I knew there was a reason I didn't really want to upgrade, but I did & now the FF15 won't display the htm which my old version did perfectly

Actually it does display the page, but it doesn't display some of the elements which 3.6 did perfectly & even lowly old IE9 still does
Where do I post the 2 screenshots? - the 1 of IE9? & the other of FF15? - which, it should be obvious, isn't displaying the blue lines down the sides

cor-el wrote:
Do you know what (CSS) code is responsible for those lines?
After you asked your question, I did some experimentation by varying
the size of the jpg displaying the long blue bar
& came to a startling conclusion
FF15 has changed its ability to display jpgs, if said jpg is even slightly greater
than 30K on its long (vertical) side
You see, the blue bar isn't generated by FF - it's an independent 8x35Kblubx.jpg,
an 8 x 35,000 pixel blue line, which was custom created in a drawing prg
I can send you the file if you want to see it, but the bottom line is,
the old version of FF used to display it perfectly & in virtually any paint type
or jpg display prg (preferably such as IrfanView or ACDSee etc),
it still will, but NOW, in FF15 it doesn't work
Thus whoever's responsible for finalizing the code at Mozilla/FF (whether it's a committee
or a person making a decision for a committee), they've decided some type of jpgs
just won't display, if they're greater than some arbitrary # of pixels
on its long (vertical) side
So, here it is ; even FF15 runs the HTM perfectly, *if* I restrict the 8x35Kblubox.jpg
to its shorter `brother', which is 8x30Kblubox.jpg
Why 30K is acceptable to FF15, but even 30.5K or certainly 34K isn't,
is completely upto whoever's responsible for deciding what will display on FF15
All right, why the change? - Even IE9 still displays the 35Kblubox
& all the way upto 60K & maybe more (I decided 60K was as big as I'd need
at the time they were created), but FF15 jams out at 30.5!
Clearly it's a FF15 `issue' & should be restored to its former ability to run at least 60K
pixel or greater jpgs (along the long upright edge)
frebe

Similar Messages

Firefox 29 sucks! There was NO REASON to change it. Now, I have to use IE! I hate IE!

Firefox 29 sucks! There was NO REASON to change it. Now, I have to use IE! I hate IE! It's slow , it crashes and does not work with Hotmail.
This is the next worst thing to happen since Outlook took over Hotmail.

You don't provide enough information. What's actually going on with Firefox?
Also, Outlook wasn't "taken over" by Hotmail, it was rebranded
*http://en.wikipedia.org/wiki/Outlook.com#Transition_to_Outlook.com

I can't remember my password even with hint. It was reset at the Boston Genius Bar when some work was done.. Didn't realize this til I got home and now. It's been 6 months since I was there. Suggestions? Thanks....mmh

I can't remember my password even with hint. It was reset at the Boston Genius Bar when some work was done.. Didn't realize this til I got home and now. It's been 6 months since I was there. Suggestions? Thanks....mmh

Assuming you have Lion, Mountain Lion, or Mavericks, restart and hold the Command and R keys. When the reboot has completed, click Utilities on the menu bar if the utilities window has not automatically opened. Click Terminal. When the Terminal window has opened, type exactly the following:
resetpassword
and press Enter.
When the Reset Password Window opens, select the internal storage, the user, and type a new password twice. Do not enter a hint. Click Save.
Accept the next window that opens, and back at the Reset Password window click the lower right button to accept the reset of the user's home directory permissions.
Click the apple left side of the menu bar, Restart and you will now have a new password.

Why do I get this error when trying to use my bluetooth headset as a listening device? There was an error connecting to your audio device. Make sure it is turned on and in range. The audio portion of the program you were using may have to be restarted.

Why do I get this error when trying to use my bluetooth headset as a listening device? There was an error connecting to your audio device. Make sure it is turned on and in range. The audio portion of the program you were using may have to be restarted.

I may have already resolved this issue buy removing the device from my computer and re-pairing it. It is currently working just fine.

I ordered my iPhone 5s in online and already received it. but there was supposed to be a $ 50 gift card with this, i haven't received it. how can i get the gift card?

I ordered my iPhone 5s in online and already received it. but there was supposed to be a $ 50 gift card with this, i haven't received it. how can i get the gift card?

Contact whomever you ordered the device from.
No one in these user to user support forums can assist with such issues.

During CS5 master collection update, I get the error "There was an error downloading this update. Please quit and try again later." This has been happening for the past few days. Can someone help me getting my updates?

During CS5 master collection update on Windows 7, 64-bit laptop, I get the error "There was an error downloading this update. Please quit and try again later." This has been happening for the past few days. Can someone help me getting my updates?

Since CS5 is from 4+ years before the Cloud, this is not the right forum... but I don't really know a correct forum for that very old product
Have you tried to manually update the individual programs?
All updates start here and select product, read to see if you need to install updates in number order, or if the updates are cumulative for the individual product http://www.adobe.com/downloads/updates/

When I bought my iPad there was a feature that allowed me to voice record reminders. What happened to this feature. With all the updates, it is now gone.

When I bought my ipad 2 a few years ago there was a feature so that I could record reminders. But with all the updates, this feature is now gone. What happened to it? Also, on my iphone and imac, I can dictate and it types for me. I thought I had this feature on the ipad too, but can't find it. Does it not exist for the ipad 2 or do I have to download an app?

Your Mac will need internet connection : http://support.apple.com/kb/HT5449
For your iPad there is Dragon Dictation which might work (I haven't tried it)

TS1367 I was having a problem down loading photos, so I force quite all programs. Then there was problem launching finder. Relaunched and turned computer off to reboot. Now computer starts, but does not boot up I am stopped at a white blank screen

I was having a problem down loading photos, so I force quite all programs. Then there was problem launching finder. Relaunched and turned computer off to reboot. Now computer starts, but does not boot up I am stopped at a white blank screen

Welcome to Apple Discussions Dathanb
You have posted in the Feedback About New Discussions forum.
As you are a first time poster, you seem to have missed the text at the top of this forum that says:
Please Read This Before Posting Here
If your question concerns a hardware or software technical issue, please do not post in this forum
Go to the main Apple Discussions page, select an appropriate product category and follow the links until you reach the correct forum for your post, then click the POST NEW TOPIC link. Because your post doesn't indicate was OS you are using on your iMac, I can't give you a link to the most appropriate forum.
Basically, though, the version of TechTool on the AppleCare disks is not compatible with newer versions of OS X and/or Macs (I can't remember which). If you don't get a satisfactory response by posting in the appropriate iMac or OS X forum, I suggest you take your iMac to the geniuses at the Apple Store. You can set up an appointment time for the same day online before you leave home.
Peggy

Hi I want to create a search form with drop down search criteria. This form should then search on the same site and display the search results. Is there HTML available for this? Or an oline site that I can use to build this form? I created a form in Jotfo

Hi I want to create a search form with drop down search criteria. This form should then search on the same site and display the search results. Is there HTML available for this? Or an oline site that I can use to build this form? I created a form in Jotform.com, but this form doesn't search the site, instead it sends me an e-mail. Do you have a solution for me? Thanks.

Hi I want to create a search form with drop down search criteria. This form should then search on the same site and display the search results. Is there HTML available for this? Or an oline site that I can use to build this form? I created a form in Jotform.com, but this form doesn't search the site, instead it sends me an e-mail. Do you have a solution for me? Thanks.

Adobe CS6 master Collection disks purchased with serial Nos and used for 18months ok but now I get told "Your Trial has expired" I was never aware it was a trial? purchase was from reseller slim.nl Adobe ID registers serial No but it is now described as i

adobe CS6 master Collection disks purchased with serial Nos and used for 18months ok but now I get told "Your Trial has expired" I was never aware it was a trial? purchase was from reseller slim.nl Adobe ID registers serial No but it is now described as invalid. What is going on?

Issues related to serial numbers and registration can never be handled on a public forum as this one is.
Please either call Customer Service for your region, or use web chat (link below). When using the link below, enter a product name and an issue. Ignore the provided links, and choose something like "Still have a problem?" and you'll get a link to web chat:
Contact Customer Care

Outlook 2007: There was a problem reading one or more of your reminders. Some of your reminders may not be displayed.

I have been banging my head on this one for a while.
I have run the /cleanfreebusy, /resetfolders, /cleanreminders on Outlook.exe
I moved all calendar items from all folders to a PST, then closed the PST.
I uninstall and reinstalled Office
I have looked for KB2412171 and one other KB that didn't apply (about Dynamics)
My last thought was to recreate the Windows profile, but that didn't work. It still came back.
After removing the calendar events, I just tried MFCMapi, but the Reminders table doesn't show ANY reminders! This would lead me to believe that I really did remove ALL reminders to the PST, and they aren't showing. Why then does it still say that
it can't display the reminders?
After using MFCMapi, I also connected to the server using Non-cached mode, saw that no reminders were present, so I got the bright idea to use non-cached mode for the client. This may or may not work over the long run, because she has 11000 items in her
inbox.
Any ideas?

Hi,
Have you finished pruning down the calendar items? If that fix the problem?
In addition, please have a look at this thread and check if it applies:
http://answers.microsoft.com/en-us/office/forum/office_2007-outlook/outlook-2007-there-was-a-problem-reading-your/01969b36-5c58-4677-9840-15bae96e292f
Best Regards,
Steve Fan
Forum Support
Come back and mark the replies as answers if they help and unmark them if they provide no help.
If you have any feedback on our support, please click
here

There was an error when I tried to install OS X Lion online. What can I do to fixed the problem?

There was an error when I tried to install OS X Lion after I purchased the os online. How do I fixed it?

Had the same problem. All I did was click retry, (nothing happened at first so had a panic attack) so I checked my email and found I'd payed for Lion, also the Lion App in the app Store had gone back to the purchace price. However after reaching for a brown paper bag to try and stop myself hyperventilating, Lion suddenly appeared and said it was installing. 33 minutes later it was up and running 'Job done'

Harddrive was replaced and now my computer won't recognize the IPOD

I recently had the hardrive replaced and now I can't seem to get it to charge, my itunes to recognize the ipod. I have tried several times restore and update. All I get is error messages "install wizard could not be completed" and "error in update manager". One thing...I have the IPOD with the color display and when I got it back and plugged it in (it worked long enough to download my music, but the display was in black and white. When I do get something on the screen it is a file with an exclaimation point and the www.apple.com/support/ipod website. HELP!!!!!

Hi,
A colour iPod without a workable system files, will display in play and white. I suggest that you should do a format first, before the Restore.
Please read the following for some suggestions
Hello,
If a sad iPod icon or an exclamation point and folder icon appears on your iPod’s screen, or with sounds of clicking or HD whirring, it is usually the sign of a hard drive problem and you have the power to do something about it now. Your silver bullet of resolving your iPod issue – is to restore your iPod to factory settings.
http://docs.info.apple.com/article.html?artnum=60983
If you're having trouble, try these steps at different levels one at a time until the issue is resolved. These steps will often whip your iPod back into shape.
Make sure you do all the following “TRYs”
A. Try to wait 30 minutes while iPod is charging.
B. Try another FireWire or USB through Dock Connector cable.
C. Try another FireWire or USB port on your computer .
D. Try to disconnect all devices from your computer's FireWire and USB ports.
E. Try to download and install the latest version of iPod software and iTunes
http://www.apple.com/ipod/download/
http://www.apple.com/itunes/download/
F. Try these five steps (known as the five Rs) and it would conquer most iPod issues.
http://www.apple.com/support/ipod/five_rs/
G. Try to put the iPod into Disk Mode if it fails to appear on the desktop
http://docs.info.apple.com/article.html?artnum=93651
If none of these steps address the issue, you may need to go to Intermediate level listed below in logical order. Check from the top of the lists to see if that is what keeping iPod from appearing on your computer in order for doing the Restore.
Intermediate Level
A. Try to connect your iPod with another computer with the iPod updater pre-installed.
B. Still can’t see your iPod, put it in Disk Mode and connect with a computer, instead of doing a Restore on iPod Updater. Go and format the iPod instead.
For Mac computer
1. Open the disk utility, hope your iPod appears there (left hand side), highlight it
2. Go to Tab “Partition”, click either “Delete” or “Partition”, if fails, skip this step and go to 3
3. Go to Tab “Erase” , choose Volume Format as “MAC OS Extended (Journaled), and click Erase, again if fails, skip it and go to 4
4. Same as step 3, but open the “Security Options....” and choose “Zero Out Data” before click Erase. It will take 1 to 2 hours to complete.
5. Eject your iPod and do a Reset
6. Open the iPod Updater and click “Restore”
For Window computer
Go to folder “My Computer”
Hope you can see your iPod there and right click on the iPod
Choose “Format”. Ensure the settings are at “Default” and that “Quick Format” is not checked
Now select “Format”
Eject your iPod and do a Reset
Open the iPod Updater and click “Restore”
In case you do not manage to do a “Format” on a window computer, try to use some 3rd party disk utility software, e.g.“Partition Magic”.
C. Windows users having trouble with their iPods should locate a Mac user. In many cases when an iPod won't show up on a PC that it will show up on the Mac. Then it can be restored. When the PC user returns to his computer the iPod will be recognized by the PC, reformatted for the PC, and usable again. By the way, it works in reverse too. A Mac user often can get his iPod back by connecting it to a PC and restoring it.
Tips
a. It does not matter whether the format is completed or not, the key is to erase (or partly) the corrupted firmware files on the Hard Drive of the iPod. After that, when the iPod re-connected with a computer, it will be recognized as an fresh external hard drive, it will show up on the iPod updater.
b. It is not a difficult issue for a Mac user to find a window base computer, for a PC user, if they can’t find any Mac user, they can go to a nearest Apple Shop for a favor.
c. You may need to switch around the PC and Mac, try to do several attempts between “Format” and “Restore”
http://discussions.apple.com/thread.jspa?messageID=2364921&#2364921
Advance Level
A. Diagnostic mode solution
If you have tried trouble shooting your iPod to no avail after all the steps above, chances are your iPod has a hardware problem. The iPod's built-in Diagnostic Mode is a quick and easy way to determine if you have a "bad" iPod.
You need to restart your iPod before putting it into Diagnostic Mode. Check that your hold switch is off by sliding the switch away from the headphone jack. Toggle it on and off to be safe.
Press and hold the following combination of buttons simultaneously for approximately 10 seconds to reset the iPod.
iPod 1G to 3G: "Menu" and "Play/Pause"
iPod 4G+ (includes Photo, Nano, Video, and Mini): "Menu" and "Select"
The Apple logo will appear and you should feel the hard drive spinning up. Press and hold the following sequence of buttons:
iPod 1G to 3G: "REW", "FFW" and "Select"
iPod 4G+ (includes Photo, Nano, Video, and Mini): "Back" and "Select"
You will hear an audible chirp sound (3G models and higher) and the Apple logo should appear backwards. You are now in Diagnostic Mode. Navigate the list of tests using "REW" and "FFW". The scroll wheel will not function while in diagnostic mode. For further details on Diagnostic mode can be found at http://www.methodshop.com/mp3/ipodsupport/diagnosticmode/
Try to do the 5in1, HDD R/W and HDD scan tests. Some successful cases have been reported after the running the few tests under the Diagnostic mode. In case it does not work in your case, and the scan tests reports show some errors then it proves your iPod has a hardware problem and it needs a repairing service.
B. Format your iPod with a start disk
I have not tried this solution myself, I heard that there were few successful cases that the users managed to get their iPod (you must put your iPod in disk mode before connecting with a computer) mounted by the computer, which was booted by a system startup disk. For Mac, you can use the Disk Utility (on the Tiger OS system disk), for PC user, you can use the window OS system disk. Try to find a way to reformat your iPod, again it does not matter which format (FAT32, NTFS or HFS+) you choose, the key is to erase the corrupted system files on the iPod. Then eject your iPod and do a Reset to switch out from Disk Mode. Reboot your computer at the normal way, connect your iPod back with it, open the iPod updater, and hopefully your iPod will appear there for the Restore.
If none of these steps address the issue, your iPod may need to be repaired.
Consider setting up a mail-in repair for your iPod http://depot.info.apple.com/ipod/
Or visit your local Apple Retail Store http://www.apple.com/retail/
In case your iPod is no longer covered by the warranty and you want to find a second repairing company, you can try iPodResQ at your own risk
http://www.ipodresq.com/index.php
Just in case that you are at the following situation
Your iPod warranty is expired
You don’t want to pay any service charges
You are prepared to buy a new one
You can’t accept the re-sell value of your broken iPod
Rather than leave your iPod as paper-weight or throw it away.
You can try the following, but again, only do it as your last resort and at your own risk.
Warning ! – It may or may not manage to solve your problem, and with a risk that you may further damage your iPod, which end up as an expensive paper weight or you need to pay more higher repairing cost. Therefore, please re-consider again whether you want to try the next level
Last Resort Level
1. . Disconnecting the Hard Drive and battery inside the iPod – Warning !! Your iPod warranty will be waived once you open the iPod.
In Hong Kong there are some electronic shops offering an iPod service for Sad iPod, the first thing they do is to open up the iPod’s case and disconnecting the battery and the Hard Drive from the main board of the iPod. Wait for 5-10 minutes and reconnecting them back. The reason behind which I can think of is to do a fully reset of a processor of the iPod. In case you want do it itself and you believe that you are good on fixing the electronics devices and have experience to deal with small bits of electronic parts, then you can read the following of how to open the iPod case for battery and HDD replacement (with Quicktimes)
http://eshop.macsales.com/tech_center/index.cfm?page=Video/directory.html
2.Press the reset button on the Hard Drive inside the iPod – Suggestion from Kill8joy
http://discussions.apple.com/thread.jspa?messageID=2438774#2438774
Have I tried these myself? No, I am afraid to do it myself as I am squeamish about tinkering inside electronic devices, I have few experiences that either I broke the parts (which are normally tiny or fragile) or failed to put the parts back to the main case. Therefore, I agree with suggestion to have it fixed by a Pro.
2. Do a search on Google and some topics on this discussion forum about “Sad iPod”
What should I do with my iPod? Send it or keep it?
http://discussions.apple.com/thread.jspa?threadID=469080&tstart=0
Strange error on iPod (probably death)
http://discussions.apple.com/thread.jspa?threadID=435160&start=0&tstart=0
Sad Face on iPod for no apparent reason
http://discussions.apple.com/thread.jspa?threadID=336342&start=0&tstart=0
Meeting the Sad iPod icon
http://askpang.typepad.com/relevanthistory/2004/11/meeting_thesad.html#comment-10519524
Sad faced iPod, but my computer won’t recognize it?
http://discussions.apple.com/thread.jspa?messageID=2236095#2236095
iPod Photo: unhappy icon + warranty question
http://discussions.apple.com/thread.jspa?messageID=2233746#2233746
4th Gen iPod Users - are we all having the same problem?
http://discussions.apple.com/message.jspa?messageID=2235623#2235623
Low Battery, and clicking sounds
http://discussions.apple.com/thread.jspa?messageID=2237714#2237714
Sad faced iPod, but my computer won’t recognize it
http://discussions.apple.com/thread.jspa?messageID=2242018#2242018
Sad iPod solution
http://discussions.apple.com/thread.jspa?threadID=412033&tstart=0
Re: try to restore ipod and it says "can't mount ipod"
http://discussions.apple.com/thread.jspa?threadID=443659&tstart=30
iPod making clicking noise and is frozen
http://discussions.apple.com/thread.jspa?messageID=2420150#2420150
I am not suggesting that you should follow as well, but just read them as your reference. You are the person to make the call.

My new iPad2 synched OK on initial setup but I didn't really want all the photos in iPhoto transferred so on later synch I tried limiting the sych to certain albums only to find that only a fraction of the albums now on the iPad. I tried synching again.

My new iPad2 set up OK with all the photos in my iPhoto transferring . On a later synch I tried limiting the transfer to only certain albums. After that I find only a fraction of the desired albums transferred. I tried synching again without any restrictions but get the same limited number of photos and albums. I think I've seen the solution to this fault somewhere - something to do with deleting the iPhoto cache but can't find it.

Update: I was unsuccessful on my attempt to delete the iPhoto Cache folder because I didn't follow the directions exactly. There seems to be more than one folder with an identical name. Finally succeeded in getting all my photos back on the iPad2.
If one desires to change the selection of photos snc'd, however, it apears that you must change the selecion from the iTunes screen while the iPad is plugged in and the select "Apply". Unfortunate, the sync starts immediately when you plug the iPad in and it doesn't seem to smart to stop the sync. It appears you have to make a change in iTunes while syncing. Let it complete. Detach the iPad. Go back and delete the iPhoto cache ad directed. Then the next time you sync presumably the new sync restrictions will apply. I didn't want to risk stopping the sync that started automatically to change the sync options and then direct it to sync again but that might work. Too bad we don't have more control over the starting of syn when the iPad is attached. Maybe we actually do but I haven't noticed it.

I submitted my information into the 'uptodate' program to download Lion OSX and it verified that I was able to get the upgrade but then nothing happened. How can I get the upgrade without having to pay for it?

When I tried to go back through and do it again, it gives me and error that says that my serial number has already been registered to the uptodate program and it wont allow me to continue any further. Is there a place I can go in my computer to find it and start the download? I got all the way to the point where I submitted my purchase (for free) and then as soon as I did that, nothing started...

Is this for a new MacBook Pro? If you are entitled to a free upgrade, but are having trouble with the Mac App Store and can't download Lion, call Applecare and explain the situation and see if they can help you. It's always possible that the Mac App Store has been extra busy lately and for some reason may not have processed your request properly.
First, though, check in your applications folder to be sure that the installer isn't already there. It's called "Install Mac OS X LIon.app". Step one is to download the installer. Step two is to run it. It will vanish from your Application folder after it runs, so if you want to make a copy of the installer, make one before you run it.
Good luck!

I knew there was a reason I didn't really want to upgrade, but I did & now the FF15 won't display the htm which my old version did perfectly

Similar Messages

Maybe you are looking for