IPhone website is PAINFULLY slow !

Is anyone else experiencing this? This message board area runs fine but mose of Apple's main website is really slow.

Yes, I would schedule a visit to Regent Street's Apple Store Genius Bar for some quick testing and advice.
Before that you might want to try rebooting your router and/or disabling 802.11 b, leaving only g broadcasting. That solved my home connection problems between my iPhone 3G and my Netgear DG834G (connection was very slow and dropping every couple of minutes). Funny enough my iPhone 2G never had any problems connecting to the same Netgear, be it in b/g or just g .

Similar Messages

One secure website loads painfully slow (7 minutes !). Only this site. How can I streamline firefox to load these pages faster?

one secure website loads painfully slow (7 minutes !). Only this site. How can I streamline firefox to load these pages faster? This started happening only after I switched from McAffee to Norton Security Suite. Other secure sites load just fine.
== URL of affected sites ==
http://www.chase.com

If you close Firefox, then start Firefox in Safe Mode, does the problem still occur? For instructions on starting in Safe Mode, see [[Safe Mode]].

ITunes 9.2.1 iPad painfully slow, iPhone 4 fine

Ever since I updated to version 9.2.1 the backup time for my iPad is painfully slow.
I ran a backup on my iPhone4 and it took about 5 minutes for a full backup and sync. So I ran downstairs, grabbed an adult beverage from the fridge, started working on my mac mini. After 60 minutes I went to grab some info off the iPad and it's still backing up an hour later.
System:
iPhone & iPad sync to a Windows 7 PC.
(Trust me if i could migrate without having to wipe my phone and iPad settings they would be on the mac mini)
I've rebooted my PC and iPad several times with no luck.
This has been running perfectly fine with iTunes 9.2.

Requirements to install iOS 4.2.1, this is from http://support.apple.com/kb/DL1061
System Requirements
* Mac or PC computer with USB 2.0 port
* iTunes 10.1 or later
Requirements for iTunes 10.1 on a Mac (this is from http://www.apple.com/itunes/download/ )
Macintosh Hardware
* Mac computer with an Intel, PowerPC G5 or G4 processor
* Intel, PowerPC G5 or 1.0GHz PowerPC G4 or faster processor is required to play Standard Definition video from the iTunes Store
* 2.0GHz Intel Core 2 Duo or faster processor is required to play HD video, an iTunes LP, or iTunes Extras from the iTunes Store
* 512MB of RAM; 1GB is required to play HD video, an iTunes LP, or iTunes Extras
* Screen resolution of 1024x768 or greater; 1280x800 or greater is required to play an iTunes LP or iTunes Extras
* Playing videos also requires at least 16MB of video RAM
* Broadband Internet connection to use the iTunes Store
* Apple combo drive or SuperDrive to create audio, MP3, or back-up CDs; some non-Apple CD-RW recorders may also work.
* Apple SuperDrive to back up your library to DVDs; some non-Apple DVD-RW drives may also work.
Macintosh Software
* Mac OS X version 10.5 or later
* QuickTime 7.6 or later
* Support for HE-AAC requires QuickTime 7.6.4 or later
* Safari 4.0.3 or later
* 200MB of available disk space

Syncing songs painfully slow on an iphone 6 running the latest software.

Hello there,
I've been having problems syncing my tracks to spotify on my iPhone 6. It's painfully slow in that just to sync 18 tracks, the phone has to time out at least 5 times to "pause track syncing because i've been inactive for too long".
Is anyone else having this problem on the iphone 6?
Thanks:)

To sync, the Spotify app needs to stay open, otherwise it will stop syncing in the background. This is due to Apple's background activity restrictions.
The best way is to go into the iPhone settings:
Settings --> General --> Auto Lock --> Set it to "NEVER"
Now leave the Spotify app open on your iPhone and let it sit on a table plugged in to charge
When you are done, make sure to turn "Auto Lock" back to your preferred setting.

3g mobile data on iPhone 4s painfully slow to non existent

I get a very painfully slow connection accessing the web from outside of my home?

hi ProfessorPhone
As you are asking for some detailed information, I'm flagging your post with our Mobile Tech Team, but as they don't work weekends, you won't receive a response until Monday.
Regards

Painfully slow access to admin console (how can I fix it?)

Hi,
I'm using using Sun Java System Web Server Version 7.0U4 B12/02/2008 02:17 running on CentOS (Redhat EL) release 4.4.
The problem is that using the Admin Console (on port 8989) is painfully slow. It takes minutes for each page to load, but they do usually load.
Any ideas on how to fix that?
There are some other things going on that might be related and helpful to know:
I get certificate errors when I access the Admin Console (e..g, IE complains about a mismatched address). I've tried following the directions to install the certificate in IE7 and FF3, but neither has stopped bothering me about the certificate error.
I have the server behind a firewall which allows all outgoing traffic and select incoming ports to the server. The firewall also maps a public IP address to the server's local IP address (e..g, 10.10.10.8).
If I access the Admin Console locally via the LAN address (https://10.10.10.8:8989) it is no longer slow, but I get booted back to the login screen very frequently (e.g, every minute or two of casual browsing through the console), and I still get the certificate error
We haven't given the server a name, but access it by IP address, and the virtual server configuration in the Admin Console is name "localhost.localdomain"
Any help and suggestions would be greatly appreciated!! I've tried searching for solutions several times, but haven't succeeded.
Thanks,
Tim

Thanks for the thoughts
sriram.natarajan wrote:
The problem is that using the Admin Console (on port 8989) is painfully slow. It takes minutes for each page to load, but they do usually load.
Any ideas on how to fix that?
sounds more like some network issues. are you running your browser on your centos 4.4 as well ? also, did you try to connect using your IP - some thing like https://<ip>:8989 ?
No, we're not running the browser on centos 4.4. We're runing browsers on laptops, connecting both offsite via public IP address and in the office via both the public IP address and the LAN ip address.
Yes, we're using the ip address as you demonstrated. This machine does not have a domain name attached, so we only connect via ip addresses (mapped public or LAN)
>>
I get certificate errors when I access the Admin Console (e..g, IE complains about a mismatched address). I've tried following the directions to install the certificate in IE7 and FF3, but neither has stopped bothering me about the certificate error.it is not a certificate error. web server 7 admin server uses a self signed certificate . this is necessary step. however, IE reports a warning when it sees a self signed certificate. it wants you to know that it does not understand who sent this certificate. you need to create an exception - saying that you know what you are doing then there won't be any certificate error ..Okay, I'll look for how to do that, but so far I've only found instructions for how to install the certificate in the browsers, and unfortunately, that hasn't made a difference.
>>
I have the server behind a firewall which allows all outgoing traffic and select incoming ports to the server. The firewall also maps a public IP address to the server's local IP address (e..g, 10.10.10.8).
sounds like some network misconfiguration - outside the scope of this forum.I cannot rule that out, but other servers/websites seem to work fine with this same setup. Although, only this server is using https
>
If I access the Admin Console locally via the LAN address (https://10.10.10.8:8989) it is no longer slow, but I get booted back to the login screen very frequently (e.g, every minute or two of casual browsing through the console), and I still get the certificate error
if you want to increase this time out, you could do so by manually editing <install-root>/lib/webapps/admingui/WEB-INF/web.xml and change the value for session-timeout to say 600 (for 10 minutes).. . pl . note that this is not a supported way and you could potentially leave others to use your session if you are careless. but, if you know what you are doing .Thanks I did that. It surprises me that the default timeout appears to be 1 minute.

Ever since updating to latest version of Firefox it has been painfully slow on my Mac running OS 10.5.8.

Ever since updating to latest version of Firefox it has been painfully slow on my Mac running OS 10.5.8.
Websites just hang, and never get to where they are supposed to go. The status loop on tabs just spins and spins but never loads the site. Go to the same site on Safari and there in a second. It is like dial up slow. Have tried all the troubleshooting tips(reset, delete/re-create profiles, uninstall/reinstall, updated flash) nothing works.
Firefox had been working fine until latest update. What gives?

'''Try the Firefox Safe Mode''' to see how it works there. The Safe Mode is a troubleshooting mode, which disables most add-ons.''
''(If you're not using it, switch to the Default theme.)''
* You can open the Firefox 4.0+ Safe Mode by holding the '''Shift''' key when you use the Firefox desktop or Start menu shortcut.
* Or use the Help menu item and click on the '''Restart with Add-ons Disabled...''' menu item while Firefox is running.
''Don't select anything right now, just use "Continue in Safe Mode."''
''To exit the Firefox Safe Mode, just close Firefox and wait a few seconds before using the Firefox shortcut (without the Shift key) to open it again.''
'''''If it is good in the Firefox Safe Mode''''', your problem is probably caused by an extension, and you need to figure out which one.
Please follow the [[Troubleshooting extensions and themes]] article for that.
''When you figure out what's causing your issues, please let us know. It might help other users who have the same problem.''

Mobileme calendar freezing and painfully slow

Both my ipad and iphone4 calendars are painfully slow and freeze up. Switching from month to month now takes about 10-15 seconds while it used to be instantaneous. Anyone know if there is a fix for this.

I have this problem too. My symptoms are that when I open the calendar, the calendar starts, but appears empty. The "network in use" spinning indicator next to the wifi on symbol in the screen header is on. It takes at least 20 seconds and as much as 45 seconds before any calendar entries are displayed. If you try to change the view (e.g., from day to week) or change the date(s) displayed, it also takes a long time to display.
If I had a slow internet connection, I guess I could understand, but I have a 15Mbps down, 5Mbps up FIOS connection which is really fast. I don't think the problem is related to wifi, but I couldn't say for sure.
I don't have this problem on my iPhone 4 (also iOS 4.2.1). It's a tad slower than it used to be, but at least it displays calendar entries within a couple seconds.
When I enter a new appointment, the same thing happens--after I hit done, the entry doesn't appear for many seconds after the appointment entry form has been closed. It's like it has to send it to MobileMe and then download it before it will display it.
On top of all that, the calendar app sometimes crashes, which it never did before.
If this keeps up, I'll have to move to Google calendar, as the very long delays makes the calendar unusable in practice.

VZ 8830 - DS 4.6 - Vista - Crashes - Painfully Slow

I was previously running Windows XP with my Verizon 8830 and Desktop Software 4.3. Sycronizing with Outlook 2007 used to take about 1 to 1.5 min. tops. I have 941 contacts in my address book, and about 1905 calendar items. Now I'm running Windows Vista Home Premium, still Outlook 2007, but now I'm running Desktop Software 4.6 and Sycronizing crashes at the calendar section and is painfully slow (4 min.) up till the crash. I'm going back to 4.5 in just a min. to try that out, any other thoughts? Anyone having crashing with Vista and 4.6? And or painfully slow sync times?

Ok, I had to go all the way back down to V 4.2 to get a good sync. Now I have another crashing problem. I've just recently updated my device software which Verizon posted on theier website some time ago. Now I'm running V4.2.2.196 instead of V4.2.2.176. Now I can't sync again, with any version of Desktop software. I get to the processing device calander and it crashes. Any help?

Painfully slow internet after upgrading to Snow Leopard

hi all, i recently upgraded to Slow leopard.
My internet has soon become painfully slow, taking (literally) minutes to load pages. I have checked my modem & router, they seem to be fine as my iPhone & Vista laptop run perfectly on the same network.
does anybody know what this could be?

If you have not done so since upgrading to Snow Leopard, you should run Disk Utility and use +Repair Disk Permissions+.
Have you used Software Update to apply Apple's latest updates after upgrading to Snow Leopard. If there are updates, you should run it a second time to ensure there were no dependent updates.
As a test, you can create a new admin user account in System Preferences Accounts pane.
http://docs.info.apple.com/article.html?path=Mac/10.6/en/8235.html
Log out and log in to the new account. Try the things that caused the problems. Is it fast in the new account, or is it the same? If it is fast, then the cause is likely to be in your normal user account. If it is the same, then the cause is likely to be with the overall system (the OS).
You can also try doing a Safe Mode startup
http://support.apple.com/kb/HT1455
This will do some maintenance during startup and also load only Apple's essential system extensions and processes. Any third party software you have installed will not automatically run. Check the performance while in safe mode, and if there is improvement, restart normally to see if the problem comes back or not.

Wi-fi painfully slow on macbook pro in OSX 10.8.2

I have a Mac Book pro and over the last two days my internet has turned painfully slow on wifi - i havent loaded any new programmes and Speedtest shows no problems, still 37mbps on fiber broadband, my iPhone and PC are fine on the same wireless connection and Ethernet is perfect!!
I have tried resetting Safari and Firefox in preferences, clearing history and cookies, resetting DHCP, even using the setting 8.8.8.8. DNS server, and changing wireless channels, resetting the router, as well as running MacScan. I see people talking about turning off IPv6 but im on OS X 10.8.2 and off is not an option I have Automatic, manual and Link-manual only, i have tried all these to no joy still web pages just take ages to load :-( Any ideas?

Please read this whole message before doing anything.
This procedure is a diagnostic test. It’s unlikely to solve your problem. Don’t be disappointed when you find that nothing has changed after you complete it.
The purpose of the test is to determine whether the problem is caused by third-party software that loads automatically at startup or login.
Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards. Boot in safe mode* and log in to the account with the problem. The instructions provided by Apple are as follows:
Shut down your computer, wait 30 seconds, and then hold down the shift key while pressing the power button.
When you see the gray Apple logo, release the shift key.
If you are prompted to log in, type your password, and then hold down the shift key again as you click Log in.
*Note: If FileVault is enabled under OS X 10.7 or later, or if a firmware password is set, or if the boot volume is a software RAID, you can’t boot in safe mode. Safe mode is much slower to boot and run than normal, and some things won’t work at all, including wireless networking on certain Macs. The next normal boot may also be somewhat slow.
The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin. Test while in safe mode. Same problem? After testing, reboot as usual (i.e., not in safe mode) and verify that you still have the problem. Post the results of the test.

Why does my typing go painfully slow on my os7 devices

why does my typing go painfully slow on my os7 devices, ipad 2 and iphone 4

It's been suggested to go into the settings and reset all settings. that's helped for some.

IOS8 spotlight music search painfully slow

After installing iOS 8 on my 32gb iPhone 5S, Spotlight search for music is rediculously slow. Everything else loads just fine, but loading music & album art are a painfully slow process. In the actual music app, songs & album art load just fine, like they did in iOS 7... Any ideas on what could be causing it??? There are about 3000 songs on the phone
Thanks!

While I don't have this issue, here is something that you could try.
Navigate to Settings / General / Spotlight Search
Verify that "Music" is checked.
Uncheck it, then check it again.
Test the speed of your musical search results.
You could also try changing the "Music" results placement in the Search Results preferences. (drag and drop music, in the Spotlight Search preferences, then test the music search results speed)

My 3G service in my iphone 4s is super slow when im sending any pic it takes for ever even i changed to wifi or 3G still super slow

my 3G service in my iphone 4s is super slow when im sending any pic it takes for ever even i changed to wifi or 3G still super slow

you have done http://support.apple.com/kb/ts4429 this. so try going to repair place (paid) or try downgrading ios (not support on this website).

Mid 2011 Macbook Air Painfully slow.

Mid 2011 Macbook Air Painfully slow.
Hey everyone. I am writing about my 13 inch Mid 2011 Macbook Air.
Recently it has been extremely slow and on occasion has not started up.
I have reset the PRAM and SMC already, yet it is still very slow. I have a couple theories about what might have caused it, are they plausible?
Theory 1: It’s a software problem. I tried to upgrade to 10.8.2 but halfway through the upgrade the computer restarted and somehow I was still on 10.8.1. For fear of a big issue happening I didn’t try to upgrade again. Perhaps it is a flaw in Apple’s software update?
The important thing to note about this update is that I tried to install 10.8.2 around a month or two weeks BEFORE I started having problems. So if these issues were due to 10.8.2’s failed update then it certainly was a delayed reaction.
I would of course like to update to 10.8.2 BUT as my computer is acting EXTREMELY slow and having trouble turning on occasionally I am worried the software update will completely brick the machine. Is that possible? Should I actually finish through with the software update?
Theory 2: It was an electricity problem.
The computer died when I was sitting at a café plugged into their wall sockets. A few days later when I came back to the same spot with my old macbook which is now being used in lieu of the Air it suddenly turned black for a little while. Sensing it might be an electricity surge or something with their system I unplugged the cable. I am not sure if that was paranoia though.
Can an electricity surge or a bad outlet fry a computer? Can it fry the ram so the computer is extremely slow? Does that theory hold any water?
Thanks for your help diagnosing this problem.
All the best.

Please read this whole message before doing anything.
This procedure is a diagnostic test. It won’t solve your problem. Don’t be disappointed when you find that nothing has changed after you complete it.
Third-party system modifications are a common cause of usability problems. By a “system modification,” I mean software that affects the operation of other software — potentially for the worse. The following procedure will help identify which such modifications you've installed. Don’t be alarmed by the complexity of these instructions — they’re easy to carry out and won’t change anything on your Mac.
These steps are to be taken while booted in “normal” mode, not in safe mode. If you’re now running in safe mode, reboot as usual before continuing.
Below are instructions to enter some UNIX shell commands. The commands are harmless, but they must be entered exactly as given in order to work. If you have doubts about the safety of the procedure suggested here, search this site for other discussions in which it’s been followed without any report of ill effects.
Some of the commands will line-wrap or scroll in your browser, but each one is really just a single line, all of which must be selected. You can accomplish this easily by triple-clicking anywhere in the line. The whole line will highlight, and you can then either copy or drag it. The headings “Step 1” and so on are not part of the commands.
Note: If you have more than one user account, Step 2 must be taken as an administrator. Ordinarily that would be the user created automatically when you booted the system for the first time. The other steps should be taken as the user who has the problem, if different. Most personal Macs have only one user, and in that case this paragraph doesn’t apply.
Launch the Terminal application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Terminal in the icon grid.
When you launch Terminal, a text window will open with a line already in it, ending either in a dollar sign (“$”) or a percent sign (“%”). If you get the percent sign, enter “sh” and press return. You should then get a new line ending in a dollar sign.
Step 1
Copy or drag — do not type — the line below into the Terminal window, then press return:
kextstat -kl | awk '!/com\.apple/{printf "%s %s\n", $6, $7}'
Post the lines of output (if any) that appear below what you just entered (the text, please, not a screenshot.) You can omit the final line ending in “$”.
Step 2
Repeat with this line:
sudo launchctl list | sed 1d | awk '!/0x|com\.(apple|openssh|vix)|edu\.mit|org\.(amavis|apache|cups|isc|ntp|postfix|x)/{print $3}'
This time, you'll be prompted for your login password, which won't be displayed when you type it. You may get a one-time warning not to screw up. You don't need to post the warning.
Note: If you don’t have a login password, you’ll need to set one before taking this step. If that’s not possible, skip to the next step.
Step 3
launchctl list | sed 1d | awk '!/0x|com\.apple|edu\.mit|org\.(x|openbsd)/{print $3}'
Step 4
ls -1A /e*/mach* {,/}L*/{Ad,Compon,Ex,Fram,In,Keyb,La,Mail/Bu,P*P,Priv,Qu,Scripti,Servi,Spo,Sta}* L*/Fonts 2> /dev/null
Important: If you formerly synchronized with a MobileMe account, your me.com email address may appear in the output of the above command. If so, anonymize it before posting.
Step 5
osascript -e 'tell application "System Events" to get name of every login item' 2> /dev/null
Remember, steps 1-5 are all drag-and-drop or copy-and-paste, whichever you prefer — no typing, except your password. Also remember to post the output.
You can then quit Terminal.

IPhone website is PAINFULLY slow !

Similar Messages

Maybe you are looking for