I.m restoring my ipad 2 but my ipad won't respond what shall i do. only the apple logo is seen but wont respond to restoring
I"m restoring my ipad 2 but my ipad won't respond what shall i do. only the apple logo is seen but wont respond to restoring. please do help me email at [email protected]
FORCE IPAD INTO RECOVERY MODE
1. Hold Sleep/Wake button down and slide to turn off iPad
2. Turn on computer and launch iTune (make sure you have the latest version of iTune)
3. Plug USB cable into computer's USB port
4. Hold Home button down and plug the other end of cable into docking port. Do not release button until you see picture of iTune and plug.
5. Release Home button.
ON COMPUTER
6. iTune has detected iPad in recovery mode. You must restore this iPad before it can be used with iTune.
7. Select "Restore iPad"...
Similar Messages
-
I cannot open my ipad 2 after update to ios 7..only the apple logo keeps on displaying..please help..
Power-cycling or connecting to iTunes didn't fix the issue. However the iPad did restart, trying to install the update but it didn't complete and received a error once again. And now the iPad is stuck on the update screen with the progression bar beneath the apple.
The error reads, "The iPad could not be updated. An unknown error occurred (6)." -
What to do now when my iPad won't turn on after I turn it off. It shows only the apple logo. I am sure it has above 70% charge as when I sync my iPad it shows necessary detail in iTunes. I have tried, HOME & POWER button, but did not work.
First try a Reset ( No Data will be Lost )
Press and hold the Sleep/Wake button and the Home button at the same time for at least Ten seconds... (But can take Longer)... until the Apple logo appears. Release the Buttons
If no joy... Try a Restore...
1: Connect the device to Your computer and open iTunes.
2: If the device appears in iTunes, select and click Restore on the Summary pane.
Restoring > http://support.apple.com/kb/HT1414
Make sure you have the Current Version of iTunes Installed on your computer
iTunes free download from www.itunes.com/download
3: If Unable to Restore, try using the Steps in this article to force the device into Recovery Mode.
Note on Recovery Mode.
You may need to try this More than Once... Be sure to Follow ALL the Steps...
After you have Recovered your Device...
Re-Sync your Content or Restore from the most Recent Backup...
Restore from Backup > http://support.apple.com/kb/ht1766 -
i was updating my iphone 4 through settings but in the middle my phone switched offf n now what i can see is the apple logo blinking n i cant connect it to itunes can any1 help me?
If you have a backup of your information on your computer, I would suggest putting your phone into recovery mode, by holding down the home key and keeping it held down while you connect it by usb into your computer with itunes running. Keep the home button held down until it indicates recovery mode, and proceed with the restore.
-
My ipad2 is not responding..I want to restart it but i can get nothing but a black screen with only the apple logo and a small gear icon. It occasionally beeps but no other response. Any ideas as to what may be wrong and what I can do?
Try:
- iOS: Not responding or does not turn on
- If not successful and you can't fully turn the iPad fully off, let the battery fully drain. After charging for an least an hour try the above again.
- If still not successful that indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order. -
I clicked on "Erase all Content and Settings and now my ipad is not working, only the apple logo appears. how to i reset it back?
Some please show me how to reset it.Here is some information from Apple:
http://support.apple.com/kb/TS3274
http://support.apple.com/kb/HT4057 -
i have erased my all phone contact list and then the message comes that it will be deleted with in an hour. but now my phone is not starting and only the apple logo appears on the screen. what should i do now..!
That number is for an apple server in the UK that is used for iMessage activation. A hidden SMS is snet to that number when you turn iMessage on and is used to verify your phone number. I suggest you turn iMessage off. In settings/phone turn on dial assist. Check with your carrier to see if you can send an international SMS as you end that possibility to activate iMessage. Rest your phone (Hold down the Sleep/Wake button and the home button together until the apple logo appears (ignore the ON/OFF slider) then let both buttons go and wait for device to restart (no data will be lost).) then turn iMessage back on.
-
I am trying to upgrade my macbook pro to os x mavericks, but it has been on the reboot process for more than 2 hours. There is only the apple logo with the spinning ball thing. What should I do?
Hi there Candyleehoiman,
I would recommend taking a look at the troubleshooting steps found in the article below.
Mac OS X: Gray screen appears during startup
http://support.apple.com/kb/ts2570
-Griff W. -
I have restored my iphone 3gs after having only the apple logo, it took me through all the restore, a page saying 'congrats your phone is now unlocked', and allowed me to chose to set up from new or back up....yet still displays only the apple logo.
Restore as New...
Redownload your Purchased and Free Apps using the Apple ID you Originally used...
iPhone User Guide
http://manuals.info.apple.com/en_US/iphone_user_guide.pdf -
my iphone 4 doesnt wants to turn on. i tried every step i found to restart it.. and is not working..
i restored it with my mac.. and after that the apple logo is in the screen and in my computer says "waiting for iphone"
but is like that for hours and nothing happen. i really tried everything.. i have the most new version of itunes.. my comp is ok. everything is ok..
i dont know what else to do.. some help?First, to get the tray open. You need to push harder.
Secondly, Does it have a wall power plug? If the battery is dead, it's won't work. Try to charge it with the wall plug adopter and not through the computer. Some USBs don't put out power so, are you pluging it into a Powered USB?
Try these and let us know.
OH! If you got it wet, you may have ended it. Did you get it wet? You could try putting it in a bag of rice, and hope it works. -
Having resent my iPad using the Settings route, the Apple logo appeared onscreen and a line below it filled from left to right. When full, the device did nothing. I was able to switch it off and back on, only to see the same Apple logo and filled line. Even pressing the ON botton for a few seconds did nothing. The device is now inert, and I cannot access it. Please help!!!
Reset iPad and continue with Restore.
Hold down the Sleep/Wake button and the Home button at the same time for at least ten seconds, until the Apple logo appears
Note: Data will not be affected. -
What does it mean when the apple logo just stays on my iPad?
I turned off my iPad, but when I went to turn it back on, the apple logo just stays there. It's been there for 10 minutes, and hasn't gone away. Help please.
If reset doesn't work, you'll have to force your iPad into Recover Mode.
Recovery Mode
1. Disconnect the USB cable from the device, but leave the other end of the cable connected to your computer's USB port.
2. Turn off the device: Press and hold the Sleep/Wake button for a few seconds until the red slider appears, then slide the slider. Wait for the device to turn off.
3.While pressing and holding the Home button, reconnect the USB cable to the device. The device should turn on.
4. Continue holding the Home button until you see the "Connect to iTunes" screen. When this screen appears, release the Home button. iTunes should alert you that it has detected a device in recovery mode. Click OK, and then click Restore to restore the device.
Note: Data will be lost. You may have to repeat the above many times. -
Many Ipad im seeing has the Apple logo and other informations at the back of the Ipad but mine comes with just the Apple logo at the center of the back and no other information given underneath.Could this still be a real one from Aple or fake because mine only have the Apple logo at the back
As fas as. I know, all iPads should have a serial number on the back of the device. Even refurbs that have a new or replaced back should have a serial and model number engraved on it. I would tend to think that you got a bootleg device.
-
My iPad 2 screen reverted to and is stuck on the apple logo. Will not shut off.
My iPAD 2 reverted to and is stuck on the Apple logo. Cannot shut it down. Unable to reset. Suggestions?
FORCE IPAD INTO RECOVERY MODE
1. Turn off iPad
2. Turn on computer and launch iTunes (make sure you have the latest version of iTune)
3. Plug USB cable into computer's USB port
4. Hold Home button down and plug the other end of cable into docking port.
DO NOT RELEASE BUTTON until you see picture of iTunes and plug
5. Release Home button.
ON COMPUTER
6. iTunes has detected iPad in recovery mode. You must restore this iPad before it can be used with iTunes.
7. Select "Restore iPad"...
Note:
1. Data will be lost if you do not have backup
2. You must follow step 1 to step 4 VERY CLOSELY.
3. Repeat the process if necessary. -
I updated my ipad to ios 8 and now it just has the apple logo and it w3ont do anything
my ipad asked me to update and i did and now all i havve is the apple logo and it wont do anything else
FORCE IPAD INTO RECOVERY MODE
1. Turn off iPad
2. Turn on computer and launch iTunes (make sure you have the latest version of iTune)
3. Plug USB cable into computer's USB port
4. Hold Home button down and plug the other end of cable into docking port.
DO NOT RELEASE BUTTON until you see picture of iTunes and plug
5. Release Home button.
ON COMPUTER
6. iTunes has detected iPad in recovery mode. You must restore this iPad before it can be used with iTunes.
7. Select "Restore iPad"...
Note:
1. Data will be lost if you do not have backup
2. You must follow step 1 to step 4 VERY CLOSELY.
3. Repeat the process if necessary.
Maybe you are looking for
-
How to generate the sequential number in Javascript
Hi , I am facing one issue. I am adding the record to the underneath record and it works fine. But I have one problem there. I am having 10 records and adding one record between any of those records. I can able to reinitialize the index using xfa.for
-
Hello all, I have an iPhone that I have music on synched to a Windows PC. I just bought an iMac and want to synch my phone to the iMac instead. However, when I plug it in to synch, it wants to wipe my iPhone and use the music from the iMac (of whic
-
Hello XI Experts, I know that there were lot of blogs about edi scenarios in XI but I'm still a bit confused and I appreciate any help. I need to configure scenario where we receive EDI message VDA 4905 format through ISDN using OFTP protocol. As I
-
the way I have been getting files out of FCS is by right clicking and choosing ADD TO CACHE. We usually deal with 6 minute video clips so in a minute, you get the dot and you are ready to drag the file to your desktop. I have been told at work that t
-
Good afternoon. I am wondering if it is wise to try to get a "OK" version that will run on a G4 MDD, or just take the plunge and go to an Intel machine. I don't that the sound of that thought.....but it may be the new reality. Thanks for your time.