Increment and decrement to reach upper and lower limit
I have to simulate a central heating system. A heater is turned on, room temp rises to 'upper limit'; heater is turned off when upper limit is reached. When heater is off, temp drops until lower limit is reached then heater is turned on again. I'm scratching my head!! have tried various case structures but cant get it to run continually. Whats the best way to do this? PS, im a noob! :-)
Use a shift register to keep the current heater state (since you only want the state to change when you go outside of the limits). From there, the Select function helps keep things straight.
There are only two ways to tell somebody thanks: Kudos and Marked Solutions
Unofficial Forum Rules and Guidelines
Attachments:
Heater control.png 12 KB
Similar Messages
-
Tolerance key PP - Lower limit
We have configured tolerance key PP with lower limit of 0$ for both absolute and percentage. When I try to post the invoice with a lower price, I receive a warning message that the price is too low (which is correct).
The problem is that when I try to post this invoice, it is getting posted without being blocked. Since the lower limit is defined, shouldn't the invoice be blocked when it is below lower limit defined.
Is there any other setting that I need to make to ensure that the invoice is getting blocked when it is posted below the lower limit defined? Please help. Thanks.Thanks to both of you! Here are the limits that I defined:
Price variance
Absolute lower limit
Check limit X Value 0,00
Absolute upper limit
Check limit X Value 0,00
Percentage lower limit
Check limit X Value 0,00
Percentage upper limit
Check limit X Value 0,00
Based on the limits defined, an invoice should be blocked when it exceeds either upper or lower limit. The upper limit is working fine. However, the lower limit is not causing the invoice to block.
Eg: PO net price is $100. I post an invoice with price $50. This lower price is not causing the invoice to block. -
The plus(+) and minus(-) keys to increment or decrement the date
Hi All,
I have a date field in which I would like to have the + and - keys to increment or decrement the date as in some windows programs.
Thank you, BillHi Chad, Yes I know the Date Picker... that is what it has now.
My users are keyboard users... hitting the plus or minus sign in the Num Pad is much quicker if the date is only 2-3 day plus or minus...
We desire to have the Date Picker and have maybe a onkey event call. I was hoping to find someone that has used "onkey" for a specific element/field so it doesn't look at every key stroke in the document but just the one date element onkeyup etc......
Thanks for the response.
Bill -
What is the significance of Safety Upper Limit and Lower Limit
Hello Experts,
I was trying to create a generic datasouce in rso2 , while setting the delta specific field I have selected date field and I need to know the significance of other two input fields provided over there:
Safety Interval Upper Limit.
Safety Interval Lower Limit.
and check box Real Time Enable.
Thanks,
VijayHi Vijay
Safety Interval Upper Limit of Delta Selection This field is used by DataSources that determine their delta generically using a repetitively-increasing field in the extract structure. The field contains the discrepancy between the current maximum when the delta or delta init extraction took place and the data that has actually been read. Leaving the value blank increases the risk that the system could not extract records arising during extraction. Example: A time stamp is used to determine the delta. The time stamp that was last read is 12:00:00. The next delta extraction begins at 12:30:00. In this case, the selection interval is 12:00:00 to 12:30:00. At the end of extraction, the pointer is set to 12:30:00. A record - for example, a document- is created at 12:25 but not saved until 12:35. It is not contained in the extracted data but, because of its time stamp, is not extracted the next time either. For this reason, the safety margin between read and transferred data must always be larger than the maximum length of time that it takes to create a record for this DataSource (with a time stamp delta), or it must display an interval that is sufficiently large (for determining delta using a serial number). Safety Interval Lower Limit This field contains the value taken from the highest value of the previous delta extraction to determine the lowest value of the time stamp for the next delta extraction. For example: A time stamp is used to determine a delta. The extracted data is master data: The system only transfers after-images that overwrite the status in the BW. Therefore, a record can be extracted into the BW for such data without any problems. Taking this into account, the current time stamp can always be used as the upper limit when extracting: The lower limit of the next extraction is not seamlessly joined to the upper limit of the last extraction. Instead, its value is the same as this upper limit minus a safety margin. This safety margin needs to be big enough to contain all values in the extraction which already had a time stamp when the last extraction was carried out but which were not read. Not surprisingly, records can be transferred twice. However, for the reasons above, this is unavoidable. these are used to determining the delta in a datasource: 1. Time stamp - The field is a DEC15 field which always contains the time stamp of the last change to a record in the local time format. 2. Calendar day - The field is a DATS8 field which always contains the day of the last change. 3. Numerical pointer - The field contains another numerical pointer that appears with each new record .
also dwload this How to Generic Delta doc https://www.sdn.sap.com/irj/servlet/prt/portal/prtroot/docs/library/uuid/84bf4d68-0601-0010-13b5-b062adbb3e33
2.
You can determine the upper limit of the time. To do this, you specify a time period relative to the current date. The time unit for the time period can be specified in days, weeks, months, quarters, years, posting periods, or fiscal years.
The upper limit can also be rounded down to the end of a time period by selecting another, additional time unit, so that, for example, only complete months or years can be archived when a date field is selected as a selection characteristic for the time slice. The time slice defined in this way contains the complete time period before the upper limit calculated.
1. If delta field is Date (Record Create Date or change date), then use Upper Limit of 1 day.
This will load Delta in BW as of yesterday. Leave Lower limit blank.
2. If delta field is Time Stamp, then use Upper Limit of equal to 1800 Seconds (30 minutes).
This will load Delta in BW as of 30 minutes old. Leave Lower limit blank.
3. If delta field is a Numeric Pointer i.e. generated record # like in GLPCA table, then use
Lower Limit. Use count 10-100. Leave upper limit blank. If value 10 is used then last 10
records will be loaded again. If a record is created when load was running, those records
may get lost. To prevent this situation, lower limit can be used to backup the starting
sequence number. This may result in some records being processed more than once;
therefore, be sure this DataSources is only feeding an ODS Object
Hope this will help you
Thanks & Regards
Kiran -
UPPER and lower case file extensions for Photo Shop Elements using Windows 7
How do I persuade WIndows 7 to show both UPPER and lower case file extensions, which is a very useful facility offered by my ancient, 2002, version of Photoshop Elements? When processing large volumes (100 plus) photos it is very useful to be able to spot those that have been processed among those awaiting my gentle touch. The JPEG file extension produced by my camera is UPPER case so by using "Save as" with lower case the modified photos are immediately spotted. This worked fine on Windows XP and the same programme has loaded and works well on my new laptop which came loaded with Windows 7 EXCEPT that it persists in using UPPER case all the time, irrespective of the preference settings in PSE. HELP!
Camperman1In PSE there is a facility "File > process multiple files".
Using this facility you can actually process multiple files at one go and you can easily rename images.
Addi -
Generic Data Extraction : Setting of Upper and Lower Limits
Hi all,
I'm doing the delta extraction for this non-standard infocube which stores data about measuring documents. The strategy I used was to first update a ODS with the new/changed measuring documents determined by their last changed date. Then it will update the infocube with the new values. In order to get the delta measuring documents to go into the ODS, I specify a upper limit of 1 and lower limit of 0 in the extractor's generic delta settings to get measuring documents that are created/changed the previous day. But the system will still take in the full set of measuring document.
Is there something that I have missed out?
ThanksHi,
I dont see anything wrong with what you have done. That is correct, it is recommended that the upper safety interval should be set to 1.
But according to you, the system still gets the newly changed records as of current day. Have you checked the update mode? It should be <b>DELTA UPDATE</b>. It might be marked as <b>FULL UPDATE</b>.
Have you successfully initialized the <b>DELTA Update</b>?
Are you using an appropriate DELTA field? It should be a Calendar Day.
Hope I did help and if i did, please grant points...
--Jkyle -
My SD video keeps jumping between the upper and lower frames. So the video starts frame blending and blurring in and out. The sequence settings are set to
Editing Mode: DV NTSC 29.97 frames/second.
Pixel Aspect Ration: D1/DV NTSC (0.9091)
Fileds: Lower Field First
Display Format: 30fps Non-Drop-Frame Timecode
720 x480What is the source of your video, and exactly what is inside your video?
Report back with the codec details of your file, use the programs below... A screen shot works well to SHOW people what you are doing
http://forums.adobe.com/thread/592070?tstart=30 for screen shot instructions
Free programs to get file information for PC/Mac http://mediaarea.net/en/MediaInfo/Download -
How to set upper and lower limit for service notification in SPRO
Hello everyone,
Good morning....!!
I am new to SAP PM and to SCN as well.
I have a question on Service notification user status.
I have notification profile configured in SAP as below:
Status no Status Short text Lower limit Upper limit
5 REGD Registered 1 70
10 PCKS Pack sent 1 70
20 APRC Application received 1 70
etc..
I want the statusesto be set as navigation should only allow to go back one by one...like from APRC -->PCKS not to REGD.From PCKS -->REGD etc..not vice versa.
Can enayone explain me to how to set lower and upper limits for these according ot the above requirement.
for more details please check my attachment.
Thanks in advance..!!
Regards,
Sudha.Once you change the status to previous status, just save the order. Then again open the order & try to change the user status.
Just I made replica of your profile. I could able to change (even without saving the order). -
Datatable for upper and lower limit maintained in Measuring Point.
Hi,
I am making use of user exit : IMCR0001. User exit generates maintenance order for measuring reading which are beyong the range maintained in measruing point.
I have create measuring point with characteristics as TEMPERATURE. I have maintained upper limit : 1500 C & lower limit : 1200 C.
When I check datatable IMPTT and look for upper and lower limit, it is showing me : Upper range :1.7731500000000001E03 Lower range : 1.4731500000000001E03
Why is that I can not find the actual value as 1500 and 1200 n the datatable?
In which datatable I can find these values?
Kindly help.
Thanks in advance.
Regards,
TOM.Hi Tom,
These are system Generated Values, but they will be concatenated by a few Zeros, but you can always find the exact value,
I am able to see the Values correctly in my system follower by some 10-12 zero's "E"+ 02 or 03.
but can check the values
can cross check the Characteristics for the same measuring point?
Regards,
Yawar Khan -
Hi,
Anyone know how to find the upper and the lower threshold of an image? Please help me!
Thanks,
ElinDo you mean the minimum and maximum pixel values? If so, there are subVIs that will read images and returns (among other things) a 2D array of pixel values. Look in the pictures subdirectory inside vi.lib.
Mike...
Certified Professional Instructor
Certified LabVIEW Architect
LabVIEW Champion
"... after all, He's not a tame lion..."
Be thinking ahead and mark your dance card for NI Week 2015 now: TS 6139 - Object Oriented First Steps -
Read the signal value that pass over the upper and lower limit..
how to create the system which can read the signal value that pass the lower and upper limit? i've try but the system only read the value that in range of upper and lower limit..thanks..
Im not very sure if this system can read the value that pass over the limit..because at the save file data so many value(i will attach that file)..and i dont know how to setting to get the failure values only..
Actually i want to build some system that can read and save value that pass over the limit..i take the signal from simulation sine signal..no hardware required..
im very new with this software and im in learning process..
A very big thanks to all that helping me..
save file data from the system
Channels 8
Samples 1 1 1 1 1 1 1 1
Date 2012/03/05 2012/03/05 2012/03/05 2012/03/05 2012/03/05 2012/03/05 2012/03/05 2012/03/05
Time 12:30:11.099999 12:30:11.216 12:30:11.216 12:30:11.216 12:30:11.099999 12:30:11.216 12:30:11.216 12:30:11.216
X_Dimension Time Time Time Time Time Time Time Time
X0 1.0000000000000001E-1 1.0000000000000001E-1 1.0000000000000001E-1 1.0000000000000001E-1 1.0000000000000001E-1 1.0000000000000001E-1 1.0000000000000001E-1 1.0000000000000001E-1
Delta_X 0.001000 0.001000 0.001000 0.001000 0.001000 0.001000 0.001000 0.001000
***End_of_Header***
X_Value Sine (Negative Peak) Failures (Negative Peak) Upper Limit (Negative Peak) Lower Limit (Negative Peak) Sine (Positive Peak) Failures (Positive Peak) Upper Limit (Positive Peak) Lower Limit (Positive Peak) Comment
0.100000 -6.999066 -6.999066 5.000000 -5.000000 6.999136 6.999136 5.000000 -5.000000
0.200000 -6.998993 -6.998993 5.000000 -5.000000 6.999204 6.999204 5.000000 -5.000000
0.300000 -6.998917 -6.998917 5.000000 -5.000000 6.999269 6.999269 5.000000 -5.000000
0.400000 -6.998838 -6.998838 5.000000 -5.000000 6.999331 6.999331 5.000000 -5.000000
0.500000 -6.998756 -6.998756 5.000000 -5.000000 6.999391 6.999391 5.000000 -5.000000
0.600000 -6.998672 -6.998672 5.000000 -5.000000 6.999447 6.999447 5.000000 -5.000000
0.700000 -6.998585 -6.998585 5.000000 -5.000000 6.999501 6.999501 5.000000 -5.000000
0.800000 -6.998495 -6.998495 5.000000 -5.000000 6.999552 6.999552 5.000000 -5.000000
0.900000 -6.998403 -6.998403 5.000000 -5.000000 6.999601 6.999601 5.000000 -5.000000
1.000000 -6.998307 -6.998307 5.000000 -5.000000 6.999646 6.999646 5.000000 -5.000000
1.100000 -6.998209 -6.998209 5.000000 -5.000000 6.999689 6.999689 5.000000 -5.000000
1.200000 -6.998108 -6.998108 5.000000 -5.000000 6.999729 6.999729 5.000000 -5.000000
1.300000 -6.998005 -6.998005 5.000000 -5.000000 6.999766 6.999766 5.000000 -5.000000
1.400000 -6.997898 -6.997898 5.000000 -5.000000 6.999801 6.999801 5.000000 -5.000000
1.500000 -6.997789 -6.997789 5.000000 -5.000000 6.999833 6.999833 5.000000 -5.000000
1.600000 -6.997677 -6.997677 5.000000 -5.000000 6.999862 6.999862 5.000000 -5.000000
1.700000 -6.997563 -6.997563 5.000000 -5.000000 6.999888 6.999888 5.000000 -5.000000
1.800000 -6.997445 -6.997445 5.000000 -5.000000 6.999912 6.999912 5.000000 -5.000000
1.900000 -6.997325 -6.997325 5.000000 -5.000000 6.999932 6.999932 5.000000 -5.000000
2.000000 -6.997202 -6.997202 5.000000 -5.000000 6.999950 6.999950 5.000000 -5.000000
2.100000 -6.997076 -6.997076 5.000000 -5.000000 6.999965 6.999965 5.000000 -5.000000
2.200000 -6.996948 -6.996948 5.000000 -5.000000 6.999978 6.999978 5.000000 -5.000000
2.300000 -6.996817 -6.996817 5.000000 -5.000000 6.999988 6.999988 5.000000 -5.000000
2.400000 -6.996683 -6.996683 5.000000 -5.000000 6.999994 6.999994 5.000000 -5.000000
2.500000 -6.996546 -6.996546 5.000000 -5.000000 6.999999 6.999999 5.000000 -5.000000
2.600000 -6.996546 -6.996546 5.000000 -5.000000 7.000000 7.000000 5.000000 -5.000000
2.700000 -6.996683 -6.996683 5.000000 -5.000000 6.999994 6.999994 5.000000 -5.000000
2.800000 -6.996817 -6.996817 5.000000 -5.000000 6.999988 6.999988 5.000000 -5.000000
2.900000 -6.996948 -6.996948 5.000000 -5.000000 6.999978 6.999978 5.000000 -5.000000
3.000000 -6.997076 -6.997076 5.000000 -5.000000 6.999965 6.999965 5.000000 -5.000000
3.100000 -6.997202 -6.997202 5.000000 -5.000000 6.999950 6.999950 5.000000 -5.000000
3.200000 -6.997325 -6.997325 5.000000 -5.000000 6.999932 6.999932 5.000000 -5.000000
3.300000 -6.997445 -6.997445 5.000000 -5.000000 6.999912 6.999912 5.000000 -5.000000
3.400000 -6.997563 -6.997563 5.000000 -5.000000 6.999888 6.999888 5.000000 -5.000000
3.500000 -6.997677 -6.997677 5.000000 -5.000000 6.999862 6.999862 5.000000 -5.000000
3.600000 -6.997789 -6.997789 5.000000 -5.000000 6.999833 6.999833 5.000000 -5.000000
3.700000 -6.997898 -6.997898 5.000000 -5.000000 6.999801 6.999801 5.000000 -5.000000
3.800000 -6.998005 -6.998005 5.000000 -5.000000 6.999766 6.999766 5.000000 -5.000000
3.900000 -6.998108 -6.998108 5.000000 -5.000000 6.999729 6.999729 5.000000 -5.000000
4.000000 -6.998209 -6.998209 5.000000 -5.000000 6.999689 6.999689 5.000000 -5.000000
4.100000 -6.998307 -6.998307 5.000000 -5.000000 6.999646 6.999646 5.000000 -5.000000
4.200000 -6.998403 -6.998403 5.000000 -5.000000 6.999601 6.999601 5.000000 -5.000000
4.300000 -6.998495 -6.998495 5.000000 -5.000000 6.999552 6.999552 5.000000 -5.000000
4.400000 -6.998585 -6.998585 5.000000 -5.000000 6.999501 6.999501 5.000000 -5.000000
4.500000 -6.998672 -6.998672 5.000000 -5.000000 6.999447 6.999447 5.000000 -5.000000
4.600000 -6.998756 -6.998756 5.000000 -5.000000 6.999391 6.999391 5.000000 -5.000000
4.700000 -6.998838 -6.998838 5.000000 -5.000000 6.999331 6.999331 5.000000 -5.000000
4.800000 -6.998917 -6.998917 5.000000 -5.000000 6.999269 6.999269 5.000000 -5.000000
4.900000 -6.998993 -6.998993 5.000000 -5.000000 6.999204 6.999204 5.000000 -5.000000
5.000000 -6.999066 -6.999066 5.000000 -5.000000 6.999136 6.999136 5.000000 -5.000000
5.100000 -6.999136 -6.999136 5.000000 -5.000000 6.999066 6.999066 5.000000 -5.000000
5.200000 -6.999204 -6.999204 5.000000 -5.000000 6.998993 6.998993 5.000000 -5.000000
5.300000 -6.999269 -6.999269 5.000000 -5.000000 6.998917 6.998917 5.000000 -5.000000
5.400000 -6.999331 -6.999331 5.000000 -5.000000 6.998838 6.998838 5.000000 -5.000000
5.500000 -6.999391 -6.999391 5.000000 -5.000000 6.998756 6.998756 5.000000 -5.000000
5.600000 -6.999447 -6.999447 5.000000 -5.000000 6.998672 6.998672 5.000000 -5.000000
5.700000 -6.999501 -6.999501 5.000000 -5.000000 6.998585 6.998585 5.000000 -5.000000
5.800000 -6.999552 -6.999552 5.000000 -5.000000 6.998495 6.998495 5.000000 -5.000000
5.900000 -6.999601 -6.999601 5.000000 -5.000000 6.998403 6.998403 5.000000 -5.000000
6.000000 -6.999646 -6.999646 5.000000 -5.000000 6.998307 6.998307 5.000000 -5.000000
6.100000 -6.999689 -6.999689 5.000000 -5.000000 6.998209 6.998209 5.000000 -5.000000
6.200000 -6.999729 -6.999729 5.000000 -5.000000 6.998108 6.998108 5.000000 -5.000000
6.300000 -6.999766 -6.999766 5.000000 -5.000000 6.998005 6.998005 5.000000 -5.000000
6.400000 -6.999801 -6.999801 5.000000 -5.000000 6.997898 6.997898 5.000000 -5.000000
6.500000 -6.999833 -6.999833 5.000000 -5.000000 6.997789 6.997789 5.000000 -5.000000
6.600000 -6.999862 -6.999862 5.000000 -5.000000 6.997677 6.997677 5.000000 -5.000000
6.700000 -6.999888 -6.999888 5.000000 -5.000000 6.997563 6.997563 5.000000 -5.000000
6.800000 -6.999912 -6.999912 5.000000 -5.000000 6.997445 6.997445 5.000000 -5.000000
6.900000 -6.999932 -6.999932 5.000000 -5.000000 6.997325 6.997325 5.000000 -5.000000
7.000000 -6.999950 -6.999950 5.000000 -5.000000 6.997202 6.997202 5.000000 -5.000000
7.100000 -6.999965 -6.999965 5.000000 -5.000000 6.997076 6.997076 5.000000 -5.000000
7.200000 -6.999978 -6.999978 5.000000 -5.000000 6.996948 6.996948 5.000000 -5.000000
7.300000 -6.999988 -6.999988 5.000000 -5.000000 6.996817 6.996817 5.000000 -5.000000
7.400000 -6.999994 -6.999994 5.000000 -5.000000 6.996683 6.996683 5.000000 -5.000000
7.500000 -6.999999 -6.999999 5.000000 -5.000000 6.996546 6.996546 5.000000 -5.000000
7.600000 -7.000000 -7.000000 5.000000 -5.000000 6.996546 6.996546 5.000000 -5.000000
7.700000 -6.999994 -6.999994 5.000000 -5.000000 6.996683 6.996683 5.000000 -5.000000
7.800000 -6.999988 -6.999988 5.000000 -5.000000 6.996817 6.996817 5.000000 -5.000000
7.900000 -6.999978 -6.999978 5.000000 -5.000000 6.996948 6.996948 5.000000 -5.000000
8.000000 -6.999965 -6.999965 5.000000 -5.000000 6.997076 6.997076 5.000000 -5.000000
8.100000 -6.999950 -6.999950 5.000000 -5.000000 6.997202 6.997202 5.000000 -5.000000 -
MIC with different upper and lower limit
Hi experts,
I have a scenario where I have a characteristic to be tested for trace element in a chemical.
But the upper and lower specification of this MIC is different for different chemicals (material numbers) . ie the specification depends on chemical (material) to be inspected.
So I am stuck with a combination a number of MICs with same trace element (say iron) to be tested for a number of chemicals.
How does QM handle this scenario ?
Rgds
JMG1st - Are you batch managed? if so you can create a batch class and add a general characteristic to it linked to a single MIC. Use this MIC in your inspection plans. Then in the batch class set the specs limits.
You can create a separate batch class for each group of materials. I.e. those with the same specs.
You can also modify the spec value in the classification view for each material that is different then the spec in the class.
You can also create plans which use the same MIC but in the plan you unlock it and set the spec. Then assign all the materials using that spec to the same plan.
This is all very simplied above. But under NO circumstances should it be necessary to create multiple MICS for the same test with all different specs!
Craig -
How do I remove the background display in the upper and lower parts of the page?
The upper and lower ends have a background display when a new version was updated.I wish to remove the display.
== This happened ==
Every time Firefox opened
== TodaySounds that you installed a Persona.
You can uninstall that Persona and revert to the ''Default'' theme (Tools > Add-ons > Themes).
See [[Using themes with Firefox]] and http://kb.mozillazine.org/Themes (Lightweight theme) -
Is Central Search Searchable Via Upper and Lower Case Letters
Good evening,
Does anyone know if Central Search is searchable using both upper and lower case letters? We have the functionality enabled and can only bring back search results when we use upper case letters. When we search on the same marketing object using lower case letters, we do not get any results. For example, TK2292 brings back marketing object TK0002292 but tk2292 does not bring back any results. Advanced Search appears to be able to handle both search scenarios. Any guidance would be greatly appreciated.
Regards,
GreggHello,
Did you put a breakpoint in the query method to check what you receive in the field 'marketing object' when you start from the central search of the advanced search?
Is it different?
Regards,
Fred -
Lower limit relative and upper limit dropdown in timesheet
Iu2019ve a question about the time sheet.
In the back end side we set the configuration to scroll down or up the time sheet. Setting Lower limit relative and upper limit relative with Value "2" .Now users can scroll down/up two weeks the timesheet from the key date
Iu2019ve checked In CAT2 tcode and it works fine. If you go back for more than 2 weeks the system returns an error.
But when i go to portal timehseet ,this error is not happening ,not retricting the user.
Allowing the user to move backwards.
How this can be restricted in portal time sheet in ess.
Thanks,
NachyIt should be noted that this exit only prevents changes not display
There was moves to release functionality to limit scrolling on Webdynpro - however you would need to open a development request as per www.service.sap.com/rollin to find out what progress has been made
I also saw one customer who inserted a line of custom code to restrict scrolling access -4 weeks
and +6 weeks via sy-datum + 42 and sy-datum - 28 - however a complete solution would require an HR/CATS ABAP'er
Cheers
Stuart
Maybe you are looking for
-
Hello, I just activated a new iPhone 5 from Rogers. I am only getting 1 day, 13 hours on standby with 7 hours, 11 mins of usage with LTE, GPS, and push notifications set on(Facebook, and Email). Just wondering if this is normal for the iPhone 5.
-
How do you get rid of 'empty' pre-roll time in logic pro 9?
how do you get rid of the pre-roll time in logic pro 9? My project's start time is 8-bars before any material, or tempos, or anything... Can't move the start time back to ")" (zero) STUCK!! at -8 The song now has 20 seconds of dead air time i
-
Upload a file into Oracle database without using a temp file in the server.
Hello. I need to upload a file into a Oracle database, but I have not permission to write a temp file in the aplication server. Because of this, I can't use a MultipartRequest object. Does anybody know how to do this? Thanks everybody for your help.
-
How can Access mysql data using JavaScript
Hi Friends, Could u please tell how can i access data from mysql using Java Script.. please help me on this .. thanks
-
My screen Documents are locked in place, help unlocking please.
All of my screen documents and pictures have locked themselves in place and wont allow me to move them. Can anyone help me figure out how the get them to move again.