Installed a wireless canon Pixma MX432 printer back in November for use with my Mac Book Air. All was working normally until this past week when I began getting a message, "printer not connected." What is going on? Netgear Wireless N Router seems to be ok

My new canon Pixma MX432 printer is not printing. It was printing fine until about ten days ago. I use a Netgear Wireless N router, which is also new. What do I need to do. I get a message when trying to print that says "printer not connected." In addition, my old Gateway laptop will still print fine apparently because it has a cable connection to the printer. Puzzled!

Have you tried rebooting the router? I would unplug it, wait a few seconds, then plug it back in. Be sure you know the password etc. if that doesn't work, try unplugging and rebooting the printer. Good luck!

Similar Messages

Canon pixma mx850 printer not reading my computer - will not print

canon pixma mx850 printer not reading my computer - will not print
I unplugged the cord that went from the printer to the computer to another canon printer to see if I could remediate a problem with a wireless printer.
When I plugged the computer cord back into the usual computer, the printer is no longer talking to the computer even though I have gone in and changed back the settings, and it has been the default printer - that was not changed.
I've tried all the trouble-shooting suggestions to no avail.

Hi scheideckerj,
Reinstalling the latest drivers for the printer from the Canon USA website may resolve the issue you are experiencing. Please click here to go to the Drivers and Software page for the PIXMA MX850. Once on the download page, please do the following:
1. Verify that the operating system detected in the "OPERATING SYSTEM" drop-down menu is correct, and if it is not, please click the drop-down menu to select your operating system.
2. Next, please click on the red arrow next to the "DRIVERS" section and click on the MP DRIVERS file. When you do, a red DOWNLOAD button will appear. Please click on the checkbox below the DOWNLOAD button, then click the red DOWNLOAD button to begin the download. The time for the download process may vary depending on the speed of your Internet connection and the size of the file being downloaded.
Once the file is downloaded, please double-click on it to reinstall the printer drivers on your computer.
Hope this helps!
This didn't answer your question or issue? Please call or email us at one of the methods on the Contact Us page for further assistance.
Did this answer your question? Please click the Accept as Solution button so that others may find the answer as well.

When I open my RAW files in Photoshop CC they are grainy and the JPEGS are not. What is going on? It doesn't seem to have anything to do with my CACHE levels either.

When I open my RAW files in Photoshop CC they are grainy and the JPEGS are not. What is going on? It doesn't seem to have anything to do with my CACHE levels either.

BOILERPLATE TEXT:
Note that this is boilerplate text.
If you give complete and detailed information about your setup and the issue at hand,
such as your platform (Mac or Win),
exact versions of your OS, of Photoshop (not just "CS6", but something like CS6v.13.0.6) and of Bridge,
your settings in Photoshop > Preference > Performance
the type of file you were working on,
machine specs, such as total installed RAM, scratch file HDs, total available HD space, video card specs, including total VRAM installed,
what troubleshooting steps you have taken so far,
what error message(s) you receive,
if having issues opening raw files also the exact camera make and model that generated them,
if you're having printing issues, indicate the exact make and model of your printer, paper size, image dimensions in pixels (so many pixels wide by so many pixels high). if going through a RIP, specify that too.
A screen shot of your settings or of the image could be very helpful too,
etc.,
someone may be able to help you (not necessarily this poster, who is not a Windows user).
Please read this FAQ for advice on how to ask your questions correctly for quicker and better answers:
http://forums.adobe.com/thread/419981?tstart=0
Thanks!

I use a two button mouse with my Mac Book Pro. It works fine, but after installing Lion, the mouse wheel goes in reverse of what it did (rolling the wheel towards your palm goes up not down the page). Anyone know how to fix this?

I use a two button mouse with my Mac Book Pro. It works fine, but after installing Lion, the mouse wheel goes in reverse of what it did (rolling the wheel towards your palm goes up not down the page). Anyone know how to fix this?

First sentence in OPs question:
I use a two button mouse with my Mac Book Pro
I guess the track pad settings would look similar to my screen shot?
Regards,
Colin R.

TS4036 I upgraded to an Iphone 5 and open new Icloud account, I then backed up my phone on my brothers Mac Pro, I now want to restore my info to my phone and I get a message that says not enough space. What do I do

I upgraded to an Iphone 5 and open new Icloud account, I then backed up my phone on my brothers Mac Pro, I now want to restore my info to my phone and I get a message that says not enough space. What do I do

Delete all back ups on MacBook and create new back up. Restart his MB and attempt to restore again. Do not forget to erase your iphone 5 before restore.

I am getting a "connection timeout" message when trying to access my Airport Extreme with various laptops, Play Station 3 and Wii. My Airport Extreme is about a month old; it was working fine until about a week ago. C

I am getting a "connection timeout" message when trying to access my Airport Extreme with various laptops, Play Station 3 and Wii. My Airport Extreme is about a month old; it was working fine until about a week ago. Suddenly, the "timeout" is not allowing me to connect to my wireless network.

It could be that there's a new source of interference.
Use the advice in the second message of this thread to investigate the signal and noise levels that each client sees:
http://discussions.apple.com/thread.jspa?threadID=2347845&start=1
By the way, you've been misled by the poor field labeling into trying to type your entire message into the subject field, instead of putting a one-line topic description there.

TS4463 I am using Windows Vista with Outlook 2007 and iCloud. Everything has been great until this morning. I'm suddenly getting the message "Set of folders cannot be opened. The information store could not be opened.

I am using Windows Vista with Outlook 2007 and iCloud. Everything has been great until this morning. I'm suddenly getting the message "Set of folders cannot be opened. The information store could not be opened. I tried running the repair utlity to repair the iCloud however I am still getting this error message.

I tried rebooting. It didn't change anything.

Os x could not be installed on Mac book pro because storage system verify or repair failed. When i open disk utility HDD does not let me repair.

os x could not be installed on Mac book pro because storage system verify or repair failed.
When i open disk utility HDD does not let me repair.

In order to repair the system disk you must boot from another disk drive. The operating system will not allow the disk drive it is running from to be repaired.
Book the MBP and create a bootable clone on an external disk drive. Then boot from the external disk drive and repair the system disk drive from there.

I can listen to my music with samsung soundbar wh 550 but i cannot do that with my mac book air. I can connect to samsung soundbar with my mac but the connection drops immediately. Please help MacBook Air, iOS 10.9.4

I can listen to my music with samsung soundbar wh 550 but i cannot do that with my mac book air.
I can connect to samsung soundbar with my mac but the connection drops immediately. Please help.
MacBook Air, iOS 10.9.4

Contact Samsung for help.
Barry

I deleted something i should'nt have, when i power on my mac book air, all that comes up is a blinking question mark, what do i do?

i deleted something i should'nt have, when i power on my mac book air, all that comes up is a blinking question mark, what do i do?

Reinstall from Recovery Partition, hold down Command + R at power on

Canon ImagePROGRAF 6350 PRINTER NOT CONNECTED ERROR

My Canon ImagePROGRAF 6350 is connected via USB to my iMac; however, I am still getting a PRINTER NOT CONNECTED ERROR. How do I fix this?

We updated two computers on our network to 10.6.8 (from 10.5) and another (PPC iMac) to 10.5 (from 10.4). In each case, I had to first remove the printer from Print/Fax, then reinstall from the original CD, and then update to latest drivers, and then the printer worked fine. This was for a Canon 8210 Print and Scan multifunction device, so I was inferring that Canon drivers/software need to be reinstalled when updating to later versions of the OS. Hence my recommendation. The Canon website shows drivers for your device for both 10.6 and 10.7, so it appears to be usable under the latest Mac OS. It seems that if you can start from as close to "scatch" as you can and then reinstall (much as if you got the printer brand new), you have a better chance. This might involve "uninstalling" by hand if need be, to remove vestiges of the previously installed stuff.

Need wireless monochrome laser printer for home office to use with new mac book pro with retina display. I also have to have networking capability. Suggestions for economic printers?

HI, I need to buy an economic monochrome laser that will work wirelessly with new Mac Book Pro with Retina Display inmy home office. Any suggestions? I was considering the HP 1102W or Brothers HL22700W but have heard that they do not work with Mac 10.6.1 or upgrade. Need to try to get his done asap so I will appreciate any and all feedback!

http://www.shopping.hp.com/en_US/home-office/-/products/Printers/Printers

I am trying to turn on iCloud, I get a message "can not connect to server". How do I connect to server?

I can't get iCloud to turn on. When I try to start it I gat a message "can not connect to server". How do I start the cloud?

So what model and year is your machine?
Here are the requirements for ML:
http://www.apple.com/osx/specs/

Best wireless router (apple or non-apple) for use with multiple Macs

What is the best wireless router, from any manufacturer, for use with 3-5 Macs? (in a reasonable price range... sub $150)
least problems
most reliable
strongest signal/best range
fewest drops
fewest reboots

The Apple Routers "just work".
I also have a linksys. It takes a good bit of knowledge and aggravation getting it set up, but once working it does fine.
If you plan to use your router to share a printer, hook to your stereo, etc. definitely stick with Apple. It will save you much grief.

Why can't I view downloaded movies on my IPad on an airplane. I get a message Con Not Connect. Didn't use to have this problem

Why can't I play a downloaded on my IPad in an airplane? Error message CAN NOT CONNECT. Didn't use to have this problem.

Hi Dakota27,
Thanks for visiting Apple Support Communities.
You may find this article helpful with troubleshooting email on your iPad:
iOS: Troubleshooting Mail
http://support.apple.com/kb/ts3899
Regards,
Jeremy

Installed a wireless canon Pixma MX432 printer back in November for use with my Mac Book Air. All was working normally until this past week when I began getting a message, "printer not connected." What is going on? Netgear Wireless N Router seems to be ok

Similar Messages

Maybe you are looking for