IOS8 music control through usb in car (Jeep & Volvo)

after updating both mine and my wife's iPhone5's and to iOS8 our in car controls started working intermittently for actually starting, skipping, pausing, etc.. playback of our iPhones both in my 2011 Volvo S40 and her 2014 Jeep Cherokee (through USB connection, which previously worked with no issue).
we then upgraded our phones to iPhone6's and same issue (after updating to one the next small iOS8 updates the issue was slightly less intermittently, but still sporadic and very unreliable; 8.1.3 update made no difference).
control works perfectly through bluetooth streaming in her Jeep, however.
I assume there were changes made to the music playback control (trickplay) mapping in iOS8, is there a ticket out to fix this or is the issue even know?
Are others having the same issue?

I went here: https://rsur.extra.chrysler.com/rsur/Uconnect.do
You have to have a flash drive to install the image to and plug the USB into your Jeep. Haven't tried that yet but will tonight.

Similar Messages

PWM control through USB 6008/09

Hello all
I have already read a thread regarding the topic but i am not satisfied with the replies.
I have discovered few programs that can run PWM in LabView, but they all are for DAQmx. So, will those programs run through USB 6008? and i also read that the output will be a sort of slow response output?
I am aiming to power a micro-pump rated at 12VDC. So, i want to run the program in LabView, use the USB 6008 to connect to a the DC motor. I know that some amplification will be required because the output of the USB 6008 is rated as 0-5V.
But, my question is can i successfully control the speed of the DC micro-pump ( motor) using the USB 6008??
Regards
Nikhil
Many more kudos to give
Many more Kudos to give

Thanks for the reply.
If you just need to output voltages(not PWM) then you can use the Analog outputs of the 6008,
Analog Output
Analog outputs........................................2
Output resolution ....................................12 bits
Maximum update rate .............................150 Hz, software-timed
Output range ...........................................0 to +5 V
Output impedance...................................50 Ω
Output current drive................................5 mA
Power-on state ........................................0 V
Slew rate .................................................1 V/μs
Short circuit current ................................50 mA
Absolute accuracy (no load) ...................7 mV typical,
36.4 mV maximum at full scale
So yes you could output a voltage between 0 and 5 Volts. You could only change the voltage level every 10ms or so.
In answer to what your device (pump) requires I don't know.
"So, this got me thinking, do i really need PWM control for the micro-pump (DC motor)?"
Have you got a specification datasheet (website) of the pump? - I dont mind taking a look.
Have you looked in the NI Example Finder to VIs that generate PWM and AnalogOutput (AO?). In the example finder (help>>Find Example) it gives you information on what devices can use the examples - simply look for the ones which say usb6008.
Kind Regards
James Hillman
Applications Engineer 2008 to 2009 National Instruments UK & Ireland
Loughborough University UK - 2006 to 2011
Remember Kudos those who help!

No sound when streaming audio through USB to car stereo *solved*

Short version: Many months ago my wife and I had iPhone 4s with AT&T and my phone would playing streaming apps (Pandora, Slacker) over USB to my Pioneer head unit and my Ford SYNC while my wife's would not. There was no error given, it appeared to be playing fine-- there would just be no sound.
Fast forward to present and I have a Verizon iPhone 4 and I am getting the same issues as my wife was having previously.
After much forum reading about iOS4 breaking this functionality for many people across the globe with many makes and models of stereos and cars I realized I was not getting the same error as all of these people. I was getting NO error at all; I just wasn't getting any sound out of these apps.
I read a post about how a random song would kick on when they connected their phone to the car, then it hit me. My old iPhone used to do that. Then THIS hit me. I do not have any mp3s synced to this phone. Nor did my wife back then. So I threw a handful of songs onto my iPhone and sure enough it immediately chose a song at random, started playing it and then I switched to Slacker radio and it faded down the iPod song and started streaming the audio from Slacker.
tl;dr version: If streaming apps are not playing any sound through your USB cable. Make sure you have some songs synced to your iPhone.

I found a solution, reset all settings. Settings > General > Reset > Reset all Settings
Fixed the problem, now back to properly streaming music!

IPod touch not working through USB in car

Does anyone know how to resolve an issue with the new IPod Touch 4th gen just purchased not working through car stereo. Have a new Toyota camry touring. You can hear sound when connected when you slide to unlock or go into an app the sound goes through the speakers fine but the radio face says loading and won't go any further, if you then try to go to the music screen it says connected so you can't get into the music to try to play. Has anyone else had this problem and resolved it. Not sure if the software of the radio can be upgraded to suit maybe at service?? Not really sure. Any help would be great

Have you contacted your auto dealer? Some users have reported problems with there car systems not worked with the latest iOS. I searched the iPod Touch forum for Toyota but did not find any previous posts concerning Toyota.
Have you tried resetting your iPod:
Press and hold the On/Off Sleep/Wake button and the Home
button at the same time for at least ten seconds, until the Apple logo appears.

Device control through USB

I have a customer that has a kiosk that they want to enhance and modify. The original version was done using a program called LabView which communicates with a DAQ module plugged into the usb port. There are five buttons. The first 4 buttons pump dirty water out of their corresponding containers into a holding talk. The 5th button pumps the dirty water through a filter and into a clean water tank. My question - is there a way to control the motors and servos through the DAQ module using Director?

I found out from one of the company reps that the DAQ Module is controlled by C++ commands, LabView commands, and ActiveX commands. So I should be able to insert an ActiveX control in Director and do it that way.

My ipod touch 5th gen has no sound through usb hookup-car

I Have a kenwood ddx 370 touch screen HU installed in my car, and i can'y get sound from my speakers when its in ipod mode, and the wires are plugged in to the HU. I used to own a iphone 4, and a iphone 4s that both worked. now this issue is strange with not getting sound, as everything else works.
it charges, it is recognized by the HU, displays all the album art song etc, but just not hearing the sound.
my radio, xm radio cd and all that work fine. its strange how the phone does everything on the radio but have sound coming out of speakers. when i just use the aux cable i get the sound, but none from usb/ipod option. anyone familiar with this, and how to fix this?
i just got the ipod touch no even a week ago either, and it was brand new.

Does Kenwood say it will work with a 5G iPod (or iiPhone 5)?
Did the iPhones have iOS 7? Sometimes an iOS update breaks compatibility
Sometimes this works
Try:
- Reset the iOS device. Nothing will be lost
Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Reset all settings
Go to Settings > General > Reset and tap Reset All Settings.
All your preferences and settings are reset. Information (such as contacts and calendars) and media (such as songs and videos) aren’t affected.
- Restore from backup. See:
iOS: Back up and restore your iOS device with iCloud or iTunes
- Restore to factory settings/new iOS device.

Anyone having trouble with operating music controls through the control center?

Sometimes I pause my music to do something else. When I swipe up later to access the control center, I hit the play button, but it won't play. I could hit the button on my headphones to play but still no result. I have to actually open the music app and press play. Is anyone else having this problem?

IslandPrince89 wrote:
That actually helped but it seems that there are a lot of bugs in the iOS 7.0.2 ..
You can use this Link to send your Feedback to Apple
http://www.apple.com/feedback/

Why cannot control iPhone through USB in Honda or Yamaha

My wife and I have two iPhone 5s and two iPads at 8.1.3 that can no longer be controlled when plugged into usb devices such as my 2014 Honda Odyssey and my Yamaha receiver. The song titles appear and I can scroll but will not play the music after clicking using the Honda or Yamaha controller. Only way to play music is through the iphone/ipad. Everything worked fine up until iOS 8. Obviously a pain and safety issue if I can't select songs from my vehicle system and have to resort to looking at the iPhone instead.

Check to see if there is a software update for the Honda. I just got a software update the other day for my Hyundai, although it was working just fine with my phone. I've read of other problems with Honda and the iPhones. It seems what I remember on a couple of threads is they were working on updates. You can search here to see if you can find anything on the threads, but they also seemed to be geared more towards Bluetooth.

HT201401 no music audio through headset when connecting to car or stereo

hello, Im not getting any music audio through the headset when connecting to my car or stereo I can hear iPhone noises though. I'm not having the same problem with iPhone earphones but dont think its lead compatability as both leads have worked fine until yesterday. i have tried updating and resetting my phone and no joy. Any ideas please as this is quite frustrating?

as stated then the ios devices does not support connecting by usb to anything but a computer or the ac charger
it does not work with usb mass stroage driver which devices such as stereos which have usb conenctors rely on
the rest of the smartphones and tablets is quiting that feature too
suppose they all feel the disc mode is too often used for copying media between people without the rights to play it

Ios7 no call decline option when its locked battert drains fast music is not able to controlled through headset unless the music app is open please fix these bugs

Ios7 no call decline option when its locked battert drains fast music is not able to controlled through headset unless the music app is open please fix these bugs

if they are unable to update all languages in a normal time gap (it is now 6 months ago they released firmware 4.22 for the first product code (actually mine and maybe a few others)), they should not offer those many versions. the huge bug with out of memory in nokia navigator with firmware 3.58 is not fixed yet for those people. really absolutely not acceptable.
besides that, currently my phone is in a nokia service center, microphone doesnt work anymore (the one who i call just hears a very loud noise). my brother got the same phone, his one is in nokia service center since 2 weeks now, because it doesnt charge anymore as there seems to be a connection broken inside the phone).
well that will be fun if the phone returns (approximately 4 weeks), as I guess the phones will have new IMEIs as they will send 2 new phones and not fix the problem (would cost them more). but as i got a western europe with nordics-map licence locked to the imei, the next problem will be there after I get a nokia 6110navi with another IMEI back. i get really upset with this really slow support.

Iphone 5 stopped charging and playing music through usb in my 2012 Chevy sonic after iOS 8.1 update. Several friends have same problem. Hard reset didn't help. Help???

Iphone 5 stopped charging and playing music through usb in my 2012 Chevy sonic after iOS 8.1 update. Several friends have same problem. Hard reset didn't help. Help???

Fixed it. It is on Chevrolet's end. Press config to access the configuration settings. Turn menu/tune knob to highlight vehicle settings. Press menu/tune to select the vehicle settings menu. Choose return to factory settings.

DC motor closed loop control through labview using usb 6008

Hello
i am doing a project in which i want to control the speed of a DC motor (PID control) through labVIEW 2010. I am having a DC motor, a drive unit that regulates the voltage to the motor by getting analog voltage from 0 to 3.3V ( it can be used for both directions) and i also have a NI usb 6008 board. The problem is that i can't feed the usb 6008 with the digital signal from my hall effect speed sensor. Is it posible with this setup to control the motor?? I can also try to use the pulse as analog input and trasform the frequency into rpm's. Then i am thinking of generating an analog signal to feed the motor drive. If you have any further suggestion of a probably better hardware setup would be more than helpfull to me.
Sincerely
Jason Chaloulos

Hello Michael
Thanks for the reply. I came across those topics before and all of them are trying to generate a PWM signal as output i want to use just an analog signal output so timing on the output is not that important i guess. i am struggling on getting the frequency from the digital input signal that my hall effect sensor generates. Since the maximum speed of the motor is 3000 rpm and with my tooth wheel the maximum output frequency of the sensor will be 300Hz which i see its way less than the limitation of my ni board. Is there any tutorial documentation that might help me with this one ? Thank you in advance.
Kind regards
Jason

HT1386 i updated itunes 11.1 yesterday and now im trying to get my music on itunes to sync onto my iphone 4s but when i connect it through usb...Itunes is saying " waiting for changes to be applied"?

i updated itunes 11.1 yesterday and now im trying to get my music on itunes to sync onto my iphone 4s but when i connect it through usb...Itunes is saying " waiting for changes to be applied"? so i dont know what to do cause i just want to sync my music from itunes to my iphone 4s

I had the same problem and the fix was so easy that I felt a little silly after spending 2 hours with an Apple Technician. At the end of it all, what I had to do was make sure ALL music was deleted from my iPhone 5 by going into usage and clearing out the music folder. All I had to do then was turn my phone off and turn it back on again. I had not done this after my phone upgraded to the new 7.0 IOS. What's the first thing you do when experiencing computer problems? Reboot! It fixed my problem and now my iPhone 5 synchs perfectly when I had it connected to my computer. I am also on iTunes version 11.1.

Iphone 4G music plays through bluetooth, but only one speaker works in my car when i play it, why is that?

This problem suddenly started about a week ago. i had both speakers working, then after i updated my phone one skeaker stopped working on the driverside like with a pair of headphones when the left headphone stops working. only thing is i don't have to physically plug in my phone to listen to music, i use bluetooth, my car came with the option. i was wondering if its because the balance got changed in my phone some how or if its something else. please help!

for troubleshooting I would try another bluetooth device to make 100% sure that it was an iphone issue

When connected to my Ford Mondeo, my ipod nano can be controlled through interface. But after while it comes up with message 'loading data' and then freezes. Anyone else got the issue?

When connected to my new Ford Mondeo, my ipod nano can be controlled through user interface in car. This worksd most of the time, but after a while if I try to change the music or search, it comes up with message 'Loading Data'. I then have to pull out USB and reinseert, at which point it works again. Has anyone esle expereinced this/have a solution?

Does not matter if anyone else has this issue. You need to contact the Ford dealership. It's their product you are having problems with.
If you really want to know if anyone else has this issue, post on Ford's Mondeo message boards. It's where the Ford car owners hang out.

IOS8 music control through usb in car (Jeep & Volvo)

Similar Messages

Maybe you are looking for