I put my iPod on my cable box USB to charge it and listen to music and when I plug it into my wall charger it doesn't connect. Please help idk what to do.
I'm able to plug it into my ps3 and the computer and it works, but when I plug it into the wall charger it doesn't work. I charged it with my wall charger all day but as soon as I connected it to my cable box it it only works with USB ports now. help me
I used it earlier that day. And I have an hd tv with USB port and it won't charge on that as well it. It works for my friends ipod tho and my charger does too
Similar Messages
-
I have a ipod touch 4th gen and it wont chrage. When you plug it into the wall the lightniing bolt screen will apear but no matter how long you leave it, it will never turn on. Also it the lightning bolt screen wont even come on when you plug it into a computer (PC)..........PLease help its been like this for forever
Hi Gammer576775!
Here is an article that will help you troubleshoot this issue with your iPod touch:
iPod touch: Hardware troubleshooting
http://support.apple.com/kb/ts2771
Will not power on, or will not turn on unless connected to power
Verify that the Sleep/Wake button functions. If it does not function, inspect it for signs of damage. If the button is damaged or is not functioning when pressed, seek service.
Connect the iPod touch to an Apple USB power adapter and let it charge for at least ten minutes.
After at least 15 minutes, if the display turns on and…
The home screen appears, the device should be working. Continue charging it until it is completely charged and you see this battery icon in the upper-right corner of the screen: . Then disconnect the device from power. If it immediately turns off, seek service.
The low-battery image appears even after the iPod touch has charged for at least 20 minutes: See the "iPod touch displays the low-battery image and is unresponsive" symptom in this article.
Something other than the Home screen or low-battery image appears , continue with this article for further troubleshooting steps.
If the iPod touch did not turn on, reset it while connected to an Apple USB power adapter. If the display turns on, go to step 4.If the display remains black, go to the next step.
Restore the device. Connect it to a computer and open iTunes. If iTunes recognizes it and indicates that it is in recovery mode, attempt to restore the iPod touch. If the device doesn't appear in iTunes or if you have difficulties in restoring it, see this article for further assistance.
If restoring the iPod touch resolved the issue, go to step 4. If restoring it did not solve the issue, seek service.
Thanks for using the Apple Support Communities!
Cheers,
Braden -
I went to turn on my iPod Touch one day and the screen went white. Tried resetting and got nothing. Tried plugging in to usb port and got nothing. Neither the computer nor iTunes recognizes my device. What do I do now?
By resetting did you see the apple logo? Try pressing and holding the on/off and home buttons simultaneously until the screen goes blank (black) and you see the apple logo. It should take about 10-15 seconds to reset.
-
My mini ipod appears off and not respond to any commands when pressed the buttons to reset, apple logo appeared and then the apple support site and it shuts down. already tried all the steps, but none worked, and when I plug it into my computer it does not appear in the iTunes bar. what do I do?
If MacKeeper corrupted the Recovery partition then even I underestimated its potential for damage. Garbage "cleaning" apps will cause misery but I have not found that the Recovery partition to have been affected by using MacKeeper or anything like it. I doubt that it did so, but I have learned not to underestimate the potential for such things to result in system corruption.
Before concluding your Mac has a hardware failure, try booting OS X Internet Recovery by holding command option r on startup (three fingers). That will force your iMac to bypass the Recovery partition altogether, and convey the ability to create a new one.
An Internet connection will be required (wired or wireless).
At the Mac OS X Utilities screen, select Disk Utility. Select your startup volume (usually named "Macintosh HD") and click the Repair Disk button. Describe any errors it reports in red. If Disk Utility reports "The volume Macintosh HD appears to be OK" in green then you can be reasonably (though not completely) assured your hard disk is in good working order.
Assuming the HD remains usable you can then use Disk Utility to erase it. Reinstall OS X, restore your essential software and other files, and don't reinstall the junk. -
So, I bought the iPod shuffle and when I plug it into my mac, the option of syncing doesn't appear. What do I do?
Does the Shuffle appear ini Tunes at all? If not try using a different USB port and double checking to make sure the other end of the syncing cable is firmly seated in the Shuffle.
B-rock -
What does it mean when my Ipod shows me an itunes icon but doesn't let me go to my home screen AND when I plug it into my Macbook it tells me my Ipod is in recovery mode AND will not be restored!?!?!?! HELP!!!
. . . sparse bundle could not be accessed (error -1)
-
I just factory restored my iPod 5 touch and when I plug it into iTunes to back it up, iTunes stops responding and closes. This only occurs when the iPod is plugged in, when it isn't, iTunes works fine. I am using Windows 8 and iTunes is updated (as of this posting). Any suggestions on getting around this? Thank you.
Also, when I put it through the Windows diagnostic, it lists an "incompatible program" WHILE my iPod is plugged in.
-
i was trying to update/restore my ipod and now i plug it in and it stays frozen on the usb to itunes picture. and when i plug it in it dosnt come up in itunes how do i fix this? any suggestions are appreciated
Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar -
ive just updated my ipod touch 4th gen, but the bat went flat now its just a white screen and when i plug it into my laptop nothing happenes
Hello,
This will fix your problem!
To put the device in DFU mode,
1. Connect the device to iTunes
2. Hold both the power button and the home button down simultaneously
3. After 10 seconds, release the power button but leave the home button pressed
4. iTunes should then recognize that the device has entered DFU mode and ask to restore.
That should get you back on your way.
~Lt. Leviathan -
I just bought a new ipod touch and when i plug it into my Mac usb port nothing is happening I can get the computer to sync other ipod in the same port
Try:
iPhone, iPad, iPod touch: Device not recognized in iTunes for Mac OS X
Do not omit the Additional Information paragraph.
Is the iPod that connects an iPod touch? If not that does not mean anything since iOS devices like iPod touch, iPhone and iPad use different drivers than other iPods. -
when i try to download an apps a message error 1009 appear ,please help me,what i have to do
plishing/scam. I would go to Settings>Safari and Clear Cookies. Data and History and not go to that site for a while. Seems like an infected site.
See this previous discussion on same symptom
https://discussions.apple.com/thread/6042028?tstart=0 -
For some reason when I plug my ipod into my comp itunes freezes but my ipod says it is plugged and when I plug it into a different comp it works. How can I fix this?
Setesh, See if both computer has the same version of iTunes, if both are the same, then it is your PC, that has plug-ins which is in conflict it iTunes. ( normally it is the Antivirus or some plug-ins to beautify your screen)
If it is different, most likely the other PC has an older version of iTunes, so you should downgrade your iTunes to that older version, which your iPod interface well with.
Other probable causes,
you are using the USB 1.1 port at the front of your PC, and not the USB2,0 port at the back of your PC. so switch to the back.
Dont use any other USB devices, when you are syncing the iPod.
Dont use any USH Hub.
Have a nice day! -
My iphone went blank and when I plugged it into outlet the screen shows the itunes logo and a picture of what looks like the charger. I tried to reset it and it does not respond. Can anyone help?
That screen means it has gone into recovery mode. You need to connect to a computer running iTunes by following the instructions in http://support.apple.com/kb/HT1808 for the procedure of recovery mode connection.
-
Hey,
I just tried redeeming my software online. I went through the whole process, got the password, and proceeded to get the software to download. But soon after, the wifi connection was disconnected, and when I tried to connect the ethernet cable, the entire software had disappeared from my launchpad. When I tried to restart the download, it kept saying that the password had already been used before, and that it could only be used once per computer. What do I do now?You shouldn't have to re-enter the code, Lion should be on your purchases list so you can re-download it. In the App Store, click Purchases... do you see ML there?
-
please help my ipod out of this rebooting loop the update doesnt work
as in the loop it shows the apple logo on the screen and right as it gets out of reboot it flashes white and goes back to the apple logo and does it none stop its not in DFU mode because ive tried, and by it quits it has to update before i can restore and in the middle of the update it gives me a notification with a number on it the number is really long and has alot of 0's and i think one 7 so i hope that help your question for my question
Maybe you are looking for
-
I can't see some files, or videos, in web, I can't download adobe player
-
Does "Run VI" invoke node work on strict references to REENTRANT VIs?
I am using LV 6.02 on Windows 2000. I am trying to use the "Run VI" invoke node method with a reference to a Reentrant VI, with no success. (It works when VI is not reentrant. Perhaps there is a reason this cannot work. But if not, I wonder if there
-
Hallo, PSE 13 hat Probleme bei mehreren Akionen hintereinander, stapeln von 2 Fotos, versehen mit Tags, löschen, verschieben in Kataloge, sowie beim integrieren von im Editor bearbeiteten Fotos im Organizer. es sind lange Wartezeiten nötig um die näc
-
Pre-populate a multi-valued attribute on target?
Hi. I am working on pre-populating our I-Planet target resource with data we are storing in OIM User(Address data). it is a requirement by the AD group to store the data as a multi-valued attribute in the LDAP attribute postaladdress. I have tried se
-
Intel Lights Out Management Config
Ok, there are some pretty intelligent folks here, so I need to find someone who not only knows how to make LOM work, but who also know how to explain it to someone who is not a unix guru or in other words, simple step by step instructions. I've just