Hsrp problem....hsrp address not responding

Hi
I'm hoping I can get some opinions on this. I have 2 7200 routers with 2 gig interfaces each. Each gig interface is connected to 2 stacked 3750 switches. I have sub interfaces configured on both the gig interfaces so they are essentially dot1q to the 3750 switches. I have specified a hsrp group for each subinterface on the 7200s. My problem is that when I have 1 of the 7200 routers acting as hsrp active for some groups and the other 7200 acting as hsrp active for other groups hosts lose connectivity to their hsrp address for one of the routers. i.e no response to pings yet correct mac address in arp table.All works well when I make either one of the routers the hsrp active for all of the groups. Any ideas?
r1----3750----hosts
\/ | <--stack
/\ |
r2----3750----hosts

config for one router is below.The other router is the same apart from the track command and the priority is 155. The 2 3750s have the vlans configured and dot1q trunks to both of the routers 2 gig ports.
the show standby at the moment shows the correct info ie the correct router is active for all the groups...
thanks
interface GigabitEthernet0/1
description *** Primary link to Switch 1 ***
no ip address
no ip proxy-arp
duplex auto
speed auto
media-type sfp
negotiation auto
interface GigabitEthernet0/1.10
encapsulation dot1Q 10
ip address x.x.x.x 255.255.255.224
no ip proxy-arp
no snmp trap link-status
standby 10 ip x.x.x.x
standby 10 priority 160
standby 10 preempt delay minimum 60
standby 10 track GigabitEthernet1/0
interface GigabitEthernet0/1.30
encapsulation dot1Q 30
ip address x.x.x.x 255.255.255.192
no ip proxy-arp
no snmp trap link-status
standby 30 ip x.x.x.x
standby 30 priority 160
standby 30 preempt delay minimum 60
standby 30 track GigabitEthernet1/0
interface GigabitEthernet0/1.70
encapsulation dot1Q 70
ip address x.x.x.x 255.255.255.252
no ip proxy-arp
no snmp trap link-status
interface FastEthernet0/2
no ip address
shutdown
duplex auto
speed auto
interface GigabitEthernet0/2
description **** secondary link to switch 2 ***
no ip address
no ip proxy-arp
duplex auto
speed auto
media-type sfp
negotiation auto
interface GigabitEthernet0/2.20
encapsulation dot1Q 20
ip address x.x.x.x 255.255.255.224
no ip proxy-arp
ip ospf network broadcast
no snmp trap link-status
standby 20 ip x.x.x.x
standby 20 priority 160
standby 20 preempt delay minimum 60
standby 20 track GigabitEthernet1/0
interface GigabitEthernet0/2.40
description *** N2 Web Farm ***
encapsulation dot1Q 40
ip address x.x.x.x 255.255.255.192
no ip proxy-arp
no snmp trap link-status
standby 40 ip x.x.x.x
standby 40 priority 160
standby 40 preempt delay minimum 60
standby 40 track GigabitEthernet1/0
interface GigabitEthernet0/2.50
encapsulation dot1Q 50
ip address x.x.x.x 255.255.255.240
no ip proxy-arp
no snmp trap link-status
standby 50 ip x.x.x.x
standby 50 priority 160
standby 50 preempt delay minimum 60
standby 50 track GigabitEthernet1/0
interface GigabitEthernet0/2.80
encapsulation dot1Q 80
ip address x.x.x.x 255.255.255.252
no ip proxy-arp
ip ospf network broadcast
no snmp trap link-status

Similar Messages

  • I have ongoing problems with "application not responding" in various programmes, ie Word, Excel, Illustrator, Photoshop, iPhoto etc. I recently subscribed to CC but the problem still persists. Any advice please?

    I have ongoing problems with "application not responding" in various programmes, ie Word, Excel, Illustrator, Photoshop, iPhoto etc. I recently subscribed to CC but the problem still persists. Any advice please? This applies to my iMac and my macbook air! I'm using OSX Version 10.9.3

    Hi Shauneenb,
    Welcome to the Apple Support Communities!
    If you are having issues with multiple applications becoming unresponsive I would suggest the steps in the following article, including starting in safe mode.
    OS X Mavericks: If an app freezes or quits unexpectedly
    http://support.apple.com/kb/PH13975
    I hope this helps,   
    -Joe

  • Problems with IE8 "not responding" on windows 7

    I have a Toshiba Satellite L-355  that has been upgraded to run Windows 7 Home Premium from Windows Vista. I've been having problems with IE8 "not responding" and have tried running it without add-ons, system restore, and banging my head against the wall. All to no avail. Does anybody have any ideas how to fix this? I've tried running other browsers with the same problems.

    Intel(R) HM55 Express Chipset LPC Interface Controller
    Thanks, sav! That's perfect. (Good to know it shows up in Device Manager for people, too.)
    Okay ... although it's the Intel P55 and PM55 chipsets which get all the press about cranky Touch/iPhone connections on Windows 7 systems (the 0xE0000065, -6999 and "Disk can not be read or written to" error messages are the most common, although symptoms can vary further than that), similar sorts of issues look like they could strike other Intel 5-series chipsets ... including your HM55.
    So I'm proceeding precisely as I would with someone with a PM55 chipset.
    *1) Dell updates*
    Some folks with 5-series chipset trouble have got past it by way of BIOS updates. So I thinks it's worth your heading to your Downloads page at Dell, and checking to see if there's any newer versions of your BIOS lurking there. Unfortunately, with the Studio 15s I'm never precisely sure which is the correct downloads page ... so I'd try going to the following Dell page:
    http://support.dell.com/support/downloads/index.aspx
    ... enter your service tag, and then drill through to your downloads page.
    Any improvement with your syncing performance after applying any available BIOS updates at Dell?
    *(2) Adjust power management setting on USB controllers*
    If no joy after updating (if you were behind on your BIOS version), try applying the measures from the following document:
    [iPod not recognized when connected to Windows laptop over USB|iPod not recognized when connected to Windows laptop over USB]
    Reboot the PC after making the changes, and then try another sync. Any improvement?
    (If either set of measures improves your sync performance, please post back to let us know which one helped for you.)

  • Mail Problems - SMTP server not responding: "offline"

    I am currently testing DSL service for a month; set up Mail just before I downloaded the 10.7.3 release. Tested it once and it worked; did not use it to send emails since because I am only testing this (including the email address). I have been receiving emails (which I forwarded to myself from my cable provider's website); today, I wanted to send an email and a 6 hour troubleshooting saga began....
    Total of 2 hours with Centurylink tech support; 1 1/2 hours with Applecare, and another 30 minutes with Centurylink.
    During that time, all different settings were tried, turned on/off. POP server ok, SMTP server not responding. With Applecare, tried it on both the iMac and the Macbook; also tried it after booting into Snow Leopard - SMTP server not responding ("offline"). Applecare tech stated that it has to be the server since we tried it on two machines as well as SL. Centurylink insists there is nothing wrong with their server, but it's Mail's fault.
    So, I finally gave up for the evening, but wonder if there is something amiss with Mail in 10.7.3 (both machines are on the same version) and during the troubleshooting, I noticed an anomaly: in a new message window, there was no choice to choose an account to send from which I thought was odd.
    I was thinking of a new install or to clone back? My clones are up to date though, I have no older clones. I do have a fresh install but it's also the latest one from MAS. Or I could just boot from the fresh install and set up Mail to see if it would work?
    Grateful for any ideas....

    Thanks to everyone; as you can imagine, all settings/configurations were tried yesterday (even booting into SL); Apple said it's Centurylink's fault, and they insisted there was nothing wrong with their server.
    FWIW, I unplugged my Comcast cable (it is still active though and I'm getting TV reception, just unplugged the modem for now); right now, my internet access and email account are with Centurylink for the test. I still access my Comcast mail via their web interface email account.
    Anyway, thanks to a good friend's idea, I decided to check keychain access and to make it short: the issue is fixed and the problem definitely had something to do with the OS because:
    When I first checked keychain, this is what I saw:
    I then checked Comcast settings and there were two: one was checked "allow all apps..." and the other had the "confirm" with Mail listed under the applications.
    So I figured it's so screwed up, I probably can't make it any worse, so I deleted the Internet Accounts and added Mail to the smtp.centurylink...:
    And......... it then worked! These default "internetaccounts" obviously aren't being recognized by Centurylink's server?
    And, to make sure that was it, I not only did the same thing on the Macbook, but also booted into a pristine "backup" fresh install (no added apps or files, just default OS), launched Mail and couldn't send. Launched Keychain, changed the apps to Mail, and I was able to send email.
    I would call that a bug? Or not? In any case, I'll be calling back Applecare and tell them to add the above to the very long log from yesterday and to make a note that "internetaccounts" doesn't work with everything.

  • Touchpad touchscreen problems (erratic behavior/not responding correctly/etc) temporary solution.

    I bought a HP Touchpad about a month or two after it came out. It worked pretty much as you'd expect it to until some time ago. I started getting a problem where the screen would go crazy and not respond correctly to my touch inputs. Web pages would jump all over the place, cards would zoom out, etc, in other words, they would behave erratically. After some testing I noticed that certain areas  of the touchscreen would NOT respond at all to inputs while others would make the screen go crazy like I mentioned previously. I looked for information on the web to see if other people where having the same problem and found reports of the same behavior. Unfortunately there where no solutions offered. At that point I tried turning on and off the Touchpad which did not resolve the problem. My next step was to try to reinstall the OS with WebOS Doctor, but I read a post where the user reported similar behavior and reinstalling with WebOS Doctor didn't fix the problem. Needless to say I was bummed out since I figured it was a hardware problem with the touchscreen. After more testing I found a temporary solution to the problem which seems to suggest that the probem could be software. The solution when you get the problem is to hold down the power button and the home button at the same time and keep them pressed until the screen shuts down and the touchpad restarts. Once the OS comes back up it works like it is supposed to until you get the next episode of screen epilepsy. At that point you need to do the procedure again and it will fix the problem temporarily. Usually the fix lasts for a few days in my case. The fix also solves other problems I have with the touchpad. Problems like, videos not playing fluidly or freezing every few seconds although the sound plays fine (youtube), sound gets messed up (sounds are played in a robot like pitch), and others. If anybody has questions or other suggestions let me know, I will answer the as best as I can.
    Post relates to: HP TouchPad (WiFi)

    I think the YouTube and sound problems are separate from the other erratic behaviour.  Recently my touchpad won't play YouTube videos beyond certain points, starting a few seconds in possibly due to the advertising pop-ups - I can skip forwards, but that means I miss crucial parts.  My sound also goes 'robot-like' until a reboot, which is incredibly annoying!  Your touchscreen problems may be specific to your device - try going to Device Info / Diagnostics and see if that tells you anything.

  • "Insufficient Bandwidth Problem" and "Did not respond" error messages

    I am getting 3 error messages when I try to video chat using isight and ichat with my son's PC (which does video chat with my husband's PC) I have not been able to video chat although I can instant message with my son's PC.
    1. It says insufficient bandwidth"
    2. It says "starting" for a LONG time, and never finishes.
    3. Or they request a chat with me and I get a "Did not respond" message.
    I have tried connecting with both my .mac account and my aim name inside of iChat
    So far, I have:
    1. Changed Quicktime streaming to 1mbps Cable
    2. Reinstalled Quicktime 7.0.1, erasing 7.0.3
    3. Made an ichat AV entry under Firewall, listing TCP etc ports for network entry, using numbers from previous posts
    4. Firewall is off
    Since video chat works between my son's computer and my husband's, I doubt that it is our cable company or my son's. My son can also video chat with friends in his area. They are using msn or aim. However I have not been able to establish a connection using ichat.
    If there are no other fixes, then I will probably have to call Apple tomorrow for a return on the isight that I just purchased. Too bad, because the Los Angeles Times this morning said that iChatAV image quality is superior to even Skype's new product 2.0 for Windows. At this time Skype does not have a cross platform product. Is that the problem with iChatAV, it really only works with other Macs?
    Please advise if there is anything else that I can do to correct the problem. I have used an apple computer for more than 20 years, since the first little Apple IIc that I had. This is the first thing that I haven't been able to figure out.
    Thank you,
    Linda

    HI,
    This
    1. It says insufficient bandwidth"
    2. It says "starting" for a LONG time, and never finishes.
    3. Or they request a chat with me and I get a "Did not respond" message.
    Normally implies the ports are not open some where.
    The bit I have changed to Bold is not specific enough
    I have tried connecting with both my .mac account and my aim name inside of iChat
    So far, I have:
    1. Changed Quicktime streaming to 1mbps Cable
    2. Reinstalled Quicktime 7.0.1, erasing 7.0.3
    3. Made an ichat AV entry under Firewall, listing TCP etc ports for network entry, using numbers from previous posts
    4. Firewall is off
    Can you tell us exactly which ports you have opened and which protocols. APple Doc 93208 is Wrong.
    1. All iChat AV traffic is UDP except for ports 5190 and 5298, which need to be open for both TCP and UDP; and 5220, 5222, and 16384-16403, which need to be open for TCP only.
    You have not siad what ports you have opened and by what method in your modem ?
    Ralph

  • I am getting problems with Firefox not responding and it takes several tries to get to where I want. What causes this?

    When I log onto the internet I am now using Google as my home page but my problem still exists. When I go to get a new site I get a message that Firefox is not responding. Then it clears up and I click on something else and it does the same thing. I have even done a complete virus and malware check on my computer. What can I do to correct this?

    Please read this thread:
    http://support.mozilla.com/bs/questions/797708

  • I have upgraded twice to FF 4.0 and both times I have had major problems with it not responding and loading pages very slowly.

    I have once again gone back to the older 3.6 version. I love the layout of the new 4.0, but I hate all the lagtime and the fact that it stops responding every few minutes. Will this be addressed? I would much rather have the latest version, but the lags are annoying.

    I have also updated to the newest version and enjoyed the new look and layout how ever I have experienced confusing issues. For a few months 4.0 ran without a hitch no problem in sight then all of a sudden each time I loaded any link I would experience no indication of it working. Loading up task manager it was running at least twice at demanding memory usage was also high. The cpu usage was just as it always was which was below 5% even with other programs running. It constantly shows that the browser is "(not responsive)"

  • Problems with itunes7 not responding once ipod recognised

    hi i need help ihave downloaded itunes7 unfortunatley!!
    itunes works when my 4th gen 40g ipod with click wheel not connected.
    when i connect the ipod it is recognised and all the nifo comes up but within a matter of time when is appears to be updating then itunes stops responding.
    having looked up on this site and in support etc i have done the following
    1 uninstalled itunes completely including emptying temp file
    2 installing quick time separately
    3 reinstalling itunes
    problem still persists
    then tried
    uninstalling again and reinstalling without my antivirus software enabled
    problem still persists
    i have checked that the ipod is listed in services and it is
    i still have itunes6 installer but it cannot install as it cannot read the file
    does anyone have any suggestions
    thanks

    thankyou i have managed to revert back to itunes 6 but unfortunately now my ipod is not coming up within it.
    i have tried to revert back to a previous ipod software as i think that it software for the ipod was poss updated
    do you know of anything that i can do or is it just sit and wait until a newer version of itunes comes out
    thanks

  • I updated to Firefox 5 and now have problems with it not responding ALOT and also even though I have certian sites listed to allow popups they dont work on several sites I use daily. What can I do about this?

    I dont know what else to say about it. I updated and now all this is happening and it didnt before my update to Firefox5. I have several site I use daily and I have gone in and marked them to allow popups and they just dont work. The sites are My Yearbook...Kia Financeing...and a few more. And also I am finding that I get a no response a lot!

    I am sorry you are not in a position to replace the iPad. It is stating the obvious, but nothing lasts forever - especially something like an original iPad. IMHO, there is nothing you can do to address the issues you have posted about.
    Barry

  • Spaces problem: mouse clicks not responding

    Since upgrading to 10.5.3 I have a recurring problem where after changing screens in Spaces my mouse no longer accepts clicks. I can move the mouse normally, but when I click there is no response and I hear the error alert sound as if the mouse were disabled by an alert or something similar. The only way to get back to normal is to reboot.
    This happens with both my wireless mouse and with the USB mouse so I don't think it's hardware related. I've tried force quitting all open applications and restarting the Finder to no avail. It has happened during operation of several different apps so it's not related to any specific application software. I tried disabling any non-apple pref panes as well.
    Anybody got any hints? I'd hate to give up Spaces, I've grown accustomed to it's interface.

    I have a similar problem, not exactly the same.
    I can switch screens just fine all day long. My weird mouse behavior comes from dragging an application from one space to another. I use a secondary monitor and after I get "locked out", I am only "locked out" from my main monitor. On my secondary monitor, I can continue to click applications and interact with them. On the primary monitor (MBP screen), Any application I click on actually loses focus. Similarly I can move the mouse over items in the dock, and they expand/shrink, but I cannot click on any of them.
    In no case have I heard an alert to suggest that the mouse has been disabled though.
    I have corrected this only by restarting.
    I hope this gets fixed. I hadn't noticed it before about 2 or 3 weeks ago, but it has happened to me twice within the last 2 days and once before that about a week ago(?).
    -Andy

  • Broadband connection problems - IP4V address not m...

    After 2 telphone calls to tech help & 1 very loooong online chat I'm no further forward to solving my problem - so hoping that somebody here can assist please. I only returned to BT last month and one  PC that is connected to home hub via TP Link AV500 powerline will work for a day or so and then randomly disconnects and is very hard to get reconnected again (usually invlves resetting home hub & powerline + much switching on /off) Took 3 hours today to reconnect. It transpires that the IP address on the PC is different to the BT one & nobody so far has shed any light on how I can put this right. Have been through a number of basic diagnostics with the BT tech helpline ie: disabling/enabling settings etc but no joy. If any one can help please that'd be fab. 

    Do you mean the local (LAN) address on the PC is different?
    Have you set up your PC with a fixed address on the LAN (in network configuration) rather than with DHCP?
    That could be what is causing confusion; especially if the fixed address is one that can also be allocated as a dynamic address by the HomeHub.
    Most powerline adaptors just act as switches and don't have any extra routing capabilities (such as NAT or DHCP).  If your powerline does have such options try turning them off and leaving all the address details to the HomeHub.

  • Vip address not responding

    I am testing our new CSS 11501s (which are going to replace our old LocalDirectors), and have setup a little lab like so:
    Test PC
    |
    Router
    |
    | e5
    CSS
    e1 e2
    | |
    Srv1 Srv2
    I cannot seem to get the configured vip addreses to work, however I can connect to the actual webserver ips on port 80 (which are directly connected to ports 1 & 2). Any idea why it is not working?
    Here is my config:
    interface e1
    bridge vlan 100
    interface e2
    bridge vlan 200
    interface e5
    trunk
    vlan 100
    vlan 200
    circuit VLAN100
    ip address 10.10.100.100 255.255.255.0
    circuit VLAN200
    ip address 10.10.200.100 255.255.255.0
    service www_eth0
    ip address 10.10.100.2
    keepalive type http
    active
    service www_eth1
    ip address 10.10.200.2
    keepalive type http
    active
    owner webowner
    content eth0
    port 80
    protocol tcp
    add service www_eth0
    vip address 10.10.100.25
    active
    content eth1
    protocol tcp
    port 80
    add service www_eth1
    vip address 10.10.200.25
    active

    I think you get no response from the vip because you have no default route on the CSS pointing at your router.
    If you do have a default route, capture a 'show summary' and 'sho service summary' to verify that the content rules are active.
    Regards,
    Gilles.

  • Itunes just asked me to do another update yesterday. But it's still not working. when ever i try to sync music to my ipod touch it keeps saying itunes is not responding and it freezes. Itunes please fix this problem!!!!!:-(

    Itunes still is not working correctly. There was a software update that i received yesterday and i figured it would fix the problem with itunes not responding, but it didn't. It's still doing the same thing. I'm getting kinda annoyed cause i use itunes as my main music player so please help me fix this software issue thanks!

    Hi Batman1981,
    It sounds like you may be describing an issue where a program that monitors the Winsock protocol for Windows is conflicting with iTunes and it's related components. Take a look at the article linked below, it provides suggestions that may resolve the issue.
    Apple software on Windows: May see performance issues and blank iTunes Store
    http://support.apple.com/kb/ts4123
    You may notice the following symptoms on your Windows PC after installing the iCloud Control Panel, iTunes 10.5 or later, or Safari 5.1 or later:
    iTunes is slow to respond.
    Windows is slow to respond.
    iTunes stops responding when backing up or syncing with an iPhone, iPad, or iPod touch.
    -Jason

  • Why does my Mozilla Firefox 6.02 hang every few minutes. Its has been going on for years. "Not Responding" you can close and reopen and its fine, or wait 30 seconds and it goes back to normal, others like MSN, Opera, Chrome not having this problem.

    Oh and before I get disable your add ons, update and any other Generic crap. I did. ALL of that. Deleted Firefox completely then reinstalled it. Still the same error, my laptop in my office no problems my desktop "Not responding" wow.

    Switched to chrome on that computer. Seems to be the only solution that works. Mozilla, I know you are a good browser, I have sung your praises for years. But if you need to do all that technical stuff to get it to stop. Its really easier just to download another browser. Sorry. If you get your glitched corrected, I would be happy to come back. But I'm sorry I don't have that much time to waste.

Maybe you are looking for