Initial Match Code Error

All,
We're deploying DQM 12.1.3 for our new CRM 7 installation.  So far everything has installed and been configured without issues.  However, when trying to run the Initial Match Code setup program (/FLDQ/RSADRINI), it fails within a few seconds of running it with the error message:  "Error executing RFC call      GET_MATCH_CODES"  it the continues with:  "Report execution ened with errors.  No updates done to match codes table."
This issue is hapenning in our QA envrionement, this process successfully completed in DEV.  A major difference between the two systems is that there is almost no customer data in CRM-DEV.  In CRM-QA however, we loaded all the customers from our ECC system.
Can anyone shed some like on the matter?  This is our first attempt in deploying DQM.
Thanks in advance,
Jose

Hi Jose,
Are you still having the problem as described?  If so, I would suggest checking that a Batch RFC Server is attached to your SAP application's gateway.  If you use the transaction SMGW > Logged on Clients, you should see at least two (2) entries related to DQM for SAP Solutions:
FLRFCSRV (transactional rfc server, could be more of these)
FLRFCBTC (This one is your batch server; only one allowed in 12.1.3 release).
I believe that the RSADINI uses the batch RFC server.
If you have no registered batch RFC Servers on the SAP gateway, then my initial guesses:
1) It isn't started; start it.  When it states that initialization is complete, check in about 10 minutes SMGW for its presence.
2) It has crashed (more difficult with the 12.1.3 release, but, can happen) > try to restart > fix any errors if present.
If this error continues and the Batch RFC Server is running correctly, then you may have to start looking further down the stack.  RFC Server logs or Data Services Management Console Realtime_Batch_Name_And_Address_Match (I think that is the name).
Not playing support here.  Just happen to see this post and thought I would drop off my two cents on the way by.
David
Edited by: David Sandy on Jan 29, 2011 12:13 AM

Similar Messages

  • Match Code Error

    Hi All,
    I am trying to add the Company Code to the Search Help function in FB50/60/70.
    So in SE11, for the Search Help: PRPM, and the included search help tab, where I see all the tabs visible on the FB50 transaction, I tried to add the field: PBUKR and Data Element: PS_PBUKR, but I keep getting the below error:
    Search help parameter PBUKR does not occur in the selection method.
    How can I correct this? Any suggestions..?
    Thanks much
    RS

    Uhmm....
    so the correct name of the search help is PRPMP, not PRMP, isn't it?
    If it's so Rob is right, you need to add the field PBUKR in the view V_PRPMP and so it'll be available for the search help automatically.
    The problem is it needs to get the Access Key to update the standard view (it doesn't need it for the search help).
    Max

  • How can I correct this error: no matching code signing identity found

    I signed up as an apple developer so I could download the tools to learn to build apps. I just installed Xcode 5.1.1, when i opened the program and created my first test project I got an error message: "no matching code signing identity found". how can i get rid of (correct) this error? I am just learning and I am not ready to join the $99 developer program yet.

    Try setting Signing to None in the Target General pane.

  • No matching code signing identity found - Xcode error

    Hello,
    I am new to Mac and Xcode. I just want to learn Xcode and not publish any apps. Hence I did not enroll in the paid developer program.
    Whenever I try to create a project in Xcode, it gives me this error - "No matching code signing identity found". If I click on "Fix Issue", it asks me to add my apple ID. I did that but I cannot add it to any team. I also tried requesting a certificate through keychain. But I am not sure on how to check the status of that.
    Please pardon my lack of knowledge on this as I just a beginner. But any help on this will be greatly appreciated.
    Thank you.

    You will probably get better answers to questions like these in the developer forums. https://developer.apple.com/devforums/
    Best of luck.

  • MATCH COD OBJECTS

    Hi All
    While creating Match Code Objects
    i am getting a syntax error like elementary search help has no selection method
    how to solve this
    even i could not able to store in my package
    Message was edited by:
            geetha

    hIGeetha,
    Follow these steps for creating match code.
    now go to SE11 click on search help button and create.
    click on elementary search help
    once you have created you will see selection method there give there your table name (lfa1)
    in the paremeters give the field name <field name> and click on EXP button Lpos as 1 & Spos as 1 then enter and save.
    In the code give this way
    select-options: S_<fieldname> for lfa1-<fieldname> MATCHCODE OBJECT MCO..
    ACTIVATE AND EXECUATE WHEN U CLICK ON F4 you can see the values.
    Thanks
    Vikranth Khimavath

  • Manual Bank Statement(Match Code)

    Hi All,
    I am creating a manual bank statement . When i go to specifications and give my variant and match code for customers D and match code for vendors K and processing type 4. It is showing an error match code ID DEBI D does not exist. Please any body answer my question ASAP.
    Regards,
    Vikas.

    hi,
    As per my idea i dont think so the standard sap provides such facility.

  • The code error which is difficult to understand?

    HI,
    I am getting the following code error which is in red color. How to solve the problem? The errors are in Line 1, 2, 5 & 6. This code is used for auto typing style.
    if (Number(TextLen)<=Number(length(TextBuffer)) and Number(TextLen)<>0) {
       TextLen = Number(eval("TextLen"))+1;
        TypeField = substring(TextBuffer, 1, TextLen);
    } else {
       TextLen = 0;
    1084: Syntax error: expecting rightparen before and.
    1084: Syntax error: expecting rightbrace before semicolon.
    1084: Syntax error: expecting rightbrace before semicolon.
    1100: Syntax error: XML does not have matching begin and end tags.

    kglad wrote:
    try:
    if (Number(TextLen)<=Number(TextBuffer.length) && Number(TextLen)<>0) {
       TextLen = Number(eval("TextLen"))+1;
        TypeField = substring(TextBuffer, 1, TextLen);
    } else {
       TextLen = 0;
    Thanks for the quick reply. Now getting two errors and both are in line one which is in RED color:
    1084: Syntax error: expecting identifier before greaterthan.
    1084: Syntax error: expecting rightparen before leftbrace.
    if (Number(TextLen)<=Number(TextBuffer.length) && Number(TextLen)<>0) {

  • Capture/time code errors

    Hello all -
    Every now and then while capturing video I come across this issue of capturing stopping and getting the error message "Final Cut Pro has detected a time code error...etc"
    What's puzzling is that it is from a tape that was a solid hour of video (rather than starting and stopping of recording) I assume I just ran into a bad tape.
    I don't see any digital break up - or crease in the tape or anything like that - just a slight hitch in the audio -- then the stopping of capturing.
    MY QUESTION - are there any settings that I could change for this capture that would "allow" the capturing? (lowering the threshold of what FCP will capture)?
    or should I dub the tape to a new tape and (hopefully) get clean time code on the new tape?
    Thanks.

    This can happen for a number of reasons:
    1. Dirty heads on the recording and/or playback device.
    2. Mis-matching heads between the recording and playback devices
    3. Wrong firewire control protocol.
    4. Using the system hard drive as the capture scratch drive
    5. A faulty firewire cable or the cable is loose at either the computer or camera connection
    6. A faulty firewire port
    7. A software glitch
    There probably are others as well.
    x

  • Plant a match code for opening a project

    Hi All,
    I am trying to develope a match code of Plant for opening a project. Such that a list of projects to come out after entering a plant then select a project and then open a project like PO by supplying plant. I have gone through SPRO that is OPT2 match codes for Project definitions. But not found ready made match code to be included.
    Is ther any easy way other ABAP use? or give logic how to deveope it.
    Thanks and regards

    Hi
    If you mean opening a project in standard reports like CN41, it would be easier to use "dynamic selection option" and hard code the plant, and then save the selection version.
    Everytime, you want to open projects in the respective plant, you can call the selection version in the initial screen of the report.
    Hope it helps.
    Regards
    Srikrishna

  • Traport importing problem with repeating return code error 8

    Hi all,
    We are facing some transport import problem.When we sent transport initially AAA900244,they faced with return code error 8 and syntax error 109.As the information provided by the client,one of the include  program which is not availble at client system that was included in this transport.So that was the problem.Again we have taken  new  tranport AAA900247 without this include program then same type of error message they faced with return code error 8 and syntax error 109 in the include program when imported.
    I have one doubt, when importing new transport this should overwrite the earlier transport data.Why the same type error client is getting.What might be the reason.
    Is earlier transport  imported?? Why it throwing same type error.What actually the fuctionality of Return code 8 whether it is imported or discarded.
    Thanks in advance.
    Regards.....Balu

    Hi Ramesh,
    That include is not at all required at client system.So next time when we have taken transport we have not included this include program.They imported new transport without this include program.But they are facing same error as they faced first time. What could be reason??
    Regards...Balu

  • FBL5N : problem with Match-code

    Hi,
    In Tcode FBL5N i click on match-code of Customer Account's field to choose a Customer, in the first table (Customers by company code) when Ii click on one customer the list of customers is closed but i get nothing in Customer Account's field (it is empty)
    Please how to resolve this problem ?
    Regards.
    Edited by: jehade el aoumari on Jan 20, 2010 9:28 AM

    Hi ,
    I had the same issue with FBL1N and I managed to solve it.
    1. Open SE11
    2. Select radio button search Help
    3. Enter DEBI
    4. Click on change
    5. Choose Maint. in logon lang.
    6. Go to tab Included search help
    7. Select line DEBID
    8. Click on Param. assignment
    9. On the 1st line enter      KUNNR     C      KUNNR
    10. On the 2nd line enter   BUKRS     C      BUKRS
    11. Save
    This should solve your issue.
    Regards,
    Ben

  • How to add the Match code object for the requisitioner field in TCODE ME51N

    Hi,
    How to add the search help (Match code object) for the requisitioner field in transaction ME51N.
    Please  do the needful to me.
    Regards
    Rajesh

    don't you think that posting your question to a microsoft developer site would be more efficient?
    regards,
    anton

  • Match code in report selection screen does not show any values for 0FISCPER

    Hi Experts,
    I have problem with selection screen in several reports. When I use match code for fiscal period selection I get only # as a possible value. I have checked the master data they seem to be correct. I work with 7.0 BW system. Can you please give me any hint what I should check?
    Thank you,
    Michal

    Hi,
    maybe I ask different way - how do you add characteristic values for a characteristic in the BEx? Is it automated somehow in SAP (e.g. from master data)? For the fiscal period I use custommer exit to fill in the default value, which is the current fiscal period. But this is something different, right?
    <removed by moderator>
    Michal
    Edited by: Arun Varadarajan on Nov 14, 2008 3:55 PM

  • Invalid Key code Error while installing crystal report server 11

    While installing crystal report server 11,i am facing an erro which says Invalid Key code Error.I had raised this issue to SAP customer support and attaching the conversation that we had.PLEASE HELP me to resolve the issue.
    MAILS--Dear Mohit,
    Thanks for the patience.
    We have received the below update from the Licensing Team.
    You received your permanent key in respect of these licenses - the key is  for Crystal Reports Server XI.
    You did not purchase these licenses for Crystal Reports Server, but purchased it for Crystal Reports and a 5-named user license for Crystal Reports was included as a special offer.  The software included was version XIR2, but you elected to use version XI instead and received key .
    You would need to enroll the licenses in maintenance if you want to upgrade them.
    In case of any queries please create a ticket via the Service Market Place.
    Regards,
    Jessy
    Customer Interaction Center
    SAP Active Global Support
    Hello Jessy,
    The customer received their permanent key in respect of these licenses - the key is  for Crystal Reports Server XI.
    They did not purchase these licenses for Crystal Reports Server, they purchased Crystal Reports and a 5-named user license for Crystal Reports was included as a special offer.  The software included was version XIR2, but they elected to use version XI instead and they received key .
    They cannot decide to upgrade now - they must enrol these licenses in maintenance if they want to upgrade them.
    Kind regards,
    Rosemary
    From: BOSAPASIA
    Sent: 29 September 2009 05:49
    To: Savage, Rosemary
    Subject: FW: Crystal Reports Server Installation Issue
    Importance: High
    HI Rose ,
    Need your assistance on the below issue.
    Customer purchased Crystal Report Server XI R2 in 2005. When he is trying to install it now, he is getting an Invalid Key code Error.
    He has provided us the Scanned copies of the Key code and the registration number.Can you please help and check if he can be provided with a Keycode.
    Regards,
    Jessy
    CIC Team Lead
    Customer Interaction Center
    Global Support Centre India
    SAP Labs India Pvt Ltd
    Hi,
    Providing you with the required details to proceed further
    Registration Number-
    Registration Email Address-taxmantra.support
    And also please find attached the scanned copy of the Registration key we got for the Crystal report server.
    Dear Mohitk,
    Thank you for your information.
    I checked with the concerned colleague and received the below update:
    Please check from where you got this key code. If from a paper, please scan it to us. Please let them track to the original paper or email.
    If you have registered the key code, please provide us the registration number or registration email address so that we will try to check for you.
    If you did not register before, as the promotion is over so the key code could not be replaced.
    I request you to kindly check the same at your end and revert with the details.
    Moreover, there are two ways for Crystal Report customer to get support.
    One is customer with bundled product such like BOE and under maintenance. These customers will have an S-user ID and password to log a case in service market place via http://service.sap.com/message
    A learning map was provided, listed on left column.
    The other is customer with only Crystal report product, the support is via SDN.
    http://service.sap.com =>Crystal Reports and Xcelsius Support=>Crystal Reports and Xcelsius Forums
    Customers can first check whether other customer has got the same issue and find the reply from our engineers.
    You may also post your own thread for support.
    Anything else I could help, please do not hesitate to contact again.
    Hi,
    I am providing you with the details required to resolve the issue related to Crystal report installation,for reference of the issue please refer the mail below.
    Please find attached the Scanned Document  containing the details as per the details required by you.
    Hope to see a quick resolution for the issue.
    Dear Mohit,
    Thank you for your e-mail.
    As discussed, I understand that youu2019ve procured Crystal Reports Server 11 in 2006. However youu2019re facing issues with key codes while reinstalling the same. We request you to kindly provide us with below details for further assistance.
    Your customer number:
    Your customer name and address:
    Purchase order number:
    Any other products purchased along with Crystal Reports Server 11
    Any S-User Id:
    Any old case ID:
    Please feel free to contact us if any further queries.
    Hi,
    I am raising this concern on behalf on Taxmantra project (Tata Consultancy Services noida).
    We have bought licensed Crystal Reports Server 11 near by 2006.We are trying to install the crystal server but while installing ,we have encountered with an error message that:-
    "The product key code you have entered is incorrect"
    We are facing the same issue in 2006,I am attaching with this email the conversations that was held in 2006 to get the correct key code.
    Please help us to resolve the issue as early as possible.
    My contact number:
    If you need any further information do let me know

    Ajit,
      By design, the product is not able to be installed under the superuser account.
    1.  Create a new user and specify a home directory for the user without a quota set.
    2.  Copy or move the installation files to a directory that the new user can read.  I suggest you move the installation files directly into the new user's home directory.
    3.  Logon as the new user (or su - newuser)
    4.  run the installation shell script using that new user's account.
    NOTE:  Ensure the system meets the requirements from the supported platforms documents.
    .Tony

  • Part of Photoshop isn't functioning.  Under adjustments, when HDR toning is clicked on I get a code:  Error 48: File or folder does not exist.  Line:11  - $.evalFile(g_StackScriptFolderPath   "StackSupport.jsx");  How can it be fixed?

    The phone company was here working on something while I was gone.  They sat down at my computer (iMac) and since then HDR toning doesn't work.  Get the code:   Error 48: File or folder does not exist.    Line: 11     ->  $.evalFile(g_StacScriptFolderPatch + "StackSupport.jsx");   How can this be fixed?   

    Go to //Applications/Adobe Photoshop [Version]/Presets/ Scripts/Stack Scripts Only/ and see if StackSupport.jsx is there. If it is not, uninstall and reinstall Photoshop to have it added back in. If it is there, first try recreating the Photoshop Preferences (hold down Command+Option+Shift while launching Photoshop).

Maybe you are looking for