Inspection Points for Inprocess Inspection

Hi all,
My client is doing In process Inspection during Production process.
They are inspecting based on the Inspection Points (Shift wise).
If I add Inspection point referrence at Header level in routing, after adding the MICs in the required operation, while saving it gives an error message stating that "Maintain Inspection Point referrence at Operation level".
Task List contains error. You want to save or cancel.
How can I achieve this with out error.
Thnx in advance
Sam

Hi Sam,
Go to Routing and select the operation, and double click the operation. Then system will popup the new screen here under Quality management Inspection point tab choose No relation. and save the routing.
Check and give the feed back.
Regards,
S.Babusingh

Similar Messages

Result Recording for inprocess lot

Hello SAP gurus.
For in process inspection lot i have 3 operation for testing my requirment is if i goning for result recording for second operation without result recording for first operation system should restrict me. we are using 100 inspection point for inprocess inspection please suggest how can we do this?
Regards.

Dear,
Goto OPK4 -Select order type /Plant - Select 'Generally valid setting' for 'Operation sequence-Select 'Error when operation sequnce is not adhered and also QM Error message if no inspection result exists.
Or you can use the exit CONFPP05 PP order conf.: Customer specific enhancements when saving .
Regards,
R.Brahmankar

Inspection plan for inprocess inspection

Hi QM Gurus
please let me know can I use an inspection plan for inprocess inspection
Thanks
TR

Dear,
Inspection Plan is similar to routing, which will indicate what are all characteristics need to be checked / inspected when you receive a material. Is a master data. Once the inspection lot is created we will check the inspection plan and perform the inspection and give the defects recording and usage decision for the inspection lots.
So for inspection type 03 use routing with usage as 1 and status as 4 and control key as PP04 to specify the inspection characteristics.
when u cofirm that perticular operation it will ask to record the results. Inspection lot get genarated during order release this we can see in the order header data assignment tab. PP04 assignement says this operation is relevent for inprocess inspection and we need to assign MIC's for this which are relevent created in QS21 for this also sampling procedure created in QDV1.
Regards,
R.Brahmankar

Is it possible to create inspection plan for "Inprocess Inspection"

Hi,
Is it possible to create inspection plans for "Inprocess Inspection".
If yes , what would be the "task List Usage".Is it "1"?
If no ,then how to map this requirment?
Regards
Vemula

Hi
Vemula
Generally as Per SAP std Routing is used for inspection of 03 type of inspection.
but you can also customize the Inspection task list Usage for Inprocess Inspection.
This is possible through
QCC0>Quality Inspection>Insp lot creation>Assign Insp type to origine>
here informt of 03 inspection type you can assign
Task list type:Q
Usage:either 1(Production) or 3(Universal)
save
Regards
Poonam

Exit For Inprocess Inspection

Hi All,
I have an issue regarding in-process inspection. With the inspection type 03 , when process order is created immediately
inspection lot is created .In this case the system will allow me to carry out conformation after each operation results according.
i need an exit like after confirmation only , i should be able to do results recording.How to achieve this . Please let me know is it possible ti achieve through any User Exit.
Regards,
Madhu.

Dear,
Inspection Plan is similar to routing, which will indicate what are all characteristics need to be checked / inspected when you receive a material. Is a master data. Once the inspection lot is created we will check the inspection plan and perform the inspection and give the defects recording and usage decision for the inspection lots.
So for inspection type 03 use routing with usage as 1 and status as 4 and control key as PP04 to specify the inspection characteristics.
when u cofirm that perticular operation it will ask to record the results. Inspection lot get genarated during order release this we can see in the order header data assignment tab. PP04 assignement says this operation is relevent for inprocess inspection and we need to assign MIC's for this which are relevent created in QS21 for this also sampling procedure created in QDV1.
Regards,
R.Brahmankar

SSRS 2008 Column Chart with Calculated Series (moving average) "formula error - there are not enough data points for the period" error

I have a simple column chart grouping on 1 value on the category axis. For simplicity's sake, we are plotting $ amounts grouping by Month on the category axis. I right click on the data series and choose "Add calculated series...". I choose moving average. I want to move the average over at least 2 periods.
When I run the report, I get the error "Formula error - there are not enough data points for the period". The way the report is, I never have a guaranteed number of categories (there could be one or there could be 5). When there is 2 or more, the chart renders fine, however, when there is only 1 value, instead of suppressing the moving average line, I get that error and the chart shows nothing.
I don't think this is entirely acceptable for our end users. At a minimum, I would think the moving average line would be suppressed instead of hiding the entire chart. Does anyone know of any workarounds or do I have to enter another ms. connect bug/design consideration.
Thank you,
Dan

I was having the same error while trying to plot a moving average across 7 days. The work around I found was rather simple.
If you right click your report in the solution explorer and select "View Code" it will give you the underlying XML of the report. Find the entry for the value of your calculated series and enter a formula to dynamically create your periods.
<ChartFormulaParameter Name="Period">
<Value>=IIf(Count(Fields!Calls.Value) >= 7 ,7, (Count(Fields!Calls.Value)))</Value>
</ChartFormulaParameter>
What I'm doing here is getting the row count of records returned in the chart. If the returned rows are greater than or equal to 7 (The amount of days I want the average) it will set the points to 7. If not, it will set the number to the amount of returned rows. So far this has worked great. I'm probably going to add more code to handle no records returned although in my case that shouldn't happen but, you never know.
A side note:
If you open the calculated series properties in the designer, you will notice the number of periods is set to "0". If you change this it will overwrite your custom formula in the XML.

Change pointer for HR master data is not getting generated in table BDCP

Hi,
I have done all the required configuration for change pointer for HR master Distribution and it was working fine few days back. Now suddnly it has stopped working.
Can anyone assist me on how should i debug it.
Thanks
Sunil Singh

Hi Shital,
Thanks for your Reply.
I am not able to find that path in SPRO
Basic Functions-> application Area
And Also My change pointer configuration was working properly and it suddenly stopped working.
I mean to say all the required settings was done previously.
Anyways kindly let me know how should i proceed.
Thanks
Sunil Singh

I am trying to enter a split point for a file going on a dual layer disc. There are chapter markers in the file but the automtic function doesn't see them. Can I insert a point for the layer split in DVD Studio Pro 3 or 4? It doesn't appear that the autom

I am trying to enter a split point for a file going on a dual layer disc. There are chapter markers in the file but auto function does not see them. Went back and put a small split in the timeline in fcp and exported to mpeg 2 again and auto function does not see that either? Manual msays to manualy enter split poind in DVDSP but can't find any way to enter that split point in DVDSP? How can I manualy enter a split point in DVDSP 3 or 4?
Elizabeth/Roger Cook Films

This is definitely not the behavior I see. When I left click it adds a marker,
When I right click, I see the following
Do you have any OS hacks installed on your computer or have you changed the mouse behavior in system preferences: mouse? If not, I'd suggest you run digital rebellions preference manager and reset your dvdsp preferences.
https://discussions.apple.com/docs/DOC-2491

How to take a single data point for each trigger pulse ( synchronous acquisition).

hi
          im using the pci-mio-16E1 card, with the IDE VC++, so im looking for an example to explicate me how to make an synchronous acquisition data using an external timing, so the idea is to acquire (take) a single data point for each trigger pulse from one input channel ,and saving the data in a file .
now im making a code using the AI_setup and DAQ_op functions, im getting a speed acquisition (it is the start of acquisition data), and it is a synchronous acquisition just for one trigger pulse, and me i looking for an acquisition for each trigger pulse.
so to  understand my problem you can see my code :
iStatus = Timeout_Config(iDevice, lTimeout);
         iRetVal = NIDAQErrorHandler(iStatus, "Timeout_Config", iIgnoreWarning);
   // configuration and selection of signal trigger
         iStatus = Configure_HW_Analog_Trigger(iDevice, ND_ON, iLowValue,iHighValue, ND_ABOVE_HIGH_LEVEL, ND_THE_AI_CHANNEL);
        iRetVal = NIDAQErrorHandler(iStatus, "Configure_HW_Analog_Trigger", iIgnoreWarning);
iStatus = Select_Signal(iDevice, ND_IN_CONVERT, ND_PFI_2,ND_HIGH_TO_LOW);
         iRetVal = NIDAQErrorHandler(iStatus, "Select_Signal", iIgnoreWarning);
    iStatus = AI_Setup(iDevice, iChannel, iGain);
   iRetVal = NIDAQErrorHandler(iStatus, "AI_Setup", iIgnoreWarning);
   while ((iReadingAvail != 1) && (iStatus == 0)) {
/* Wait until reading is available. */
         iStatus = AI_Check(iDevice, &iReadingAvail, &iReading);
        iRetVal = NIDAQYield(iYieldON);
       // Acquire data from a single channel
    iStatus = DAQ_Op (iDevice, iChannel, iGain, piBuffer, ulCount, dSampRate);
   while ((iDAQstopped != 1) && (iStatus == 0)) {
        iStatus = DAQ_Check(iDevice, &iDAQstopped, &ulRetrieved);
        iRetVal = NIDAQYield(iYieldON);
       iStatus = DAQ_VScale(iDevice, iChannel, iGain, dGainAdjust, dOffset,ulCount, piBuffer, pdVoltBuffer);
      iRetVal = NIDAQErrorHandler(iStatus, "DAQ_VScale",iIgnoreWarning);
   /* Set analog trigger mode back to initial state. */
       iStatus = Configure_HW_Analog_Trigger(iDevice, ND_OFF, iLowValue,iHighValue, ND_ABOVE_HIGH_LEVEL, ND_THE_AI_CHANNEL);
/* Set PFI line back to initial state. */
       iStatus = Select_Signal(iDevice, ND_IN_START_TRIGGER,ND_AUTOMATIC, ND_DONT_CARE);
          iStatus = DAQ_Clear(iDevice);
/* Plot acquired data */
      iRetVal = NIDAQPlotWaveform(pdVoltBuffer,ulCount, WFM_DATA_F64);
so this is the data acquired -0.900879,-0.900879,-0.900879,-0.900879,-0.900879,-0.900879,-0.900879,-0.900879 and i think that is a noise because all time i get this data.
tank you very mutch fo your help

Hello,
Please see the responses to this thread at the following post.
http://forums.ni.com/ni/board/message?board.id=250&message.id=13686
Also, please only post one thread per issue.
Regards,
Sean C.

How to determine the mount point for directory /tmp ?

Folks,
Hello. I am installing Oracle 11gR2 RAC using 2 Virtual Machines (rac1 and rac2 whose OS are Oracle Linux 5.6) in VMPlayer and according to the tutorial
http://appsdbaworkshop.blogspot.com/2011/10/11gr2-rac-on-linux-56-using-vmware.html
I am installing Grid infrastructure. I am on step 7 of 10 (verify Grid installation enviroment) and get this error:
"Free Space: Rac2: /tmp"
Cause: Could not determine mount point for location specified.
Action: Ensure location specified is available.
Expected value: n/a
Actual value: n/a
I have checked the free space using the command:
[root@Rac2 /]# df -k /tmp
Output:
Filesystem 1k-blocks used Available Use% Mounted on
/dev/sda1 30470144 7826952 21070432 28% /
As you see above, the free space is enough, but could not determine mount point for /tmp.
Do any folk understand how to determine the mount point for directory /tmp ?
Thanks.

I have just checked "/home/oracle/.bash_profile". But in my computer, there is no "oracle" under /home directory.Is this your first time Linux and Oracle installation? I had a brief look at your referenced link. The reason why you do not find a "oracle" user is because the instructions use "ora11g" instead, which, btw, is not standard. The directories of your installation and your installation source can be somewhat different from known standards and you will have to adjust it to your system.
My best guess is that you have either missed something in the instructions or you need to ask the author of the blog what is wrong. The chance to find someone here who has experience with these custom instructions is probably unlikely.
I suggest you try to locate the cluster verification tool, which should be in the bin directory of your grid installation. Alternatively you might want to check the RAC, ASM & Clusterware Installation forum: RAC, ASM & Clusterware Installation

3X points for LG washer and dryer is false advertisement-- 5 months later I am still waiting

I have tried multiple attempts (at least 3 calls) to Best Buy service and have yet to get my issue resolved. I made anLG purchase of a washer and dryer on Octobe 6th 2014. The add said get 3x points so that made my final decision to purchase from Best Buy. 5 months later I have yet to get my 3X points. This is false advertisement. In all three of my calls the representative has apologized and opens up a case. I never hear anything back. I keep being told I got my 20% incremental points but that is not what I am disputing. The last time the represenatative gave me some points for my frustration but said someone would get back to me and that was back in December. Its frustrating as I really like shoping at Best Buy but am becoming very annoyed and really do not want to purcahse here anymore if Best Buy does not follow through with their advertisements. I do not have a copy of the ad (wish I would of kept one) but Best Buy should be able to verify all their ads. I certainly am not making this up. As a matter of fact, the salesperson at the store looked at the ad and confirmed that I should be getting 3X points for the purchase. Since I have tried multiple attempts on the phone with no success then perhaps this message might work better. I would discourage anyone right now in believing any of there reward ads. My time is worth more than trying to chase Best Buy down for points I am owed and will begin to make my purschases elsewhere. BEWARE customers as I am a very dissatisified customer at the moment.

Hi analydia,
Thank you for taking the time to sign up for the forum and connect with us. I can understand why it is you would feel frustrated, and I 100% agree that you should not have to chase down any points that you may have qualified for. To hear that you have potentially been waiting 5 months for points to post to your My Best Buy account, it is just really disappointing.
It will generally take 20 to 35 days for points to post to a member's account for a Magnolia or Pacific Sales purchase, which will start after any scheduled deliveries are completed. I looked over your account using the email address you registered with the forum and I do see that the base points for your Pacific Sales purchase have already posted. With that being said, it should just be a matter of confirming 3X points was being offered and whether or not your purchase qualified. It appears that your LG washer and dryer may have been eligible for 5X points, but it depends on which models you purchased.
I am very sorry for any inconvenience you have experienced up until now, and I would like to see what I can possibly do to further assist. To gather some additional information and go over your My Best Buy account with you, I will be sending you a private message. You can check your private messages by logging into the forum and clicking on the little yellow envelope located at the top of the page.
I hope you have a wonderful day!
Derek|Social Media Specialist | Best Buy® Corporate
Private Message

24 points for a single answer

Hi SDN team,
i can't stop complaining about getting more than 10 points for a single answer
Please have a look at this Re: Inexisting BAPI_FLIGHT_GETLIST in our SAP system IDES. There are 4 * 6 points rewarded, which is nice, but not correct at all.
Best, Stefan
PS: Before i forget it, i do <b>not</b> want to have all the points removed (like it happened the last time i complained), 6 of the 24 are earned and ok.

Hi Stefan,
We have closed a hole in the point system last weekend. Let us know if it happens again.
Thanks for letting us know, Mark.

Double Points for New Games?

I've been a Gamer's Club member for nearly a year now, and I've never seen the double points for any of my gaming purchases. Is there something else that I need to do to 'activate' this promotion, or is it just a glitch?
Do double points only happen when you purchase games for your 'preferred' system?

Hi house1548,
I'm very sorry to hear that our Gamers Club has only been half as awesome as it should have been for you since joining. I can imagine this has been a surprise to learn, and I want to get to the bottom of it with you!
I have reviewed your account, and everything appears to be in order, so I am not sure what may be causing the discrepancy. I have reached out to our partners on the My Best Buy team for further research, and as soon as I have more information for you I will let you know via a private message.
Thank you for being a My Best Buy member, and thank you for visiting our forum.
Best regards,
Mike|Social Media Specialist | Best Buy® Corporate
Private Message

What is the hyperfocal point for iPhone 5?

What is the hyperfocal point for iPhone 5? I was wondering what a rough estimate was so I didn't have to take multiple pictures to figure it out.

You might be interested in this App: https://itunes.apple.com/us/app/hyperfocal/id512080457?mt=8

Can I use this as a wireless access point for my network

can I use this as a wireless access point for my network

umm... use what?
A Time Capsule? Sure. It's just like many other wireless base stations. It can run in either bridge or route mode - in bridge mode it's just like an access point linking the wired and wireless networks together.

Inspection Points for Inprocess Inspection

Similar Messages

Maybe you are looking for