Ipad is showing connected to wifi but it is saying its not connected to internet.  I have reset all settings, tried to change IP address and subnet mask and nothing is working.

My ipad mini 3 is not showing that it is connected to the wifi, but it is saying it is not connected to the internet.  I have reset network settings and then reset all settings and it has not worked.  I have tried to change it to static and change the IP address and the subnet mask and that is not working either.  I have also tried to use the wifi in different places and that doesn't work either.  Please help!!!!  iPad is useless without the internet.

1. Set router back to Auto DHCP.
2. Turn off router for 30 seconds and on again.
3. Re-boot iPad.

Similar Messages

  • My itouch is connected to my wifi, but it tells me its not connected to the internet, whats wrong?

    my itouch picks up me wifi, but when i try and use safari it tells me its not connected to the internet, it worked the other day but doesnt now whats wrong?

    - Reset the iPod:
    Reset iPod touch:  Press and hold the On/Off Sleep/Wake button and the Home
    button at the same time for at least ten seconds, until the Apple logo appears.
    - Power off and then back on your router
    - Reset network settings: Settings>Genera>Reset>Reset Network Settings
    - The troubleshooting here:
    iPhone and iPod touch: Troubleshooting Wi-Fi networks and connections

  • I installed an Extreme in place of an old Express, the various phones and Ipads seem to work on the WiFi but the Mac itself will not connect.  It says something about the IP address.

    I installed an Extreme in place of an old Express, the various phones and Ipads seem to work on the WiFi but the Mac itself will not connect.  It says something about the IP address being used by another device.  Second wifi network was also created.  The Mac worked for a few minutes and then gaev up citing eth IP problem......any clues people??

    If you have not already done so, now would be a good time to perform a complete network power cycle.......to give everything a fresh start.
    Power off every device on the network.....computers, printers, hard drives, etc......in any order that you want
    Wait a full minute
    Start the modem, and let it run by itself for 2-3 minutes
    Start the next device connected to the modem and let it run a full minute
    Keep starting devices one at a time about a minute apart until the entire network is back up
    Check the network

  • HT1212 IPAD is Disabled, tried to connect via itunes but get error "iTunes could not connect to the [device] because it is locked with a passcode. You must enter your passcode on the [device] before it can be used with iTunes."

    IPAD is Disabled, tried to connect via itunes but get error "iTunes could not connect to the [device] because it is locked with a passcode. You must enter your passcode on the [device] before it can be used with iTunes."

    iOS: Device disabled after entering wrong passcode
    http://support.apple.com/kb/ht1212
    How can I unlock my iPad if I forgot the passcode?
    http://tinyurl.com/7ndy8tb
    Using iPhone/iPad Recovery Mode
    http://ipod.about.com/od/iphonetroubleshooting/a/Iphone-Recovery-Mode.htm
    Saw this solution on another post about an iPad in a school enviroment. Might work on your iPad so you won't lose everything.
    ~~~~~~~~~~~~~
    ‘iPad is disabled’ fix without resetting using iTunes
    Today I met my match with an iPad that had a passcode entered too many times, resulting in it displaying the message ‘iPad is disabled – Connect to iTunes’. This was a student iPad and since they use Notability for most of their work there was a chance that her files were not all backed up to the cloud. I really wanted to just re-activate the iPad instead of totally resetting it back to our default image.
    I reached out to my PLN on Twitter and had some help from a few people through retweets and a couple of clarification tweets. I love that so many are willing to help out so quickly. Through this I also learned that I look like Lt. Riker from Star Trek (thanks @FillineMachine).
    Through some trial and error (and a little sheer luck), I was able to reactivate the iPad without loosing any data. Note, this will only work on the computer it last synced with. Here’s how:
    1. Configurator is useless in reactivating a locked iPad. You will only be able to completely reformat the iPad using Configurator. If that’s ok with you, go for it – otherwise don’t waste your time trying to figure it out.
    2. Open iTunes with the iPad disconnected.
    3. Connect the iPad to the computer and wait for it to show up in the devices section in iTunes.
    4. Click on the iPad name when it appears and you will be given the option to restore a backup or setup as a new iPad (since it is locked).
    5. Click ‘Setup as new iPad’ and then click restore.
    6. The iPad will start backing up before it does the full restore and sync. CANCEL THE BACKUP IMMEDIATELY. You do this by clicking the small x in the status window in iTunes.
    7. When the backup cancels, it immediately starts syncing – cancel this as well using the same small x in the iTunes status window.
    8. The first stage in the restore process unlocks the iPad, you are basically just cancelling out the restore process as soon as it reactivates the iPad.
    If done correctly, you will experience no data loss and the result will be a reactivated iPad. I have now tried this with about 5 iPads that were locked identically by students and each time it worked like a charm.
    ~~~~~~~~~~~~~
    Try it and good luck. You have nothing more to lose if it doesn't work for you.
     Cheers, Tom

  • Connected to wifi but App Store says I'm not connected

    Connected to wifi but App Store says I'm not connected so cannot update my apps

         Power cycle
         Power off the router. Unplug it from the wall. Wait a while.
         Plug it back to the wall. Power the router on. Wait until all the lights are lit properly.
         It will take a   while.
         Restart the computer.
         Start up in Safe Mode
         http://support.apple.com/kb/PH11212

  • Tried to use iphone connecting to wifi but failed dispite password correct, cable connection ok, and even reset network setting in iphone. Anyone can help? KC

    Tried to use iphone connecting to wifi but failed dispite password correct, cable connection ok, and even reset network setting in iphone. Anyone can help?
    Kin Chi

    I get in now with the following procedures taken:
    1. Reset network as suggested in Apple app.
    2. In the wifi connection, instead click in the user name as shown in the screen, I click Others and re-type the user name as appeared before. In the security, instead of none, I click WEP. It will then prompt you to put in password. I then put in password as I know for that user name again.
    Then, it joined the wifi..
    Hope this can help someone who get this problem.
    Kin Chi

  • My phone won't update it keeps saying its not connected to the Internet and it is. And now my apps won't work?? Help

    MY phone needs updating and it won't let me. It keeps saying its not connected to the Internet and i

    Temporarily disable any security software on the computer.

  • My camera doesn't work, it says its not connected.

    Hi, i got a macbook air, and its been a while since my camera doesnt work,
    its says its not connected.

    What kind of external camera is this? I am assuming it is a USB camera? Make sure that you aren't using any USB hubs. Also try connecting it to another USB port. Have you installed the drivers from the camera manufacturer yet?
    Thanks,
    Sean
    -------------How do I give Kudos? | How do I mark a post as Solved? --------------------------------------------------------

  • I want to download os x mavericks but it is saying its not compatible. my laptop is on the list of compatible laptops.

    i want to download os x mavericks but it is saying its not compatible. my laptop is on the list of compatible laptops.

    Do  you meet all requirements:
    Upgrading to Mavericks
    You can upgrade to Mavericks from Lion or directly from Snow Leopard. Mavericks can be downloaded from the Mac App Store for FREE.
    Upgrading to Mavericks
    To upgrade to Mavericks you must have Snow Leopard 10.6.8 or Lion installed. Download Mavericks from the App Store. Sign in using your Apple ID. Mavericks is free. The file is quite large, over 5 GBs, so allow some time to download. It would be preferable to use Ethernet because it is nearly four times faster than wireless.
        OS X Mavericks- System Requirements
          Macs that can be upgraded to OS X Mavericks
             1. iMac (Mid 2007 or newer) - Model Identifier 7,1 or later
             2. MacBook (Late 2008 Aluminum, or Early 2009 or newer) - Model Identifier 5,1 or later
             3. MacBook Pro (Mid/Late 2007 or newer) - Model Identifier 3,1 or later
             4. MacBook Air (Late 2008 or newer) - Model Identifier 2,1 or later
             5. Mac mini (Early 2009 or newer) - Model Identifier 3,1 or later
             6. Mac Pro (Early 2008 or newer) - Model Identifier 3,1 or later
             7. Xserve (Early 2009) - Model Identifier 3,1 or later
    To find the model identifier open System Profiler in the Utilities folder. It's displayed in the panel on the right.
         Are my applications compatible?
             See App Compatibility Table - RoaringApps.

  • My ipod touch 4th generation says its connected to wifi but whenever i try to use wifi it says its not connected

    I have had my ipod touch 4th generation for a few years now and all of a sudden it wont connect to wifi. Even though it says im connected it doesn't work. It has a tick beside the name and everything! Also it has three bars saying im fully connected but whenever i go onto an app that requires wifi it says im not connected. I have reset my ipod, reset the settings, forgot the network then connected again, everything!!!! No matter what i cant get wifi for anything that i need it for.
    Please, Please, Please, Please can someone give me an answer that will work and if you do answer please tell me what an router is because everyones talking about it and i don't know what it is??!!!  
    PLEASE

    Does the iPod connect to other networks?
    Does the iPod see the network?
    Any error messages?
    Do other devices now connect?
    Did the iPod connect before?
    Try the following to rule out a software problem:                 
    - Reset the iOS device. Nothing will be lost
    Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
    least ten seconds, until the Apple logo appears.
    - Power off and then back on the router
    - Reset network settings: Settings>General>Reset>Reset Network Settings
    - iOS: Troubleshooting Wi-Fi networks and connections
    - Wi-Fi: Unable to connect to an 802.11n Wi-Fi network
    - iOS: Recommended settings for Wi-Fi routers and access points
    - Restore from backup. See:
    iOS: How to back up
    - Restore to factory settings/new iOS device.
    If still problem make an appointment at the Genius Bar of an Apple store since it appears you have a hardware problem.
    Apple Retail Store - Genius Bar

  • Ipad wifi is connected but when i try to use the internect it says its not connected to internet but shows connection

    I connect on my ipad to my wifi and it sows good signal strength but when i try using the internet it says it cannot because it is not connected to the internet.

    Have you tried rebooting your router - unplug it for about 30 seconds and then plug it back in? Is this a new problem? Have you been able to connect to your home WiFi before?
    This WiFi assistant set up article might help.
    http://www.apple.com/support/ipad/assistant/wifi/
    More troubleshooting help is available here.
    http://support.apple.com/kb/ts1398

  • One ipadmini will connect to WiFi but an identical one will not.  Any suggestions?

    Of 2 identical ipadminis, one will connect to the WiFi network but the other one receives the error message: Unable to join the network "XXXX".  Any suggestions?

    Hi thekps. Sorry to hear about your problem. Usually when an iPad can't connect to WiFi, it is usually the WiFi/Modems fault. I'm not saying its broken as such. There are many occurrences to your problem.
    You are to far from the modem
    You are typing in the wrong network key in
    There are too many devices attached to the modem
    Here's a little trick that I like to use:
    Go to Settings and click on WiFi. Press Other. Type in your SSID/ Network Name. Select your modems security type. If you dont know this, youll have to guess a lot. Then type in your password. If that doesn't work let me know!

  • HT5642 My iPad mini is not updating as it says its not connected to the Internet yet clearly I am

    My iPad mini is not updating the operating system, when I try a message pops up saying I'm not connected to the Internet. I have full signal on my wifi and have been able to update any aps I have and clearly I have Internet service. How do I resolve this issue?

    Try This...
    Close All Open Apps...  Perform a Reset... Try again...
    Reset  ( No Data will be Lost )
    Press and hold the Sleep/Wake button and the Home button at the same time for at least ten seconds, until the Apple logo appears. Release the Buttons.
    http://support.apple.com/kb/ht1430
    If necessary...
    Connect to iTunes on the computer you usually Sync with and “ Check for Updates “...
    See the Using iTunes Section Here...
    How to update your iPhone, iPad, or iPod touch
    Make sure you have the Latest Version of iTunes Installed on your computer ( v 11.1)
    iTunes free download from www.itunes.com/download
    Note:
    It is both Prudent and Recommended to Backup Before any Major Update or Upgrade.
    How to BackUp
    http://support.apple.com/kb/ht1766
    What gets Backed Up
    iTunes http://support.apple.com/kb/ht4946
    iCloud http://support.apple.com/kb/PH2584

  • Ipod can charge but itunes says its not connected

    Just got a ipod about an hour ago and connected it to my cpu and it is charging but when i try to put songs from my cpu to the ipod its doesnt show up anywhere i cant sync it and i did the diagnostics check and it says Ipod connection status failed. How do i fix it. I went to the help menu and none of it has resloved my problem.

    First of all, try another port on your computer. Some ports are not connected direct to the motherboard and do not recognize the iPod as well as those that are. Reset the iPod each time you connect it to another port.
    Then try with the iPod in forced disk mode.
    Putting iPod into disk mode.
    Still no joy, see these.
    USB drivers are not installed properly.
    iTunes 7 doesn't recognize the iPod.

  • My gmail keeps saying its not connected on my Blackberry Z10

    Recently thegmail on my Z10 has stopped the gmail connection - it does not allow emails through and when I check the systems button it tells me that gmail is not connected . sometimes it says there is no internet access when there is , other times it does not give any reason. 
    I tried turning the phone off and on and occasionally it starts working but not often. It seems worse than ever now since I downloaded the Blackberry update to my phone yeaterday.
    Please help because if I cannot access my emails the Blackberry is not fit for purpose.

    Hello
    With a strong carrier network signal (e.g., not merely WiFi), I suggest the following steps, in order, even if they seem redundant to what you have already tried (steps 1 and 2 each should result in a message coming to your BB...please wait for that before proceeding to the next step):
    1) Register HRT
    KB00510 How to register a BlackBerry smartphone with the wireless network
    Please wait for one "registration" message to arrive to your Messages app (or otherwise be notified)
    2) Reboot
    Pre-BB10 Devices ONLY. With power ON, remove the back cover and pull out the battery. Wait about a minute then replace the battery and cover. Power up and wait patiently through the long reboot -- ~5 minutes.
    BB10 Devices. Hold the top button down until the counter reaches zero. Wait for the device to be fully shut down (e.g., nothing at all displayed on the screen, no LED lights, etc.). Hold the top button until the red LED is lit. Wait through the full boot-up process. IF this fails, you can attempt the battery-pull method above, but it is normally NOT recommended unless nothing else works.
    See if things have returned to good operation. Like all computing devices, BB's suffer from memory leaks and such...with a hard reboot being the best cure.
    Hopefully that will get things going again for you! If not, then you should try deleting and re-adding your configurations for the affected email accounts. Otherwise, you should contact your mobile service provider for formal support.
    Good luck!
    Occam's Razor nearly always applies when troubleshooting technology issues!
    If anyone has been helpful to you, please show your appreciation by clicking the button inside of their post. Please click here and read, along with the threads to which it links, for helpful information to guide you as you proceed. I always recommend that you treat your BlackBerry like any other computing device, including using a regular backup schedule...click here for an article with instructions.
    Join our BBM Channels
    BSCF General Channel
    PIN: C0001B7B4   Display/Scan Bar Code
    Knowledge Base Updates
    PIN: C0005A9AA   Display/Scan Bar Code

Maybe you are looking for

  • Internal table in routine of infocube

    Hi Plz can anybody let me know simple scenario for where we use the internal table in the routine IN BW SIDE. Let me say i have 3 characteristic like CID,PID AND SRID and keyfigures like qty , revenue and amount. Thanx & Regards, RaviCHandra Please s

  • HP Photosmart 7510 won't scan

    Hello!  I have an HP Photosmart 7510 all-in-one.  I've had it for over a year now, and have never had a problem until recently.  It has always printed and scanned just fine.  Now I can't get it to scan at all, although it still prints without a probl

  • Adobe Acrobat XI crashing when opening PDFs in Yosemite

    I am having a problem with Acrobat XI Pro continually crashing when I open PDF files stored on my hard drive.  The documents will then open, and Acrobat will behave normally for a bit, and then, the next time I try to open a PDF, the program crashes.

  • Block based on stored procedure

    I need to create a matrix-like form. I think one option is to base the block on a stored procedure. The idea is to create a PL/SQL Table based on a PL/SQL record of (x)number of colums. My problem is to access each column without using the (.)notatio

  • I need to fix my plug in container it is using 62% off my cpu. V.4 Firefox on Vista Basic

    Vista Basic Norton optimizer showing the plug in container is using 62% of my cpu capacity. As a result everything is slow loading. Just upgrade from 3.6 Firefox.