Install Software Does Not See the Router

Trying to install a WRT54GX4 using a DSL modem with Windows XP.
Every time that I get to the point (both the CD and the "Easy Install download) where the software is supposed to find the router I get a message that says that the wireless broadband router is not in the network. The power on, Internet, WLAN, and Ethernet lights are all on on the router.
I am an experienced computer user and have used Linksys wireless products before and have done everything that I know how to do other than manually install the puppy. Everything has been connected properly and in the correct sequence.
Thank you,
Ag

I am having the same problem.  I tried the setup using instructions from the CD included with the router, from a version of the setup downloaded from the LinkSys site, and using the interactive utility at the web site.  Everything flows smoothly along until it always fails with a message that it does not recognize that there is a wireless router connected.  I tried the online chat help from LinkSys but this was challenging since I only had a single machine and single internet conection and couldn't maintain the connection for the chat session.
I have a Westell DSL modem from BellSouth and they did confirm that my LinkSys wireless router should work OK with my existing DSL service.

Similar Messages

  • After downloading, install software does not see the internet.

    Has anyone dealt with this issue,  Please advise.

    Go to system prefs>security and privacy>firewall and make sure that PSE is allowed out.

  • HT3986 I installed windows 7 successfull, but when I start the mac in windows I does not see the wifi, and others things. How do I get the drivers?

    I installed windows 7 successfull, but when I start the mac in windows I does not see the wifi, and others things. How do I get the drivers?
    I remember that with Snow Leopard you could download them from the Apple website.
    Cheers!

    Read the Boot Camp Documentation while you run Boot Camp Assistant to download the Windows Support Software which was the first step in the Boot Camp Setup procedure.

  • Remote Desktop - The Remote Desktop administrator software does not match the installed client software version.

    Hi,
      I just upgraded to Mavricks and get this when I try to launch Remote Desktop:
    The Remote Desktop administrator software does not match the installed client software version.
    I tried removing the application and reinstalling it to no avail.  Any suggestions?
    Thanks.
    -David J. Eisen

    Hi coold88!
    I have an article for you that addresses your issue:
    Remote Desktop 3: How to install Remote Desktop Administrator software after the client software has been updated
    http://support.apple.com/kb/HT3596
    You will want to make sure you have the latest version of the software as well:
    About Apple Remote Desktop 3.7
    http://support.apple.com/kb/HT5896
    Thanks for using the Apple Support Communities. Have a good one!
    -Braden

  • Wiped our old iPad 1 clean, now can't install iOS from iTunes.  iTunes does not "see" the devise.  Tried uninstalling and installing iTunes on laptop.  Also bought new USB cable.  The iPad is charging, but that's all it does.

    Wiped our old iPad 1 clean, now can't install iOS from iTunes using laptop PC (W Vista).  iTunes does not "see" the device.  Tried uninstalling and installing iTunes on laptop.  Also bought new USB cable.  The iPad is charging, but that's all it does.  Just want to get it operating again for browsing and e-reading.

    OK.  You merely erased the content and settings.  The IOS is still there.
    If it has NEVER been jailbroke, here are some standard repair procedures.  From what you've already stated, my guess is that you'll end up with Recovery Mode described in the last paragraph.
    First, try a system reset.  It cures many ills and it's quick, easy and harmless...
    Hold down the on/off switch and the Home button simultaneously until you see the Apple logo.  Ignore the "Slide to power off" text if it appears.  You will not lose any apps, data, music, movies, settings, etc.
    If the Reset doesn't work, try a Restore.  Note that it's nowhere near as quick as a Reset.  It could take well over an hour!  Connect via cable to the computer that you use for sync.  From iTunes, select the iPad/iPod and then select the Summary tab.  Follow the on-screen directions for Restore and be sure to say "yes" to the backup.  You will be warned that all data (apps, music, movies, etc.) will be erased but, as the Restore finishes, you will be asked if you wish the contents of the backup to be copied to the iPad/iPod.  Again, say "yes."
    At the end of the basic Restore, you will be asked if you wish to sync the iPad/iPod.  As before, say "yes."  Note that that sync selection will disappear and the Restore will end if you do not respond within a reasonable time.  If that happens, only the apps that are part of the IOS will appear on your device.  Corrective action is simple -  choose manual "Sync" from the bottom right of iTunes.
    If you're unable to do the Restore (or it doesn't help), go into Recovery Mode per the instructions here.  You WILL lose all of your data (game scores, etc,) but, for the most part, you can redownload apps and music without being charged again.  Also, read this.

  • I am trying to update my iphone 3GS software but itunes just says that this is the current version of itunes, it does not see the phone update - anyone know how to get the phone updated?

    I am trying to update my iphone 3GS software but itunes just says that this is the current version of itunes, it does not see the phone update - anyone know how to get the phone updated?

    Mike
    I have done that and it is through pressing that update, which tells me that there is anew version of iphone software, that the prompt comes telling me that this is the current itunes?

  • I am trying to install a second airport express to extend my network. When I use the aiport utility it does not see the second airport express.

    I am trying to install a second airport express to extend my network. When I use the aiport utility it does not see the second airport express.

    Suggest that you perform a Factory Default Reset as follows:
    Pull the Express from power
    Wait a few moments
    Hold in the reset button and keep holding it an additonal 8-10 seconds while you plug the Express back in to power
    Release the reset button and allow 40-45 seconds for the Express to restart
    Apple's instructions to do what you want are here:
    It will often help to temporarily connect an Ethernet cable from your Mac to the AirPort Express for the setup. Once the Express is configured, you can disconnect the Ethernet cable and move the Express to the desired location.
    http://support.apple.com/kb/HT4259
    Although an AirPort Extreme is shown as the extending device in the example, the setup for an AirPort Express is exactly the same

  • I have a new time capsule (replace my old time capsule).  I want to erase my old one.  My computer does not see the old one anymore, how do I connect it (the old TC is not connected to modem)

    I have a new time capsule (replace my old time capsule).  I want to erase my old one.  My computer does not see the old one anymore, how do I connect it (the old TC is not connected to modem).  I want to erase it and then use it as either a second hard drive (sired/sirelesly?) or as a hard drive/bridge.  So,
    1.  why doesn't my cmputer see the old TC
    2  once i have solved that, how do I erase the old one
    3.  Can I use the old one as a supplemental hard drive
         a.  wired?
         b. wirelessly?
    4.  Can I use the old one as a range extender?
    I know .. a lot of questions but I would appreciate any help.
    Thanks

    sgetraer wrote:
    I have a new time capsule (replace my old time capsule).  I want to erase my old one.  My computer does not see the old one anymore, how do I connect it (the old TC is not connected to modem).  I want to erase it and then use it as either a second hard drive (sired/sirelesly?) or as a hard drive/bridge.  So,
    1.  why doesn't my cmputer see the old TC
    2  once i have solved that, how do I erase the old one
    3.  Can I use the old one as a supplemental hard drive
         a.  wired?
         b. wirelessly?
    4.  Can I use the old one as a range extender?
    I know .. a lot of questions but I would appreciate any help.
    Thanks
    1. Because it is either the same IP as the new one or hidden by being plugged in as a second router.
    To access it, isolate one computer from the existing network and plug it directly by ethernet to a lan port of the TC. Use the erase function in the TC to remove all the content of the hard disk.
    Then go to the internet tab, connection sharing and select off bridged. You can then reconnect the TC to the network.. and the computer as well. The TC will act as bridged device.. getting IP from the main router and should then appear correctly in Airport utility.
    2. I covered in 1. But you just go in airport utility manual setup. disk, and you will see the erase function. You can also set it to bridge and leave the erase until you put it back in the network.. but be careful you erase the right one.
    3. You can use the old TC via wired or wireless.. although I would always stick to wired connection if possible. Speed on wireless is 10x worse than wired.
    Also note the reliability goes down dramatically after 2 years.. a series 1 3 years old or more is ebay fodder unless you want to repair it. Do not trust vital data to it.. when it dies you will have issues recovering it.
    4. Yes, all apple routers will function as wireless extenders. when you do that the ethernet ports turn off so it becomes a purely wireless device.. strange apple decision on what you want to use your TC for.

  • Process does not follow the routing ends up in complete status

    Installed Adobe LiveCycle server ES 2.5 with SQL Server 2008 as database
    And followed the tutorial ‘Create Your First LiveCycle Application’
    Deployed it on the server when I test the same
    i.e. when the workspace user fills in form details and hits complete button it ends up as status complete
    And not assigned to next user in the route
    The process does not follow the routing it ends up in complete status
    And nothing shows up when trying to record and play back the process
    Tried invoking Via workbench too
    no errors in the server log
    Could this be an installation issue any pointers appreciated
    Please advise

    Issue with Jboss as it was taking longtime time to start due to low CPU ideally it should not take more than 3 to 5 minutes
    Process works now

  • My PC does not see the curve 8520

    my BB desktop software does not connect to the curve 8520
    I already performed the simple obvious things (chek th cable...etc)
    desktop software is release 7.1.0.32
    with the bold 9700 the software worked well
    I have to change because I crashed the screen of the bold 9700
    can anyone help?
    Roberto

    Hi and Welcome to the Community!
    Here is the list of troubleshooting articles...hopefully something will be useful:
    http://supportforums.blackberry.com/t5/BlackBerry-Desktop-Software/Tips-for-getting-BlackBerry-Deskt...
    KB10144 How to force the detection of the BlackBerry smartphone using Application Loader
    KB28457 BlackBerry Desktop Software is unable to detect the BlackBerry Smartphone due to administrative permissions
    KB28458 BlackBerry Desktop Software is unable to detect the BlackBerry Smartphone when user account control is enabled
    KB28459 BlackBerry Desktop Software is unable to detect the BlackBerry Smartphone when a full version of Roxio® Media Manager is installed 
    KB28456 BlackBerry Desktop Software is unable to detect the BlackBerry Smartphone when USB selective suspend setting is enabled
    KB28444 The BlackBerry smartphone is not detected by BlackBerry Desktop Software when connected by USB to a USB hub or a docking station
    KB28443 BlackBerry Desktop Software cannot detect the BlackBerry smartphone when it is connected via USB
    KB02640 Troubleshooting USB connections
    KB15486 Top 10 BlackBerry smartphone and BlackBerry Desktop Manager troubleshooting tips
    KB00125BlackBerry Desktop Software cannot detect the BlackBerry smartphone
    KB11439 BlackBerry Desktop Software does not detect the BlackBerry smartphone when it is connected
    KB00019 No PIN displayed in BlackBerry Desktop Redirector
    KB10938 "USB charging current is insufficient" appears on the BlackBerry smartphone
    KB01451 How to turn on advanced synchronization logging if a wired synchronization fails
    KB19717 The BlackBerry smartphone is not detected as a USB Mass Storage Device when connected to a computer
    KB16310 Media Transfer Protocol and the BlackBerry Storm smartphone
    http://supportforums.blackberry.com/t5/BlackBerry-Desktop-Software/Desktop-Manager-quot-disconnected...
    Also, check that you are using only root USB ports...no hubs (sometimes the front-side ports are hubs...use a rear USB port). And make sure to try disabling USB power management in your system configuration (Device Manager).
    Also check on conflicting software...it has been reported that the software package NTI Shadow&Ninja can cause a conflict; removing them and reinstalling the BB desktop software allows it to install correctly.
    Apologies in advance if this is redundant -- there's no way to be sure if you've already seen and tried these. Also apologies if any are not presently available...RIM takes them up and down at will as they revise things.
    Hopefully something there is helpful!
    Cheers!
    Occam's Razor nearly always applies when troubleshooting technology issues!
    If anyone has been helpful to you, please show your appreciation by clicking the button inside of their post. Please click here and read, along with the threads to which it links, for helpful information to guide you as you proceed. I always recommend that you treat your BlackBerry like any other computing device, including using a regular backup schedule...click here for an article with instructions.
    Join our BBM Channels
    BSCF General Channel
    PIN: C0001B7B4   Display/Scan Bar Code
    Knowledge Base Updates
    PIN: C0005A9AA   Display/Scan Bar Code

  • I bought Adobe Acrobat Pro XI but installing software does not recognize Acrobat 7.0 Pro for upgrade

    I bought Adobe Acrobat Pro XI but installing software does not recognize Acrobat 7.0 Pro for upgrade

    That's correct.
    Acrobat 8 is the earliest version from which you can upgrade to Acrobat XI
    http://www.adobe.com/products/acrobatpro/buying-guide-upgrade-pricing.html
    Unfortunately, Acrobat 7 is not eligible.

  • I am trying to install a brand new WD 500 gb sata internal hd in my macbook pro. the original install dvd does not recognise the hd. all hardware is ok. any help?

    I am trying to install a brand new WD 500 gb sata internal hd in my macbook pro. the original install dvd does not recognise the hd. all hardware is ok. any help?

    For some reason OS X disks (whatever edition or flavors) that are supplied with Apple products only seem to contain a limited knowledge of available hard drives on the market at the time of thier publishing. This (rather opportunistically) creates a "Best Before" stale-OS X-software-copy situation where upgrading to or replacing a defective internal SATA hard drive with a newer, better or larger one is a largely hit and miss affair.
    If you buy the latest and greatest disk drive available for any older Mac you are likely to run into unresolvable problems making a clean re-install of your own, old edition or flavor of OS X onto any newer or larger hard drive since the OEM (gray) "OS X Install Disks" that Apple supply with retail products seem to contain only time-sensitive lists/mapings of then-known target drives that the Drive Management Tool in the then-published old "Installer Software" will support.
    Presumably new (colorful "X") retail versions of OS X (10.whatever.whatever) also contain time-limited Installers with limited knowledge of and adaptability to/compatability with a limited number of old hard drives then kicking-around on the market.
    This is especially a problem nowadays since the countless "puny old" hard drives that have been on the market are largely obsolete in a few months time, as manufacturers continue to produce larger and cheaper units, discontinuing older puny products... So if your drive fails you need an exact old (or similar familial) replacement drive for your "backup copy of OS X" to do a fresh, clean OS X re-install. Otherwise you need to purchase a new retail version of OS X, since yours is now effectively obsolete. Purchasing an old, puny drive to re-install your version.flavor of OS X to avoid buying a new version of OS X is a rather false economy.
    If you still have a working old hard drive with your old polluted 10.version.flavor of OS X still working on it you apparently must clone it with Time Machine or the newest version of Disk Utility (disk image copying) to most newer, larger drives, and a clean reinstall to such new hard drives is not possible.

  • IPhoto does not see the camera

    iPhoto does not see the camera, although it worked really well for two years. Computer has been regularly updated. Please help, thank You.

    Image Capture doesn't see the camera. I have tried with two different Sony cameras, that I have been using for a long time on this computer. It is iMac 27''. Both of these cameras work normaly in MacBook Air, that means that the problem is not in the camera, or the cards. Those are the things I have tried so far. Only difference I created on the computer is that I have, two or three days ago, installed external hard drive WD My Book Studio which is connected to the computer by FireWire 800.

  • Software does not find the Database server

    Hi all,
    We are going to move database from old server MSSQL 2005 Express to the MSSQL 2008 R2 STD. For test I backuped DB from old server then restored at the new one. For some reason the software does not find the new server.
    I checked everything as from the link described:
    http://blogs.msdn.com/b/walzenbach/archive/2010/04/14/how-to-enable-remote-connections-in-sql-server-2008.aspx?Redirected=true
    Also at the new server we have another production DB that is running without any issues...
    System.Net.WebException: Unable to connect to the remote server ---> System.Net.Sockets.SocketException: A connection attempt failed because the connected party did not properly respond after a period of time, or established connection failed because connected
    host has failed to respond 195.30.95.163:80
       at System.Net.Sockets.Socket.DoConnect(EndPoint endPointSnapshot, SocketAddress socketAddress)
       at System.Net.Sockets.Socket.InternalConnect(EndPoint remoteEP)
       at System.Net.ServicePoint.ConnectSocketInternal(Boolean connectFailure, Socket s4, Socket s6, Socket& socket, IPAddress& address, ConnectSocketState state, IAsyncResult asyncResult, Int32 timeout, Exception& exception)
       --- End of inner exception stack trace ---
       at System.Net.HttpWebRequest.GetRequestStream(TransportContext& context)
       at System.Net.HttpWebRequest.GetRequestStream()
       at System.Web.Services.Protocols.SoapHttpClientProtocol.Invoke(String methodName, Object[] parameters)
       at OptoWare.OrderEntry.OrderInterfaces.WebReferenceOWEdix.OWEdixService.OWEdix_GetStatus(String custID, String password, String countryCode)
       at OptoWare.OrderEntry.OrderInterfaces.EdixInterface.b(Object A_0, DoWorkEventArgs A_1)
    2014-03-31 16:54:58,924 [1] ERROR OptoWare.OrderEntry.Controls.Config.ServiceControl - Connetction to FI1-sv-prod014\mssqlserver failed.
    System.Data.SqlClient.SqlException: A network-related or instance-specific error occurred while establishing a connection to SQL Server. The server was not found or was not accessible. Verify that the instance name is correct and that SQL Server is configured
    to allow remote connections. (provider: SQL Network Interfaces, error: 25 - Connection string is not valid)
       at System.Data.SqlClient.SqlInternalConnection.OnError(SqlException exception, Boolean breakConnection)
       at System.Data.SqlClient.TdsParser.ThrowExceptionAndWarning(TdsParserStateObject stateObj)
       at System.Data.SqlClient.TdsParser.Connect(ServerInfo serverInfo, SqlInternalConnectionTds connHandler, Boolean ignoreSniOpenTimeout, Int64 timerExpire, Boolean encrypt, Boolean trustServerCert, Boolean integratedSecurity, SqlConnection owningObject)
       at System.Data.SqlClient.SqlInternalConnectionTds.AttemptOneLogin(ServerInfo serverInfo, String newPassword, Boolean ignoreSniOpenTimeout, Int64 timerExpire, SqlConnection owningObject)
       at System.Data.SqlClient.SqlInternalConnectionTds.LoginNoFailover(String host, String newPassword, Boolean redirectedUserInstance, SqlConnection owningObject, SqlConnectionString connectionOptions, Int64 timerStart)
       at System.Data.SqlClient.SqlInternalConnectionTds.OpenLoginEnlist(SqlConnection owningObject, SqlConnectionString connectionOptions, String newPassword, Boolean redirectedUserInstance)
       at System.Data.SqlClient.SqlInternalConnectionTds..ctor(DbConnectionPoolIdentity identity, SqlConnectionString connectionOptions, Object providerInfo, String newPassword, SqlConnection owningObject, Boolean redirectedUserInstance)
       at System.Data.SqlClient.SqlConnectionFactory.CreateConnection(DbConnectionOptions options, Object poolGroupProviderInfo, DbConnectionPool pool, DbConnection owningConnection)
       at System.Data.ProviderBase.DbConnectionFactory.CreatePooledConnection(DbConnection owningConnection, DbConnectionPool pool, DbConnectionOptions options)
       at System.Data.ProviderBase.DbConnectionPool.CreateObject(DbConnection owningObject)
       at System.Data.ProviderBase.DbConnectionPool.UserCreateRequest(DbConnection owningObject)
       at System.Data.ProviderBase.DbConnectionPool.GetConnection(DbConnection owningObject)
       at System.Data.ProviderBase.DbConnectionFactory.GetConnection(DbConnection owningConnection)
       at System.Data.ProviderBase.DbConnectionClosed.OpenConnection(DbConnection outerConnection, DbConnectionFactory connectionFactory)
       at System.Data.SqlClient.SqlConnection.Open()
       at OptoWare.OrderEntry.Controls.Config.ServiceControl.i()

    It looks like the connection is getting refused because of your application configuration.
    Refer similar thread 
    http://forums.asp.net/t/1180127.aspx?A+connection+attempt+failed+because+the+connected+party+did+not+properly+respond+after+a+period+of+time+or+established+connection+failed+because+connected+host+has+failed+to+respond+
    -Prashanth

  • Audition CC does not see the CD in the drive when I try to burn

    Audition CC does not see the CD in the drive when I try to burn  CD - says no media found
    Windows 8 sees it OK

    What folders are you talking about? Photos folders? Email folders?

Maybe you are looking for