IPCC and CVP in VMWare, same as Call Manager

Hi All;
As I know that new version of Cisco Call Manager (version 8) is working based on VMWare (and it is must), so I am asking if there is a versions for IPCC and CVP working on VMWare (this for production and not for LAB).
Appreciate kindly help and support.
Regards
Bilal

UCCE 8 on VMware 4.0 on the Cisco UCS hardware only.
But in a lab environment, many (most) of us are using VMware in some shape or form.
I have 5 x HP DL380G5 2 CPU servers each with 6GB in a rack running ESX 3.5, with a smaller server for the Virtual Center software. Each ESX host can support 7 virtual machines - DC, Rogger, AW/HDS, PG, CVP7, CUCM and CUPS. You do need a lot of disc space though - especially CUPS (80GB) and CUCM (40GB). And you need a lot of extra space for snapshots.
Regards,
Geoff

Similar Messages

NIC config of VMware installation of Call Manager

System version: 8.6.2.22900-9
VMware Installation: 1 vCPU Intel(R) Xeon(R) CPU E5-2609 0 @ 2.40GHz, disk 1: 80Gbytes, 4096Mbytes RAM
A few month ago we had a vendor come in and upgrade our old VOIP system with a VMware solution of Call Manager. Versions are shown above.
I use Veeam to backup these VM's and it was taking hours to finsih so I starting digging into VCenter to look at the netwroking setup.
Even though the server has gigabit ethernet cards they "hard coded" the speed down to 100 Meg and changed the duplex to half.
Does anyone know of any reason why they might have done that? Will it fail if I change the speed to GB and utilze full duplex?
thanks...

Joe...
Questions and a comments
Questions in the post above you mention...
"At this point, I would probably try the Hypervisor and Switchport hardcoded at 1000/Full to match CUCM. Check interface counters and watch for errors and runts."
When you refer to "Switchport" I am assuming you are you talking about the physical port on our physical switch?
which is interesting becasue I just looked only to discover that on our physical cisco switch (Catalyst 4506) that our phone system is physcally plugged into our 10/100 module and not into our gig module. So even if I made all of those changes I still would have been at a 100 MPs speed becasue of the physical connection to our switch. So obviously... I would need to change ports on the physical switch to the gig module, correct?
question 2...
monitoring the ports for errors and runts, again I am assuming you are talking about the physical Cat 4506 switch?
Assuming then I move the connections into gig ports 5/26 & 5/28, etc...
From a telnet session into physical switch... after enable mode type...
switch#show int gigeth5/26
and I will see stats from that interface correct? or do you look for these in a different mannor?
comments... first of all, thank you....
second....
I am not sure I quite understand anything about you very last post.... about the restricted UC and Cisco support..
yes, I am running USC C220 M3 servers... are you saying that if I have over 1000 users that TAC will not support performance issue? I ask becasue we only have about 125 users....

Ringtones and background images not available after call manager upgrade

Hi,
We have upgraded our call manager from version 8.5 to 10.5. Once after the upgrade we lost all the Ringtones and background images except the two default ringtone and background images. we got 8945 sccp phones(running 9-3-1 firmware) and 9951 sip phones(running 9-4-1 firmware). Both these phones lost these list. However the ringlist.xml is available in the tftp server with all the ringtones and the phones are pointed to the right tftp servers. I tried to restart the tftp servers and tried again, however that didn't help. we are using call manager 10.5 and h323 voice gateway. Could anyone please help on this.
Thanks
Barry

Hi Tony,
I can see the ringtone files in the call manager (osadmin>tftp file mgmt), i have also restarted the tftp services, but it didn't help. I believe you advised to re-upload the ringlist file (Ringlist.xml) and try again. I will try this and update you. Please let me know if you have any other suggestions.
Thanks
Barry

Remove device and profile from call manager

Is there any documentation on how to remove phones and EM, RDP, CSF profiles from call manager in order to free up some licensing??

EM does not take any licenses, but the way you want to do this (assuming all associations are correct and dependencies would prevent you from doing it anyway):
delete UDP
delete CSF device
delete RDP
delete desk phone

Advanced Call Manager and my E71x not getting alon...

I just bought a E71x and decided to give the advanced call manager a try. Found my phone on the Nokia website, noticed that it was listed FOR MY PHONE and figured, "Eh why not. Sounds cool enough." Installed it onto my phone through PC Suite no problem. Then went to run it on my phone and........ locked up after informing me it was a 30 call trial and asked me if I wanted to try or buy. I click try... nothing. I click buy.... nothing. Anyone got any suggestions?? Have since uninstalled the program.

you can contact nokia care line or use the 'contact us' button on the top right of this page. now i don't know if this is a nokia app. if it is not then i suggest you contact the developer directly and tell them what issues you are having. i know that you got it from the nokia site but it could have been some other company and nokia just posted a collection of apps for your phone. here are the links that you can use to contact nokia :
/discussions/board/message?board.id=topfaq&thread.id=3
hope you get it sorted out
You know what I love about you the most, the fact that you are not me ! In love with technology and all that it can offer. Join me in discovery....

Cisco Call Manager Administration Page Drop down menu not working

I'm running the mobile app browser on my Xoom tablet and when I log into Cisco Call Manager Administration page I get the menu's but it will not pull down the options. The same issue happens in google chrome. I use your browser on my desktop and have no issues logging into Cisco Call Manager Administration page and getting the drop down menu's to appear but the mobile version of your browser is not working. Is there a work around? I tried changing the UAString to Desktop, iPad etc and the issue is still there.

Thanks but I've tried all that. It happens in Chrome also. I've tried Opera and it works on that. I've read other forums and it looks like a Java script issue that Chrome and now Firefox Mobile cannot seem to resolve. My preference is Firefox and I'm sure as more tablets get out then this will be solved at some point. I just don't know how it is prioritized. I do know that in order for Androids to be viable in the business sector they need to address issues like these with a higher priority.

Aging out user profiles in Call Manager

If a user profile is deleted in AD what is the length of time before that user is “aged out” / removed from the CUCM and CUC user DB?
Is there a difference between how it works in 4.1 with Cisco Customer Directory Configuration Plug In vs. LDAP Synchronization in later version?
My understanding is that in 4.1 the Plug In extends AD database to Call Manager and it is not embedded in Call Manager as it is in 5.0 and later. Not sure how that plays on removing users from CUCM through synchronization.
Additionally, my understanding is when a user profile is removed from AD, it gets flagged during Synchronization and that could take a minimum of 6 hours after sync for the user profile to be removed in CUCM or whatever the synchronization is scheduled to.

Oli,
It all depends on your sync frequency. If you remove users from AD, CUCM will mark them as "delete pending".
CUCM garbage collector will rip these out 24 hrs later.
http://www.cisco.com/en/US/products/sw/voicesw/ps556/products_configuration_example09186a0080a57c4c.shtml
Every night at 3.15 am, an internal process called the Garbage Collector service runs. This process permanently deletes any account that has been in the
Inactive – Delete Pending state for over 24 hours. The Cisco Unified Communications Manager does not sync Active Directory passwords. Cisco Unified Communications Manager has no knowledge of Microsoft Active Directory encryption mechanism. Instead, in Cisco Unified Communications Manager 5.0, a default password of ciscociscoand a default PIN of 12345are assigned.
cheers
=============================
Please remember to rate useful posts, by clicking on the stars below.
=============================

Nortel Call CS 1000 / Cisco Call Manager

I know kind of a oxymoron, but currently tenants are to be only on Nortel. Now no other phone and this one in particular is having problems. But one is given to the manager to have Voicemail. But because nobody (including me) has any knowledge of Nortel except Cisco CUCM, a outsource tech directed the phone to be sent to the Call Manager(Cisco) as the rest of the city employees is on Cisco. Now it is not working and instead its going to 5117 when he goes to voicemail and not 1900 which is through Cisco Call Manager.
All I want is to get this Nortel phone and have it sent to the Call Manager (Ext 1900). I am using the web GUI so how do I get this done?
This topic first appeared in the Spiceworks Community

Hi!
Just for curiosity; why wouldn´t you install COP addon?

Cisco Unified Call Studio 8.0 and above with VMWare image?

There is no official Cisco document which says "CallStudio" can run on VMware environment. However when the licensing was based on SystemID till 7.0 release, we have seen Cisco installing them in couple of customer "demo" location under VMware in region. Version 8.0 and above, the licensing mechanism for Call Studio uses a new FlexLM-based [IPlocking] license. None of the official documents like release notes /installation and upgrade guide / hardware configuration guide doesn't specify support of VM Ware support for Call Studio. Would installing Call Studio in VM Ware image would work above 8.0 with the new licensing in place and is it officially supported by Cisco?
Thanks!
-Sethu

Studio 8.0 installs on XP and Vista. Studio 8.5 installs on Windows 7, Vista, XP.
There are no real performance issues that Cisco could object to if the above operating systems were "guest O/S" on a VMware ESX server - it's not the same situation as the CVP servers, where they do have firm guidelines.
Studio works in this environment and I have customers who run Studio on a "guest O/S" - Cisco did not say specifically that this would be an issue.
But I don't have any documents that confirm that this is OK.
Regards,
Geoff

Iphone 5 issues after IOS 8.2 update: my husband's phone and my phone get the same phone calls ONLY when we are home. Any suggestions on where to look to fix this?

Iphone 5 issues after IOS 8.2 update: all the iphones in the house receive the same phone calls ONLY while we are at home. Any ideas on how to fix this?

That is a new "feature" described in Connect your iPhone, iPad, and iPod touch using Continuity
You can turn it off by going to Settings > FaceTime and changing "iPhone Cellular Calls" to off

My daughter and I share the same apple ID. I am getting her text messages andphone calls. How do I stop that?

my daughter and I share the same apple ID. I am getting her text messages and her phone calls on my phone. How do I stop that?

Get your daughter her own Apple ID.

Iam using iphone 4s and Iphone 5s with same apple ID but my network is different and whenever Iam getting call in i5s and in my both handset same calls are coming. Please provide me solutions

Iam using iphone 4s and Iphone 5s with same apple ID but my network is different and whenever Iam getting call in i5s and in my both handset same calls are coming. Please provide me solutions

On both devices, go to Settings>Facetime and turn off cellular calls.
~Lyssa

My family and I share the same account of apple. I'm getting phone calls and messages from my mothers and my number and vice versa. is there anything we can do

my family and I share the same account of apple. I'm getting phone calls and messages from my mothers and my number and vice versa. is there anything we can do

The short solution is to go to Settings > FaceTime > iPhone Cellular Calls OFF.
However, as Csound points out, you should not really be sharing an Apple ID with anyone. See: How to Stop Sharing an Apple ID.
(Note that I am affiliated with that site, and some pages contain ads).

My dad and i use the same apple id, when he recieves a call, hes phone and my phone ring at the same time, why?

my dad and i use the same apple id, when he recieves a call, hes phone and my phone ring at the same time, why? and how do i fix this

Settings > FaceTime > iPhone Cellular Calls > OFF

My husband and I shared the same apple id I accidentally deleted his number from the iCloud And now his phone won't receive phone calls or text what do I do

My husband and I shared the same apple id I accidentally deleted his number from the iCloud And now his phone won't receive phone calls or text what do I do

In preferences turn on iTunes sharing in iTunes preferences and keep iTunes turned on in both accounts. Or better yet put the iTunes library on the main HD rather than in an account and set the location of the library to that location in iTunes preferences.

IPCC and CVP in VMWare, same as Call Manager

Similar Messages

Maybe you are looking for