Issue with control cycle

Hello all,
Can somebody please tell me how to find who created a particular control cycle?
Is there a way to find the id of the person who created/modified a control cycle?
If yes, please tell me.
Thanks and Regards,
Umakanth.

Hi
Use Transaction AUT10 with T-codes PK01/PK02.
Give the period for which you want to find changes.
keep the changed by field open , i.e dont put your user id there.
and execute, you will get list of all changes done through creation or chage transaction of control cycle.
check it out and revert back for further discussion.
Hope it helps you.
regards
Ritesh

Similar Messages

"Possible precedence issue with control flow operator"

Hi guys
I have following Problem:
Yesterday I made a distribution update from debian wheezy to debian jessie.
Since then I got a problem with a plugin which I'm using for Icinga a monitoring system.
When I run it, I got the error that there is an "Undefined subroutine".
I read on google that I can fix it, with reinstalling the vsphere SDK, but the installation stuck at "CPAN is downloading and installing pre-requisite Perl module "SOAP::Lite"".
I can skip this step with Ctrl+C and at the end it says "This installer has successfully installed...".
But when I run the Plugin I get the error message "Possible precedence issue with control flow operator at /usr/share/perl/5.20/VMware/VICommon.pm line 2147." and the whole plugin stucks.
I tried the following step which I found in this forum and the error message doesn't appear, but the plugin still stucks...
Re: VMware-vSphere-Perl-SDK-5.5.0-1384587 broken with perl 5.20
I have also Perl 5.20.2...
Can you guys help me?
Vinzenz

Ok I could fix it...
I changed the line 2147 to
return (defined $user_agent->cookie_jar and
$user_agent->cookie_jar->as_string ne '');
And this time I waited for a long time and I get a error message that there is a problem with SOAP.
The solution was to downgrade Net-HTTP and libwww-perl with following commands:
perl -MCPAN -e shell
o conf urllist push http://backpan.perl.org
install GAAS/Net-HTTP-6.03.tar.gz
install GAAS/libwww-perl-6.03-tar.gz
The second Command loads older releases to the urllist.
Thx for your help and I hope I could help others with the same problem.
Vinzenz

Issues with AUTO cycling through ....

I'm trying to do this:
Any help with one or the other is very much appriciated !!!
1) When the Timer is finish auto cycling through the tabs (1 to 16) of the ViewStack, and switching over to tab (1) to STOP, I would like to address a function to do something ???
The question is now how to write the code to ID that the Timer has come to a STOP on tab (1), and how can I incoperate this into the existing (onTimerOne) function.
2) The second item I'm after is that if I'm amnualy select any tab (1 to 16) to address also a function to do something ???
3) The third item I'm after is to automaticly zero (0) the ViewStack to tab number (1) if I click a Btn.
<mx:Script>
<![CDATA[
    import flash.events.TimerEvent;
    import flash.utils.Timer;
    private var timerOne:Timer;
    private function initOne():void {
        timerOne = new Timer(5000, myViewStack.numChildren);
        timerOne.addEventListener(TimerEvent.TIMER, onTimerOne);
    private function onTimerOne(evt:TimerEvent):void {
        if(myViewStack.selectedIndex == myViewStack.numChildren-1) {
        myViewStack.selectedIndex = 0;
        return;
        myViewStack.selectedIndex++;
    private function autoOne():void {
        if (!timerOne.running) {
        timerOne.start();
    private function manualOne():void {
        if (timerOne.running) {
        timerOne.stop();
]]>
</mx:Script>
4) Well, the fourth item I'm trying to work out is as I'm reading my data from an Xml file to have a TextArea which shows the different countries from the Xml file for each ViewStack tab while auto cycling through these tabs (1 to 16).
The diffuculty here is that I use this Xml with a specific urlID="1" to urlId="16" as part shown below.
<urlsOceania>
    <urlOceania urlID="1"/>
    <searchCountry>American Samoa</searchCountry>
    <etc></etc>
</urlsOceania>
I'm reading all the other items this way:
source="{urlsOceania.urlOceania.(@urID==1).etc}"
Thanks in advance aktell2007

Thanks for the confirmation. 7 miles away is most likely using the same VZW tower but it does confirm the problem is not in your current location for us.
You can look up local tower locations from many public websites such as the following:
www.antennasearch.com
www.cellreception.com
http://www.evdoinfo.com/content/view/2990/63/
The signal of -65 shows you have strong reception but it doesnt show the entire picture. Your tower could be overloaded or unauthenticating you. There are lots of little issues that exist outside of the raw signal strength between the towers and the connecting devices that we users have no control over. As you may guess only a tower tech has access to identify and correct these things.
Based on the picture of the back of the MBR1515/Netgear N300 router from Netgear I would assume that only a normal sized SIM card will fit. I would not assume a micro SIM card will fit. Since I do not have access to either of the VZW or non-VZW 4G LTE router I cannot confirm if it will work or not. You might have to give Netgear a call and ask. Based on what I can see from the User Guides of both devices the SIMs used for each should be compatible with eachother.
If you decide to purchase the non vzw version please post back your findings for us.

IOS 7.0.2 update issue with Control Center

After updating, the iTunes controls no longer work in Control Center. I've already tried rebooting with no changes. Anyone else having this issue?

Ok, well, after a few more reboots and it finaly started to respond. Wierd.

Issue with controlling extraction

Hi
Due to an sap r3 error my data load from co_om_cca_9 to a data target is stuck from october . But now its Ok in sap r3 . How can i load the data from october till date to my data target ?
Please suggest .

Hi simon !
Stuck means is failing from last october .
Yes .. I am running deltas .
Yes.last time stamp is set to X (that is for 09.05.2008)
In BWOM_SETTINGS table most recent has no value .
We have a ODS for to resolve for duplicate records.
Please also tell me the details of these .

Control Cycle information missing in COR2

Hi experts !
I encountered an issue in all client about reservations update with control cycle values for alternative items.
We use alternative items in a standard manufacturing BOM. (Strategy 1; probability of usage 100 % and 0 % for the others). These alternative items are WM managed and the control cycle are properly maintained.
When we create the process order, reservation items are created for all items (even for items with a required quantity to 0 which are the ones with probability usage 0 %) in RESB.
When releasing the process order, when the system is reading the control cycl information, only the reservation items with a required quantity different from 0 are updated with the WM info : Staging ind. (BERKZ) , Warehouse No (LGNUM), Storage Type (LGTYP), Storage Bin (LGPLA)
I could not find any customizing functions to manage reservations and control cycles.
I looked for a SAP notes but could not find ant soving our issue.
Do you have any solution to our issue ?
Regards and many thanks for your help...
Philippe

Dear,
Please refer the OSS Note 1136321 - COMAC: Double Transfer Requirements in WM Material Staging
Or you can raise the issue to SAP in that case.
Regards,
R.Brahmankar

UI issues with beta 8

First off, let me confirm that the correct way to upgrade from beta 7 to beta 8 was just to install beta 8 on top on beta 7. Is that correct or should I have deleted beta 7 first?
If that's correct, then I am having a whole bunch of issues.
First issue: My basic Tab Bar Controller application does not display (in the simulator) the UIView the first time you visit the tab but does display it the second time you visit a tab. Anyone every seen this and if so any ideas on the root cause?
Second issue: Once the view does display, I am having some issues with controls. When I try to add "IBOutlet NSTextField* distanceLabel;" to my interface for the view controller (subclassed from UIViewController), the compiler flags this with "syntax error before NSTextField". Am I missing some special syntax sugar for the iPhone here?
Third issue: I have hooked up a button "touch up" event to a method in my controller with this signature: "- (IBAction) start:(id)sender;" This hooks up all nice and good but when the button is pressed, the app crashes in GDB with a selector not found error.
Anyone seen this with beta 8 or otherwise?
Thanks,
Tim

Actually, i just notice this in GDB. This looks like a problem -- has anyone ever seen this before?
This GDB was configured as "i386-apple-darwin".warning: Unable to read symbols for "/System/Library/Frameworks/UIKit.framework/UIKit" (file not found).
warning: Unable to read symbols from "UIKit" (not yet mapped into memory).
Program loaded.
I also reformated my dev machine and clean installed beta 8 so I am pretty sure that is not the issue now...
Tim

Issue in creation of control cycle

Dear Gurus,
During creation of control cycle (LPK1), the fields for source information is not appearing in my system.
I compared control cycle in a different ECC system where source information is appearing.
How can make the screen appear in my ECC system.
Please find the screenshots.
Any pointers will be highly appreciated.
This thread is further to the threads in Production Planning and LE/WM Forum. I could not resolve the issue with the threads.
Hope that I will get any pointer in EWM forum.
http://scn.sap.com/thread/3609441
http://scn.sap.com/thread/3610822
With Regards,
Malay

Hello Malay,
Can first contact your ABAPer and ensure the bottom screen is not an Screen Enhancement?
If it is a some custom development, your ABAPer can help you on the logic behind it.
Else, Let us know.
Regards,
Sathish

Issue during creation of control cycle

Dear Gurus,
During creation of control cycle (LPK1), the fields for source information is not appearing in my system.
I compared control cycle in a different ECC system where source information is appearing.
How can make the screen appear in my ECC system.
Please find the screenshot.
Any pointers will be highly appreciated.
This thread is further to the thread in Production Planning Forum
http://scn.sap.com/thread/3609441
With Regards,
Malay

Manish,
I do not understand how this going to solve the issue because why we need both KANBAN and WM control cycles for one material withdrawal for production?
Br
KK

Handling Unit Management and supply areas with WM/control cycles

Dear all,
has anyone come across the issue how to handle a replenishment process for production with supply area within WM and Handling Unit Management?
Normally a supply area is being staged via control cycles. in the supply area, all storage units get lost (standard functionality as far as I know). When we post the GI, the components will be taken out of the supply area, backflushing is not allowed as far as I know.
Now: what happens if HUM is switched on? Do we have to enter a HU for these GI's as well? Or does the supply area keep the information of the SU/HU? I want to avoid that the users have to tell the system the HU no. for every screw they take/consume...
Thanks & regards
Christian

Hi,
(as already described,)
it is possible to use handling unit management together with lean
warehouse management. You activate handling unit management independent
from storage unit management (that is only possible in case of full-WM
as far as I know).
Only in case if storage location is full-WM- AND HU-managed the storage
unit management is always active and HU numbers are taken over as SU
numbers. In all other cases HUM and SUM are independent from each other
and number ranges must be set a way that they are not overlapping.
Regards,
Ely

Having 2 small issues with 10.4.3 interface - shift click & control click

I am having two issues with 10.4.3 on my mom's computer.
1) I Control-Click the mouse and I do get a shortcut menu on the desktop, on icons, etc. How can I get this back? I can not seem to find a preference that sets this.
2) I am in iPhoto and would like to select multiple film rolls (consecutive rolls) by clicking the first and then clicking the last one that I would like and it is working like I am comand clicking and only selecting the two rolls that I have clicked on and not the ones in between.
Any help in how to work this out would be great.
Happy Turkey Day!
K

1) I Control-Click the mouse and I do get a shortcut menu on the desktop, on icons, etc. How can I get this back? I can not seem to find a preference that sets this.
Do you have any third-party items in:
/Library/Contextual Menu Items/
/Users/YourUsername//Library/Contextual Menu Items/
If you do, try dragging them onto your Desktop and then retry control-clicking.

Issue with copy control of Delivery document to Billing document

Hi All,
I am having some issue with copy control of Delivery document to Billing document.
I am having two line items in Delivery documetn, one is for item to be delivered to customer and other which is created due to batch determination.
Now , when I create billing document (VF01) with reference to this delivery document , I want only one line item (for the one which needs to be delivered to customer).
I have used following things in copy contro from ZLF to ZF2:
Copying requirements: 004 ( Deliv-related item)
Data VBRK/VBRP: 007 "(Inv.Split (Rec/Div))
Is it correct or shall I use something else, so I have only one line item in Billing document.
Regards
Nidhi

Pls. search the forum.
Pls. refer the below link -
Line with 0 quantity for main item with batch split
Thanks

Issue with input field in table control

Hi,
I have an issue with field acgl_item-rstgr in the table control.
I have created a screen program with a table control.
In the control i have added a dictionary field as acgl_item-rstgr.
When i execute, do f4 on the input field, select a value and press enter, then it is showing me
error as 'Entry 'val' does not exist in T053R (check entry). Its really weird to understand this. I have selected the value
from f4 and even then it says this. Its working for all other columns, but not working only for RSTGR.
Plz help me on this regard.
Code is like this.
TYPES : BEGIN OF ty_rstgr,
rstgr TYPE RSTGR,
END OF ty_rstgr.
TABLES : ACGL_ITEM.
DATA : it_rstgr TYPE TABLE OF ty_rstgr.
DATA : wa_rstgr TYPE ty_rstgr.
CONTROLS : table TYPE TABLEVIEW USING SCREEN 100.
PROCESS BEFORE OUTPUT.
MODULE STATUS_0100.
LOOP AT it_rstgr INTO wa_rstgr WITH CONTROL TABLE.
ENDLOOP.
PROCESS AFTER INPUT.
MODULE USER_COMMAND_0100.
LOOP AT it_rstgr.
ENDLOOP.
Thanks,

Hi Navitha,
Its Check Table concepts for the error u stated. Please check wht the Search help ur using...Because for this field there is no search help at value table level...Use search help that hold all master data or create a custom search field in SE11 level or in program level.
Cheers,
Naveen

Issue with Period Control Table after copying Essbase adapter

Hi Experts,
I'm working on version 11.1.1.3 and have copied the adapters (Essbase, Pull + EPRi) in the work bench so I can add an additional target for the FDM application. However, I have an issue with the import process; it returns an error with the Time & Periods (I guess it's something to do with the Periods category).
I have reimported the Periods Control Table and updated the new application's Target Period & Year (whilst changing the system code in the Application settings to the newl adapter) and still receive the same error message.
Any direction or thoughts would be welcome.
Thanks
Mark

The time periods do not copy. You need to maintain them through the UI or upload them from excel. There is a KM article on this if you need additional detail.

Weird issue with sound control?

I am not sure what is going on with my audio controls. I use MSI to control my audio (it's connected to the motherboard). The strange thing is, a crack appears on the "Reset EQ Setting" button.
See link: http://www.facebook.com/photo.php?pid=30673857&l=2041bbbec3&id=1458901123
That wasn't there when I first got the computer. Is there any way I could reinstall this? What could have caused the "crack" to appear? Has this happened to someone else?
I have also noticed that sometimes when I am playing music, the sound wavers, as if I am adjusting the volume slowly up and down by 1 degree. Is this an issue with my motherboard or WMP? Please answer both questions.

Quote
I cannot find the MS-XXXX anywhere!
Please read this thread:
https://forum-en.msi.com/index.php?topic=113146.0
If you can't find the model number, please look at the BIOS P.O.S.T. Status Screen and write down the full BIOS ID String as it appears in the following example picture:
Example (taken from the second picture): A7375NMS V2.2
The BIOS ID String will tell us a lot about the System. In the above example, the following information can be decoded from the ID String:
A...AMI BIOS Implementation
7375 ... Model Number (=MS-7375)
N... NVIDIA Chipset Board
MS... MS Standard BIOS Release
V2.2 ... BIOS Version 2.2

Issue with control cycle

Similar Messages

Maybe you are looking for