Ise and switch authentication and privilege level

Hi Guys,
I'm working on an eval on vmware. I have got everything working for wlan authentication and I’m working on shell authentication for switches. On the ACS you have the possibility to give the user privilege level on the switch. You can do this with shell profiles in ACS.
Is there a way to get this done in ISE? I was thinking to make a result policy elements but I can't find a shell profile or privilege attributes like in ACS.
For the record, switch authentication is working with Active Directory. I only need to know how to give the right return attribute.
I appreciate any help!
Sander

@Sander,
You were in the right area. 
Policy->Results->Authorization->Authorization Profiles.
Create AuthZ profile for Access-Accept and Under the Advanced Attributes Settings you can use:
Cisco:cisco-av-pair = shell:priv-lvl=15
or whatever privilege level you want to assign.
On your AuthZ rule, match the conditions and apply the created profile.

Similar Messages

  • I bought a new iPhone 6 and switched carriers and am trying to get my voicemail and instant messages ported over to the new phone

    I bought a new iPhone 6 and switched carriers and am trying to get my voicemail and instant messages ported over to the new phone

    Restore from your backup.  For voicemail contact your cell phone provider.

  • Why does Quicktime tell me it can't play certain videos created with my Phantom 2 v3 drone ? I fly it and switch back and forth from video to still pics and while I may have filmed four videos sometimes Quicktime tells me that one of them can't be pl

    Why does Quicktime tell me it can't play certain videos created with my Phantom 2 v3 drone ? I fly the drone and switch back and forth from video to still pics and while I may have filmed four videos , sometimes Quicktime tells me that one of them can't be played . Checking the info shows that each of the unplayed videos was saved in the same mp4 format as the playable ones yet some of my most important videos won't play . It's getting very frustrating .

    first; I use Perian, that helps even though it is no longer supported, (must have for avi files)
    the apple-cores at apple have gotten very sloppy -- quicktime is a bit finicky and flakey. 
      example,   occasionally (when copy file from quad's card to hard drive)  the avi will show up as a 'mov' file and qt plays it no problem and no conversion.
    but that is very occasionally,  most of the time qt won't convert the file,   -- iMovie won't open an avi without Perian installed  ,  I don't know how that effects qt.
    qt 7"pro" is no good either, (qt 10 does everything it does and for NOT the extra $35)  
    I have gone to VLC  and MPlayerX  for direct playback for drones and cameras.  

  • How do I keep multiple windows open and switch back and forth?

    How do I keep multiple windows open and switch back and forth?

    billyg27,
    if you hold down a Command key and press the Tab key, it will show a set of icons representing your currently opened programs. Press Tab until you arrive at the program you’d like to switch to, and then release the Command key.

  • I have a G5 PPC Dual 20" Mac Displays - I want to incorporate a Mac Mini and still use my keyboard and Monitors and Switch back and forth. How do I do this?

    I have a G5 PPC Dual 20" Mac Displays - I want to incorporate a Mac Mini and still use my keyboard and Monitors and Switch back and forth. How do I do this?

    The Hatter,
    I am a novice at Mac so I read all I can.  From what I understand the NEC monitors I bought require Display Port for their maximum performance.  The GTX 680 only has DVI outputs.  Difference from what I understand is larger bandwidth with the DP.
    You said I have the 4000 for CUDA.  I am not all that familiar with CUDA and when I do read about it I do not understand it. 
    A concern I have is, that if I connect the 2 high end NEC monitors via the 5770, using it's 2 Display Ports I would have nothing connected to the 4000.  Is the 4000 doing anything with nothing connected?  I read where in a PC system the 2 cards would interact but in a Mac system they do not.
    Bottom line, as I see it, the 4000 will not be useful at all to me, since I want a dual monitor set-up.
    So far the 5870 seems the best choice, higher band width than the 5770, and it has 2 Display Ports to optimize the NEC monitors.
    I'm not sure how fine I am splitting hairs, nor do I know how important those hairs are.  I am just trying to set up a really fast reliable system that will mainly be used for CS6 and LR4.  Those NEC monitors are supposed to be top notch.

  • We have two email accounts and my wife cannot access hers. Is it due to new software upgrade? Have tried rebooting iPad and switching of and on the wifi!

    We have two email accounts with virginmedia. After a day of intermittent messages yesterday, today my wife's email cannot connect to server. Had no problems before. Tried rebooting iPad and switching off and on the wifi to no effect.

    FYI, this is a user to user technical support forum.
    No one from Apple monitors, reads, or responds here.
    Try the following:
    Settings > General > Reset > Reset Network settings
    If the Wi-Fi is still not working, basic troubleshooting from the Users Guide is reset, restart, restore (first from backup then as new).  Try each of these in order until the issue is resolved.
    The vast majority of users upgrade with absolutely no issues.

  • My iPad randomly becomes blue and switches off and switches on its own after downloading installing iOS 8"" is it happening to any one else ?

    Mine is a iPad mini with retina display second generation...and its bn just 2 months i bought my iPad...initially when I updated to iOS 7 , had downloading app issues...now after installing iOS 8 , iPad randomly becomes blue when Ian browsing or checking something online and switches off ,and later switches on its own...it's frustrating...plz help

    Hello Drvsowlaks,
    Thanks for using Apple Support Communities.
    To isolate and troubleshoot this issue I'd like you to first reset your iPad by following the steps in the article below.
    Turn your iOS device off and on (restart) and reset
    If the issue persists, please back up your iPad, and then restore it to its factory defaults.
    Use iTunes to restore your iOS device to factory settings
    Take care,
    Alex H.

  • I'm using a macbook pro 2011 15",while i was charging it,i accidentally switched off the power supply while it is half way charging,will the battery get damaged if charging got interupted and switched on and off?

    i'm using a macbook pro 2011 15",while i was charging it,i accidentally switched off the power supply while it is half way charging,will the battery get damaged if charging got interupted and switched on and off?

    you are welcome

  • Comparing switch control and switch output and setting switch control accordingly

    Hello,
            i am developing a GUI for a system which contains relays to control the motors. For the same purpose i am using switch control on my GUI to control these relays.when these relay  are turned ON by the switch control on my GUI, they give back status to the GUI, which i am displaying as a switch status .
    Now the switch control and switch status on GUI must be same every time so that user can know the actual state of relay and control it.
    Now i have a condition when i have already turned ON switch from my GUI but due to some reason (may be communication fault or anything else) rellay is not turned ON and i get status of relay as OFF on my switch indicator. So the situation is" the switch control is in ON state and switch indicator displays OFF state".  which is practically wrong.
    I want that in this case the GUI should detect the status of the switch indicator and if the switch control is not the same , the switch control should be set as per the switch indicator so that user can use the switch again to turn the switch ON

    Hello Mike,
                        Thanks for the response!!
    As i have described the situation above, in any case if switch control fails to send message to relay due to some hardware fault , in that case relays will be off and the switch on GUI will be ON , and user will think that the relay is ON.Which is false condition.
    i tried to use property value(signl)   to give back the status of switch indicator to the switch control.
    You can have a look at attached files which i have made as demo.
    Now the problem is when i run my GUI for the first time all the switch on the front panel are off by default which creates a conflict to control the switches.
    Besides i am unaware of the timing events and how to implement it in my application . It would be great if you could provide some more details about it.
    Thanks & Regards,
    Shivkant Paswan
    Attachments:
    switch control trial.zip ‏16 KB

  • I want to work on my web-site and switch back and forth between the public view and the admin view but Firefox keeps closing one of them - how do I disarm this?

    Before upgrading to this version of Firefox I could simultaneously have my public version and my admin version of my web-site open. I could make changes in the admin version and then check to make sure the public version registered and displayed the changes just as I wanted them. Now it keeps switching so both of them are public or both of them are admin. I want to know how to disarm this function. Thanks!

    Start Firefox in [[Safe Mode]] to check if one of your add-ons is causing your problem (switch to the DEFAULT theme: Tools > Add-ons > Themes).
    See [[Troubleshooting extensions and themes]] and [[Troubleshooting plugins]]
    If it does work in Safe-mode then disable all your extensions and then try to find which is causing it by enabling one at a time until the problem reappears.
    You can use "Disable all add-ons" on the [[Safe mode]] start window to disable all extensions.
    You have to close and restart Firefox after each change via "File > Exit" (Mac: "Firefox > Quit"; Linux: "File > Quit")

  • Problems with file permissions and authorization/authentication and hostname (using ddns)

    hey guys!
     decided to rewrite this entire question...it was too hard to understand what i want. 
    I have a student version of server 2012 r2. I installed like 50 roles, and then deleted 90% of them. i have....a bunch of webserver roles, almost all of them i bet, and misc others. no AD or dns roles..i deleted those i thought they might have been the problem. 
    I connected this to a dynamic dns courtesy of No-ip.com. example.ddns.net
    when installing a blog or cms, and I am asked for the server name (for database) do i use localhost, 192.168.1.###, my router ip, computer name, example.ddns.net, or something else? 
    Same question above for iis bindings! What do i put for the host?  
    secondly, what file permissions do i set up? I can't seem to access umbraco, for example, from outside the network unless i use windows admin credentials in the physical path credentials via IIS advanced options. 

    Hi,
    The issue is related to IIS, I suggest you ask for help from IIS forum for better and accurate answer to the question.
    http://forums.iis.net
    Best Regards,
    Mandy
    We
    are trying to better understand customer views on social support experience, so your participation in this
    interview project would be greatly appreciated if you have time.
    Thanks for helping make community forums a great place.

  • What is wrong with my ipod when it charges for 2 minutes then stops charging and switches back and forth

    I plug it in then it wont charge then my sister plugs hers and and hers charges

    Do you have a power adapter? Sometimes iPod doesn't charge in computer when the battery is extremely low. That happened to me. Luckily, I had a power adapter. Now it works as usual. Hope can be of help!

  • Whenever i charge my ipod 5th generation i have to move the charger around for about 5 minutes,it doesnt want to charge and switches on and off?

    whenever i charge my ipod 5th generation,i find myself moving the charger around for about 5minutes,the first few months the charger has worked fine now it is playing up,turning on and off charge?

    I would make an appointment at your local apple store and have them check it out. The warranty covers manufacturer's defects. Unfortuantely, if you inadvertantly cause some damage in your wiggling, it could be determined that you broke the port - regardless if it was malfunctioning before or not. Have them look at it and see what they say.

  • My i pad just froze and switched off and wont turn on?

    i pad froze and wont turn on, any tips?

    Frozen or unresponsive iPad
    Resolve these most common issues:
        •    Display remains black or blank
        •    Touch screen not responding
        •    Application unexpectedly closes or freezes
    http://www.apple.com/support/ipad/assistant/ipad/
    iPad Frozen, not responding, how to fix
    http://appletoolbox.com/2012/07/ipad-frozen-not-responding-how-to-fix/
    iPad Frozen? How to Force Quit an App, Reset or Restart Your iPad
    http://ipadacademy.com/2010/11/ipad-frozen-how-to-force-quit-an-app-reset-or-res tart-your-ipad
    Black or Blank Screen on iPad or iPhone
    http://appletoolbox.com/2012/10/black-or-blank-screen-on-ipad-or-iphone/
    What to Do When Your iPad Won't Turn On
    http://ipad.about.com/od/iPad_Troubleshooting/ss/What-To-Do-When-Your-Ipad-Wo-No t-Turn-On.htm
    iOS: Not responding or does not turn on
    http://support.apple.com/kb/TS3281
    Home button not working or unresponsive, fix
    http://appletoolbox.com/2013/04/home-button-not-working-or-unresponsive-fix/
    Fixing an iPad Home Button
    http://tinyurl.com/om6rd6u
    iPad: Basic troubleshooting
    http://support.apple.com/kb/TS3274
     Cheers, Tom

  • Tacacs AAA and privilege level 7

    I've setup a group on tacacs server called acsrestricted and mapped it to AD security group. I've set this group to privilege level 7 on tacacs server.
    I need this group to view the "show run" config on a router. Privilege level 7 allows the user to use some other show commands but not "show run". How can i configure this on tacacs?

    Michael
    I am not sure that I am understanding your post correctly. As I understand it you have created a group for some users who would operate at privilege level 7. I gather that this works and that users in this group do authenticate and are assigned to privilege level 7. You say that some show commands are assigned to them but not the show run command. This would seem to be simple to solve - you make sure that show with a parameter of run is assigned to them. But there is something not simple that makes this not work. Part of the Cisco implementation of privilege levels is that in show run a user can not view any parameter that they do not have permission to change.
    Perhaps it might work for your situation if you give those users access to show config. show config does not have the same restriction as show run.
    HTH
    Rick
    Sent from Cisco Technical Support iPad App

Maybe you are looking for