Is booting from Tiger install disk possible to repair disk?

I have leopard 10.5.3 installed and updated, but I don't have the install disks on me, just the Tiger install disks. Can I boot from the Tiger install disks and repair the HD?

repair disk - yes,
repair permissions - no.
you can also repair disk without using an install DVD at all.
boot into single user mode by holding command+s at the chime on restart. at the prompt enter
/sbin/fsck -fy
that's the command to run "repair disk". when it's done type
reboot
to restart normally.

Similar Messages

Can I boot from tiger install disk without wiping my hard drive?

I have an old mac install disk with tiger on it and I want to be able to boot from it. Can I do that without damaging my hard drive?

You can boot from it, but if you continue through without stopping eventually it will try to install Tiger. However, if you want to install Tiger on a USB flash drive or HDD, then when you arrive at the screen for selecting a Target device, be sure to select the USB device before clicking on the Install button.
If the USB device has not been properly partitioned and formatted already, then be sure you do this:
Clean Install of OS X
     1. Boot the computer using the Tiger Installer Disc or the Disc 1 that came
         with your computer. Insert the disc into the optical drive and restart the computer.
         After the chime press and hold down the "C" key. Release the key when you see
         a small spinning gear appear below the dark gray Apple logo.
     2. After the installer loads select your language and click on the Continue
         button. When the menu bar appears select Disk Utility from the Utilities menu.
         After DU loads select the USB drive entry from the left side list (mfgr.'s ID and drive
         size.) Click on the Partition tab in the DU main window. Set the number of
         partitions to one (1) from the Partitions drop down menu, click on Options button
         and select GUID, click on OK, then set the format type to MacOS Extended
         (Journaled, if supported), then click on the Apply button.
     3. When the formatting has completed quit DU and return to the installer. Proceed
         with the OS X installation and follow the directions included with the installer.
     4. When the installation has completed your computer will Restart into the Setup
         Assistant. Be sure you configure your initial admin account with the exact same
         username and password that you used on your old drive. After you finish Setup
         Assistant will complete the installation after which you will be running a fresh
         install of OS X. You can now begin the update process by opening Software
         Update and installing all recommended updates to bring your installation current.
If you wish you can download any updates using Software Update preference panel.

My imac wont boot from the install disk

My IMAC will not boot from the install disk.

Hello, your installation disk is running under OSX??? If no the media has a problem!!!
1. Restart your mac and hold the alt (option key) to select media to install.
2. Restart you mac and hold the "c" key to boot.
an other solution is to make a partition on the hard drive and put a restore image of the Mac os X Installation dvd inside it then Restart your mac nad hold the "option" key and you will see the partition with mac os x installation and you can make a new installation from there.

Mac Pro gets kernel panic while trying to boot from Leopard install disk

Hi all,
I'm finally getting around to installing leopard on my 2006 Mac Pro. It has the x1900 video card from Apple and all firmware is up to date. The install disk upgraded my Macbook with no problems.
When booting I get the wipe to grey, kernel panic, "You must restart your Mac" screen. Any suggestions?
BTW the Leopard install disk installs OSX 10.5.0
Thanks
Pax

I finally found that the mac pro needs installer 10.5.2 or it will do the kernel panic thing. I did find a way around this though.
1) I took an external drive hooked to my macbook and installed 10.5 on it. Then booted from it and did all the updates, installed all my necessary software (ilife 08, parallels, and so on).
2) I then made sure my Mac pro's drive was currently backed up and then booted up from the backup and then used Carbon Copy Cloner to clone the new OS 10.5.4 Leopard disk onto my Mac Pro boot drive.
3) After that I used migration assistant to transfer all my user settings and such.
It all worked great and I now have Leopard on my Mac Pro.
Just thought I'd let everyone know how I got around it.
Pax

Cannot boot from OSX install disk

I need to run disk utility to repair my boot drive.
I am attempting to startup from my OSX install disk. However, I can't seem to get my machine to do this.
My computer recognizes my install disk when it's in my superdrive. It mounts on the desktop and I can read from it.
However, when i go into system preferences>startup disk, OSX does not show my mounted OSX install disk listed as an option. Also, when I hold down C on startup, my machine ignores the command. And when I hold down the Option key on startup, the only startup option shown is my boot drive, not my OSX install disk.
I've tried zapping my p-ram. I've tried booting up in safe mode and then re-trying the above.
I don't know what else I can do, short of typing in scary UNIX command lines.
I'm going completely mental here. Please help me, somebody.
If it makes any difference, I've got gobs of apps installed, notably Adobe CS3, Final Cut Studio, Firefox, MS Office 2004.

Not that this solves the booting problem, but I recommend installing AppleJack, which is free (and does run on Intel). This provides easy commands for doing a disk check in single user mode (it's the same in the end as typing the Unix commands but much easier to use), and it's much faster than booting from the CD (even if you can).
Having installed it, restart holding command-S: after a lot of text you will get the line 'Type Applejack at the prompt' - you simply do this and then it's just a question of typing 'd' to check the disk and so on. (Incidentally do not run it from the Terminal when booted normally: you must use it only in single-user mode.)

Video Ram failed, won't boot from Leopard Install Disk

Hello,
Recently, I ran the techtools software, and got a report that my video ram had failed. It was suggested that I attempt to reinstall OSX. I put in the Leopard install disk, click the install or setup button or whatever it is, click to restart. When it restarts, a gray screen comes up, but the computer never actually boots up, from either the DVD or my hard disk.
Any suggestions?

Welcome to the Apple Discussions!
Since your MacBook is still very new, you shouldn't have an problem with the DVD. If I were you, I'd call AppleCare Support and have someone walk you through re-installing Mac OS X. However, I really doubt this will help resolve what seems to be a hardware failure on your MacBook. Hopefully the folks at AppleCare Support can help figure out if you need to send your MacBook in for repairs.
-Doug

How to boot from Panther install disk?

Hi,
May be a stupid question but I want to boot to my Panther install disk1 to repair my hard disk. I start the computer with the cd in the drive but it never boots from the cd. How do I do it?
Thanks,
Dave

Dave,
Insert the Panther Install disc, then restart the computer while holding the C key.
You may also want to read Using Disk Utility and fsck to resolve startup issues or perform disk maintenance.
;~)

MacBook Pro 2010 hangs when booting from Windows install disk

Hi there,
I'm trying to install Windows 7 via Bootcamp. I've used Bootcamp before so familiar I'm with how it should work. I have a USB CD drive, which I've used on other machines OK, and an official Windows Install Disk.
After Bootcamp finishes copying over all it's drivers etc to my external USB drive, it reboots. However, whenever I try to boot from a disk it always just hangs on the Apple logo (no spinning cog/wheel). This happens whenever the Bootcamp installer performs a reboot and/or when I hold down ALT on startup and select the boot CD.
I can still boot in to mac partition. Could this be a problem with the EFI? Any help with identifying this problem or how get the information to fix this problem would be much appreciated
Thanks.

Try resetting PRAM…
http://docs.info.apple.com/article.html?artnum=2238

Kernel panic when booting from Tiger install DVD

Short version: When I try to boot up from the Tiger installation DVD, my Power Mac G5 gives me a kernel panic. Can anyone help?
Here's the story:
I have a Power Mac G5 that I've been running Leopard on for quite some time now. Unfortunately, the software I need to use (Final Cut Studio 1) has some incompatibilities with Leopard, so I was thinking I would put Tiger back on the machine in a separate partition on the second hard drive.
I tried booting the Power Mac using the retail (black label) Tiger DVD and holding down the "C" key. The Apple logo appears on screen, but is immediately followed by a kernel panic. I'm never able to access the features on the disc. The same thing happens if I try holding down "option" during boot instead: I'm correctly allowed to choose whether to boot from the hard drive or the DVD, but once I choose the DVD, I get the Apple logo and then a kernel panic.
The same Tiger DVD works fine on other computers, so I know it's not the disc. And the Power Mac itself handles everything else without problem.
I'm kind of desperate, as I need to finish this project this week. Any help you could give would be greatly appreciated!

[Apple docs: What's a kernel panic? (Mac OS X)|http://docs.info.apple.com/article.html?artnum=106227]
[Topic : kmosx: Kernel Panics? Don't panic too !|http://discussions.apple.com/thread.jspa?threadID=121923]
[X-Lab: Resolving Kernel Panics|http://www.thexlab.com/faqs/kernelpanics.html]
[Tutorial: Avoiding and eliminating Kernel panics|http://www.macfixit.com/article.php?story=20060911080447777]
[Tutorial: An introduction to reading Mac OS X crash reports|http://www.macfixit.com/article.php?story=20060309075929717]
[12-Step Program to Isolate Freezes and/or Kernel Panics|http://macosg.com/group/viewtopic.php?t=800]

Installing iLife '08 from Tiger Install disk onto Lion?

One of my iMacs (Intel) originally came with Mac OS 10.4 (Tiger), and iLife '08 pre-installed. Since then, I have upgraded to Snow Leopard, and then to Lion. The problem I have is that when the upgrade to Snow Leopard was done I did a clean installation - the result was that I lost the use of iLife '08. It didn't really bother me because it isn't our primary computer anymore.
Tonight I tried to install iPhoto and iMovie from the Original Mac OSX Install Disc 2, but when I click on "Installing Mac OS X and Applications" I get an error message that says "You can't open the application installing Mac OS X and Applications because PowerPC applications are no longer supported. I have also tried right-clicking and selecting "Show Package Contents" but I haven't had any luck.
Is there any work around for this? I'd rather not go into the App Store and pay for iLife and iMovie '11 considering I already have them as part of our newest iMac.

Unfortunately, there is no way around it; the older versions were PPC - up to and including Snow Leopard, they were supported by something called Rosetta. Apple has decided to drop support for the older architecture.
You can buy a new retail disk (not through the app store) which will include iDVD and iWeb (no longer included in the OS). I bought it because it was worth it to me to get a possibility to install and reinstall because I use iDVD a lot. The retail iLife 11 is available at the Apple store, online resellers, or ebay.

Is there any way to browse a USB disk while booted from OSX install disk?

My hard drive died on me the other day (the mac partition anyway) and I'm trying to use a data recovery program to get my data back. I have the application on my USB key, and I assumed I'd then be able to use the OS X installer disk to boot up and then run this program from the USB drive but the installer doesn't let me browse folders or quit... Is there any way to do this? I don't have another mac to firewire or anything so it's either this or order a recovery program on a bootable disk, which I really don't want to do as I need this done fast... Any suggestions?

Your utility for data recovery usually should have come with a Mac bootable DVD with its own application on it. If it didn't, contact them for a disc that will boot your Mac with the utility on it. Your other option is to get a Firewire hard drive, partition it, and install the operating system there on one partition large enough for the operating system, while leaving the other partition large enough to recover the entire unbootable hard drive.
Partitioning is described here, and will WIPE your entire hard drive:
http://docs.info.apple.com/article.html?artnum=61301

Can't boot G5 even from OS install disk. Help?

I've trolled the message boards 25 pages deep and searched all the "Can't boot my G5" threads and still haven't found anyone describing what my machine is doing so thought I'd start a new thread in the hopes someone can help me out.
Ok I have a G5 dual processor machine. (Power PC chip, not Intel) Things went bad when I tried to do an Archive and Install of Leopard (OS 10.5) The install looked as normal until I got to one minute left on the install. At that point the install never progressed. I thought maybe it was doing some behind the scenes processing and decided to leave it over night. The next day my machine was still hung on that One minute left. So obviously it was a failure. Of course now the problem is I have an install that never completed of the OS and so that partition is, I assume, unbootable. Wiped away the Tiger OS and did a 99% install of Leopard. So I had to shut down by holding the power button.
I think to myself, "No worries I can just boot from my 2nd partition holding down the Option key to select it on the boot up screen". I always keep a partition with an OS on it for times like these. So I reboot, hold option key, select my other partition, things look OK. I get the grey screen with the Apple logo and I get the wheel animation turning. (Not beachball of death but the typical circular, almost sun ray configuration thing) At this point, usually the screen will go black for a moment before the desktop loads. However, in my case once the screen goes black after the load screen, it stays black. Now let me say the monitor does NOT turn off. There is a definite difference when I manually turn the monitor off. When off it's truly black. But this is like a power on black, not true black. (If you need me to explain this better feel free to ask me to clarify)
So the untouched, pristine Tiger partition boot is a No Go. I figured I'd then give up on trying to put Leopard on my desktop machine (I use it on my laptop) and reinstall the original OS and system software from the system disk that came with my G5. I boot machine holding down eject button, place the disk in, close the drive door and shut down again by holding power button. Reboot holding C key and the same routine happens with booting from the disk. Gray Apple logo screen, sun ray circle moving, screen goes black on the attempted transition to desktop .. but stays black. I also tried booting with my Disk Warrior disk to no avail. Same thing happens. (Also tried booting from disks by selecting them manually from booting with Option key down) At first I wondered if it was a monitor issue. That maybe my desktop was up but there was an issue with the signal being passed to the monitor on the resolution jump. Thought perhaps hitting the Eject key on the keyboard when I had attempted to boot from the partition (not from disk on this test) would tell me if it was a monitor issue. If it was a monitor issue, the disk tray should open. But alas, no.
So since I cannot boot normally from any partition or disk I decided to boot into single-user mode.
I did the fsck -fy thing and it told me everything was ok. I had also previously installed applejack and I ran that and short of correcting a few permissions and dumping some unneeded caches it came back with a system OK.
At my wits end I booted into target disk mode and ran Disk Warrior on both the original half installed OS partition and the back up emergency boot up partition from my laptop. Again, everything OK. Hoped against hope that I could actually install an OS onto my G5 from my laptop but I was only given the option of being able to do it from my laptop with the Leopard disk and it would only allow me to do it if I used Disk Utility to completely format that drive first. No, thanks.
Re-attempt to boot G5. Failure. So now I turn to hardware. Disconnected everything beside the keyboard and mouse. Try again. Fail. Pulled a couple sticks of Crucial memory out of the machine and left the stock RAM. No dice. Pressed the small power unit reset button under the RAM slots. No change. Zapped the PRAM. Still nothing. Try to boot in Safe mode holding down shift key. Doesn't work.
It seems to me if I can't even get the machine to boot from the Install disk that there is something going on that is much more major than software issues.
Bad motherboard? Any ideas? Because I'm all out of ideas.

Brother, Sound74, I thought I was the only one pulling the hair out of my chest one by one the past two days. Your situation is very similar to mine, and I'm just as clueless as you are. I started getting kernel panic screens, then nothing on boot, until finally I brought it to the local genius bar. They ran all the usual software/hardware tests, updated Tiger to 10.4.11, recommended I buy Leopard and do an erase-install. My computer, of course, was working absolutely fine by this point. I bought Leopard, came home, backed everything up, then tried to install the new OS. Like in your case, it just up and quit half-way through. Screen went black and a "No DVI Signal" message came on my display (it does this when I turn it on without first turning on the computer).
So I thought, well, maybe it takes a really long time to erase-install, and the monitor is just waiting for things to kick back in. I've always upgrade-installed before, so I couldn't tell if this was normal or not. But about half an hour later, my fans kicked in so fast I thought I had a P-51 Mustang taking off in my studio. I waited a bit more and finally force-shut-down my system. Not knowing what to expect, I nervously tried to re-boot.
Nothing. Zip. I can't safe boot, I can't boot from the installer disc, etc. The only thing I can do is the option-key thing whereby you choose the startup disc. And of course, it only gives the Leopard install disc as an option, because now the entire HD has been erased! But when I choose the Leopard disc, of course it doesn't work.
So I have a nice $3000 paperweight sitting in my studio. I guess I'll have to bring it back to the Mac store, where if it costs more than $300 to fix, I'm going to say screw it and put that dough toward a new iMac.
Sorry I couldn't provide any helpful info, but I just wanted you to know you're not alone in suffering the slings and arrows of outrageous technology.
Keep me posted on any solutions you discover, and I'll do the same.
Noochy1
PS My applecare expired a month ago! AAAAARRRRGGGHHHH!!! **** Murphy and his stupid laws.

Leopard lost my external HD, how to boot from Tiger

When I upgraded (?) to Panther, it wanted to do a backup to my external HD, but it was going to be to large, so I told it not to. The next day when I started up, I typed in the password to my external HD and got a window saying Device not found. I have been following the discussions af many others with the same problem, so I'm getting experimental
I would like to boot from my Tiger disk, but when I insert it in the DVD drive and choose it in startup disk, it restarts, but wants to install. What I am trying to do is to boot from my Tiger disk, turn off password protection for the external, then go back to Leopard, hopefully to a useable external again.
How do I boot from an install disk so I can get to my dock and Finder?

David Tinker wrote:
When I upgraded (?) to Panther, it wanted to do a backup to my external HD, but it was going to be to large, so I told it not to. The next day when I started up, I typed in the password to my external HD and got a window saying Device not found. I have been following the discussions af many others with the same problem, so I'm getting experimental
I would like to boot from my Tiger disk, but when I insert it in the DVD drive and choose it in startup disk, it restarts, but wants to install. What I am trying to do is to boot from my Tiger disk, turn off password protection for the external, then go back to Leopard, hopefully to a useable external again.
How do I boot from an install disk so I can get to my dock and Finder?
You have the right idea. It would be easier if you had another computer with Tiger.
Try this. Boot into the Tiger CD by holding down the "C" key but do not install anything, In the Utilities menu you should have an option to log in as a single user in the terminal mode.
From there you can access the external HD and turn off the password. You will need the instructions how to do this in a terminal from the HD manufacturer or someone else on these boards who had done it before.

EMac won't start from startup install disk

Aloha gang,
Our school purchased 25+ seats volume license of 10.4 last year and to date I have used 15. Most upgrades have gone on without a hitch but today I'm trying to upgrade some eMacs (same models as I have previously upgraded without problem) and it will not start up from the disk no matter what I try. I've tried:
* putting in the disk, clicking on install, clicking on restart so it restarts from the install disk
* putting in the disk, starting the computer and holding the C button
* putting in the disk, starting the computer and holding the option button to choose the install disk
None of those have worked. All that happens is the grey screen with the darker grey apple and the spinning thingy beneath it. I thought it might be that I was being impatient so I started it again, went to eat lunch and when I returned it was exactly where I left it. Any suggestions?
Oh yeah - I have tried using the original purchased media as well as backup copies of the media in all instances.
Thanks for any help you can give, gang!

nalani:
Thank you for indulging my ignorance and so graciously enlightening me as to your situation.
It seems to me that the difficulty you are experiencing has to do with individual computers not responding appropriately to the discs from which you are trying to boot them. The disks themselves may not be the issue at all, since you have previously booted other computers from them.
My first suggestion would be to check the computers themselves to see if they have issues that need to be corrected. If those computers are running previous versions of OS X and you have the install disks for them, see if you can boot from them and run Repair Disk. I would also check for hardware issues by running the appropriate Apple Hardware Test disk. BDAqua's suggestion to Resolve startup issues and perform disk maintenance with Disk Utility and fsck is appropriate, especially if you are unable to boot from an install disk to run Repair Disk.
BDAqua's other suggestion also has merit. That is, using one of the computers that will boot the disk as Host, boot the recalcitrant computers into Firewire Target Disk Mode and run Repair Disk and if everything checks out OK, do the installation in that way.
No one is questioning the legality of what you are doing. It is just that most of the users who post have a single user or family license at best, so your licensing situation is a bit rare around here.
Please do post back with an update of how things go if you attempt any of the suggested approaches.
Good luck.
cornelius

Tiger install disk (10.4.6) MacBook Pro - possible upgrade from 10.3.9????

Can I use the Tiger install disk (10.4.6) that came with my MacBook Pro to upgrade from 10.3.9 on my Powerbook to 10.4.6 on my Powerbook?

You're welcome.
Leopard requirements/10.5.x...
* Mac computer with an Intel, PowerPC G5, or PowerPC G4 (867MHz or faster) processor
minimum system requirements
* 512MB of memory (I say 2GB at least)
* DVD drive for installation
* 9GB of available disk space (I say 30GB at least)
You have to call Apple &likely ask for a Product Specialist to get it, if they still have it!

Is booting from Tiger install disk possible to repair disk?

Similar Messages

Maybe you are looking for