I frame only 4:2:2 encoding settings?

Hi
Can someone please tell me the AME setting to create an MPEG-2 Program Stream with the following specs?
625/50 PAL
Video Size: 720 x 576
50 Mbps CBR I frame only
Profile: 422P@ML
Colour Sampling: 4:2:2
Many thanks
Riz
PS. FYI, these are the SD (PAL) video specs for AdStream UK digital delivery service.

Thank you for the MediaInfo tip.
I have downloaded and run the file I created. Details are below but I am not sure where I should read 'I-Frame Only'? The entire broadcast industry uses that term but for some reason neither Adobe nor MediaInfo mentions anything about it? Also, how can I produce 4:2:2 instead of 4:2:0 as I produced?
Video
ID                                       : 224 (0xE0)
Format                                   : MPEG Video
Format version                           : Version 2
Format profile                           : Main@High
Format settings, BVOP                    : No
Format settings, Matrix                  : Default
Format settings, GOP                     : N=1
Duration                                 : 1mn 20s
Bit rate                                 : 50.0 Mbps
Width                                    : 720 pixels
Height                                   : 576 pixels
Display aspect ratio                     : 16:9
Frame rate                               : 25.000 fps
Standard                                 : PAL
Color space                              : YUV
Chroma subsampling                       : 4:2:0
Bit depth                                : 8 bits
Scan type                                : Interlaced
Scan order                               : Top Field First
Compression mode                         : Lossy
Bits/(Pixel*Frame)                       : 4.823
Time code of first frame                 : 00:00:00:00
Time code source                         : Group of pictures header
Stream size                              : 478 MiB (97%)
Color primaries                          : BT.709
Transfer characteristics                 : BT.709
Matrix coefficients                      : BT.709
All help is appeciated.

Similar Messages

  • Bad key frame artifacts with preset mobile encode settings.

    AME CS6 encodes very poor quality low bitrate encodes (when we choose any of the mobile h.264 presets). There is noticeable key frame artifacts about once every second.
    In contrast, the free Handbrake program has been able to encode great video since its early versions a few years back.
    I didn't expect such poor quality from a product which cost so much.
    Will Adobe tweak the presets properly to produce DECENT low bit rate videos please?

    That request is best made directly to Adobe, rather than in a user forum.
    https://www.adobe.com/cfusion/mmform/index.cfm?name=wishform

  • How to encode 50 MB constant bit rate I Frame only MPEG-2 Program Stream

    I want to do a test upload to a digital programme delivery service. I'll be encoding a short clip for FTP upload.
    The specs the company sent says material should be encoded as follows:
    "50 MB constant bit rate I Frame only MPEG-2 Program Stream direct from digital source."
    Can anyone translate this into Compressor settings?
    Material also must have timecode.
    Thanks

    50MB constant bitrate? I hope you meant 50 Mbps... hehe. Hmmm... 29 Mbps seems to be max, using Compressor.
    To get a constant bit rate (CBR), choose One Pass CBR under the Quality tab in the Inspector.
    I am not sure if Compressor can do I-Frame only, but it can give you an IP GOP structure. Setting the GOP Structure to IP, and the GOP Size to the lowest possible gives you the best possible quality, but also the largest file size.
    For audio, choose AIFF, and make sure it gets the same name as the .m2v, but of course with the right .aif suffix.
    To make an MPEG-2 Program Stream, you need to use MPEG Streamclip (freeware).
    Open the .m2v file in MPEG Streamclip (the audio should automaticly load with the video file if they have the same file name). Choose the file menu and choose Covnvert To MPEG Using MP2 Audio.

  • Project will not render with 'I-Frame only MPEG'

    Hey Adobe, I am posting this at your request.    
    I previously used to have an old Intel Core2 chip system.
    I upgraded this so that my video editing life would be faster.  I have a new motherboard, with a new intel I7-4770 @ 3.5Ghz chip. same memory (16Gb-1600), graphics card, hard disk, DVD drive, etc..
    On the Core2 system, video projects which I worked on all worked fine. I mainly use a Sony Z5 to shoot video which creates .M2T files.
    On my old system, running Premiere CC it ALL WORKED - no problems, but on the new build, it crashes EVERYTIME i try to render, with 'Error Compiling Movie - Unknown Error'
    Having spent FOUR hours on the phone to your tech supports in India, they came up with a workaround. I stress - it's a workaround, not a solution.
    They found that if i changed the sequence to be 'Custom' and then selected 'Microsoft AVI' (and any Codec, doesn't matter which) as the Preview File Format  instead of 'i-Frame Only MPEG' then yes - it renders.
    The tech told me that this was because 'M2T' files were fussy, and needed to be treated like this.
    WRONG!
    if this *needed* to be the case, then why did it work previously on my old system without any problem?
    Also, if I take a project that crashes on my desktop PC, and copy it over onto my laptop, de-activate Premiere on my desktop and activate on my laptop and run in on there .. IT RENDERS FINE, using the 'I-Frame Only MPEG' setting.
    Also, i shot some video with a Nikon D5100 which produces full HD .MOV clips, *AND THE SAME PROBLEM STILL OCCURS* when rendering on my desktop PC, and only renders when i switch the Preview File Format to be 'Microsoft AVI - so it's not related to the .M2T video file type.    
    So I can render stuff, but ultimately it's a workaround and not a solution, as when I am finished with a project, and want to archive it off I do so by exporting and choosing 'Match Sequence Settings', with with Microsoft AVI selected, it wants to therefore obviously export it as an AVI, which i do not want - I want to export it as 25mbps MPEG which is the original quality/format that it was shot at.  When i try and do this with 'i-Frame Only MPEG' selected as the sequence type - you've guessed it, Media Encoder crashes
    So.  Why does i-Frame Only MPEG work on one machine (my laptop), but on my main machine (desktop) which i want to use, it doesn't? What piece of software/codec/file am I missing?
    - i have installed from clean build of Windows
    - i have deactivated and reactived Premiere CC
    - i have uninstalled Premiere CC and reinstalled it
    - i have uninstalled all Cloud CC programs and reinstalled them
    - I have run CC cleaner too
    - I have the latest video drivers for my graphics card (it is the same graphics card that worked just fine on my old system anyway, so is not the issue)
    - I have full Windows/Admin permissions. it is not a permissions problem
    please don't suggest any of those options.  None of them work.  I need someone who understands your software and knows what i-Frame only MPEG is to be able to tell me why it isn't working on my system.  I am now past the point of anger (because i have lost several days worth of worktime - and thus money) and being upset (because it's massively frustrating when somthing that previously worked now doesn't), and am now just at the point of being bewildered that no one there can seem to tell me what is going on here, and how to solve it.
    Many thanks,
    Geoff.

    I have to put in my 2 cents...and first of all I'm sorry things are happening that are not FANTASTIC results... etc... but there may be ways to make things better... but this stuff is complicated and extremely computer intensive ( math stuff with cpu and ram and stuff ) .. so the platform is very critical to best results.. not just the software.
    There's books on compression and how that stuff works ( lossless or not ) and it's all about changes from frame to frame and how to best make file size smaller while keeping every single pixel perfect in each frame... and this is unfortunately not standardized on planet earth. Different companies make up what they can to sell cameras and recording medium and so on..  there are some standards ( for broadcast and movies etc ) cause at some point some groups have to deal with delivery to PEOPLE to watch stuff.. and have decent quality to watch...
    In general this is very complicated and full of problems cause there is no single work flow , and probably never will be .
    What Jeff is talking about ( I think ) is that during the process of a computer program interpreting images ( frame by frame ) those pixels that have not changed a lot are described in a line of code by the software that says, " This stuff has not changed much if at all ".  Some stuff from one frame to the next one DID change a lot ( someone walking or someone running.. the running changes more fast ) .. and so lines of code say ,  " this stuff changed a LOT "....
    During the process of the software to determine what changed and how MUCH changed.. is complicated.. cause the program basically looks at frame A and then Frame F and notes the changes of pixels... and THEN ( as if that wasn't complicated enough ) the program then goes BACK  to frame A and then ahead to frame J ... so now it has expanded it's look at what changes have occurred...
    Now the ' CODEC " ( the specific codec used by the program you are running , like CC or avid or FCP ) is going to make it's best GUESS as to what really changed that matters the MOST to the image...so you basically get a nice image from A to J ..... but it is now compressed and taking up less room on your hard drive and ram etc....cause it is interpreting the image changes... and so on...
    So if you had every single frame without any guess work and no compression to save space cause those pixels did not change between A and J .... you would have HUGE FILES .... and no benefit in terms of being able to edit anything on a little home desktop computer... even if you have a really powerful one.. it is not going to be good enough to do that stuff....
    It would be unfair to say that adobe isn't doing the best they can to accomodate all the camera manufacturers " codecs " and give the best results they can , with a million different computer platforms and hardware out there you can buy off the shelf ....
    The I frames and B frames and other frames have to do with the " guessing game " of changes in pixels, changes with every " action " in those ranges of frames, and is very complicated... but there are books about it and what standards exist can be researched and studied if you're into that stuff....
    I am an idiot about this stuff but the main thing is dont give up.. and just try to be patient when things dont work out like you thought they would, and figure out what is going on so you can make things work the way you want...
    and good luck !

  • H264 encoding settings - problems with FLV/F4V conversions and playback... HELP!!!

    I do a lot of LIVE ENCODING and have been struggling with FMLE. I own the Adobe Creative Suite of applications and am pretty familiar with working with compatible/required formats, etc.
    We have been primarily using VP6/mp3 for encoding. Most of our work is SD. We also always seem to have trouble when trying to encode the FLV file to another format, audio always seem to be out of sync, but sometimes it works...
    Do you know why that would be regarding the FLV audio falling off sync when encoding to another format, such as MOV? Also, when we try to play back the FLV, the audio sounds garbled up and only plays well in Adobe Media Player.
    I keep hearing H264 encoding will provide better video, but I just can't get that to work. Also, why is it that my entire CS4 suite of applications can't read or playback the F4V file- that's unacceptable from Adobe, just a big huge pain the butt... I've had to buy several cheapie applications to try and read F4V files and try to convert it, except that converting F4Vs seems to be a hit-or-miss.
    What should I be using to playback and convert F4Vs? I also heard changing the extension to MP4 works, but I haven't seen that work, not even once. The cheap video conversion apps I have that read F4Vs are: FFMPEGX and Wondershare (Youtube). Sometimes they open F4V, but not most of the time... 
    I am using a super fast new Macbook Pro i7, 8GB ram (not the thunderbolt/usb3), CPU always runs smoothly and effectively.
    Also, I always use the Canopus ADVC-110 as my transcoder. I do both video via Firewire IN or Composite IN, then Firewire OUT into the Mac encoder. FMLE sees it ok, but I wonder if this device might be my problem.
    VP6 settings are as follows:
    VP6 video / MP3 audio
    300 to 500k video
    30 fps
    640x480 in/out
    44100hz audio
    56k audio
    We want to start using H264 encoding settings, but in my experience trying it out, the output file is ALWAYS PROBLEMATIC. Also, when testing a live stream, the audio seems to fall off sync with the video.
    I am looking for your recommendations on the H264 settings I should try. Most of my events are simple meetings with 1 to 5 speakers, mostly talking heads. We rarely encode high motion video, but I would also like to be able to adjust H264 settings for both talking heads and medium to high motion without (any) frame drops.
    I have tried streaming to multiple/different Flash Media Servers, archived only to file, and H264 results seem always bad.
    Any recommendations from professionals in the live streaming arena are much appreciated. I thank you for your time in advance.
    Thank you!
    Hugo

    Hello Hugo
    Sorry to know that you are facing these kind of issues, let me try to reply and understand issues one by one.
    >>We have been primarily using VP6/mp3 for encoding. Most of our work is  SD. We also always seem to have trouble when trying to encode the FLV  file to another format, audio always seem to be out of sync, but  sometimes it works...
    -- Which application you are using to convert FLV to other format?
    -- Is these any Audio - Video sync issue when you play FLV file in Adobe Media Player? if NO, it means FLV file created properly.
    >> Do you know why that would be regarding the FLV audio falling off sync  when encoding to another format, such as MOV? Also, when we try to play  back the FLV, the audio sounds garbled up and only plays well in Adobe  Media Player.
    -- Which application you are using to convert FLV to MOV? if FLV playabck fine and without a/v sync issue, it should convert MOV with a/v sync.
    -- It depend on audio codec selection by Media player or correct audio codec not installed for media player. Install appropriate audio codec to play in other media player if you dont want to play in Adobe Media Player.
    >> I keep hearing H264 encoding will provide better video, but I just can't  get that to work. Also, why is it that my entire CS4 suite of  applications can't read or playback the F4V file- that's unacceptable  from Adobe, just a big huge pain the butt... I've had to buy several  cheapie applications to try and read F4V files and try to convert it,  except that converting F4Vs seems to be a hit-or-miss.
    >> What should I be using to playback and convert F4Vs? I also heard  changing the extension to MP4 works, but I haven't seen that work, not  even once. The cheap video conversion apps I have that read F4Vs are:  FFMPEGX and Wondershare (Youtube). Sometimes they open F4V, but not most  of the time...
    -- Adobe Flash Media Server version 3.5 and later and Adobe Flash Media  Live Encoder 3 can record content in MPEG-4 (F4V) format using an  industry-standard recording technology known as "fragments" or "moof  atoms." Some MPEG-4 compatible tools and players do not support moof  atoms.
    The F4V Post Processor tool aggregates the information from all  the moof atoms into a single moov atom and outputs a new file." You can download the tool from above location: http://www.adobe.com/products/flashmediaserver/tool_downloads/
    Thanks

  • I frame ONLY MPEG2 video?

    Adobe Media Encoder documention states that:
    M Frames
    Number of B frames (bi‑directional frames) between consecutive I frames (intra‑frames) and P frames (predicted frames).
    N Frames
    Number of frames between I frames (intra‑frames). This value must be a multiple of the M frames value.
    This is great... but Media Encoder only allows the settings to go to 1, not 0...
    With a M and N Frame setting of 1, and reading the documentation, I am expecting to have 1 B Frame between every I Frame.
    Am I wrong? It reads as if a 1 frame M setting would allow 1 B frame...
    and the 1 frame N setting would also allow for one frame between each I frame, which would be the B frame...
    I need ALL I frames in my video!!
    And where does the Closed GOP settings come into all this?
    Maybe someone could give me the M N and GOP settings needed to create an all I Frame MPEG2 video?
    I'd love an explanation on how to translate the settings since I can't specify "0 Frames" between I frames, only 1...
    Thanks!!

    It's a Digital Spectrum MF-1040 plus
    http://www.dsicentral.com/products/mf-1040/Default.html
    The specs list mpeg 1,2 & 4. but when I called the company, the technician told me to use mpeg2 or .avi
    My daughter can take a card out of a point and shoot still camera with video capability and it plays without a problem including sound.

  • 50 MB constant bit rate I Frame only MPEG-2 Program

    '50 MB constant bit rate I Frame only MPEG-2 Program'
    What does that all mean, and how do I go about to find all these settings?
    It's for a commercial.
    Niel

    You're going to have a much easier time doing this in Compressor 3 than in 2, but what I'm assuming you're talking about here is a Program stream (multiplexed file) very similar to a transport stream.
    These MPEG-2 encoded files are used for broadcast and have both the audio and video contained in one file as opposed to DVD which requires those assets separated into elementary streams.
    If you're using Compressor 2, create a custom MPEG-2 setting and in the extras tab of the Encoder Pane select the Multiplexed option. Note though, that you will only be able to take the bit rate up to 20Mbps and it will only create a transport stream.
    In Compressor 3 you can choose between Program and Transport streams and you can increase the bit rate up to 40Mbps.
    BG

  • Turning off frame blending in Adobe Media Encoder

    Is there a way to turn off frame blending in Adobe Media Encoder?  I have a bunch of
    Flip Mino HD footage (1280x720p) which I wish to convert to P2 720p format so that
    I can more easily mix and match it in the Premiere timeline with actual P2 footage
    shot on an HVX200.
    I successfully used Media Encoder to perform this task but there is one problem.  The
    Flip footage is 30fps and P2 720p is 29.97fps.  So Media Encoder uses frame blending.
    The frame blending sometimes creates obnoxious artifacts so I would like to turn it
    off but there seems to be no way to do this (or alternatively "conform" the 30fps input
    to 29.97fps so that no blending is nescessary).
    After Effects CS4 would seem like an alternative since it has nice batch composition
    creation and rendering features but it cannot render to the P2 format - it appears to
    have a older version of Media Encoder embedded within it - predating P2 support.
    I would like a solution that is easily "batchable" as I have several hunderd Flip Mino HD
    clips that need to be processed.
    You might also ask, why not just import the Flip clips unchanged into Premiere CS4
    and mix them with the P2 clips?....I have tried this and it seems to drive Premiere crazy
    introducing various crashes and other strange behaviors.  The pre conversion to P2
    route seems to work fine.  I just want to get rid of the frame blending.

    I happened upon this video just before I made my posting and it doesn't help with the
    crashes/hangs.  When I import more than about 20 Flip Mino HD clips it seems to trigger
    some sort of memory corruption bug in Premiere.  Some of the clips start to just
    show as solid green in their thumbnail views in the timeline and scrubbing the timeline
    eventually hangs Premiere altogether.  This is reproducible on two different computers
    although the exact symptoms change slightly each time it is tried.  Importing only 3 or 4
    clips actually seems to work, at least for a short while.
    The problems happen even if the only thing imported into the project are Mino footage and
    the Sequence is set to Desktop or XDCAM mode.  So the crashes have nothing to do
    with P2 editing mode.
    The same installation of Premiere CS4 on one of these computers has been just used to
    successfully edit and render out a P2 project with hundreds of clips, stills and titles so the
    basic CS4 installation seems to be solid.
    I'll eventually file a bug report but for now I'm more interested in getting the job done.

  • Encoder Settings MIsmatch

    Hi all,
    Well...I just finished my first project in Leopard using my iLife 05. I can't seem to get my theme's to work correctly. However, I tried to go around that by creating a background image in LiveType to use to have something other than a black screen at my intro to the movie. So, I the project went through the entire encoding process and I came back with this error.
    +"The encoder settings of your project don't match iDVD's default value in Preferences. Do you want to change the setting and keep your encoded assets in the project?"
    If you click OK this will change the iDVD application encoder setting to match your project's and keep your encoded assets. If you select Update Project this will delete any already encoded material in your project and change the project setting to match iDVD's current setting.+
    I am not sure which way to go here. Any thoughts?

    Maina,
    If you ARE using Leopard (which isn't reflected in your profile), iDVD 5 isn't supported - sorry. That's why things aren't working correctly.
    Only iDVD 6.0.4 and iDVD 7.0.1 are Leopard compatible. See http://www.macintouch.com/leopard/compat.html

  • I-Frame Only MPEG in premiere pro cc

    please help........ I dont have I-Frame Only MPEG preview file format in sequence settings. It is set to Microsoft AVI. I want to set it to I-Frame Only MPEG.

    Start here;
    Get Started with Premiere Pro
    New to Premiere Pro? Get started with your first project — editing a video. In less than an hour, you'll learn to edit together different types of media to tell a video story.  

  • Dropped frames only on xserve raid

    dropped frames only on xserve raid
    i'm not able to capture on xserve raid without dropped frames. tihis was a working sytem bud one morning it dosn't work. i capture on mac pro internal drives or external fw drives without problems.
    the xserve raid is new formated in raid level5 [mac os extended journaled and striped in raid 0 extended] and the risult of kona system test are 178mb/sec write and 167mb/sec read.
    must bee enought for 8bit uncompressed pal, no? also if i divide the stripe set the system dosn't work on both controler. i tried also to change the fibrechannel cables!
    i checked also the fibrechannel card with expansion slot utility and the message is that runns at maximum speed.
    there are no error message on raid admin, the xserve raid appears ok.
    i'm shure that the fcp settings are ok, i know the list that regard dropped frames from apple.
    i'm desperate, can you help?
    thanks jochen
    system:
    mac pro 2x3ghz-5gb ram(from apple and the hardware test on the system dvd is ok)
    osx 10.4.10
    fibre channel card: lsilogic firmware 1.2.18.0 in slot 4
    xserve raid 15x250gb firmware 1.5.1/ 151c
    aja io (driver 3.0)
    raid admin 1.5.1 (diver 1.0)
    fcp 5.1.4

    I'm guessing conditioning is the same as optimization, but I can't find anything about it in the help documentation. I ran another capture test today with no problems.
    An interesting side event is that when I started experiencing dropped frames I ran the Kona System Test utility to verify write and read speeds. It wouldn't run (no write or read) on my RAID. I tried it on my Firewire drives with no problems. I discovered that in the Kona System Test preferences there is a choice of I/O API for Macintosh or Unix. When switching to the Unix I/O API the test ran fine with expected read and write speeds reported. I've used the Kona utility in the past without having to change that setting. I sent an inquiry to AJA.

  • Encoding settings on Imovie...Help please!

    I wonder if someone can help.  I have made a video for the school that is 4.2 GB heavy, dvd is 4.7 GB and iMovie says it's too big to burn.  It tells me to change encoding settings but I don't want to loose quality.  Has anyone got any suggestions please?  Will changing to High quality or professional quality affect the quality of the DVD?  Thank you very much for your help.  Regards, Aida

    iDVD encoding settings:
    http://support.apple.com/kb/HT1502?viewlocale=en_US
    Short version:
    Best Performance is for videos of up to 60 minutes
    Best Quality is for videos of up to 120 minutes
    Professional Quality is also for up to 120 minutes but even higher quality (and takes much longer)
    That was for single-layer DVDs. Double these numbers for dual-layer DVDs.
    Professional Quality: The Professional Quality option uses advanced two-pass technology to encode your video (The first pass determines which parts of the movie can be given greater compresson without quality loss and which parts can’t.  The second pass then encodes those different parts accordingly) , resulting in the best quality of video possible on your burned DVD. You can select this option regardless of your project’s duration (up to 2 hours of video for a single-layer disc and 4 hours for a double-layer disc). Because Professional Quality encoding is time-consuming (requiring about twice as much time to encode a project as the High Quality option, for example) choose it only if you are not concerned about the time taken.
    In both cases the maximum length includes titles, transitions and effects etc. Allow about 15 minutes for these.
    You can use the amount of video in your project as a rough determination of which method to choose. If your project has an hour or less of video (for a single-layer disc), choose Best Performance. If it has between 1 and 2 hours of video (for a single-layer disc), choose High Quality. If you want the best possible encoding quality for projects that are up to 2 hours (for a single-layer disc), choose Professional Quality. This option takes about twice as long as the High Quality option, so select it only if time is not an issue for you.
    Use the Capacity meter in the Project Info window (choose Project > Project Info) to determine how many minutes of video your project contains.
    NOTE: With the Best Performance setting, you can turn background encoding off by choosing Advanced > “Encode in Background.” The checkmark is removed to show it’s no longer selected. Turning off background encoding can help performance if your system seems sluggish.
    And whilst checking these settings in iDVD Preferences, make sure that the settings for NTSC/PAL and DV/DV Widescreen are also what you want.
    http://support.apple.com/kb/HT1502?viewlocale=en_US

  • Encoding settings for fast preview

    Is there any suggestions for the encoding settings in adobe media encoder to produce fast preview of Premiere CS4 project? I have done about 40 minutes long project with lots of effects and I just wanted to view the result on big screen, the quality can be very poor - all I wanted to do is to check the whole movie before exporting it to high quality Blu-ray.

    Launching uncompressed transcoding will produce huge file. I wonder, if there are some kind of draft transcoding settings/codecs which can be used to just preview final material. I already know, that when transcoding 1080p material with lots of effects will consume huge amount of processor resources. For example ~30min long project was transcoded to 1080p format in 5h. Regular DVD format needs only 3h to complete in AME-CS4. Is this time can be even shorter, with very low quality material (only for preview)?

  • Premiere Pro CS6 Generates HUGE file - Encoder settings help please

    Using PPCS6 to create a 6 minute AVI file. The source video is an AVI screen capture from Camtasia for an application that is spread across 3 widescreen monitors, making the screen/video resolution 5760x1200 with a frame rate of 30. I need to output the same resolution/aspect ratio (Camtasia will not do this, hence my use of Premiere).
    The initial screen capture is just under 2GB.
    The AVI output from Media encoder is 45GB which is just too big to use.
    Is there some settings I can use that will create a file of approximately the same size (under 3GB) and still look as sharp as the original capture?
    My current encoder settings are:
    Codec: Microsoft Video 1
    Quality: 90
    Width: 5760
    Height: 1200
    Frame Rate: 30
    Field Order: Lower First
    Aspect: Square Pixels (1.0)
    Depth: 8-bit
    Keyframe Interval: 8
    Optimize Stills checked.

    Camtasia files use their own TechSmith codec (TSCC) which is highly optimized for screen captures where hardly anything changes from frame to frame, and realistically you can't beat it with any of the default codecs, which are designed for full-motion video. With MV1 that file size is about what I'd expect from such a massive resolution. Also, do you really need 30fps? Most screencaps will look OK at 15 or even 12 at a push.
    You should be able to encode back to AVI/TSCC if you have Camtasia on the same machine as Prem, if not you can download the codec pack for free from Techsmith's website.

  • AME Taking Really Long Time To Open Encoding Settings

    With the release of the 2014 versions of AME, I have experienced really long wait times when opening the encoding settings for a job. For example, if I add a 1920x1080 image sequence to the encoder, pick Quicktime as the container and any of the available codecs, clicking on the codec name to open it's settings causes a really long delay, maybe 3 minutes, before the settings dialog will open. I am using a Macbook Pro with Yosemite. Previous versions before 2014 version never had this issue. Is this a known issue?
    thx

    This is a known issue with running AME on Yosemite. We are working with Apple on the issue and hope it will be fixed in an upcoming OS update.

Maybe you are looking for