Vip address not responding

I am testing our new CSS 11501s (which are going to replace our old LocalDirectors), and have setup a little lab like so:
Test PC
|
Router
|
| e5
CSS
e1 e2
| |
Srv1 Srv2
I cannot seem to get the configured vip addreses to work, however I can connect to the actual webserver ips on port 80 (which are directly connected to ports 1 & 2). Any idea why it is not working?
Here is my config:
interface e1
bridge vlan 100
interface e2
bridge vlan 200
interface e5
trunk
vlan 100
vlan 200
circuit VLAN100
ip address 10.10.100.100 255.255.255.0
circuit VLAN200
ip address 10.10.200.100 255.255.255.0
service www_eth0
ip address 10.10.100.2
keepalive type http
active
service www_eth1
ip address 10.10.200.2
keepalive type http
active
owner webowner
content eth0
port 80
protocol tcp
add service www_eth0
vip address 10.10.100.25
active
content eth1
protocol tcp
port 80
add service www_eth1
vip address 10.10.200.25
active

I think you get no response from the vip because you have no default route on the CSS pointing at your router.
If you do have a default route, capture a 'show summary' and 'sho service summary' to verify that the content rules are active.
Regards,
Gilles.

Similar Messages

VIP is not responding When pinging from ace

hey i have a very strange type of error. everything was working fine untill it just stopped. i have two vips both were mounted and working fine and then one of the vip just stopped working you can ping and get reply from my pc but not from ace. they are connected directly with nexus 5k and was working fine. now you can have reply from for other vips and servers and all other thing but not that single vip. when you ping it on nexus you get DUP; Packets which is not understood by me there is all commands like no ip redirects are been given but i dont know wats rong.
can some1 have any idea and help ?

Hi Usman,
Not sure about DUP packets that you see on nexus but from ACE's perspective we need to see what is wrong and for that i would need to look at your configuration and other outputs. Do you see that your client's request is reaching the ACE VIP ? You can check using "show conn address " and see if you see a corresponding backend connection or not. Do you see any handshake failures or any other counters increasing under "show stats crypto server" command? We need to have more information for us to look at to tell you what is going on at least from ACE's viewpoint.
Regards,
Kanwal

Hsrp problem....hsrp address not responding

Hi
I'm hoping I can get some opinions on this. I have 2 7200 routers with 2 gig interfaces each. Each gig interface is connected to 2 stacked 3750 switches. I have sub interfaces configured on both the gig interfaces so they are essentially dot1q to the 3750 switches. I have specified a hsrp group for each subinterface on the 7200s. My problem is that when I have 1 of the 7200 routers acting as hsrp active for some groups and the other 7200 acting as hsrp active for other groups hosts lose connectivity to their hsrp address for one of the routers. i.e no response to pings yet correct mac address in arp table.All works well when I make either one of the routers the hsrp active for all of the groups. Any ideas?
r1----3750----hosts
\/ | <--stack
/\ |
r2----3750----hosts

config for one router is below.The other router is the same apart from the track command and the priority is 155. The 2 3750s have the vlans configured and dot1q trunks to both of the routers 2 gig ports.
the show standby at the moment shows the correct info ie the correct router is active for all the groups...
thanks
interface GigabitEthernet0/1
description *** Primary link to Switch 1 ***
no ip address
no ip proxy-arp
duplex auto
speed auto
media-type sfp
negotiation auto
interface GigabitEthernet0/1.10
encapsulation dot1Q 10
ip address x.x.x.x 255.255.255.224
no ip proxy-arp
no snmp trap link-status
standby 10 ip x.x.x.x
standby 10 priority 160
standby 10 preempt delay minimum 60
standby 10 track GigabitEthernet1/0
interface GigabitEthernet0/1.30
encapsulation dot1Q 30
ip address x.x.x.x 255.255.255.192
no ip proxy-arp
no snmp trap link-status
standby 30 ip x.x.x.x
standby 30 priority 160
standby 30 preempt delay minimum 60
standby 30 track GigabitEthernet1/0
interface GigabitEthernet0/1.70
encapsulation dot1Q 70
ip address x.x.x.x 255.255.255.252
no ip proxy-arp
no snmp trap link-status
interface FastEthernet0/2
no ip address
shutdown
duplex auto
speed auto
interface GigabitEthernet0/2
description **** secondary link to switch 2 ***
no ip address
no ip proxy-arp
duplex auto
speed auto
media-type sfp
negotiation auto
interface GigabitEthernet0/2.20
encapsulation dot1Q 20
ip address x.x.x.x 255.255.255.224
no ip proxy-arp
ip ospf network broadcast
no snmp trap link-status
standby 20 ip x.x.x.x
standby 20 priority 160
standby 20 preempt delay minimum 60
standby 20 track GigabitEthernet1/0
interface GigabitEthernet0/2.40
description *** N2 Web Farm ***
encapsulation dot1Q 40
ip address x.x.x.x 255.255.255.192
no ip proxy-arp
no snmp trap link-status
standby 40 ip x.x.x.x
standby 40 priority 160
standby 40 preempt delay minimum 60
standby 40 track GigabitEthernet1/0
interface GigabitEthernet0/2.50
encapsulation dot1Q 50
ip address x.x.x.x 255.255.255.240
no ip proxy-arp
no snmp trap link-status
standby 50 ip x.x.x.x
standby 50 priority 160
standby 50 preempt delay minimum 60
standby 50 track GigabitEthernet1/0
interface GigabitEthernet0/2.80
encapsulation dot1Q 80
ip address x.x.x.x 255.255.255.252
no ip proxy-arp
ip ospf network broadcast
no snmp trap link-status

I am getting "dns server not responding"

I am staying in a hotel and my 3gs iphones keep getting "dns server not responding" my computers work fine in my room. My iphones don't but if I walk out in the hallway the iphones work fine. Help?

Found what was the problem on my configuration.
Since NLB VIP did not respond when traffic was going from other networks (Internet included) i had to reconfigure NLB from unicast to multicast. Then thing started to work but i had DNS resolution error.
Solution:
A BUG! When you change NLB cluster type, ipv6 that is configured on it gets removed so you have to enter it again. That's the same IPV6 IP under Infrastructure servers - DNS that ends with :3333::1 for your .domain.local

AT-MIO-16XE-50 device is not responding to the selected base address

I'm trying to install my AT-MIO-16XE-50 DAQ board onto my Windows NT desktop computer, but I'm having trouble.
Here's what I've done: I've installed LabView 5.1 and the NIDAQ 7.0 software onto my computer first. Then I've physically installed the DAQ board into my computer. After starting the computer, the plug-and-play system seems to recognize the new hardware and install drivers for it. It then says I need to reboot the computer, so I reboot the computer.
When I then look at my device manager, it lists AT-MIO-16XE-50 twice. Under the properties/resources tab, one of them lists "input/output range", "interrupt request", "direct memory access", and "direct memory access" (i.e., 2 "direct memory access"s). The second one only lists "direct memory access" once and nothing else under the properties/resources tab. Also, the first one says that it is working properly while the second one says that it is not working properly (Code 10). I've played around with chaging the "direct
memory access" numbers and after rebooting the computer have gotten both AT-MIO-16XE-50's in the device manager to say that they're working properly. So, now the DAQ board appears to be installed correctly, because the device manager reports no problems with it. However, there are still 2 of them. My first question is this: should there be only 1 entry in the device manager list, or are there supposed to be the 2 that I see? The entries do appear to be different from each other, but they're for the same device, so that's a little confusing.
When I open my Measurement and Automation explorer, only one AT-MIO-16XE-50 device is listed (so this looks good), and under "properties" all 3 "direct memory access" numbers are listed. So, this all seems good. But, when I click on "test resources" or "test panel", I get an error message saying that "the device is not responding to the selected base address". Considering that this device was plug-and-play, and I did not set the base address manually, I don't understand why I'm getting this error message.
What I've tried is to change the "input/output range" number by using the device manager. I've tried a few different settings (rebooting the computer after each change) and none of the different "input/output range" settings seem to work.
I'd appreciate it if you could give me any help on figuring out how to resolve this "not responding to base address" problem. The info on your web site
appears to suggest flipping dip-switches on the DAQ card, but my card does not have any dip switches because it is plug-and-play. So, right now I'm
clueless! Thanks for reading this, and I hope that you have more insight than I do.

Smaria,
The AT-MIO-16XE-50 shows up twice in the Device Manager because it reserves three DMA channels, and the ISA bus only allows two DMA channels per ISA slot. You mentioned that you were able to get both devices working properly in the Device Manager. Below is a link to a KnowledgeBase that describes the proper procedure to successfully accomplish this. You should verify that this is the procedure you followed:
Exclamation Mark Appears with Error Code 10 on Windows XP/2000/98 After Installing AT-MIO-16E-10
Spencer S.

Outlook 2013 Not Responding and Offline Address Book Issues with Office 365

Around 3 months ago I setup a small business with Office 365 for email. They have 10 PCs, all running newly installed Windows 7 Professional 64-bit, eight with Office 2013 and two with Office 2010. All are connected to a local domain (Server Essentials
2012) with a single internet connection through a new TP-LINK router. Each user logs into their own PC only.
The network runs perfectly, internet connection is good but there seems to be RANDOM, INTERMITTENT issues with email not being SENT from Outlook every so often. Email will sit in the outbox for up to an hour sometimes before, eventually, being sent. Incoming
email seems ok, although this is more difficult to tell. At others times, email will be sent instantly - the size of the message and any attachments makes no difference.
The issue has happened at some point on every one of the PCs but no particular PC/user seems worse than any other. When email is stuck on one user's PC it can still be sent ok by other users at the same time - so the internet connection is not down. Users can
can always login to the OWA service ok and iPhones etc. all sync ok even when email is stuck in the Outbox.
To debug the issue I have worked on one particular user's PC and carried out the following changes -
Changes that made no difference
I have checked the router. A SPI firewall is available on the router but this is switched off.
I have changed the MTU on the router with no effect.
There are no unsual add-ins to Outlook
Outgoing email virus scanning is disabled
Outlook is NOT integrated with Lync
The OST file is around 1.7 GBytes is size.
I have recreated the Outlook profile twice but this made no difference
Switched OFF "Cached Exchange Mode" - this made things worse !
The Outlook address book is set to \Offline Global Address List
I have disabled with Windows firewall on the client PC - no change
I have adjusted the KeepAliveTime for packets in the registry of the PC to 20 minutes
Changes that reduced the frequency of "Not Responding"
I have changed the Outlook automatic Send/Receive time from 30 to 10 minutes - this seemed to help
Possible Related Problem
I have attempted to download the offline address book manually - this hangs at "Copying offline address book template file" in the Send/Receive dialog and there a NO OAB files in the data file location on the PC.
So the only measure that has so far "helped" has been the Outlook Send/Receive time change - now set to 10 minutes. Even so, Outlook will occasionally go "Not Responding" for 30 minutes or more (no windows active - only option
is to close and reopen Outlook).
There does seem to be a problem with the Offline Address book. I can download this ok for this user on my home PC (Outlook 2010) but this will not download manually on the work pc with Outlook 2013 (despite following all the debug steps above).
On work PC I can see literally hundreds of "Schannel" errors in the Windows System event logs -
Error - Event 36888 Schannel
The following fatal error was generated :10
The internal error state is 10
These errors occur every 2-4 minutes continually all the time Outlook is running. When Outlook is closed the "Schannel" errors stop !
Can anyone suggest what else to try, please ?
I have already investigated this issue on the Office 365 Community Forum, and the Outlook forum and they suggested that it was a client (i.e Outlook) issue and that I should post here for further information.
Thanks for reading !

An update to this problem.
I brought one of the office PCs back to my home network and connected it up there. With no changes to the PC I was immediately able to download the Offline Address Book without errors.
This suggests to me that there must be some problem with the internet connection or router setup in the office environment.
The router is a TP-LINK W8970. The internet connection is PPPoA. I have seen some suggestion that an SPI firewall can cause issues. This router has an SPI firewall but this feature is disabled on the router.
While investigating this issue I have frequently been connected remotely to an office PC - sometimes for up to an hour or more. During these periods I have not experienced any connection dropouts so the actual internet connection seems to be ok (i.e. it is
not dropping out).
However, something seems to be preventing the Outlook client from connecting properly with the Office 365 Exchange server in the office environment - or something is dropping the connection to Outlook. Does anyone know of any router settings that might affect
this ?
I could try changing the office router but I do not have a spare available. Can anyone suggest a reasonably low cost, currenbtly available router that they know definitely works in the Office 365 environment so that I could buy this for test purposes ?

The device PCI 6036E: Analog Input error:"the device is not responding to the base address",Output :No signal

I am using PCI 6036E DAQ card, DAQ 6.9.2. , I have not connected to any external device.
When I tested card(in Test Panel of MAX2.2,DAQ 6.9.2) an error appearing �the device is not responding to the base address� � then I pressed Yes, Then TestPanel window appearing�
In analog Input Tag, there is an error �-10805�. This error also appearing when I run the standard analog input samples (use Delphi 6.0).
I tested analog output functions in TestPanel, Delphi Examples, LabView 6.1. There are not error appearing but there is not output signal (using Oscilloscope to see).
Output, Input digital functions are working correctly.
Next I try to foll
ow all the instruntions as recommended:
-Changing TO another slots PCI
-Reinstall Os WinXP,98SE�
-Use another Computer�
But all of the cases are still not working.(the above error still appeared, no output signal)

Nvd,
I'm sorry to hear about the problems that you are running into with your DAQCard. I can understand your frustration with the errors that you are seeing. You mention that you have tried to do some troubleshooting, I was wondering if you have tried all the troubleshooting techniques listed in this KnowledgeBase:
http://digital.ni.com/public.nsf/websearch/DCFCDB240788F8D486256D6A00834D80?OpenDocument
If you have tried all of those things, I would suggest one additional thing to try. I would suggest updating your NI-DAQ drivers to version 7.0. These drivers are the newest versions of our Data Acquisition Drivers, and can be downloaded from our website here:
http://digital.ni.com/softlib.nsf/webcategories/85256410006C055586256BBB002C128D?OpenDocument&
node=132060_US
If you have tried all of the above troubleshooting options, please post a detailed description of what you have tried. This may help to clarify what is going wrong.
Jed R.
Applications Engineer
National Instruments

IP Address or sender did not respond messages

I am on Tiger and my mother in law is on Leopard, both are Macbooks. She is the only person I cannot video chat with. The errors come up either Invalid IP address or that I (when calling her) did not respond. On her end it says that I cancelled the connection. I thought it was her router, etc, but today I was at my folks (Leopard Macbook) and rang her for a video chat and it worked fine?! I can video fine with others with Leopard and Tiger, it is only her that it doesn't seem to want to work...any would would be awesome!! Thanks

Tell us about how she connects to the Internet ?
If she is wireless and Ethernet she can get this Problem
AS can having a Modem that routes and a router both doing DHCP
As Can using Parallels to run Windows and sharing the Mac Ip
4:00 PM Saturday; March 1, 2008

" device does not respond to is base address, do you want to continue ?" OR " Le périphérique ne répond pas à l'adresse de base"

Environment :
NI-DAQ 6.9.3
PCI-6025 E Card
LabPC1200 Card
PCI serial interface card
AGP video Card
Measurement & Automation explorer 2.0
After using the PCI-6025 E during an hour with the Measurement & Automation explorer 2.0 software, the message :�Le périphérique ne repond pas à l�adresse de base, voulez vous continuer?� or « the device does not respond to is base address, do you want to continue ? »
All the informations , even in the System Configuration Panel, seem to be in order. It seems that the problem occurs after I have tried to use also the Lab PC 1200 by the way of the Measurement & Automation explorer 2.0.
I have tried to:
� restart the software,
� stop the PC and restart it after a while,
� uninstall NI-DAQ 6.9.3 and all NI softwares
� Install NI-DAQ 7
The same problem was always here.
� stop the PC remove all the Cards except the video card
� restart the PC
� stop the PC and put only the PCI-6025E Card
The same problem was always here.
� uninstall NI-DAQ 7 and all the NI softwares
� stop the PC and remove the PCI-6025E Card
� Install NI-DAQ 6.9.3
� Stop the PC and install the PCI-6025E Card in another PCI Slot.
The same problem was always here.
I have each time try to change the number of the card by the use of Measurement and automation explorer 2.0 but with no success.
How can I do to use again this card?
I really thank you for any response.
NICOLAS Gabriel.

Hey Nicolas,
Try opening up the Reset Device.vi inside of LabVIEW and execute the VI. All you have to do is set the correct device number and check that the error returned is 0 and not another error number. In many cases a crashed program can cause the devices to enter into an unsafe state that they need to be reset from.
It is possible that you damaged the device and that it will need to be sent in for repair, but in most cases a reset will fix the issue. Also, try opening up MAX and right-click on Traditional NI-DAQ Devices under Devices and Interfaces and click on reset Traditional NI-DAQ. If that doesn't work try the Device reset under DAQmx as well.
I hope this helps out.
Joshua P.
National Instruments

I am not able to telnet my content rule VIP address

I am not able to telnet my content rule VIP address and port number. But I am able to direct to telnet to service servers, which are added into the content rule set. Can anyone tell me why. I have update the latest WEBOS 5.00 Build 69. The content switch model is 11050. thank you very much .

Is possible one armed and in line in the same content switch ?
Currently I have some content rule are using one armed solution, there is only one rule I need to make the server see the original IP. I guess my question is , can I have this rule use in -line solution only, so I will not have to impact other rules set.
The other question since this content rule's service sever have only one interface only, Can I have this in-line solution go in the content switch and come out content switch in the same server farm switch ? Thank you for all the help.

TS2481 Address book "not responding" after troubleshooting SyncServices. Anyone else have this problem?

I had been having an issue with contacts repeatedly duplicating and sometimes disappearing in my address book. This appeared to be a problem with SyncServices, so I followed the steps to troubleshoot SyncServices, archived my contacts, de-duplicated them, cleared the caches and restarted.
I was able to load my contacts back into the address book, but after attempting to de-duplicate again, I started to get the rainbow wheel and the address book is "Not Responding." Force quitting and rebooting have had no effect.
Any advice?

My Address book was not opening anymore and went to "not responding". Forced stop did not resolve the issue.
Most likely to be an icloud issue. Try switching off contacts in your icloud settings in the configuration icon of your Mac. Delete contacts as otherwise you will end up with all duplicate contacts. If you have any contacts stored on your mac, be aware that when switching contacts in iCloud on again, all will be uploaded into iCLoud. So if you don't watn, export and delete before switching back on.
This solved it for me.

The device is not responding to the selected base address

my DAQ card is PC-LPM-16, a few days ago, i configed it properly. and i didn't use it for a few days, but didn't plug out from my computer. today i want to use it, but the MAX test showed that "The device is not responding to the selected base address." i setup my hardware and software again, but still can't resole it, what can i do now?
thank you very much.
liyongqin
2001-10-23

"The error could be happening for a variety of reasons. The first thing I would do is to visit www.ni.com/support/daq and follow the installation procedure, which includes troubleshooting steps on the error you are receiving.
If that doesn't work then try to install the board in another computer with no other devices installed. This will test to make sure the board is not bad. If all else fails call National Instruments and have someone troubleshoot the board and return and repair it if necessary."

Device is not responding to the selected base address-DAQCard-AI-16E-4

Configuration: WinXP, Labview express 7 evaluation, & DAQCard-AI-16E-4
Driver installed : TDAQ741
Without the PCMCIA card in my laptop, I have installed my Labview and then the driver TDAQ741. When I opened the Measurement & Automation Explorer and tried the Test Panel, I'm getting "The device is not responding to the selected base address."
Can anyone tell me how do I fix this problem?

Hi yoyoman-
Common solutions to the "...not responding to the selected base address..." error are suggested in this KB. Please take a look and let us know if you still run into problems after trying these.
Thanks-
Tom W
National Instruments

Cisco ACE VIP not responding to Pings

I've searched..... I cannot figure out why my VIPs do not ping. I have two vlans that both replay to a ping on the interface IPs. And I'm new at this, thanks in advace.
GKEL2-ACE1/35568059-Axia# show run
Generating configuration....
no ft auto-sync startup-config
logging enable
logging timestamp
logging trap 5
logging host 10.85.242.100 udp/514
login timeout 60
crypto chaingroup walnut-wcrt100
cert .dom.cer
cert wcrt100.pem
crypto chaingroup .dom-wcrt100
cert .dom.cer
cert wcrt100.pem
crypto csr-params .dom
country CA
state AB
organization-unit IT
common-name .dom
serial-number 1000
email support
crypto csr-params .dom
country CA
state AB
organization-unit IT
common-name .dom
serial-number 1001
email support
access-list ANYONE line 10 extended permit ip any any
access-list ANYONE line 20 extended permit icmp any any
access-list All line 1 extended permit ip any any
probe http HTTP1025
port 1025
interval 2
faildetect 2
passdetect interval 2
request method get url /Login.css
open 1
probe icmp PING
interval 2
faildetect 2
passdetect interval 60
probe tcp PROBE-TCP
interval 2
faildetect 2
passdetect interval 10
passdetect count 2
open 1
rserver redirect REDIRECT-HTTPS
webhost-redirection https://%h%p 302
inservice
rserver host WL1
ip address 10.205.70.100
inservice
rserver host WL2
ip address 10.205.70.101
inservice
rserver host WLDev1
ip address 10.205.71.202
inservice
rserver host WLDev2
ip address 10.205.71.203
inservice
rserver host WLTest1
ip address 10.205.71.150
inservice
rserver host WLTest2
ip address 10.205.71.151
inservice
serverfarm redirect REDIRECT-SERVERFARM
rserver REDIRECT-HTTPS
    inservice
serverfarm host WEBLOGIC-7433
predictor leastconns
probe PING
rserver WL1 7433
    inservice
rserver WL2 7433
    inservice
serverfarm host WEBLOGIC-PROD
predictor leastconns
probe PING
rserver WL1 1025
    inservice
rserver WL2 1026
    inservice
serverfarm host WEBLOGIC-TEST-SSH
predictor leastconns
rserver WLTest1 22
    inservice
rserver WLTest2 22
    inservice
sticky http-cookie acecookie STICKY-INSERT-COOKIE
cookie insert
serverfarm WEBLOGIC-PROD
action-list type modify http REWRITE
header insert response Via header-value "1.1 web:%ps (ace10-8/a2)value"
header insert request Via header-value "1.1 web:%ps (ace10-8/a2)value"
header insert request X-Forwarded-Proto header-value "%pd"
ssl url rewrite location "*.*"
ssl header-insert session Id
ssl-proxy service ssl-client
ssl-proxy service ssl-proxy
key netcracker.cal.dom.key
cert netcracker.cal.dom.cer
chaingroup netcracker.cal.dom-wcrt100
class-map match-any L4VIPCLASS
2 match virtual-address 10.205.70.80 any
class-map type http loadbalance match-any L7-URL
2 match http url /*.*
class-map type http loadbalance match-all L7SLBCLASS
2 match http url /*
class-map type management match-any REMOTE-MANAGEMENT
2 match protocol telnet any
3 match protocol icmp any
4 match protocol ssh any
5 match protocol snmp any
6 match protocol http any
7 match protocol https any
class-map match-any SSH_Test
2 match virtual-address 10.205.71.80 tcp eq 22
class-map match-any weblogic-7433
2 match virtual-address 10.205.70.80 tcp eq 7433
class-map match-any weblogic-http
2 match virtual-address 10.205.70.80 tcp eq www
class-map match-any weblogic-https
2 match virtual-address 10.205.70.80 tcp eq https
policy-map type management first-match REMOTE-MANAGEMENT
class REMOTE-MANAGEMENT
    permit
policy-map type loadbalance first-match L7SLBPOLICY
class L7SLBCLASS
    ssl-proxy client ssl-client
policy-map type loadbalance first-match SSH_Test_Policy
class class-default
    serverfarm WEBLOGIC-TEST-SSH
policy-map type loadbalance first-match weblogic-7433-policy
class class-default
    serverfarm WEBLOGIC-7433
    ssl-proxy client ssl-client
policy-map type loadbalance first-match weblogic-http-policy
class class-default
    serverfarm REDIRECT-SERVERFARM
policy-map type loadbalance first-match weblogic-https-policy
class L7-URL
    sticky-serverfarm STICKY-INSERT-COOKIE
class class-default
    serverfarm WEBLOGIC-PROD
    action REWRITE
    ssl-proxy client ssl-proxy
policy-map multi-match L4LSBPOLICY
class L4VIPCLASS
    loadbalance policy L7SLBPOLICY
policy-map multi-match LB-VIP
class weblogic-http
    loadbalance vip inservice
    loadbalance policy weblogic-http-policy
    loadbalance vip icmp-reply
    nat dynamic 1 vlan 3440
class weblogic-https
    loadbalance vip inservice
    loadbalance policy weblogic-https-policy
    loadbalance vip icmp-reply
    nat dynamic 1 vlan 3440
    ssl-proxy server ssl-proxy
class weblogic-7433
    loadbalance vip inservice
    loadbalance policy weblogic-7433-policy
    loadbalance vip icmp-reply
    nat dynamic 1 vlan 3440
    ssl-proxy server ssl-proxy
policy-map multi-match LB-VIP-Test
class SSH_Test
    loadbalance vip inservice
    loadbalance policy SSH_Test_Policy
    loadbalance vip icmp-reply
interface vlan 3440
description Internal Production
ip address 10.205.70.250 255.255.255.0
access-group input All
access-group output All
nat-pool 1 10.205.70.249 10.205.70.249 netmask 255.255.255.0 pat
service-policy input REMOTE-MANAGEMENT
service-policy input LB-VIP
service-policy input L4LSBPOLICY
no shutdown
interface vlan 3516
description Internal Test/Dev
ip address 10.205.71.250 255.255.255.0
access-group input All
access-group output All
nat-pool 2 10.205.71.249 10.205.71.249 netmask 255.255.255.0 pat
service-policy input REMOTE-MANAGEMENT
service-policy input LB-VIP-Test
no shutdown
interface vlan 3520
description LB
ip address 10.205.72.1 255.255.255.0
access-group input All
access-group output All
no shutdown
ip route 0.0.0.0 0.0.0.0 10.205.70.253
username admin password 5 $1$r2r0NmEH$z8S0RxYdhwOE4RGXQ41 role Admin domain default-domain
username cust_admin password 5 $1$/tOIIfUK$yigE519cqLq1IFgX. role Admin domain default-domain

I have removed that service policy completely. It was from some knowledgebase article when I was trying to get http redirection working.
There is no more L4LSBPOLICY nor L4VIPCLASS, Thanks a lot for looking at this...
GKEL2-ACE1/35568059-Axia# show service-policy summary
service-policy: LB-VIP
Class                            VIP             Prot Port        VLAN          State    Curr Conns   Hit Count Conns Drop
weblogic-http                    10.205.70.80    tcp   eq 80       1,3440        IN-SRVC           0       50773         53
weblogic-https                   10.205.70.80    tcp   eq 443      1,3440        IN-SRVC           0        7406        112
weblogic-7433                    10.205.70.80    tcp   eq 7433     1,3440        IN-SRVC           0      145321         30
service-policy: LB-VIP-Dev
Class                            VIP             Prot Port        VLAN          State    Curr Conns   Hit Count Conns Drop
weblogic-http-dev                10.205.71.90    tcp   eq 80       1,3516        IN-SRVC           0           0          0
weblogic-https-dev               10.205.71.90    tcp   eq 443      1,3516        IN-SRVC           0           0          0
weblogic-7433-dev                10.205.71.90    tcp   eq 7433     1,3516        IN-SRVC           0           0          0
service-policy: LB-VIP-Test
Class                            VIP             Prot Port        VLAN          State    Curr Conns   Hit Count Conns Drop
SSH_Test                         10.205.71.80    tcp   eq 22       1,3516        IN-SRVC           0          29         24
weblogic-http-test               10.205.71.80    tcp   eq 80       1,3516        IN-SRVC           0         117         40
weblogic-https-test              10.205.71.80    tcp   eq 443      1,3516        IN-SRVC           0         161         61
weblogic-7433-test               10.205.71.80    tcp   eq 7433     1,3516        IN-SRVC           0          27         11
class-map type http loadbalance match-any L7-URL
2 match http url /*.*
class-map type http loadbalance match-all L7SLBCLASS
2 match http url /*
class-map type management match-any REMOTE-MANAGEMENT
2 match protocol telnet any
3 match protocol icmp any
4 match protocol ssh any
5 match protocol snmp any
6 match protocol http any
7 match protocol https any
class-map match-any SSH_Test
2 match virtual-address 10.205.71.80 tcp eq 22
class-map match-any weblogic-7433
2 match virtual-address 10.205.70.80 tcp eq 7433
class-map match-any weblogic-7433-dev
2 match virtual-address 10.205.71.90 tcp eq 7433
class-map match-any weblogic-7433-test
2 match virtual-address 10.205.71.80 tcp eq 7433
class-map match-any weblogic-http
2 match virtual-address 10.205.70.80 tcp eq www
class-map match-any weblogic-http-dev
2 match virtual-address 10.205.71.90 tcp eq www
class-map match-any weblogic-http-test
2 match virtual-address 10.205.71.80 tcp eq www
class-map match-any weblogic-https
2 match virtual-address 10.205.70.80 tcp eq https
class-map match-any weblogic-https-dev
2 match virtual-address 10.205.71.90 tcp eq https
class-map match-any weblogic-https-test
2 match virtual-address 10.205.71.80 tcp eq https
policy-map type management first-match REMOTE-MANAGEMENT
class REMOTE-MANAGEMENT
    permit
policy-map type loadbalance first-match L7SLBPOLICY
class L7SLBCLASS
    ssl-proxy client ssl-client
policy-map type loadbalance first-match SSH_Test_Policy
class class-default
    serverfarm WEBLOGIC-TEST-SSH
policy-map type loadbalance first-match weblogic-7433-dev-policy
class class-default
    serverfarm WEBLOGIC-7433-Dev
policy-map type loadbalance first-match weblogic-7433-policy
class class-default
    serverfarm WEBLOGIC-7433
    ssl-proxy client ssl-client
policy-map type loadbalance first-match weblogic-7433-test-policy
class class-default
    serverfarm WEBLOGIC-7433-Test
    ssl-proxy client ssl-client
policy-map type loadbalance first-match weblogic-http-dev-policy
class class-default
    serverfarm REDIRECT-SERVERFARM
policy-map type loadbalance first-match weblogic-http-policy
class class-default
    serverfarm REDIRECT-SERVERFARM
policy-map type loadbalance first-match weblogic-http-test-policy
class class-default
    serverfarm REDIRECT-SERVERFARM
policy-map type loadbalance first-match weblogic-https-dev-policy
class L7-URL
    sticky-serverfarm STICKY-INSERT-COOKIE-DEV
class class-default
    serverfarm WEBLOGIC-DEV
    action REWRITE
policy-map type loadbalance first-match weblogic-https-policy
class L7-URL
    sticky-serverfarm STICKY-INSERT-COOKIE
class class-default
    serverfarm WEBLOGIC-PROD
    action REWRITE
    ssl-proxy client ssl-proxy
policy-map type loadbalance first-match weblogic-https-test-policy
class L7-URL
    sticky-serverfarm STICKY-INSERT-COOKIE-TEST
class class-default
    serverfarm WEBLOGIC-TEST
    action REWRITE
    ssl-proxy client ssl-proxy-nctest
policy-map multi-match LB-VIP
class weblogic-http
    loadbalance vip inservice
    loadbalance policy weblogic-http-policy
    loadbalance vip icmp-reply active
    nat dynamic 1 vlan 3440
class weblogic-https
    loadbalance vip inservice
    loadbalance policy weblogic-https-policy
    loadbalance vip icmp-reply
    nat dynamic 1 vlan 3440
    ssl-proxy server ssl-proxy
class weblogic-7433
    loadbalance vip inservice
    loadbalance policy weblogic-7433-policy
    loadbalance vip icmp-reply
    nat dynamic 1 vlan 3440
    ssl-proxy server ssl-proxy
policy-map multi-match LB-VIP-Dev
class weblogic-http-dev
    loadbalance vip inservice
    loadbalance policy weblogic-http-dev-policy
    loadbalance vip icmp-reply
    nat dynamic 1 vlan 3516
class weblogic-https-dev
    loadbalance vip inservice
    loadbalance policy weblogic-https-dev-policy
    loadbalance vip icmp-reply
    nat dynamic 1 vlan 3516
class weblogic-7433-dev
    loadbalance vip inservice
    loadbalance policy weblogic-7433-dev-policy
    loadbalance vip icmp-reply
    nat dynamic 1 vlan 3516
policy-map multi-match LB-VIP-Test
class SSH_Test
    loadbalance vip inservice
    loadbalance policy SSH_Test_Policy
    loadbalance vip icmp-reply
    nat dynamic 1 vlan 3516
class weblogic-http-test
    loadbalance vip inservice
    loadbalance policy weblogic-http-test-policy
    loadbalance vip icmp-reply
    nat dynamic 1 vlan 3516
class weblogic-https-test
    loadbalance vip inservice
    loadbalance policy weblogic-https-test-policy
    loadbalance vip icmp-reply
    nat dynamic 1 vlan 3516
    ssl-proxy server ssl-proxy-nctest
class weblogic-7433-test
    loadbalance vip inservice
    loadbalance policy weblogic-7433-test-policy
    loadbalance vip icmp-reply
    nat dynamic 1 vlan 3516
    ssl-proxy server ssl-proxy-nctest
interface vlan 3440
description Internal Production
ip address 10.205.70.250 255.255.255.0
mac-sticky enable
access-group input All
access-group output All
nat-pool 1 10.205.70.249 10.205.70.249 netmask 255.255.255.0 pat
service-policy input REMOTE-MANAGEMENT
service-policy input LB-VIP
no shutdown
interface vlan 3516
description Internal Test/Dev
ip address 10.205.71.250 255.255.255.0
mac-sticky enable
access-group input All
access-group output All
nat-pool 1 10.205.71.240 10.205.71.249 netmask 255.255.255.0 pat
service-policy input REMOTE-MANAGEMENT
service-policy input LB-VIP-Test
service-policy input LB-VIP-Dev
no shutdown
interface vlan 3520
description LB
ip address 10.205.72.1 255.255.255.0
access-group input All
access-group output All
no shutdown
ip route 0.0.0.0 0.0.0.0 10.205.70.253

Search on the address book do not responds

Hi! I´m a begginer and I have an issue with my address book. After add a couple of birthdays (which are synchronized with iCal), search on the address book do not responds.
Anyone Knows anything about that?
Thanks!

I found the solution. The answer is just unmark "sync contacts with icloud" on system pref, select "delete contacts from your mac". And then turn on "sync contacts with icloud". Thas All.
PD: don´t forget to check all your contacts back up on icloud.com

Vip address not responding

Similar Messages

Maybe you are looking for