 0.731975] pcieport 0000:00:1c.1: Signaling PME through PCIe PME interrupt
    [ 0.731978] pci 0000:02:00.0: Signaling PME through PCIe PME interrupt
    [ 0.731984] pcie_pme 0000:00:1c.1:pcie01: service driver pcie_pme loaded
    [ 0.732004] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
    [ 0.732058] pciehp 0000:00:1c.0:pcie04: HPC vendor_id 8086 device_id 27d0 ss_vid 0 ss_did 0
    [ 0.732098] pciehp 0000:00:1c.0:pcie04: service driver pciehp loaded
    [ 0.732115] pciehp 0000:00:1c.1:pcie04: HPC vendor_id 8086 device_id 27d2 ss_vid 0 ss_did 0
    [ 0.732151] pciehp 0000:00:1c.1:pcie04: service driver pciehp loaded
    [ 0.732159] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
    [ 0.732240] intel_idle: does not run on family 6 model 15
    [ 0.732271] GHES: HEST is not enabled!
    [ 0.732286] isapnp: Scanning for PnP cards...
    [ 1.089038] isapnp: No Plug & Play device found
    [ 1.089104] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
    [ 1.089870] rtc_cmos 00:07: RTC can wake from S4
    [ 1.090053] rtc_cmos 00:07: rtc core: registered rtc_cmos as rtc0
    [ 1.090089] rtc_cmos 00:07: alarms up to one month, y3k, 242 bytes nvram, hpet irqs
    [ 1.090225] drop_monitor: Initializing network drop monitor service
    [ 1.090318] TCP: cubic registered
    [ 1.090466] NET: Registered protocol family 10
    [ 1.090724] NET: Registered protocol family 17
    [ 1.090736] Key type dns_resolver registered
    [ 1.090918] Using IPI No-Shortcut mode
    [ 1.091080] registered taskstats version 1
    [ 1.091660] Magic number: 10:587:206
    [ 1.091735] rtc_cmos 00:07: setting system clock to 2014-04-03 02:13:53 UTC (1396491233)
    [ 1.091810] PM: Hibernation image not present or could not be loaded.
    [ 1.092134] Freeing unused kernel memory: 588K (c171b000 - c17ae000)
    [ 1.092258] Write protecting the kernel text: 4476k
    [ 1.092297] Write protecting the kernel read-only data: 1324k
    [ 1.101141] random: systemd-tmpfile urandom read with 3 bits of entropy available
    [ 1.103059] systemd-udevd[48]: starting version 212
    [ 1.105813] Linux agpgart interface v0.103
    [ 1.107850] [drm] Initialized drm 1.1.0 20060810
    [ 1.108901] agpgart-intel 0000:00:00.0: Intel 945GM Chipset
    [ 1.109016] agpgart-intel 0000:00:00.0: detected gtt size: 262144K total, 262144K mappable
    [ 1.110230] agpgart-intel 0000:00:00.0: detected 16384K stolen memory
    [ 1.110426] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xc0000000
    [ 1.111004] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input0
    [ 1.111050] ACPI: Lid Switch [LID0]
    [ 1.111122] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1
    [ 1.111128] ACPI: Power Button [PWRB]
    [ 1.111194] input: Sleep Button as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input2
    [ 1.111198] ACPI: Sleep Button [SLPB]
    [ 1.111287] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
    [ 1.111291] ACPI: Power Button [PWRF]
    [ 1.111681] ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no)
    [ 1.111840] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:00/input/input4
    [ 1.118232] [drm] Memory usable by graphics device = 256M
    [ 1.118511] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
    [ 1.118513] [drm] Driver supports precise vblank timestamp query.
    [ 1.118526] i915 0000:00:02.0: Invalid ROM contents
    [ 1.118533] [drm] failed to find VBIOS tables
    [ 1.118590] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
    [ 1.289208] [drm] initialized overlay support
    [ 1.713356] tsc: Refined TSC clocksource calibration: 2161.249 MHz
    [ 1.866111] fbcon: inteldrmfb (fb0) is primary device
    [ 2.222132] Console: switching to colour frame buffer device 160x50
    [ 2.227666] i915 0000:00:02.0: fb0: inteldrmfb frame buffer device
    [ 2.227669] i915 0000:00:02.0: registered panic notifier
    [ 2.227679] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
    [ 2.271425] SCSI subsystem initialized
    [ 2.274827] libata version 3.00 loaded.
    [ 2.276074] ACPI: bus type USB registered
    [ 2.276110] usbcore: registered new interface driver usbfs
    [ 2.276125] usbcore: registered new interface driver hub
    [ 2.276175] usbcore: registered new device driver usb
    [ 2.277269] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
    [ 2.277466] ehci-pci: EHCI PCI platform driver
    [ 2.277706] ehci-pci 0000:00:1d.7: EHCI Host Controller
    [ 2.277715] ehci-pci 0000:00:1d.7: new USB bus registered, assigned bus number 1
    [ 2.277734] ehci-pci 0000:00:1d.7: debug port 1
    [ 2.281643] ehci-pci 0000:00:1d.7: cache line size of 64 is not supported
    [ 2.281670] ehci-pci 0000:00:1d.7: irq 21, io mem 0xd0445400
    [ 2.282153] uhci_hcd: USB Universal Host Controller Interface driver
    [ 2.290028] ehci-pci 0000:00:1d.7: USB 2.0 started, EHCI 1.00
    [ 2.290299] hub 1-0:1.0: USB hub found
    [ 2.290310] hub 1-0:1.0: 8 ports detected
    [ 2.291047] uhci_hcd 0000:00:1d.0: UHCI Host Controller
    [ 2.291057] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
    [ 2.291089] uhci_hcd 0000:00:1d.0: irq 21, io base 0x00002080
    [ 2.291321] hub 2-0:1.0: USB hub found
    [ 2.291332] hub 2-0:1.0: 2 ports detected
    [ 2.291663] uhci_hcd 0000:00:1d.1: UHCI Host Controller
    [ 2.291671] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
    [ 2.291701] uhci_hcd 0000:00:1d.1: irq 19, io base 0x00002060
    [ 2.292107] hub 3-0:1.0: USB hub found
    [ 2.292118] hub 3-0:1.0: 2 ports detected
    [ 2.292428] uhci_hcd 0000:00:1d.2: UHCI Host Controller
    [ 2.292435] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
    [ 2.292482] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00002040
    [ 2.292686] hub 4-0:1.0: USB hub found
    [ 2.292697] hub 4-0:1.0: 2 ports detected
    [ 2.293011] uhci_hcd 0000:00:1d.3: UHCI Host Controller
    [ 2.293018] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
    [ 2.293049] uhci_hcd 0000:00:1d.3: irq 16, io base 0x00002020
    [ 2.293454] hub 5-0:1.0: USB hub found
    [ 2.293465] hub 5-0:1.0: 2 ports detected
    [ 2.293800] ahci 0000:00:1f.2: version 3.0
    [ 2.293994] ahci 0000:00:1f.2: irq 42 for MSI/MSI-X
    [ 2.294079] ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 4 ports 1.5 Gbps 0x4 impl SATA mode
    [ 2.294084] ahci 0000:00:1f.2: flags: 64bit ncq ilck pm led clo pio slum part
    [ 2.299571] scsi0 : ahci
    [ 2.300773] scsi1 : ahci
    [ 2.301519] scsi2 : ahci
    [ 2.301793] scsi3 : ahci
    [ 2.301869] ata1: DUMMY
    [ 2.301872] ata2: DUMMY
    [ 2.301876] ata3: SATA max UDMA/133 abar m1024@0xd0445000 port 0xd0445200 irq 42
    [ 2.301878] ata4: DUMMY
    [ 2.301964] ata_piix 0000:00:1f.1: version 2.13
    [ 2.303447] scsi4 : ata_piix
    [ 2.303539] scsi5 : ata_piix
    [ 2.303600] ata5: PATA max UDMA/100 cmd 0x20d8 ctl 0x20f4 bmdma 0x20b0 irq 18
    [ 2.303603] ata6: PATA max UDMA/100 cmd 0x20d0 ctl 0x20f0 bmdma 0x20b8 irq 18
    [ 2.333409] firewire_ohci 0000:03:03.0: added OHCI v1.0 device as card 0, 8 IR + 8 IT contexts, quirks 0x0
    [ 2.473835] ata5.00: ATAPI: MATSHITADVD-R UJ-857E, ZB0E, max UDMA/66
    [ 2.487059] ata5.00: configured for UDMA/66
    [ 2.620034] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
    [ 2.620400] ata3.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out
    [ 2.620486] ata3.00: ATA-9: M4-CT256M4SSD2, 000F, max UDMA/100
    [ 2.620490] ata3.00: 500118192 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
    [ 2.620880] ata3.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out
    [ 2.620967] ata3.00: configured for UDMA/100
    [ 2.621138] scsi 2:0:0:0: Direct-Access ATA M4-CT256M4SSD2 000F PQ: 0 ANSI: 5
    [ 2.622978] scsi 4:0:0:0: CD-ROM MATSHITA DVD-R UJ-857E ZB0E PQ: 0 ANSI: 5
    [ 2.628440] sd 2:0:0:0: [sda] 500118192 512-byte logical blocks: (256 GB/238 GiB)
    [ 2.628549] sd 2:0:0:0: [sda] Write Protect is off
    [ 2.628553] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
    [ 2.628585] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    [ 2.629901] sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray
    [ 2.629904] cdrom: Uniform CD-ROM driver Revision: 3.20
    [ 2.630101] sr 4:0:0:0: Attached scsi CD-ROM sr0
    [ 2.630316] sda: sda1 sda2 sda3 sda4 sda5 sda6 sda7
    [ 2.631133] sd 2:0:0:0: [sda] Attached SCSI disk
    [ 2.681713] xor: measuring software checksum speed
    [ 2.713345] pIII_sse : 6420.000 MB/sec
    [ 2.746690] Switched to clocksource tsc
    [ 2.746718] prefetch64-sse: 7302.000 MB/sec
    [ 2.746721] xor: using function: prefetch64-sse (7302.000 MB/sec)
    [ 2.803340] raid6: mmxx1 2408 MB/s
    [ 2.833438] firewire_core 0000:03:03.0: created device fw0: GUID 001b63fffe882224, S400
    [ 2.853355] usb 1-4: new high-speed USB device number 3 using ehci-pci
    [ 2.860009] raid6: mmxx2 2773 MB/s
    [ 2.916671] raid6: sse1x1 1464 MB/s
    [ 2.973357] raid6: sse1x2 2019 MB/s
    [ 3.030025] raid6: sse2x1 2715 MB/s
    [ 3.086675] raid6: sse2x2 3448 MB/s
    [ 3.086678] raid6: using algorithm sse2x2 (3448 MB/s)
    [ 3.086680] raid6: using ssse3x1 recovery algorithm
    [ 3.093280] bio: create slab <bio-1> at 1
    [ 3.094419] Btrfs loaded
    [ 3.095092] btrfs: device label root devid 1 transid 4857 /dev/sda5
    [ 3.095774] btrfs: device label home devid 1 transid 199898 /dev/sda7
    [ 3.161953] btrfs: device label root devid 1 transid 4857 /dev/sda5
    [ 3.162678] btrfs: device label home devid 1 transid 199898 /dev/sda7
    [ 3.178283] btrfs: device label home devid 1 transid 199898 /dev/sda7
    [ 3.178935] btrfs: device label root devid 1 transid 4857 /dev/sda5
    [ 3.189620] btrfs: device label root devid 1 transid 4857 /dev/sda5
    [ 3.190409] btrfs: disk space caching is enabled
    [ 3.201691] Btrfs detected SSD devices, enabling SSD mode
    [ 3.573432] systemd[1]: systemd 212 running in system mode. (+PAM -AUDIT -SELINUX -IMA -SYSVINIT +LIBCRYPTSETUP +GCRYPT +ACL +XZ +SECCOMP -APPARMOR)
    [ 3.573617] systemd[1]: Detected architecture 'x86'.
    [ 3.574987] systemd[1]: Set hostname to <archbook>.
    [ 3.630096] systemd[1]: Cannot add dependency job for unit display-manager.service, ignoring: Unit display-manager.service failed to load: No such file or directory.
    [ 3.630650] systemd[1]: Starting Forward Password Requests to Wall Directory Watch.
    [ 3.630731] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
    [ 3.630747] systemd[1]: Starting Remote File Systems.
    [ 3.630908] systemd[1]: Reached target Remote File Systems.
    [ 3.630942] systemd[1]: Starting Arbitrary Executable File Formats File System Automount Point.
    [ 3.631207] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
    [ 3.631227] systemd[1]: Starting Encrypted Volumes.
    [ 3.631351] systemd[1]: Reached target Encrypted Volumes.
    [ 3.631373] systemd[1]: Starting Dispatch Password Requests to Console Directory Watch.
    [ 3.631421] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
    [ 3.631436] systemd[1]: Expecting device dev-sda6.device...
    [ 3.631545] systemd[1]: Expecting device dev-disk-by\x2duuid-5b847583\x2de4cb\x2d444d\x2dac05\x2db3ec8f1c77ff.device...
    [ 3.631698] systemd[1]: Expecting device dev-disk-by\x2duuid-462ff9d5\x2d22a9\x2d3b55\x2d9e3e\x2d39009d6be0b4.device...
    [ 3.631849] systemd[1]: Starting Root Slice.
    [ 3.643428] systemd[1]: Created slice Root Slice.
    [ 3.643446] systemd[1]: Starting Device-mapper event daemon FIFOs.
    [ 3.643611] systemd[1]: Listening on Device-mapper event daemon FIFOs.
    [ 3.643628] systemd[1]: Starting Delayed Shutdown Socket.
    [ 3.643774] systemd[1]: Listening on Delayed Shutdown Socket.
    [ 3.643790] systemd[1]: Starting /dev/initctl Compatibility Named Pipe.
    [ 3.643940] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
    [ 3.643955] systemd[1]: Starting LVM2 metadata daemon socket.
    [ 3.644108] systemd[1]: Listening on LVM2 metadata daemon socket.
    [ 3.644124] systemd[1]: Starting User and Session Slice.
    [ 3.644482] systemd[1]: Created slice User and Session Slice.
    [ 3.644503] systemd[1]: Starting udev Control Socket.
    [ 3.644646] systemd[1]: Listening on udev Control Socket.
    [ 3.644665] systemd[1]: Starting udev Kernel Socket.
    [ 3.644803] systemd[1]: Listening on udev Kernel Socket.
    [ 3.644820] systemd[1]: Starting Journal Socket.
    [ 3.644991] systemd[1]: Listening on Journal Socket.
    [ 3.645013] systemd[1]: Starting System Slice.
    [ 3.645365] systemd[1]: Created slice System Slice.
    [ 3.645389] systemd[1]: Starting Remount Root and Kernel File Systems...
    [ 3.646048] systemd[1]: Mounting Huge Pages File System...
    [ 3.646809] systemd[1]: Mounting POSIX Message Queue File System...
    [ 3.650099] systemd[1]: Starting Create list of required static device nodes for the current kernel...
    [ 3.651287] systemd[1]: Starting udev Coldplug all Devices...
    [ 3.657301] systemd[1]: Starting Load Kernel Modules...
    [ 3.658127] systemd[1]: Mounting Debug File System...
    [ 3.658754] systemd[1]: Starting Setup Virtual Console...
    [ 3.659815] systemd[1]: Starting Apply Kernel Variables...
    [ 3.660641] systemd[1]: Starting Set Up Additional Binary Formats...
    [ 3.661627] systemd[1]: Starting system-urxvtd.slice.
    [ 3.662195] systemd[1]: Created slice system-urxvtd.slice.
    [ 3.662227] systemd[1]: Starting system-getty.slice.
    [ 3.663290] systemd[1]: Created slice system-getty.slice.
    [ 3.663319] systemd[1]: Starting Journal Service...
    [ 3.664848] systemd[1]: Started Journal Service.
    [ 3.677214] btrfs: use lzo compression
    [ 3.677219] btrfs: use ssd allocation scheme
    [ 3.677226] btrfs: enabling auto defrag
    [ 3.677229] btrfs: enabling inode map caching
    [ 3.677231] btrfs: disk space caching is enabled
    [ 3.715284] vboxdrv: Found 2 processor cores.
    [ 3.716708] usb 2-2: new full-speed USB device number 2 using uhci_hcd
    [ 3.722186] vboxdrv: fAsync=0 offMin=0x3c2 offMax=0xda9
    [ 3.722268] vboxdrv: TSC mode is 'synchronous', kernel timer mode is 'normal'.
    [ 3.722268] vboxdrv: Successfully loaded version 4.3.10_OSE (interface 0x001a0007).
    [ 3.783071] vboxpci: IOMMU not found (not registered)
    [ 3.816344] systemd-udevd[167]: starting version 212
    [ 3.878200] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
    [ 3.881296] Monitor-Mwait will be used to enter C-1 state
    [ 3.881307] Monitor-Mwait will be used to enter C-2 state
    [ 3.881313] Monitor-Mwait will be used to enter C-3 state
    [ 3.881394] tsc: Marking TSC unstable due to TSC halts in idle
    [ 3.881443] ACPI: acpi_idle registered with cpuidle
    [ 3.882023] ACPI: AC Adapter [ADP1] (on-line)
    [ 3.882099] Switched to clocksource hpet
    [ 3.915143] snd_hda_intel 0000:00:1b.0: enabling device (0000 -> 0002)
    [ 3.915340] snd_hda_intel 0000:00:1b.0: irq 43 for MSI/MSI-X
    [ 3.956144] intel_rng: FWH not detected
    [ 3.983260] sky2: driver version 1.30
    [ 3.983769] sky2 0000:01:00.0: Yukon-2 EC chip revision 2
    [ 3.984190] sky2 0000:01:00.0: irq 44 for MSI/MSI-X
    [ 3.984693] sky2 0000:01:00.0 eth0: addr 00:19:e3:40:6b:e2
    [ 4.006473] input: HDA Intel SPDIF In as /devices/pci0000:00/0000:00:1b.0/sound/card0/input8
    [ 4.008040] ACPI: Battery Slot [BAT0] (battery present)
    [ 4.009840] input: HDA Intel Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input7
    [ 4.010988] input: HDA Intel Line as /devices/pci0000:00/0000:00:1b.0/sound/card0/input6
    [ 4.014099] input: HDA Intel Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input5
    [ 4.015212] ACPI Warning: 0x00000428-0x0000042f SystemIO conflicts with Region \PMIO 1 (20131115/utaddress-251)
    [ 4.015227] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
    [ 4.015235] ACPI Warning: 0x00000530-0x0000053f SystemIO conflicts with Region \GPIO 1 (20131115/utaddress-251)
    [ 4.015245] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
    [ 4.015249] ACPI Warning: 0x00000500-0x0000052f SystemIO conflicts with Region \GPIO 1 (20131115/utaddress-251)
    [ 4.015257] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
    [ 4.015261] lpc_ich: Resource conflict(s) found affecting gpio_ich
    [ 4.024430] cfg80211: Calling CRDA to update world regulatory domain
    [ 4.025189] leds_ss4200: no LED devices found
    [ 4.031105] i801_smbus 0000:00:1f.3: enabling device (0000 -> 0001)
    [ 4.031395] ACPI Warning: 0x0000efa0-0x0000efbf SystemIO conflicts with Region \_SB_.PCI0.SBUS.SMBI 1 (20131115/utaddress-251)
    [ 4.031408] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
    [ 4.066172] input: PC Speaker as /devices/platform/pcspkr/input/input9
    [ 4.082340] microcode: CPU0 sig=0x6f6, pf=0x20, revision=0xc7
    [ 4.083938] platform microcode: Direct firmware load failed with error -2
    [ 4.083946] platform microcode: Falling back to user helper
    [ 4.128874] btrfs: device label root devid 1 transid 4857 /dev/sda5
    [ 4.140066] usb 4-2: new full-speed USB device number 2 using uhci_hcd
    [ 4.145181] btrfs: device label home devid 1 transid 199898 /dev/sda7
    [ 4.161845] ath9k 0000:02:00.0: enabling device (0000 -> 0002)
    [ 4.180225] btrfs: device label home devid 1 transid 199898 /dev/sda7
    [ 4.181071] btrfs: use lzo compression
    [ 4.181079] btrfs: use ssd allocation scheme
    [ 4.181090] btrfs: enabling auto defrag
    [ 4.181096] btrfs: enabling inode map caching
    [ 4.181099] btrfs: disk space caching is enabled
    [ 4.234922] applesmc: key=226 fan=1 temp=10 index=10 acc=1 lux=0 kbd=0
    [ 4.247383] Adding 1048572k swap on /dev/sda6. Priority:-1 extents:1 across:1048572k SSFS
    [ 4.264911] hfsplus: Filesystem was not cleanly unmounted, running fsck.hfsplus is recommended. mounting read-only.
    [ 4.303293] input: applesmc as /devices/platform/applesmc.768/input/input10
    [ 4.316157] iTCO_vendor_support: vendor-support=0
    [ 4.318231] usb 1-4: Direct firmware load failed with error -2
    [ 4.318239] usb 1-4: Falling back to user helper
    [ 4.325798] microcode: CPU1 sig=0x6f6, pf=0x20, revision=0xc7
    [ 4.325836] platform microcode: Direct firmware load failed with error -2
    [ 4.325842] platform microcode: Falling back to user helper
    [ 4.352238] microcode: Microcode Update Driver: v2.00 <[email protected]>, Peter Oruba
    [ 4.362997] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.10
    [ 4.363053] iTCO_wdt: Found a ICH7-M or ICH7-U TCO device (Version=2, TCOBASE=0x0460)
    [ 4.371059] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
    [ 4.382811] Unable to load isight firmware
    [ 4.382874] usbcore: registered new interface driver isight_firmware
    [ 4.398462] random: nonblocking pool is initialized
    [ 4.408160] systemd-journald[146]: Received request to flush runtime journal from PID 1
    [ 4.451146] appletouch 2-2:1.1: Geyser mode initialized.
    [ 4.451279] input: appletouch as /devices/pci0000:00/0000:00:1d.0/usb2/2-2/2-2:1.1/input/input11
    [ 4.451581] usbcore: registered new interface driver appletouch
    [ 4.477422] hidraw: raw HID events driver (C) Jiri Kosina
    [ 4.505622] usbcore: registered new interface driver usbhid
    [ 4.505625] usbhid: USB HID core driver
    [ 4.511187] input: Apple Computer Apple Internal Keyboard / Trackpad as /devices/pci0000:00/0000:00:1d.0/usb2/2-2/2-2:1.0/input/input12
    [ 4.516069] apple 0003:05AC:021A.0001: input,hidraw0: USB HID v1.11 Keyboard [Apple Computer Apple Internal Keyboard / Trackpad] on usb-0000:00:1d.0-2/input0
    [ 4.516130] mousedev: PS/2 mouse device common for all mice
    [ 4.518122] input: Apple Computer Apple Internal Keyboard / Trackpad as /devices/pci0000:00/0000:00:1d.0/usb2/2-2/2-2:1.2/input/input13
    [ 4.520132] apple 0003:05AC:021A.0002: input,hidraw1: USB HID v1.11 Device [Apple Computer Apple Internal Keyboard / Trackpad] on usb-0000:00:1d.0-2/input2
    [ 4.526592] input: Apple Computer, Inc. IR Receiver as /devices/pci0000:00/0000:00:1d.2/usb4/4-2/4-2:1.0/input/input14
    [ 4.527505] appleir 0003:05AC:8240.0003: input,hiddev0,hidraw2: USB HID v1.11 Device [Apple Computer, Inc. IR Receiver] on usb-0000:00:1d.2-2/input0
    [ 4.544779] ath: EEPROM regdomain: 0x64
    [ 4.544782] ath: EEPROM indicates we should expect a direct regpair map
    [ 4.544785] ath: Country alpha2 being used: 00
    [ 4.544787] ath: Regpair used: 0x64
    [ 4.546745] usb 5-1: new full-speed USB device number 2 using uhci_hcd
    [ 4.555349] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
    [ 4.556184] ieee80211 phy0: Atheros AR5418 MAC/BB Rev:2 AR5133 RF Rev:81 mem=0xfbea0000, irq=17
    [ 4.290340] systemd-udevd[184]: renamed network interface eth0 to enp1s0
    [ 4.580350] systemd-udevd[176]: renamed network interface wlan0 to wls1
    [ 4.776795] input: HID 05ac:1000 as /devices/pci0000:00/0000:00:1d.3/usb5/5-1/5-1:1.0/input/input15
    [ 4.777809] hid-generic 0003:05AC:1000.0004: input,hidraw3: USB HID v1.11 Keyboard [HID 05ac:1000] on usb-0000:00:1d.3-1/input0
    [ 4.778302] input: HID 05ac:1000 as /devices/pci0000:00/0000:00:1d.3/usb5/5-1/5-1:1.1/input/input16
    [ 4.779613] hid-generic 0003:05AC:1000.0005: input,hidraw4: USB HID v1.11 Mouse [HID 05ac:1000] on usb-0000:00:1d.3-1/input1
    Any help would be appreciated.
    Last edited by bb010g (2014-04-03 19:07:54)

    It used to be in there (id 226635 is the last one with it); should I clean it up a bit and put it back with a bit more of a disclaimer?

  • Pdf content not loading while printing using JavaScript

    In my web app, I am trying to print a doc using JavaScript, but content of the pdf is not getting loaded, this can be seen in the below link.
    https://drive.google.com/file/d/0B2nqjT-VxFWwVVhsQ1hLUnJ3MFU/view?usp=sharing
    Code:
    var printWin = window.open(this.lURL, '', 'top=100, left=500, width=900, height=800, titlebar=no');
    printWin.print();
    "this.lURL" is link which brings the pdf file/doc.
    Note: As soon as I click on cancel button of print, the content gets loaded.
    And if I click print blank page gets printed.

    ''guigs2 [[#answer-708101|said]]''
    <blockquote>
    I understand that the web app that your are developing has a function to print the contents of a pdf created with javascript, :
    Please first check these basic troubleshooting steps for printing:
    *[[Fix printing problems in Firefox]]
    Does this happen with the default pdf viewer or another?
    Next also check with stackoverflow.com:
    [https://support.mozilla.org/en-US/kb/where-go-developer-support Where to go for developer support]
    </blockquote>
    I want a solution which doesn't require to reset or change the settings of the browser.
    Once the app is available globally everyone should be able to use this functionality without altering the settings of the browser.

  • Firmware not loading

    Well, its finally here! I did some basic stuff to insure all was well with my mac and here we go! Time for the Firmware update 4.2.8. Load, click, and then THIS! "The DOC "G4FWUP.bin" could not be opened, because the application program that created it could not be found. Do you want to open it with "SimpleText"?... AUGGGHHHH!!! So, anyway turn out I have OS 9.1.1. Cound this be the problem? Any and all help would be appreciated from this NOOB.
    Cheers,
    Chris

    Hi, PB -
    "Boot ROM Version $0004.13f2" translates to firmware v. 4.1.3, which is older than firmware v. 4.2.8.
    ASP's nomenclature leaves a bit to be desired. On my G4/500 (AGP) ASP states "Boot ROM Version $0004.18f5" which equals firmware v. 4.1.8 - I know this to be true because I installed the 4.1.8 update, but not yet the one for 4.2.8.
    The first firmware update for post-(PCI) G4s was 4.1.8. It was later replaced (superceded) by the 4.1.9 update, which did not live long - it was pulled when it became apparent it caused some audio-loss problems; very soon thereafter the 4.2.8 update came out. The 4.2.8 update will install on top of any previous firmware version on those machine models for which it is intended - the G4 (AGP), (GE), and (DA) models.

  • 32DV504B -TV Firmware not loading/showing on TV

    Hi all,
    I have downloaded the latest firmware upgrade for my TVs (x2) - 32DV504B. I have copied the downloaded file to a USB drive and plugged into the TV. I cannot seem to get the file loaded at all.
    I have tried numerous USB drives, numerous formats (FAT, FAT32 etc) - exe on it's own, extracted but no matter what I do I cannot get the upgrade done, I have tried to boot into the USB, I have tried the settings, search for upgrade - white bar just stays at zero saying searching.
    any help would be appreciated.
    Regards
    Barry

    Emmm….. I’m wondering where did find the firmware for this TV model... I checked the Toshiba download centre and this TV isn’t listed…
    I guess the firmware update cannot be performed because the firmware might not be fully compatible…

  • Intel iMac Firmware not loading

    I tried to install the new Intel iMac firmware so I can try out bootcamp. The firmware installer powers down fine and then I hold the power button and it flashes but then it gives a long tone and does not update the firmware but boots OSX back up again. What does this long tone mean? Why doesn't the firmware load? Do I have to keep holding the power down until the firmware progress bar starts or just until the power button flashes? The instructions seem to say hold down the power button until the power light flashes then it should load from there. But unfortunately it doesn't. I've reset the pram but that didn't help. Anyone have any ideas?
    Thanks.
    Intel iMac Dualcore 2GHZ   Mac OS X (10.4.6)  

    Firmware will not update if you installed the Windows hack. You will need to reformat and reinstall OSX 10.4.6 and then apply the firmware update. This fix was found by macfixit.com who had a macbook pro they had installed the windows hack on.
    Once the drive is setup normally with OSX the firmware will install.

  • HP Laserjet 6p is not recognized in Printer Setup Utility

    I bought recently used HP Laserjet 6p printer and connected my PB to it's Apple Talk port via AsanteTalk Box. After I installed the HP 6p printer driver (downloaded from the HP site) I've tried several times to find the printer in the Printer Setup Utility but it doesn't appear on it! I've even downloaded a printer driver for MacOS 9 and tried to print in Classic environment but can't find any HP printer in the Chooser. Is there any solution for this problem?
    I'll be very thankful for any suggestions.

    Apple included the Gimp-Print driver "HP Laserjet 6 Series" for that printer. Does that show up?

  • Can not load HP Print APP onto iPad 1 with 5.1.1 OS.

    All the HP Printa Apps want OS 6.0, and I have an iPad with OS 5.1.1

    Hello gstuck,
    Welcome to the HP Support Forums!
    Since the iPad 1 is only compatible with the iOS 5.1.1 you have installed, unfortunately, you can not install the HP ePrint App.
    What model of printer are you trying to print with from the iPad?
    Regards,
    JERENDS
    I work on behalf of HP
    Please click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos Thumbs Up" to the left of the reply button to say “Thanks” for helping!

  • [SOLVED] Wireless configuration: firmware not loaded?

    Dear all,
    I would like to configure my Wifi schede in my Arch installation.
    I started following the guide in the wiki (https://wiki.archlinux.org/index.php/Wi … figuration)
    but I get to a point where I have an error but don't know how to proceed.
    Following the guide I did:
    lspci -k
    02:00.0 Network controller: Qualcomm Atheros AR9485 Wireless Network Adapter (rev 01)
    Subsystem: Samsung Electronics Co Ltd Device 4105
    Kernel driver in use: ath9k
    Kernel modules: ath9k
    So that it seems that the driver for my card is installed and in use.
    Next I did:
    ip link
    1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN mode DEFAULT group default
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    2: enp1s0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc pfifo_fast state DOWN mode DEFAULT group default qlen 1000
    link/ether 20:89:84:0f:7d:91 brd ff:ff:ff:ff:ff:ff
    3: wlp2s0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state DOWN mode DEFAULT group default qlen 1000
    link/ether 50:b7:c3:24:85:c1 brd ff:ff:ff:ff:ff:ff
    From the output I deduce that wlp2s0 is the name of my interface, so I try to turn on the interface:
    ip link set wlp2s0 up
    ##NO OUTPUT IS DISPLAYED##
    Next I do:
    dmesg | grep firmware
    [ 11.882857] platform microcode: Direct firmware load failed with error -2
    [ 12.143983] platform microcode: Direct firmware load failed with error -2
    [ 12.148247] platform microcode: Direct firmware load failed with error -2
    [ 12.148586] platform microcode: Direct firmware load failed with error -2
    dmesg | grep ath9k
    [ 1781.365268] Loading kernel module for a network device with CAP_SYS_MODULE (deprecated). Use CAP_NET_ADMIN and alias netdev-ath9k instead.
    I have no idea what I have to do at this point. How do I enable my wifi card and manage my network (possibly with some graphic tools for my MATE desktop)
    Thanks a lot in advance for the help!
    Cheers,
    Luca
    Last edited by lucacerone (2014-03-29 12:07:29)

    Hi, I managed to use my wifi using NetworkManager.
    In the wiki it says that I have to be sure no other service that wants to configure the network is running.
    Everything seems to work fine now, but can you pleas check my output of "systemctl --type=service" and
    let me know if I need to disable any service?
    systemctl --type=service
    UNIT LOAD ACTIVE SUB DESCRIPTION
    dbus.service loaded active running D-Bus System Message Bus
    dhcpcd.service loaded active running dhcpcd on all interfaces
    kmod-static-nodes.service loaded active exited Create list of required static device nodes for the current kernel
    lightdm.service loaded active running Light Display Manager
    polkit.service loaded active running Authorization Manager
    rtkit-daemon.service loaded active running RealtimeKit Scheduling Policy Service
    systemd-backlight@backlight:acpi_video0.service loaded active exited Load/Save Screen Backlight Brightness of backlight:acpi_video0
    systemd-backlight@backlight:intel_backlight.service loaded active exited Load/Save Screen Backlight Brightness of backlight:intel_backlight
    systemd-hostnamed.service loaded active running Hostname Service
    systemd-journald.service loaded active running Journal Service
    systemd-logind.service loaded active running Login Service
    systemd-random-seed.service loaded active exited Load/Save Random Seed
    systemd-remount-fs.service loaded active exited Remount Root and Kernel File Systems
    [email protected] loaded active exited Load/Save RF Kill Switch Status of rfkill0
    [email protected] loaded active exited Load/Save RF Kill Switch Status of rfkill1
    [email protected] loaded active exited Load/Save RF Kill Switch Status of rfkill2
    [email protected] loaded active exited Load/Save RF Kill Switch Status of rfkill3
    systemd-sysctl.service loaded active exited Apply Kernel Variables
    systemd-tmpfiles-setup-dev.service loaded active exited Create Static Device Nodes in /dev
    systemd-tmpfiles-setup.service loaded active exited Create Volatile Files and Directories
    systemd-udev-trigger.service loaded active exited udev Coldplug all Devices
    systemd-udevd.service loaded active running udev Kernel Device Manager
    systemd-update-utmp.service loaded active exited Update UTMP about System Boot/Shutdown
    systemd-user-sessions.service loaded active exited Permit User Sessions
    systemd-vconsole-setup.service loaded active exited Setup Virtual Console
    udisks2.service loaded active running Disk Manager
    upower.service loaded active running Daemon for power management
    [email protected] loaded active running User Manager for UID 1000
    wpa_supplicant.service loaded active running WPA supplicant
    LOAD = Reflects whether the unit definition was properly loaded.
    ACTIVE = The high-level unit activation state, i.e. generalization of SUB.
    SUB = The low-level unit activation state, values depend on unit type.
    29 loaded units listed. Pass --all to see loaded but inactive units, too.
    To show all installed unit files use 'systemctl list-unit-files'.

  • HP LaserJet M2727nf

    I have recently purchased a Laserjet M2727nf. I need this printer to function as a network device only, since there are no PCs with 20 meters.
    How do I configure faxing from this device so that I can operate with the Scan To button? I read an article that said this was not possible?
    Can I scan to email over the network?
    Can I scan to a network shared over the network?
    What are the disadvantages of not having USB conectivity?

    The scan to device is ment to be used to scan on the Printer and send it to a particular PC buy setting up the printer to know your computer name,thats how it tells one computer from another becuase it couldn't do it with ip addresses because  DHCP ip assignment always changes the address. You should have a fax setup in the start menu in the printer folder,it should have configured that when you installed the software on the pc but you can do it yet.And it must be done on every pc.I don't know about scanning to a network share.This printer was designed to be a part of the network attached by ethernet not to do that is to hamper the full use of it.
                                           Donovan Hulbert

Maybe you are looking for

  • Issues with windows 7 ram on a gd65 mobo

    Hi all, i recently upgraded my pc after my old asus mobo died on me.  I found a good deal with a gd65, i5 750, and 4 x2 gigs of ram on newegg as a package deal.  I was looking around on windows and it says i have 8 gigs of ram but only 2.99 is availa

  • How do you connect printer to the iPad?

    How do you connect printer to ur I pad?

  • IPhone app (shapewriter) is corrupted. App's no longer in the Store. How can I restore from my backup?

    An iPhone app that I love has become corrupted. This app is no longer available in the Store. Can I restore the app from my phone backup? How? Anything to watch out for? Shapewriter was purchased by Nuance. As most Dragon users will tell you, Nuance

  • Photos showing in camera roll but unable to view ;(

    Hey guys and girlys, i really hope you might be able to help me out with this, as above ive got a bunch of photos in my camer roll, but when i click on one of them i get a black screen with a white dot in the middle?? all 263 photos are doing the sam

  • Cannot start Web Client

    Hi, I recently installed Oracle Hyperion Data Relationship Management, Fusion Edition. Ive created a new application and repository using the management console succesfully, however when I try to run the Web Client, I get: --------===================