IOS Software MTP
I have a requirement to provide an MTP to allow FastStart on a H.323 gateway working with CCM4.1(3). Since all codecs used will be G.729a, I have tried to configure a resource on a 3845 router. It has no DSP's or voice modules, so I have tried to configure it as a software only resource but can't seem to get it to register with CCM.
I have followed guideline in "Configuring Enhanced Conferencing and Transcoding for Vice Gateway Routers" but don't seem to see registration attempts on CCM. Router shows sccp admin state UP, Software MTP Oper State: ACTIVE_IN_PROGRESS - Cause Code: TCP_CONN_ERROR.
Can anyone confirm that I am right in the assumption that I need no other hardware to do this successfully? Any ideas as to what is going wrong?
Cutdown running config:
interface GigabitEthernet0/0
description *** Trunk to switch ***
no ip address
duplex full
speed 1000
media-type sfp
negotiation auto
interface GigabitEthernet0/0.5
description *** VOIP VLAN5 ***
encapsulation dot1Q 5
ip vrf forwarding cust58
ip address n.n.243.1 255.255.255.128
no snmp trap link-status
interface GigabitEthernet0/0.6
description *** Back Office VLAN 6 ***
encapsulation dot1Q 6
ip vrf forwarding BackOffice
ip address n.n.243.130 255.255.255.192
no snmp trap link-status
interface Serial1/0
no ip address
encapsulation frame-relay IETF
load-interval 30
dsu bandwidth 44210
frame-relay traffic-shaping
interface Serial1/0.271 point-to-point
description *** PVC for VOIP ***
ip vrf forwarding cust58
ip address n.n.100.58 255.255.255.252
frame-relay class VOIP-1024kbps
frame-relay interface-dlci 271
interface Serial1/0.272 point-to-point
description *** PVC for Backoffice ***
ip vrf forwarding BackOffice
ip address n.n.100.62 255.255.255.252
frame-relay interface-dlci 272
sccp local GigabitEthernet0/0.5
sccp ccm n.n.243.211 identifier 10 version 4.1
sccp ccm n.n.243.210 identifier 20 version 4.1
sccp codec g711alaw mask
sccp codec g729r8 mask
sccp codec g729br8 mask
sccp codec g729abr8 mask
sccp codec gsmfr mask
sccp codec gsmefr mask
sccp
sccp ccm group 999
associate ccm 10 priority 1
associate ccm 20 priority 2
associate profile 12 register MTP00169D43E1A0
signaling dscp af31
audio dscp ef
dspfarm profile 12 mtp
codec g729ar8
maximum sessions software 20
associate application SCCP
gateway
timer receive-rtp 600
Similar Messages
-
I currently have 3 call manager clusters.
Cluster 1
Cluster 2
SME Cluster
I have two 3900 gateways currently connected to cluster 2 that are configured for as 500 software MTP's. That is all these gatways do now, nothing else.
I would like to share these software MTP's with the other 2 call manager cluster. I do not see a way to do this.
Is it possable to share the software MTP's between mulitple CUCM 9.x clusters?
Thanks in Advance!You cannot share the same dspfarm. You can however create separate dspfarms (subdividing the total capacity in the process) and separate call manager groups which point to separate clusters.
Please remember to rate helpful responses and identify helpful or correct answers. -
My iPad2 went blank. Troubleshooter says driver software MTP USB problem, what do I need to do?
My iPad2 went blank. Troubleshooter says driver software MTP USB problem, what do I need to do?
iOS: Resolving update and restore alert messages
For error -50: See error 13 and 14:
Error 13 and 14: These errors are typically resolved by performing one or more of the steps listed below:
Perform USB isolation troubleshooting, including trying a different USB port directly on the computer. See the advanced steps below for USB troubleshooting.
Put a USB 2.0 hub between the device and the computer.
Try a different USB 30-pin dock-connector cable.
Eliminate third-party security software conflicts.
There may be third-party software installed that modifies your default packet size in Windows by inserting one or more TcpWindowSize entries into your registry. Your default packet size being set incorrectly can cause this error. Contact the manufacturer of the software that installed the packet-size modification for assistance. Or, follow this article by Microsoft: How to reset Internet Protocol (TCP/IP) to reset the packet size back to the default for Windows.
Connect your computer directly to your Internet source, bypassing any routers, hubs, or switches. You may need to restart your computer and modem to get online.
Try to restore from another known-good computer and network. -
My iPad 4 does not show up on my TV screen when in AirPlay mirroring mode using WiFi. The iPad displays AirPlay set to TV with the Mirroring On (green).
My iPad IOS software is 8.2 and my Apple TV software is at 7.1. The TV displays the Apple Menu. The “Settings” does however displays the General menu allowing me to see:
Apple software: 7.1 (7003)
Apple TV: Model No. A1464, Part No. MD199B/A
Signal Strength shows 5 circles.
It does not display the iPad screen but when I use the BT Sport App I can hear the sound but there is no video. I have searched the internet for a solution to no avail. The problem first arose when the IOS was at 8.1+ but it worked correctly briefly when I updated to IOS 8.2. Can you help please?Welcome to the Apple Community.
Try the following steps, check whether things are working after each step where appropriate, before trying the next.
Check AirPlay is turned on on the Apple TV (turn it off and on if it already is)
Check that both devices are on the same network (Settings > Wifi, on the mobile device and Settings > General > Network, on the Apple TV).
Restart the Apple TV (Settings > General > Restart).
Restart the Apple TV by removing ALL the cables for 30 seconds.
Restart your router. (Also try removing it’s power cord for at least 30 seconds)
Restart your mobile device.
If you are still having problems, the following article(s) may help you.
Troubleshooting AirPlay
Troubleshooting Wi-Fi networks and connections
Recommended Wi-Fi settings
Wifi Diagnostic Software (for Mac users)
You may also find some help on this page, where I’ve collected some of the more unusual solutions to network issues.
When making adjustments to your network for better optimisation, you may find some of the points mentioned on this page helpful. -
I updated the latest version of iOS software on my Macbook Pro and now when I try to open up iPhoto it says that I need to update the latest version. But when I go to update on iTunes, it says the latest version is unavailable to the U.S. I wouldn't mind leaving it be but I can't access any of my photos. What do I do?
stuckoncc wrote:
I updated the latest version of iOS software on my Macbook Pro
iOS is on iPhones and iPads.
Are you using an iPhone or iPad? -
How do I update the iOS software on iTunes for Windows
Hi all.
The battery life in my phone was decreasing very quickly to the point where I have turned it off with 100% at night, and wake up in the morning to have it at 0%. So yesterday, after making a few calls I got to this nice man who explained to me that it was not a problem with the battery, but I needed to update to the latest version of iOS (generally fixes the problem). I don't have enough space (and cannot clear it), so he suggested another option. I would have to use iTunes. First he told me to upload my data to iCloud. As I have not done it before, it took a while, and it did not work for a while. He sent me the link of what to do via email (Update the iOS software on your iPhone, iPad, and iPod touch - Apple Support) and hung up, after me thanking him. My cloud finally updated a little before 10PM GMT and I went to sleep. In the morning my battery was not dead, albeit it had only gone done by a few %. However, I still want to update to the newest software.
I have the latest version of iTunes on my laptop and so this morning I plugged in my phone to my laptop (using the computer - phone plug). However I cannot see where to select my device. My phone is not coming up in any corner, and it is not charging when it is plugged into my laptop either (I read somewhere that it should). So my question is, how do I select my device. It is plugged in but it not coming up for me. Please be as explicit as possible.
If it helps I have an iPhone 4s bought in December 2013.
Thank you!I'm not sure if it should be here or in the iPhone usage forum.
-
I have an older iPod Touch, Model MC086LL with an IOS software version of 4.2.1. Many of the applictions which I had previously purchased were recently upgraded and they no longer can be loaded on my iPod. What is the fix?
Reload older versions from iTunes on a computer, or buy a newer device.
(73016) -
I Downloaded the new iOS software on my iPod touch now when I turn it on it has a USB cord and says connect to computer and iTunes, well the only other
No. You have to connect the iPod to a computer and restore via iTunes.
For how to restore:
iTunes: Restoring iOS software
To restore from backup see:
iOS: How to back up
If you restore from iCloud backup the apps will be automatically downloaded. If you restore from iTunes backup the apps and music have to be in the iTunes library since synced media like apps and music are not included in the backup of the iOS device that iTunes makes.
You can redownload iTunes purchases by:
Downloading past purchases from the App Store, iBookstore, and iTunes Store
Find a friend or go to an Apple store. -
I backuped my iphone 3 when it had a higher IOS software. After i restored my Iphone, i eneded up having to downgrade the IOS software in order for it to fully restore. Now when i try to back up my phone, it says that my iphone is too old for the backup. If i DO upgrade the IOS, i won't be able to use my phone because it becomes too slow and wont even fully restore.
ThanksIf your phone is in recovery mode (You see the iTunes graphic on the phone), you MUST connect the device to a computer and restore the operating system. There is no supported way to get around it. The device had a problem installing the update and it crashed. Sorry.
-
Hi.
I have a 4g iphone without the IOS software ( or the latest version of it.) I have exhausted the devices that I can exchange info. on which I believe is 5. 3 o out of the five broke. I am able to sync my phone and get apps, books, and music (thankfully from my phone to my latest computer, but not vice versa. In order to update and downlaod the IOS software it says I need to back up all of my info. Will purchasing the latest subscription of icloud 24.99 per year help me or should I just excpet that I will lose my lateset notes, text messages, and contacts through the update. I also want to make sure that after I update, I will be able to get all of the info back onto my phone. Any help would be greatly appreciated.
Thanks.See:
Recovering your iTunes library from your iPod or iOS device: Apple Support Communities
To copy iTunes purchases to the computer you have to log into (authorize) the account that purchased them and them transfer
iTunes Store: Transferring purchases from your iOS device or iPod to a computer
When associating a device with an Apple ID see the following regarding the 90 day limit. -
I was asked to update my IOS software on my iPhone 4, and now it is giving me no other option than to plug it into iTunes and restore it, I dont want to lose everything, is there anything I can do?! Please help!
The next thing to check is your router. It may be blocking the port needed to access the Apple servers. Check that ports 80 and 443 are not blocked. Your ISP may also be blocking access to the Apple servers. Verify that you can ping albert.apple.com and/or phobos.apple.com.
Also, an invalid TcpWindowSize entry in the Windows registry can cause problems. run Regedit and search for TcpWindowSize; if the entry exists this might be the problem. Export the entry and delete it, then try again. If this fixes it after updating be sure to reload the entry (by double-clicking the .reg file that you saved it to). -
I am having issues with streaming music from iTunes on my MacBook Pro to my audio system through AirPlay. Works perfectly with my iPod Touch. The AirPlay icon appears irregularly in iTunes and when selected doesn't connect. Running latest IOS software.
Try:
- Reset the iOS device. Nothing will be lost
Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Unsync all music and resync
- Reset all settings
Go to Settings > General > Reset and tap Reset All Settings.
All your preferences and settings are reset. Information (such as contacts and calendars) and media (such as songs and videos) aren’t affected.
- Restore from backup. See:
iOS: How to back up
- Restore to factory settings/new iOS device.
If still problem, make an appointment at the Genius Bar of an Apple store since it appears you have a hardware problem.
Apple Retail Store - Genius Bar
You said:
No, I do not want to "factory reset" my iPod. No I do not wish to do anything crazy long or hard to fix this.
That may be necessary, It is not what you want to do/not do but what is required to resolve your problem. -
None of the above have worked. Ipad completely bricked. This began when merely updating IOS software as instructed. Now Apple want to charge me for using their crappy software as directed. Surely this is not only immoral but potentially illegal.
Read: iPad Troubleshooting Assistant
That procedure eventually leads you to the need to restore it.
Make sure you are following the instructions in this procedure to the letter. Here they are, with emphasis on some easily overlooked requirements:
Disconnect the USB cable from the iPad, but leave the other end of the cable connected to your computer's USB port.
Turn off the device: Press and hold the Sleep/Wake button for a few seconds until the red slider appears, then slide the slider. Wait for the device to turn off.If you cannot turn off the device using the slider, press and hold the Sleep/Wake and Home buttons at the same time. When the device turns off, release only the Sleep/Wake button.
Continue pressing and holding the Home button while you reconnect the USB cable to the device. The device should turn on.Note: If you see the "low battery" screen, let the device charge for at least ten minutes to ensure that the battery has some charge, and then start with step 2 again.
Continue holding the Home button until you see the "Connect to iTunes" screen. When this screen appears (iTunes icon and USB connector) release the Home button.
If necessary, open iTunes. You should see the "recovery mode" alert ("iTunes has detected a phone in recovery mode").
Use iTunes to restore the device.
If you do not see the "Connect to iTunes" screen, try these steps again. Be patient since it sometimes takes several of these attempts before you are successful.
If you see the "Connect to iTunes" screen but the device does not appear in iTunes, see this article and its related links.
Select the iPad in iTunes and choose "restore from backup". This assumes you have a backup. If you do not, you will have to download all your purchased iTunes content again. You do not have to pay for anything you already purchased.
If you still can't get it to work, you have done all you can and only Apple will be able to help. -
I have just updated my ipad mini with the new ios software and it has caused may ipads onboard keyboard to run very slowly does anyone no how to fix this issue
*Typing lag iOS 7*
Settings>General>Reset>Reset all settings. This should improve the typing responsiveness
*Note:* Settings, preferences, network settings, etc will be reset. *NO data or media will be lost*
and/or
Settings>iCloud>Documents and Data (turn it OFF) -
I can't turn my wifi on with the new iOS software
I can't turn my wifi on with the new iOS software. I've tried resetting the network settings, resetting all settings, and a hard reset.
Read here:
http://support.apple.com/kb/ts1559
If nothing works, make an appointment at any Apple store.
Maybe you are looking for
-
SAP Server has lost connection to the database!
Hi Gurus, Can some please guide me on this " SAP Server has lost connection to the database! " what need to be check. OS : AIX DB : DB2 thanks vamsi
-
Text is missing in migo - excise invoice tab
Hi, I'm doing migo with excise invoice tab option, where on the left, there are options like, capture & post, part1 only, no excise entry .etc.. In that area if i use F4 option, i can see both the fields i.e field nbr as 01 and text as capture and p
-
Apple TV and Pioneer 50in Plasma
Hi All This is my first time posting here. I just purchased an Apple TV and have tried to connect it up. I have a pioneer set top box, pioneer DVD player and recorder and pioneer Receiver. I can see an HDMI plug on the receiver but when I connect it
-
Forgot startup password for my Satellite Z930
I forgot my password for my z930. I bought the laptop from a market, it was working fine then I put a password on it. And now I have forgotten the password. I heard there is a response code that I can get, there was a shift tab thing I did which let
-
How to change code completion package proc name be inserted in origin case?
Hi, it seems like the code completion for package function/procedure name is inserted in UPPER case. Is it possible to configure it to insert the name according to the exact case like what I typed in the package? Please advise. Thank you.