I pod not communicating properly

For some reason, while I was on a trip, my ipod stopped working, and whenever I did anything to it, it started blinking green and orange. When I brought it back to my computer, I turnes did not recognize it. I put in the I pod cd. the cd at least recognized my shuffle as an Ipod, and also recognized that it needed to be formatted. However when came the time to do so, it said it had trouble connecting with my Ipod shuffle, and could do nothing about it.
My computer recognizes the Ipod as a "removable disk", but whenever I try to do anythhing to it (I.e. open it), it freaks out and dies.
Please help!

Hi
just to say i have excatly the same problem
so your not alone
someone
please
help!!!!!!!!!!!!!!!

Similar Messages

WRT54G Not Communicating Properly.

Hello, Ever since I purchased my WRT54G I've been a victim of continuous disconnects from the internet. I've done several things to try and fix this, like change my broadcast channel multiple times as well as set up a secure network. After changing to channel 11 everything seemed to run smoothly for several weeks. Until lately I woke up one day and found all four of the Ethernet lights were solid green and the Power light was off. Ever since then the router has not been functioning correctly. I've gone as far as hitting the reset button and restarting the router. Now the lights all act properly, but I can't connect to the internet when I plug in my router. I can't even connect to the 192.168.1.1 admin page. When I look at my IP I see some strange arbitrary IP starting with 168. I don't know how to fix this and my family is very frustrated to have three computers that don't connect to the internet. I'd appreciate any help, both in getting my Router working and in stabalizing it so I don't have to suffer through this every week.

You need to reset the router to factory defaults, then setup the router again from scratch.
To reset your router to factory defaults, use the following procedure:
1) Power down all computers, the router, and the modem, and unplug them from the wall.
2) Disconnect all wires from the router.
3) Power up the router and allow it to fully boot (1-2 minutes).
4) Press and hold the reset button for 30 seconds, then release it, then let the router reset and reboot (2-3 minutes).
5) Power down the router.
6) Connect one computer by wire to port 1 on the router (NOT to the internet port).
7) Power up the router and allow it to fully boot (1-2 minutes).
8) Power up the computer (if the computer has a wireless card, make sure it is off).
9) Try to ping the router. To do this, click the "Start" button > All Programs > Accessories > Command Prompt. A black DOS box will appear. Enter the following: "ping 192.168.1.1" (no quotes), and hit the Enter key. You will see 3 or 4 lines that start either with "Reply from ... " or "Request timed out." If you see "Reply from ...", your computer has found your router.
10) Open your browser and point it to 192.168.1.1. This will take you to your router's login page. Leave the user name blank, and in the password field, enter "admin" (with no quotes). This will take you to your router setup page. Note the version number of your firmware (usually listed near upper right corner of screen). Exit your browser.
If you get this far without problems, try the setup disk (or setup the router manually, if you prefer), and see if you can get your router setup and working.
If you cannot get "Reply from ..." in step 9 above, your router is dead.
If you get a reply in step 9, but cannot complete step 10, then either your router is dead or the firmware is corrupt. In this case, use the Linksys tftp.exe program, located at:
ftp://ftp.linksys.com/pub/network
to try to reload your router with the latest firmware. After reloading the firmware, repeat the above procedure starting with step 1.
If you need additional help, please state your ISP, the make and model of your modem, your router's firmware version, and the results of steps 9 and 10. Also, if you get any error messages, copy them exactly and report back.
Please let me know how things turn out for you.

When I connect my I pod shuffle to USB it shows an error message - " I Tunes has deducted a problem with your audio configuration. Audio/Video playback may not operate properly" due to this problem each and every earphone am inserting goes unusable

When I connect my I pod shuffle to USB it shows an error message - " I Tunes has deducted a problem with your audio configuration. Audio/Video playback may not operate properly" due to this problem whenever i connect earphone each and every earphone gets un usable. Already made a factory reset. please arrange for a rectification.. :'(

Hi Ganeshpandianm,
Welcome to the Support Communities!
The article below may be able to help you with this issue.
Click on the link to see more details and screenshots.
iTunes for Windows: iTunes cannot run because it detects an issue with QuickTime
http://support.apple.com/kb/TS1371?viewlocale=en_US
"iTunes cannot run because it has detected a problem with your audio configuration"
Cheers,
- Judy

When I click on itunes, it tells me that thesoftware required for communicating with ipods and mobil phones was not installed properly. I have not changed anything on my computer so I'm not sure what I should do? Help

Help, When I click on itunes on my computer it tells me that the software required for communicating with ipods and mobil phone was not installed properly. I havent' changed anything. Does anyone know what I should do? Thanks

See the second box of Troubleshooting issues with iTunes for Windows updates.
tt2

One or more field types are not installed properly. Go to the list settings page to delete these fields. nativehr 0x81020014 /nativehr nativestack /nativestack

Hi ,
I am working in sharepoint 2013, This is a custom timer timer Execute method where i am moving a document item from one library to other once its expired,it was running fine and suddenly giving following error:-
One or more field types are not installed properly. Go to the list settings page to delete these fields.<nativehr>0x81020014</nativehr><nativestack></nativestack>
StackTrace = " at Microsoft.SharePoint.SPGlobal.HandleComException(COMException comEx)\r\n at Microsoft.SharePoint.Library.SPRequest.GetListItemDataWithCallback2(IListItemSqlClient pSqlClient, String bstrUrl, String bstrListName,
String bstrViewName, String bstrView...
I have filled all the meta data(site column) for the item but still same error, Please help me out as i have no clue why it is giving this error
public override void Execute(Guid targetInstanceId)
SPSecurity.RunWithElevatedPrivileges(delegate()
using (SPSite site = new SPSite(sourceUrl))
using (SPWeb web = site.OpenWeb())
//gets the document lib
SPList listFrom = web.Lists[sourceList];
//gets the expired documents items
SPQuery query = new SPQuery();
query.ViewFields = "<FieldRef Name='Expiration_x0020_Date'/>";
query.Query = @"<Where><Leq><FieldRef Name='Expiration_x0020_Date'/><Value Type='DateTime' ><Today /></Value></Leq></Where>";
SPListItemCollection items = listFrom.GetItems(query);
//if expired items found
if (items.Count > 0)
SPFile oFile = null;
foreach (SPListItem item in items)
string strfile = item.File.Name;
oFile = web.GetFile(sourceList + "/" + strfile);
//oFile.CopyTo("Archive/" + strfile);
oFile.MoveTo(destinationList + "/" + strfile);

Hi,
I think the issue is related to the internal name of the Expiration Day.
In the caml query code lines, we should use the right internal field name to retrieve and filter the list items.
To avoid such mistake, we can use the CAML Designer tool to generate the caml query code.
We can download the tool here: http://www.camldesigner.com/?p=594
Thanks & Regards,
Jason
Jason Guo
TechNet Community Support

Satellite P300D-110 integrated webcam is not functioning properly.

Hello everyone,
as the title says, the integrated webcam of my Toshiba Satellite P300D-110 is not functioning properly. Allow me to explain. Using the Camera Assistance Software I can take photo's and record music. If I try to record a video the preview screen turns up black and the end result tuns out black aswell, completely black.
Whenever I try to use my camera with applications such as MSN Live Messenger, Skype or at community websites using Firefox, Internet Explorer or Safari the application in question crashes.
*How did this happen?*
You tell me. This is how it went;
* Day 1: I've started up my laptop and looked at my fresh and clean install of windows vista home premium. I tried out my webcam using the webcam assistance software and it worked like a charm.
* Day 2: Once again I boot up my laptop and try to start my webcam only to find out that it no longer functions.
To give a quick summary of the thread;
* Using Camera Assistance Software provided by Toshiba I can take pictures.
* Using Camera Assistance Software provided by Toshiba I can record sound.
* Using Camera Assistance Software provided by Toshiba I can _*NOT*_ record or preview a video.
* I can not start my camera using any other application such as but not limited to; MSN Live Messenger, Skype, Mozilla Firefox, Internet Explorer and Safar.
* I have downloaded and isntalled the latest drivers from the Toshiba website.
* My laptop is about a week old.
I'm not sure what more I can do, all I want is for the webcam to work, if anyone can help me out please do so.
And if possible WITHOUT having to reinstall Windows Vista Home Premium.
I haven't even used it and wouldn't want to make that a solution for all the problems that might occur in the future.
Sincerely,
a sad customer.

Using Camera Assistance Software provided by Toshiba I can NOT record or preview a video.
Can you please describe the steps how you try to do this? I must ask you this because it runs well on my notebook. When the recording is finished player opens and you can see recorded movie. It is avi format and at the top of this player you can see the path where the movie is saved.
Most strange thing for me is that you cannot use it with Skype. Ok for MSN is not the perfect but there is absolutely no problem with Skype. Check the settings and it must work somehow.

WRT1900 AC V1 - Linksys is aware that the router is not working properly. Help spread the word.

I just had a conversation with Linksys' Customer Service via chat: Daphne L. J: Hello Fernando Paramo. My name is Daphne L..
Daphne L. J: Welcome to Linksys Global Chat. Is this your initial contact or do you have a case number?
You: Case number is 04971062
Daphne L. J: Please give me 3-5 minutes to pull up and review your case.
You: OK
Daphne L. J: Thank you.
You: I have a WRT1900 AC, V1. The router is not working properly. I have disconnections every few minutes.I already installed the new firmware version and I still have the same issues. I already reset the router to factory defaults and same issues. I have changed the settings back to my personal preferences: Changed the SSID, changed the wireless security settings, changed the DNS and deactivate WPS. That's it.I'm using 5 Ghz mode with my laptops (5 Ghz adapters) and 2-4 Ghz with a few devices (Chromecast, Nintendo 3DS).
Daphne L. J: Thank you for waiting.
Daphne L. J: Please confirm if the following information is correct:
Name : Fernando Paramo
Phone Number :
E-Mail Address :
Model Number : WRT1900AC
Serial Number : 13J10609406280
Country : United States
You: That's correct.
Daphne L. J: Okay. Were you able to check if the devices have stable connection wired to the router?
You: No. I do not have devices with Ethernet ports. Well, only the cable modem.
You: But the modem is fine. No disconnections from my ISP.
You: It is the router.
Daphne L. J: Alright. What is the current firmware version of your router?
You: I tried to return the router to Wal-Mart yesterday with no luck. This is a useless device. And I have been reading comments on the community forums and a lot of people are having problems.
Daphne L. J: We are actually aware of the issue and are working on a resolution. What is the current firmware version of your router?
You: Ver. 1.1.10.167514
You: Latest one.
Daphne L. J: Yes, so you reflashed the firmware, reset and then manually reconfigure it after, not using backup configuration, is that right?
You: That's correct.
Daphne L. J: And it is intermittent on all devices connected to both 2.4 and 5 Ghz networks, is that right?
You: That's correct.
Daphne L. J: Thank you for the information. Please give ,e 3-5 minutes to verify this with my superior.
Daphne L. J: Thank you for waiting.
You: I want to send you my WRT1900 AC and get a V2 or I want a EA8500 and pay the difference myseld.
You: I do not want my current hardware.
You: It is useless for my needs.
You: I can't believe I had an older E3000 that didn't give me any problems.
Daphne L. J: We have already exhausted all possible troubleshooting steps for your concern. As verified with my Supervisor, we will forward your case to our Customer Assurance Team. They are highly technical and knowledgeable when it comes to advanced troubleshooting. They will contact you in the next 24 to 48 hours. By the way, who is your Internet Service Provider? And do you Cable or DSL connection?
You: Cable connection.
Daphne L. J: Who is your Internet Service Provider?
You: A company called .
You: How are they going to contact me?
Daphne L. J: Alright. By the way, on the device itself, on its FCC ID, please check if you have WRT1900AC or WRT1900AC v2.
You: Are you paying attention to me?
You: I already told you it's V1.
Daphne L. J: They will call or email you. Please double check if these informations are correct:
Name :
Phone Number :
E-Mail Address :
You: I told you I want to send you my WRT1900 AC and get a V2 or I want a EA8500 and pay the difference myself.
You: I want them to contact me to my email. I can't answer the phone during work hours.
Daphne L. J: We can't assure you if we will be able to replace it with Version 2 or if you are allowed to have the EA8500 instead.
Daphne L. J: Just in case, do you also have an alternate number?
Daphne L. J: Also, what time zone are you in? And what is your preferred time and day for them to contact you?
You: I have the one from my office in Mexico. Central Time. Any time is good.
Daphne L. J: So, you are currently in Mexico?
You: I work in Mexico but I have the house in USA. I live in the border.
Daphne L. J: I see. Do you have any other questions or clarifications?
You: I live 10 minutes away from the International Bridge. But that's not an issue. I bought the router at Walmart in Laredo, TX.
Daphne L. J: Thank you for the information. Would that be all for now?
You: I want a clarification: Do you realize that there is an issue with the current WRT1900 AC? Are you aware of that?
You: Because this is a very expensive router that is not working as it should be.
Daphne L. J: Yes, we are aware of the issue and are working on a resolution.
Daphne L. J: Would there be anything else you need?
You: That would be it. I will wait for you to contact me.
You: Thanks.
Daphne L. J: Alright. Thank you for giving us an opportunity to serve you through Linksys Live Chat. You may also visit our support site at www.linksys.com. For your reference, your case number is 04980394. Thank you for choosing Linksys and have a great day! We paid $250 for this piece of equipment. That's a lot of money for a device that doesn't work. I just want to get a V2 replacement, or better yet, an exchange for a EA8500. We should all demand this. It is not fair for us. The current WRT1900 AC is a useless device. They even should do a recall of the product. I will wait for them to contact me, but I'm thinking if I should send the information to The Consumerist or someone else. What to do?

FernandoRocker wrote:
Well... instead of looking into this with Engineering, I would prefer you to talk about this with the Sales department and exchange my WRT1900AC for an EA8500 (I will pay the difference if needed). Seriously. The device is useless. Not just a paperweigt... an expensive paperweight.Actually I looking into the swap for you because I think that would be best in your case. Keep this in perspective. There is laterally millions of WRT1900AC V1 out there with very few issues with latest firmwares and of course the odd exception. In your case it could be a defective WRT1900AC.

WRT1900AC V1 - Linksys is aware that the router is not working properly. Help spread the word.

I just had a conversation with Linksys' Customer Service via chat: Daphne L. J: Hello Fernando Paramo. My name is Daphne L..
Daphne L. J: Welcome to Linksys Global Chat. Is this your initial contact or do you have a case number?
You: Case number is 04971062
Daphne L. J: Please give me 3-5 minutes to pull up and review your case.
You: OK
Daphne L. J: Thank you.
You: I have a WRT1900AC, V1. The router is not working properly. I have disconnections every few minutes.I already installed the new firmware version and I still have the same issues. I already reset the router to factory defaults and same issues. I have changed the settings back to my personal preferences: Changed the SSID, changed the wireless security settings, changed the DNS and deactivate WPS. That's it.I'm using 5 Ghz mode with my laptops (5 Ghz adapters) and 2-4 Ghz with a few devices (Chromecast, Nintendo 3DS).
Daphne L. J: Thank you for waiting.
Daphne L. J: Please confirm if the following information is correct:
Name : Fernando Paramo
Phone Number :
E-Mail Address :
Model Number : WRT1900AC
Serial Number : 13J10609406280
Country : United States
You: That's correct.
Daphne L. J: Okay. Were you able to check if the devices have stable connection wired to the router?
You: No. I do not have devices with Ethernet ports. Well, only the cable modem.
You: But the modem is fine. No disconnections from my ISP.
You: It is the router.
Daphne L. J: Alright. What is the current firmware version of your router?
You: I tried to return the router to Wal-Mart yesterday with no luck. This is a useless device. And I have been reading comments on the community forums and a lot of people are having problems.
Daphne L. J: We are actually aware of the issue and are working on a resolution. What is the current firmware version of your router?
You: Ver. 1.1.10.167514
You: Latest one.
Daphne L. J: Yes, so you reflashed the firmware, reset and then manually reconfigure it after, not using backup configuration, is that right?
You: That's correct.
Daphne L. J: And it is intermittent on all devices connected to both 2.4 and 5 Ghz networks, is that right?
You: That's correct.
Daphne L. J: Thank you for the information. Please give ,e 3-5 minutes to verify this with my superior.
Daphne L. J: Thank you for waiting.
You: I want to send you my WRT1900AC and get a V2 or I want a EA8500 and pay the difference myseld.
You: I do not want my current hardware.
You: It is useless for my needs.
You: I can't believe I had an older E3000 that didn't give me any problems.
Daphne L. J: We have already exhausted all possible troubleshooting steps for your concern. As verified with my Supervisor, we will forward your case to our Customer Assurance Team. They are highly technical and knowledgeable when it comes to advanced troubleshooting. They will contact you in the next 24 to 48 hours. By the way, who is your Internet Service Provider? And do you Cable or DSL connection?
You: Cable connection.
Daphne L. J: Who is your Internet Service Provider?
You: A company called .
You: How are they going to contact me?
Daphne L. J: Alright. By the way, on the device itself, on its FCC ID, please check if you have WRT1900AC or WRT1900AC v2.
You: Are you paying attention to me?
You: I already told you it's V1.
Daphne L. J: They will call or email you. Please double check if these informations are correct:
Name :
Phone Number :
E-Mail Address :
You: I told you I want to send you my WRT1900AC and get a V2 or I want a EA8500 and pay the difference myself.
You: I want them to contact me to my email. I can't answer the phone during work hours.
Daphne L. J: We can't assure you if we will be able to replace it with Version 2 or if you are allowed to have the EA8500 instead.
Daphne L. J: Just in case, do you also have an alternate number?
Daphne L. J: Also, what time zone are you in? And what is your preferred time and day for them to contact you?
You: I have the one from my office in Mexico. Central Time. Any time is good.
Daphne L. J: So, you are currently in Mexico?
You: I work in Mexico but I have the house in USA. I live in the border.
Daphne L. J: I see. Do you have any other questions or clarifications?
You: I live 10 minutes away from the International Bridge. But that's not an issue. I bought the router at Walmart in Laredo, TX.
Daphne L. J: Thank you for the information. Would that be all for now?
You: I want a clarification: Do you realize that there is an issue with the current WRT1900AC? Are you aware of that?
You: Because this is a very expensive router that is not working as it should be.
Daphne L. J: Yes, we are aware of the issue and are working on a resolution.
Daphne L. J: Would there be anything else you need?
You: That would be it. I will wait for you to contact me.
You: Thanks.
Daphne L. J: Alright. Thank you for giving us an opportunity to serve you through Linksys Live Chat. You may also visit our support site at www.linksys.com. For your reference, your case number is 04980394. Thank you for choosing Linksys and have a great day! We paid $250 for this piece of equipment. That's a lot of money for a device that doesn't work. I just want to get a V2 replacement, or better yet, an exchange for a EA8500. We should all demand this. It is not fair for us. The current WRT1900AC is a useless device. They even should do a recall of the product. I will wait for them to contact me, but I'm thinking if I should send the information to The Consumerist or someone else. What to do?

Hello. I sent my WRT1900AC V1 to Linksys four days ago (Monday) via UPS with a RMA. Linksys paid the shipping and everything. The router is still in route, and it should arrive to their offices tomorrow. Once they receive the WRT1900 AC V1, they are going to send me an EA8500 as a replacement. But I have been reading the comments about the EA8500 here in the forum and it seems to have the same problems. I guess the firmware is extremely flawed in both routers (maybe it is almost the same code?). Anyway, I will try the EA8500 and I hope it works. I bought a temporary router from Walmart and I paid $35 for it. It is a Belink N600 DB. I can't believe that a $35 router is working a lot, lot, lot better than my previous $250 WRT1900AC router. Unbelievable. If the EA8500 doesn't work, I'm going to try and get my money back from Linksys, or contact The Consumerist or someone to get my money back and get a Nighthawk instead.

Copy Function is Not Working properly In Order Management

Hi,
Description-
When an order with remnant model is copied, it copied only the topple model line and they include items attached to the top model line. It doesn’t copy the
option class lines and the option item lines (unshipped and shipped).
Example-
Enter an order with for pd-pto-model. See order#21231.The ordered quantities and structure of the model is shown below:
pd-pto-model 5 qty
pd-std-item1 (included item) 5 qty
pd-pto-oc (option class) 5 qty
pd-std-item1 (included item with rfr checked) 5 qty
pd-std-item2 (option item with rfr checked) 5 qty
pd-std-item3 (option item) 5 qty
Booked the order and pick relased the order. While shipconfirming only shipped 5 qty of pd-std-item3 and staged the rest. On querying the sales order, the line status is seen correctly as follows:
pd-pto-model Closed
pd-std-item1 (included item) Picked
pd-pto-oc (option class) Closed
pd-std-item1 (included item with rfr checked) Picked
pd-std-item2 (option item with rfr checked) Picked
pd-std-item3 (option item) Partially Interfaced to receivables
Copied this order from the order header. The new order# is 21232.On querying the order, I see only 2 lines as follows:pd-pto-model.
Anyone can help me on this issue.
Thanks,
Chinna

haisrig wrote:
Hi ,
We are facing an issue with select() in Solaris 10. we had written a sample program to this issue.
Program name :- sel.cpp
int main()
struct timeval sleeptime;
sleeptime.tv_sec = 60;
printf("1\n");
select(0,NULL,NULL,NULL,&sleeptime);
printf("2");
return 0;
When i run this program in Solaris 9, its printing 1 and after one minute its printing 2.
When i run this program on Solaris 10, its printing 1 and 2 without waiting for 60 seconds.
When i tried to print tv_usec, its printing as 0 in solaris 9 and some garbage values in solaris 10.
I think because of that the above select function is not working properly in solaris 10.
Why the tv_usec is not taking 0 as default values in Solaris 10?
We are using our legacy code for past 20 years. So, before going to do any changes we are trying to find why this happenig like this.Hi
It sounds to me that you've been lucky for 20 years then.
Local POD variables on the stack that aren't explicitly initialized can contain any value. Here's what I see in your app with dbx
(dbx) run
Running: sel
stopped in main at line 9 in file "sel.cpp"
    9      sleeptime.tv_sec = 60;
(dbx) print sleeptime
sleeptime = {
    tv_sec = -4198732
    tv_usec = 0
}That's on a Solaris 10 SPARC machine. If I try it on a Solaris 10 x86 box then I get
(dbx) print sleeptime
sleeptime = {
tv_sec = -830490588
tv_usec = 134510556
and I see the behaviour that you describe.
Paul

Select() function is not working properly in solaris 10.

Hi ,
We are facing an issue with select() in Solaris 10. we had written a sample program to this issue.
Program name :- sel.cpp
int main()
struct timeval sleeptime;
sleeptime.tv_sec = 60;
printf("1\n");
select(0,NULL,NULL,NULL,&sleeptime);
printf("2");
return 0;
When i run this program in Solaris 9, its printing 1 and after one minute its printing 2.
When i run this program on Solaris 10, its printing 1 and 2 without waiting for 60 seconds.
When i tried to print tv_usec, its printing as 0 in solaris 9 and some garbage values in solaris 10.
I think because of that the above select function is not working properly in solaris 10.
Why the tv_usec is not taking 0 as default values in Solaris 10?
We are using our legacy code for past 20 years. So, before going to do any changes we are trying to find why this happenig like this.
Thanks a lot.
Regards,
Srikanth.

haisrig wrote:
Hi ,
We are facing an issue with select() in Solaris 10. we had written a sample program to this issue.
Program name :- sel.cpp
int main()
struct timeval sleeptime;
sleeptime.tv_sec = 60;
printf("1\n");
select(0,NULL,NULL,NULL,&sleeptime);
printf("2");
return 0;
When i run this program in Solaris 9, its printing 1 and after one minute its printing 2.
When i run this program on Solaris 10, its printing 1 and 2 without waiting for 60 seconds.
When i tried to print tv_usec, its printing as 0 in solaris 9 and some garbage values in solaris 10.
I think because of that the above select function is not working properly in solaris 10.
Why the tv_usec is not taking 0 as default values in Solaris 10?
We are using our legacy code for past 20 years. So, before going to do any changes we are trying to find why this happenig like this.Hi
It sounds to me that you've been lucky for 20 years then.
Local POD variables on the stack that aren't explicitly initialized can contain any value. Here's what I see in your app with dbx
(dbx) run
Running: sel
stopped in main at line 9 in file "sel.cpp"
    9      sleeptime.tv_sec = 60;
(dbx) print sleeptime
sleeptime = {
    tv_sec = -4198732
    tv_usec = 0
}That's on a Solaris 10 SPARC machine. If I try it on a Solaris 10 x86 box then I get
(dbx) print sleeptime
sleeptime = {
tv_sec = -830490588
tv_usec = 134510556
and I see the behaviour that you describe.
Paul

9810 funtions and screen not working properly.

HI all, hoping to find some help here. My 9810 is acting up. None of the keys are working, even the 5 below the screen. Sometimes the track pad works but not when it is pressed, and when the back botton works it puts me into sreach mode and looks for the letter "H" only. The touch screen is fine. This was before upgrading to OS7.1. I have done multiple hard resets and it does nothing at all. This has been going on for three days now. It hasn't be dropped or anything.
Last night I upgraded to OS 7.1 now my back ground does not rotate properly with how the phone is being held it does rotate, When you hold it upright it thinks its on it's side and vise versa.
Has anyone had a similar problem, and how can I fix it? Or is it one of those ones when you just get a new phone. I have only had it since Feb 29, 2012
Thanks

Hello Champi,
Welcome to the BlackBerry Support Community.
The following article will assist regarding the issue you are experiencing with the keyboard and trackpad on your BlackBerry® Torch™ 9810 smartphone:
Trackpad, trackball, or keyboard not working on a BlackBerry Smartphone - http://www.blackberry.com/btsc/KB29640
We hope this helps.
Thank you.
-FB
Come follow your BlackBerry Technical Team on Twitter! @BlackBerryHelp
Be sure to click Kudos! for those who have helped you.
Click "Accept as a Solution" for posts that have solved your issue(s)!

I-Pod not recognized

Whenever I plug my I-Pod Photo into my laptop with Vista, I get told the USB Device is not recognized. Any ideas on what I can do? As of right now my laptop is the only computer I have at college, and I'd rather not have to wait until I can get my desktop sent.

See if any of these articles help.
Windows XP cannot detect an iPod.
USB drivers are not installed properly or are out of date.
iTunes 7 doesn't recognize the iPod.
iPod not recognized on a Windows laptop.

I-pod not recognized by Computer

Hello, everyone. I've had my 80G classic for about two years and last week bad things happened. When I plugged in my I-pod it said that this device could work better using USB 2.0. I thought that this was weird but didn't think much of it.( My I-pod had been using USB 2.0 for a few months on this computer) then the next day. It stopped connecting at all and says that this device can not be recognized. I have turned off my PC and tried pulling the power cord out. I've tried reinstalling my drivers. The funny thing is that I can still charge my I-pod with fire-wire and it works normal besides this.

That sounds like something strange may have happened to your USB drivers, lichu.
In the course of your troubleshooting to date, have you worked through the following document?
[iPhone or iPod is not recognized properly by computer when USB drivers are not installed properly or are out of date|http://support.apple.com/kb/TS1538]

My itunes match will not sync properly

Mac User same thing
Hello there here is my problem. My itunes match will not sync properly. It shows a lot of songs over 100 with the icloud match status as "Waiting"
Here is what i have done
1. Reinstall the entire OS delete everything and start from scratch
2. Turn on and off itunes match.
3. Hold down the option key
4. Move my music out of the music folder clear everything out of my itunes and bing back my music.
5. Use backup copies of my music in case the music files had been corrupted.
6. Checked numerious mac community forms that report simular issues.
7. Tried another macbook pro that I have
8. My wifes account which has about 8000 songs did no have the issue. My account seems to have the issue sobeservices2. I beleive this to be account specific. My account has 11481 songs and about 100 to 100 show with the status of "waiting"
9. I get no error messages
10. I've tried multiple ISP - COMCAST - FIOS - I even tried multiple computers
11. Redid the entire os
12. My account has problems "*****s2" but my wife account does not
13. Replicated the issue on more then one computer it seems only has problems with my itunes account. Suck waiting to upload
and its not always the same songs sometimes it's different songs that it gets suck waiting to upload.
14. Removed the waiting songs and attempted again
15. Started with fresh iTunes had the server match a blank itunes folder to the point where it said "0 Songs Match" then re-added them
16. Called Apple Care and spoke with a Senior Advisor who told me he would have to escalate a ticket and he to thought I had done all the tsing possible and that it was up to the engineers to figure out a solution.
I have been working on this for about 4 weeks now. All my trouble shooting has pointed it to be an account specific issue.
Any advise from the community

Hi
I have had a similar set of issues. 8000 songs, 800 in waiting. All ripped from CD into Apple Lossless - mainly classical so most didn't match directly.
First I ripped all these 8000 songs for my father first on his laptop from his CD collection. Eventually got them all matched or uploaded to his Match account (except one) by the usual tricks people suggest (e.g. recoding as AIFF or MP3 etc, deleting, re-adding blah blah). Though of course I shouldn't really have to waste my time doing this. One song absolutely refused to upload. Tried everything - including buying a pristine downloadable version off the publisher's website. Still resolutely refuses to upload.
Anyway - main problem is now with my PC. I copied all these 8000 tracks over. Re-installed everything etc. 800 remain in "waiting" (even though they uploaded Ok on a different account). When I rip my own CDs even some common stuff (e.g. Bowie/Stones) gets uploaded instead or matched and often with one or two tracks stuck in 'waiting'.
If I then look at my IPad (with Match enabled), it will show these waiting tracks as if they were already downloaded to it (which of course they are not). If I try and play one of them it just skips over it.

Hi, recently i bought macbook pro with retina display and installed windows 8 professional original software also. but in windows 8 track pad is not working properly. can you help me with providing drivers for trackpad to work on windows 8 professional .

hi, recently i bought macbook pro with retina display and installed windows 8 professional original software also. but in windows 8 track pad/ TOUCHPAD is not working properly. can you help me with providing drivers for trackpad to work on windows 8 professional .

Did you download and install the Windows Support software? If you did, did you use the Boot Camp Control icon to set up the trackpad how you want it?
http://www.apple.com/support/bootcamp/
https://discussions.apple.com/community/windows_software/boot_camp

I pod not communicating properly

Similar Messages

Maybe you are looking for