Installing Leopard on an iMac G5 currently running Panther!

HI,
I heard a rumour that I might not be able to install Leopard on my iMac G5 currently running fine on 10.3.9 Panther, at least, not before I install Tiger. Is this true? I had hoped I could just buy Leopard and install that. Surely I don't have to track down a copy of Tiger and install that first?
Only reason particularly for upgrade is have bought some new iPods and they won't work with Panther :-(!!
Any advice would be gratefully recieved.
Ed.

MilkyJoe wrote:
HI,
I heard a rumour that I might not be able to install Leopard on my iMac G5 currently running fine on 10.3.9 Panther, at least, not before I install Tiger. Is this true? I had hoped I could just buy Leopard and install that. Surely I don't have to track down a copy of Tiger and install that first?
Only reason particularly for upgrade is have bought some new iPods and they won't work with Panther :-(!!
Any advice would be gratefully recieved.
Ed.
Just install Leopard directly. I suggest an Archive and Install and then migrate your stuff back. Many old apps and programs will not run with Leopard. Sherlock, to name one. Also be careful of your 3rd party apps. Some have been trouble.
Use SuperDuper or CarbonCopyCloner to make a full bootable backup of Panther and then test it by booting into it. You then have the best of both worlds - a dual-boot system with Panther and Leopard.
If you partition your external drive for Panther in a small partition and leave the rest for TimeMachine backups, you are really set.
I have my external TM drive with Tiger in a small partition. It boots and once and a while I run it to keep it from getting lonely

Similar Messages

  • Hi I am trying to install snow leopard, Hi I am trying to install snow leopard onto my iMac g5 currently, Hi I am trying to install snow leopard onto my iMac g5 currently running 10.3.9. I open disk ,click install- nothing happens. Any ideas? Thanks Dan

    Hi I am trying to install snow leopard onto my iMac g5 currently running 10.3.9. I open disk ,click install- nothing happens. Any ideas? Thanks Dan

    Snow Leopard requires an Intel-based Mac, so as Niel indicated your iMac G5 cannot run it. The last version of Mac OS X your iMac G5 can run is Mac OS X 10.5.8.
    Regards.

  • My imac is currently running on Snow Leopard 10.6.3 How do I upgrade to install Mountain Lion?

    My imac is currently running on Snow Leopard 10.6.3.  How do I install Mountain Lion?

    Update your 10.6.3 to 10.6.8 using the :
    http://support.apple.com/kb/index?page=answerlink&url=http%3A%2F%2Fsupport.apple .com%2Fkb%2FDL1399&answerid=16777216&src=support_site.downloads.search
    Mac OS X 10.6.8 Update Combo v1.1
    Then make sure you meet the requirements for Mt Lion:
    http://www.apple.com/osx/specs/
    Now that being said, the 2GB RAM requirement will not leave you with a smoothly running system. Max out your RAM that your system can handle (more than 8 GB would be up to you) . Older Applications may no longer supported. No Power PC apps are supported past !0.6.8. Many other Apps will need to be updated or upgraded.

  • Trying to install Leopard on my iMac (G5).  Got to the screen that asks for the user name and password and it won't take it.  How do I get out of this and resume the software install?

    Trying to install Leopard on my iMac (G5).  Got to the screen that asks for the user name and password and it won't take it.  How do I get out of this and resume the software install?

    Help here >  Mac OS X: Changing or resetting an account password

  • How to install Leopard in my iMac if it has no DL-DVD player?

    How to install Leopard in my iMac if it has no DL-DVD player?
    My eMac is:
    eMac G4/1.25 (USB 2.0) with 2GB RAM

    Most PPC Macs cannot boot OSX from USB, they need Firewire... that being said, out of 13 PPC Macs I had one that booted from USB Drives, including Flash Drives, it was my eMac/1.42GHz as a matter of fact, USB drives would show as a boot choice if I held the Option/alt key at bootup, (nowhere else), but It lost that ability when I reset the NVRAM.
    The USB boot workaround that works for some is...
    Connect the drive to your machine, and find out which partition the OS X system is installed on. I usually find this by going to Disk Utility and looking at the info for the partition on the USB disk with OS X. That is, disk2s3 is usually for a USB disk with no OS 9 drivers installed that is the second disk disk. disk3s9 might be a USB disk with OS 9 drivers that is considered the third disk. There are other ways of finding this out, but in my case, my disk is disk2s3 (the 3 on the end will come into play soon).
    Start up the machine in Open Firmware (this is the fun part). Hold Command-Option-F-F right after the machine is turned on.
    Here is the moment of truth. If this step does not work, I have had very limited success getting a machine to boot off USB2. In Open Firmware, type devalias, and you should get a list as output. In this list, look for ud, usually below where you see hd (ud is "USB Disk," I presume). If found, it will usually have beside it /pci@f2000000/usb@1/disk1, or something similar. Again, if you see this, I have not had this fail yet.
    Now type printenv boot-device, which will usually get you output of boot-device hd:,\\:tbxi. (See where this is going yet?)
    Type setenv boot-device ud:3,\\:tbxi where the number after the colon corresponds to that partition number we found in step two. You should get an ok back.
    Type printenv boot-device, and you should see the change displayed already. Something like:
    boot-device        ud:3,\\:tbxi        hd:,\\:tbxi"
    http://hints.macworld.com/article.php?story=20060301112336384
    You'd need to clone the Install Disc to a Flash Drive, or make a DMG of it then Restore it to the Flash drive.

  • I have a 2006 iMac and currently run Snow Leopard. I want to upgrade to Lion, but don't know if my computer is too old to run OS 10.7

    I was hoping to upgrade to Lion 10.7 in order to utilize iCloud with my iPhone.  However, I cannot determine if the OS 10.7 is compatible with an 2006 iMac.  I am currently running Snow Leopard.  Everything I've looked at on the Apple Site shows the newer OS on a laptop with a touch pad.  Does this disqualify an iMac?

    Correct, they are different generations of processors. The Core 2 Duo being a 64bit processor. The Core Duo being 32 bit. Lion needs a 64 bit processor.
    You would think the chip manufacturers could come up with more distinct names. :-)
    Stedman

  • Unable to install Leopard onto my iMac G5

    This is my first post here so please be patient with me if I do not do a good job explaining my problem.....here we go.
    I have a 20" iMac G5 purchased back in 2004. It is what I believe was referred to as a special edition and came with a wireless keyboard and mouse. It currently has the minimum 512 megs of ram (I've ordered 2 Gigs for it yesterday), 150Gig HD, 1.8Ghz (not at the computer right now so cannot confirm the CPU speed). It currently is running OS 10.4.11. Ok, now onto the problem.
    I tried to install Leopard Family edition, which I purchased at an Apple Store. I have tried and failed to install 10.5 four times now. The first attempt would not even pass the DVD check. It says the install DVD is damaged. That is not true because it loaded just fine on my wife's 12" Macbook.
    In any event, I do have an external HD which is used for backup, via SuperDuper. Therefore, I have not lost data in case you are wondering. Each time I installed I would select the erase and install option. Each time, I get a different error. It will pass the DVD check then fail about 15 minutes into the install. It will give a yellow triangle window and say the Source Media is damamged. Another error in another install attempt says something to the effect that it cannot find something (cannot remember what) on the destination drive.
    After these attempt, I reinstalled 10.4 and managed to get the system running again. I repaired permissions and ran the Verify Disk from Disk Utility and everything checks out. I had a technician come help me and ran DiskWarrior and seem to believe the HD and permission are fine.
    I have had a few problems prior to the Leopard install, which may be the problem to begin with. Mainly two problems, the computer will not always come out of sleep mode when clicking the mouse and/or keyboard. I also have had many Kernel Panics. These two issues have ocurred over the last year but have increased in frequency. Have not seen a Kernel panic since I reinstalled 10.4.11 but still will not always come out of sleep mode. BTW, I did get a USB keyboard (not apple) and a mac mouse and have been using them since last night.
    Ok I will stop here for now. I aplogize for wordiness and disorganization. Please help..

    I received my external DVD drive and tried to install Leopard. No success. I get the same error. It appears to fail about the same time. It spends some time doing work before it calculated the estimated install time. Just after it calculated an install time (about 3 hours) that is when I get installation failed error. To me, it would eliminate the internal optical drive.
    At this point, I am at a loss of options. I could replace the Hard Drive next I guess. I am beginning to wonder if I should just save my money and buy a refurbished Intel iMac....
    I did buy 2 Gigs of RAM (EDGE) which is supposed to be compatible with my system. When I installed it the computer would start buy the screen stays dark. About 30 seconds after startup the cpu fans spin up to full rmp and the computer remains that way until I hold in the power to power down. I tried removing the RAM one at a time and still no joy. I finally removed it and reinstalled the 512 ram and the computer booted no problem. I have already talked with the site I bought it from and I am going to send it back.
    If anyone has anymore comments I would be most appreciative for additional help.

  • Installing leopard osx on imac g4

    I recently was given an 15 inch iMac G4 with 256 MB RAM and 800 MHz processor and was running OS X 10.3.9. I upgraded the RAM to 512 MB and installed Leopard using a firewire connection with my MacBook. I can boot from the MacBook Leopard but the iMac will not boot or seem to find the Hard Drive. I can see the Hard Drive on my MacBook with Leopard installed on it. All I get on my iMac is a "finder" with a question mark. Is there any suggestions or tips about how I can get my iMac to run properly using Leopard????

    You can't do it that way, because one Mac is Intel and the other is PowerPC. And it's not because the OS installation is different. It's because of something more obscure called the +partition map scheme+ of the hard drive.
    For a drive to be bootable on a PowerPC Mac, the +partition map scheme+ needs to be +Apple Partition Map+. For an Intel Mac, it is called +GUID Partition Table+. An Intel Mac can actually boot a drive that is either +Apple Partition Map+ or +GUID Partition Table+; however, when you run Installer to do a Mac OS X installation, if you are using an Intel Mac (such as a MacBook) to run the installation, it will insist that the +partition map scheme+ of the drive is +GUID Partition Table+.
    Therefore, because you used FireWire Target Disk Mode to run the installation from the MacBook targeting the iMac hard drive (as its external drive), the +partition map scheme+ ended up being +GUID Partition Table+. A PowerPC Mac that has Tiger or later can access a drive that is +GUID Partition Table+, but can only boot the drive if it is +Apple Partition Map+.
    What you may be able to do instead, is the following.
    Use the MacBook to install a fresh Leopard installation onto an external drive. Restart from it and run Software Update, and make sure it is working. Then restart from the MacBook's own drive again.
    Connect the iMac using FireWire Target Disk Mode to the MacBook as you did before. Use the MacBook to erase the iMac's hard drive using Disk Utility. Instead of using the Erase tab, use the Partition tab. Reset the +Volume Scheme+ to *1 Partition*. Click the Options button, and select *Apple Partition Map* there as the +partition map scheme+. Back on the main window, name the volume and set the format to *Mac OS Extended (Journaled)*, and Apply it.
    Now, you have the iMac's hard drive with the proper +partition map scheme+ and format. Use a cloning utility, such as Carbon Copy Cloner or SuperDuper, to clone the fresh Leopard installation from the external drive to the iMac's hard drive. Since cloning is done at the volume level, not the drive level, you should get a bootable clone of the Leopard installation on a drive that can be booted by a PowerPC Mac.
    Leopard is universal so I think the above method will work. However, there may be complications such as the proper drivers for an 800 MHz iMac G4 not being present in the Leopard installation, because Apple does not officially support that model with Leopard.
    Note: To be legal, the Leopard license you are using must not be currently used on another Mac. If the MacBook is currently using that Leopard license, you should not do it for legal reasons.

  • Can I install Leopard on an external drive to run my computer?

    Since it seems my hard drive has totally bit the dust, can I install Leopard on the external drive I use for Time Machine, and run my desktop from that drive? Could I run it from an external drive totally dedicated to Leopard? I am buying a new desktop soon, but I need info off of this machine. Can I plug in my Time Machine drive to my laptop and be able to use it without losing data?

    Elizabeth Salcido wrote:
    Thanks so much.
    Youa re welcome!
    I figured I would have to use a second drive. At least when I get my new desktop I will have a drive for Time Machine for both desktop and laptop.
    If you really plan to keep the laptop around after you get your desktop, I would recommend replacing its internal hard drive. While running your laptop off an external is possible, it should be considered a stopgap measure. i wouldn't do it on a permanent basis. For one, as you'll find out, it's quite a bit slower than when using the internal drive.

  • Installing leopard on G3 iMac??

    1 - I have an old vintage g3 iMac that I sometimes use for certain specific applications; three (?) years ago I spruced it up by installing Tiger, now I was thinking of doing the same by installing leopard. is that even a good idea?
    2 - unfortunately, the disc drive on the iMac doesn't work; I tried installing leopard via an external FW disc drive, but no good - it just tried and tried to boot from the DVDROM for 40 minutes before I gave up.
    3 - I was thinking of trying to burn two DMG files from my Leopard install discs, and then put them (via the network) on the G3 iMac. Is that a good idea? Is it possible to install leopard from DMG files?
    thanks - appreciate any feedback.
    w

    nuts! well, that DOES answer my question - even though it's NOT the answer I wanted to hear!
    thanks!
    I have to reinstall apple remote desktop on my Mac Pro and see if I can connect to the iMac that way; as of now, I can only connect to the public drop box on the iMac - I have to fool around with the file sharing stuff in the preferences... thanks again...
    w

  • Installed Leopard and now MacBook can not run on battery

    I installed Leopard and now if it is disconnected from the power it will shut down immediately. It worked fine before.. How do I fix?

    You might try to reset the SMC (System Management Controller) and/or PRAM (Parameter Random Access Memory). Mac OS X: What's stored in PRAM?

  • How do I install Snow Leopard on a MacBook Pro currently running Lion?

    A friend is having trouble running older apps in Lion on his new Macbook Pro and wants to revert to Snow Leopard. Any suggestions or cautionary tales appreciated. Thanks.

    New MBPs require a version of Snow Leopard that you cannot purchase. If it did not come pre-installed on the computer then installing Snow Leopard is a bit of a chore.
    First off he will need a computer that can boot from a retail Snow Leopard DVD (10.6.3.) Second off he will need a 16 GB USB flash drive or a free partition on a USB hard drive that is at least 16 GBs in size. The basic process is:
    Using a computer that can boot from a retail Snow Leopard DVD you install 10.6.3 onto the spare drive. Download and install the 10.6.8 Combo update. Create a new partition on the MBP. Boot the MBP from the 10.6.8 USB drive then clone the system to the new partition on the MBP.
    I will be glad to provide more detail if needed.

  • Should I try to install Leopard on an iMac G5 (not intel)

    Hi,
    I've looked in to this a bit and it seems I should be able to.
    I'm just concerned that while it might not fail, it might not behave brilliantly either!
    I've got my Leopard 10.5.8 install disc to hand, my current machine spec should be quoted in the footer to this post.
    Any advice?

    Yep - I did on my G4 Powerbook last week and it's fab. Runs faster than Tiger if anything. I took advice from the Low End Mac website and upgraded to the max 2GB RAM first or perhaps it wouldn't have been such a good idea.
    I see you've maxed the RAM on yours already - go for it!
    I'm waiting for the RAM for my iMac then I will be right behind you

  • Where can I find the snow leopard upgrade.  I am currently running leopard 10.5.8

    I have been searching through the apple store to upgrade my current os - 10.5.8? To upgrade to lion, it appears I need to have snow leopard 10.6. However, I cannot find the upgrade in the apple store.

    Start by checking if you cn run Snow Leopard:
    Requirements for OS X 10.6 'Snow Leopard'
    http://support.apple.com/kb/SP575
    Whilst Apple have withdrawn Snow Leopard from their stores, you can still get it from Apple by calling 1-800-MY-APPLE (if you are in the USA) and they will supply the SL DVD for $20 for a single user, or $30 for a family pack that covers up to 5 Macs.  You can also purchase the code to use to download Lion from the same number (Lion requires an Intel-based Mac with a Core 2 Duo, i3, i5, i7 or Xeon processor and 2GB of RAM, running the latest version of Snow Leopard), or you can purchase Mountain Lion from the App Store - if you can run that:
    http://www.apple.com/osx/specs/
    If you are outside the US call your national Apple Helpline:
    http://support.apple.com/kb/HE57
    If you're in the UK, use this number: 0871 508 4400
    When you have installed it, run Software Update to download and install the latest updates for Snow Leopard.

  • Installed Leopard on my iMac G-5, bad idea

    I have been running OS X 10.4.11 (Tiger) for quite a while. A friend tempted me to upgrade to Leopard with their disks. I also wanted to purchase the ScanSnap scanner which needs Leopard to run, as well as Bento 3.0 which also requires Leopard. Well now I feel that upgrading to Leopard was a big mistake!!! Now I don't have iPhone syncing, iCal search capability, iPhoto transfer to my iPhone and no printing on Address book. I still run into some new surprises every day. I had absolutely no problems with Tiger. Could it be my 667 Bus speed or my non Intel hardware? Whatever it is, I'm ready to pull my hair out trying to find the problems. I've spent hours on the discussions reading everything I could and found nothing that worked. Even after subscribing to MacUpdate, it won't open. I also thought of purchasing MobilMe to sync everything but am not sure that would work if I'm having the current problems. I'm ready to go buy a new iMac but am afraid the problems to the new machine will only transfer. Does anyone have a solution. I would return to Tiger but after reading some of the discussions, it may not be possible to go backwards without making even more problems. BTW, already have a lot of scanning done (no problems with the Fujitsu 1500M) but still want to continue so I'm frantically scanning as fast as I can so if I do return to Tiger, I will at least be able to access what I scanned! Sorry I upgraded!! Thought also of going to the local Apple store counter and sharing my stories. No doubt my unit is out of warranty.

    A friend tempted me to upgrade to Leopard with their disks.
    What's wrong with this picture?
    It is THEIR discs. They are the only ones licensed to use those discs.
    Furthermore, if it is really an iMac G5, unless the discs look like * they are not designed to work with your machine. They are only designed to work on the machine whose label is on them. Thus any flaws you see in the installation are due to using the wrong discs. Furthermore the last iMac G5 left the market prior to Leopard's arrival, so if the discs say Upgrade, DropIn, or OEM they won't work on your iMac in any case.
    Now many also confuse the iMac G5, for iMac Intel. These are totally different beasts, even though externally, they look identical. Look on the base of the iMac in question. If it has an EMC# of: 2104, 2105, 2110, 2114, 2118, 2111, 2133, 2134 it is an iMac Intel, and not an iMac G5. iMacs which look like are iMac Intel as well. Those which may use Leopard Update discs are iMac Intel whose serial number begins: xx742xxxx to xx744xxxx where x can be any letter or number.
    If you want Leopard for your Mac, you can usually call Apple Store sales, as they often have discs for sale. But do not use another person's discs. It is against license agreement, unless they remove it from all of their machines.
    - * Links to my pages may give me compensation.

Maybe you are looking for