Issue with printing to a network photocopier

We are a small school where the teachers all have Macbook Pro laptops. For a while we have been having intermittent issues with printing to the Photocopier, today is an example.
Teacher tried to print, worked fine, then tried again 15 min later, received message Printer is in use (I was standing next to it and it wasn't in use!) tried again 10 min later, printed fine.
Teacher tried to print, spooled for about 5 min then printed, tried again, printed fine.
From the CUPS error log there are the following:
- The Printer is in use
- ICC Profile "/Library/Printers/Sharp/Profiles/SS0HIN0.icc" does not exist.
- Remote host did not accept data file(32)
- The printer did not respond
- Stopping unresponsive job
- The printer is not responding
They are all on wireless. There is no network issue as I can ping the photocopier, get onto the Internet etc.
They don't print via a server, they all have the photocopier installed on their macbooks as an IP printer using LDP.
Thanks

You'll need to manually create the folder and install the profiles. From the finder select Go, Go to Folder. Enter "/Library/Printers/Sharp/Profiles" without the quotation marks, Go. You might have to manually create the Profile folder. You can download this disk image from Sharp that contains the icc files here; http://www.sharpusa.com/ForBusiness/DocumentSystems/MFPsPrinters/MX4110N.aspx?vi ew=drivers
Drag and drop the icc files from /MX-C26/Profiles to /Library/Printers/Sharp/Profiles
Also make sure you install the drivers from MX-C26 for the appropriate version of OS X you are running.
Hope this is clear.

Similar Messages

Acrobat 9 Pro issues with printing and now updating !!! :(

hello
I had an issues with printing from my gmail account or from windows live mail
so I made a complete re-installation
now I am stuck with version 9.3.0 and when I check for updates I get a message
UPDATER IS ALREADY RUNNING
only... it's not running and nothing is updating !
I made a restart... just in case... it did not change anything
as to the printing issue, in case some of you have met it and cleared it...(hope)
this was with version 9.5.0
I get no error message but no pdf is created, only a text document with this :
%%[ ProductName: Distiller ]%%
%%[Page: 1]%%
72gmvi not found, using Courier.
44dcmta not found, using Courier.
%%[ Error: invalidfont; OffendingCommand: xshow ]%%
Stack:
[96 96 97 72 96 42 64 0]
%%[ Flushing: rest of job (to end-of-file) will be ignored ]%%
%%[ Warning: PostScript error. No PDF file produced. ] %%
not a good start for my week... I hope yours is nicer
I'm running Win7 Ultimate x64

thanks Mylenium
the font association problem is something recent though, since I used acrobat to print mails directly from my gmail account previously...
it's galling but I installed a free pdf printer which does the job, I needed copies of these mails urgently !
as to the update issue, I see no aum.exe, msiexec.exe or setup.exe running... but that's quite above my head... do I look for those exact processes or are they generic names for processes ?
does my question make sense ????

Issues with printing purchase order

Dear friends,
I'm having some issues with printing purchase orders.
Normally when I create a purchase order via ME21N and then when I save the purchase order it then gets automatically printed.
Suddenly it is not anymore working. I have created a purchase order this morning and it did not get printed. I get the message "frontend is not available"when i check the spool in SP01
The funny think is if i call up the spool nr via SP01and then do a reprint then i'm able to reprint.
What can be possibly the issue that I can't print the purchase order when I create the purchase order via ME21 when I save the purchase order? Can you help me with any guide on where I need to check why the PO is not printing immediatelly when i create the PO via ME21N?
kind regards,
Camilla

hello all,
thanks so far for your reply.
i have checked today my user settings and that shows that my prints should go to LOCL (local default printer)
The output conditions fpr purchase order have also LOCL (local printer)
The weird thing is that I can print other reports to the default printer without any issues. The issue arise when I create a purchase order via ME21N. Normally when I save the PO it automatically prints. So no manual print instructions are required from my side. Because if I give manual instructions then I'm able to print the purchase order.
Is it possible that the automatic printing is switched off and that it only prints when I hit manually the print button?
Is the automatic printing something that is maintained in SPAD?
kind regards and thanks for your help sofar

Issue with printing production order after changes through CO02

Hi,
Currently I have one issue with printing production order changes through CO02. If I go for print, all the operations are captured in printout. But after the print, if I add any new operations to this production order, and then go for print, its not capturing the newly added operations. Also, there is information popup coming "Copies will be printed for order. Original list already printed". This message effectively means, even after changes, when I go for print functionality, its just going for printing copies of original printed list.
Can anyone help me out to get the newly added operations reflected in the print through CO02 ?
Regards,
Shiva

Hi Shiva,
Refer SAP note 28887.
Source: http://www.sapfans.com/forums/viewtopic.php?f=9&t=308577
Please search /google before posting queries.
Regards,
SuryaD.

Issue with printing newly added operations in Production Order through CO02

Hi,
Currently I have one issue with printing production order changes through CO02. If I go for print, all the operations are captured in printout. But after the print, if I add any new operations to this production order, and then go for print, its not capturing the newly added operations. Also, there is information popup coming "Copies will be printed for order. Original list already printed". This message effectively means, even after changes, when I go for print functionality, its just going for printing copies of original printed list.
Can anyone help me out to get the newly added operations reflected in the print through CO02 ?
Regards,
Shiva

Hi,
1) Go to Tcode "OPK8"
2)Select LG02 "Op Control Ticket"
3) Double click on :List Control for Transactions" in the left hand menu tree
4) In front of ur desired t code "co02" make the changes ( Number of prints- u can increase) 6th column.
Try this.

Issue with print image in air

hey frnd,
plz check this link
http://livedocs.adobe.com/flex/3/html/help.html?content=printing_5.html
hey frnds,
while using this multiple print datagrid code, getting 1 issue with
print image in printheader mxml file.
I'm adding 1 image tag and runtime getting image path in variable and
want to print tht image in header ,
but it is not get printed but if i'm giving @Embed image as a source
then it is print.
Is any way there to print runtime image after adding in printheader
file ?
thx in advanced,
[email protected]

is any solution there ?

Issue with printing of Currency Value.

Hi,
I have an issue with printing of Currency Value.
( Pleae let me know if any thread available already I searched it before posting but not found).
The Problem is as follows:
I have a field s_value TYPE MARM-SALK3. (which is of currency type).
The value of field is actually 1664.1450. Currency USD
But when I print this variable in ALV report it prints as 166414.50 though I used the same data type. (SALK3).
Pleaes help me to fix this.
Regards,
Venkat

Hi,
If you use ALV to display currency value, you must sure that currency amount links with currency unit. You can archive this by using ALV fieldcat:
wa_fieldcat-fieldname = 'SALK3'.
wa_fieldcat-tabname = 'ITAB'.
wa_fieldcat-cfieldname = 'WAERS'.
wa_fieldcat-ctabname = 'ITAB'.
append wa_fieldcat to gt_fieldcat.
Please check,
Regards,

Is anyone having issues with printing to network printers with 10.8.4?

I have upgraded our schools to Mountain Lion. Ever since the beginning of the year we have had issues with network printers. They are all HP printers, when they go to sleep a user has to turn off the printer and turn it back on then resend the print job. Now users are being asked to put a password itno the Print Operator group. This never happened before. Cups is changing the queue names to MCX_1 or 2 etc. Not keeping the queue name. All these people are in WGM and have printers set for their group. So I have reset the printer settings on the machines, then restart relog in and get the list of printers they can print too and within 1 day they are unable to print. I am trying my very best to get this issue fixed and all solutions have been exausted. So without having to go to every computer and going into the Ldadmin group thru a terminal, is there anything that anyone has done to fix this issue with out visiting every computer. Thank you.

The printers failing to wake from sleep is an issue. A print request should be waking them.
You have not mentioned what printer server is involved. I could assume it is OS X Server since you mentoned WGM, but it would be nice to have you confirm this. Then I can start to suggest some actions.

Issue with printing of Watermarks

OK, what I am trying to do is add a Watermark to a document which will not appear when viewed on screen but will appear when printed.
I am using Adobe Acrobat Professional Version 8 and Vista Business.
I create my Watermark and under the 'Appearance Options' link I have the 'Show when printing' option selected and the 'Show on Screen' option deselected. When I got to File - Print, it shows a small thumbnail of the document which shows the Watermark on it. However, when I then print it to my default printer, there is no watermark on it.
I have tried every option I can see regarding watermarks and am now getting frustrated. If anyone can offer any help it would be most appreciated.
Thanks.

OK, I was able to print it. I first tried it to print to a HPLJ III and got an overflow (typical memory issue with LJ). I then printed 2 pages to sheet with document and markup - it worked with the Uncontrolled watermark. I tried printing to a new PDF with the document and markup - got the watermark. I then printed to a network printer with the same option, but got only the document, not the watermark (I can not explain) -- even though it showed up in the preview.
I think that may be some of what you are finding also. Just for your info, this is VISTA Business, SP2, with AA8.1.6. At least it adds some information to your collection for what is happening. Of course if I select document only, then the watermark does not appear.

Problem with printing over wireless network

Hello. I have a HP psc 2410 all-in-one printer.
I've recently bought a modem router which has a capability called"printer-server" and I decided to use this feature and print over wifi. I set it up but with a problem. when I print something, for instance, test page, instead of printing just one page, It will print "test page" in 3 pages( something like partial pages and which the last=third page is printed blankly) and then It freezes(printer screen shows "printing" and I have to cancel the job, otherwise it freezes and I have to replug it). I have this trouble not just in test page but at least from IE, office, PDF files. This problem is essentially about Wifi, since If I connect the printer directly to the PC or laptop via usb, it works absolutely fine. also I have tried printing with different laptops over wifi but no go. below are more information which I have to mention:
1)Router is on WPA-PSK encryption type.
2)There is no mac-filtering or hiding SSID going on.
3)one laptop and an iPad is connected to router via wifi and a PC which is connected by LAN cable.
4)The printer IP address is the same as Router's settings page IP address.(192.168.0.1)
5)I can't open the printer's internal web page by entering the printer's IP address in browser since it's the same as router IP address.
6)Firewall on my laptop( windows 7 32-bit) is off and I'm using no Anti-virus.
7) I have tried HP PRINT AND SCAN DOCTOR, but it says the printer is OK.
thanks
Leland
EDIT: after investigating for hours, I finally managed to get rid of freezing problem. now there is just one problem of that partial printing which happens coincidentally over wifi! I mean, sometimes it happens and sometimes not!
any suggestions? I'd really appreciate it
This question was solved.
View Solution.

The bottomline is that this printer has no way of connecting other than a straight USB connection. In order to make it wireless you have to have a device that will give it an network IP address. The printer by itself can not do this.
The only way to get this printer on a network is to buy a SEPERATE USB Printer Server. Or, buy a separate router, like I said, that has a USB connection on the back that will support printers.
You can not connect it the way you want as it stands right now.
However, call your ISP and have them set it up IF their Gateway device has a USB connection and really can support a printer. It is their issue.
Say thanks by clicking the Kudos Thumbs Up to the right in the post.
If my post resolved your problem, please mark it as an Accepted Solution ...
I worked for HP but now I'm retired!

LAN issues with printing

I recently purchased the NOVT1114 4G LTE router. It is working great and all the computers connect to the Internet just find. The problem is suddenly we have not been able to print to the networked printer connected to a separate wireless router via an Ethernet cable. I have the wireless router in one building that gets a better 4G signal and some computers connect and receive their IP from the 4G router. I then have connected to the 4G router a wireless Ghost Bridge to connect the other building. At the end of that Ghost Bridge is a wireless router setup for DHCP for those devices. So yes, they receive the internal 10.0 address not for public use. Like I said all those computers connect to the Internet and have great service. The wired networked copier however cannot get out and no one can print to it. We can't seem to see backwards into the LAN from the computers connected to the 4G router either. We use to be able to ping the other router, but I can't seem to get past the 4G router into the LAN like I used to. What am I missing? Ideas?

As I read your description I paint the following topology for your environment:
- VZW ))) 4G Router ))) PC1
- VZW ))) 4G Router ))) PC2
- VZW ))) 4G Router ))) Prt1
- VZW ))) 4G Router === AP2 ))) PC3
- VZW ))) 4G Router === AP2 ))) PC4
- VZW ))) 4G Router ))) AP3 === AP4? ))) PC5
- VZW ))) 4G Router ))) AP3 === AP4? ))) PC6
Apparently all PCs have internet access which is a good start. At least the networking devices are talking to each other and handing traffic down the chain and back out to your 4G LTE router which is acting like the modem/WAN connection.
If I'm following you correctly then PC1 and PC2 cannot ping PC5 and PC6. Likewise nothing can apparently connect to Prt1 (network printer). I feel a few issues could be going on.
1. Double NAT - Depending on how you have configured your additional APs (access points) you may have devices sitting behind multiple NAT firewalls within the LAN. That means traffic can leave devices like PC6 and hit the internet but not necessarily the other way around unless those devices opened up a pathway first. Not to mention the NAT you are resting behind on the VZW network itself...
2. Wireless Client Isolation - Its common for many home routers to have a feature that limits the ability of locally connected machines from communicating directly with each other. This feature is often desirable for guest wireless access and not so much for home/personal use.
What you should consider doing is temporarily disabling all of the DHCP functionality on your additional APs (the bridge and 2nd router). Allow all devices to rely on the 4G LTE router as the default gateway and DHCP server. That way everything can be managed together as one large network instead of several smaller isolated ones.
To help with the printer issue consider temporarily Ethernet cable connecting it to the router its nearest to and then having wireless devices on the same router setting up a new connection. This should help you determine if any kind of wireless isolation feature is enabled or not. It shouldn't be by default but you may have accidentally turned it on somehow. Restoring the defaults on the 4G LTE router would also clear up an issue like this too.

Airport Extreme issue with printer

I recently switched to an Airport Extreme to replace my linksys router. Since then, I am no longer able to find my Epson Artisan 810 printer when I try to install it. (I'd been printing with it for about a year prior). My PC has no problem with printing and all of my devices are able to find the wireless signal with no issues. I also added OS X Lion at the same time. Now I am unable to print through my Macbook Pro. Has anyone had similar issues and found a solution. Thank you!!

I just spent several hours linking an Epson Workforce 600 printer to a new Airport Extreme network. On the printer, I reset the printer to its original settings. It was then recognized by the Epson setup software program.

Issue with Print Properties button not responding in Adobe Reader 10.1.10

We've recently been upgrading Adobe Reader 9.4.4 to 10.1.10 and started having a few reports of the Print -> Properties box in Adobe Reader not responding. When this happens Adobe Reader will crash if you click on the Print button. If you go into Devices and Printers and try and access the Printer Properties you are prompted to install the driver for the device. It does seem to be quite random, it will work fine for days and the suddenly happen. I've done testing and have been able to get it happen by opening Outlook, Word or Excel but it is completely hit and miss. Sometimes the issue will happen and other times no matter how many times you open and close the various applications it's fine.
Fortunately it only seems to be an issue when accessing Properties, if you just print there are no options which is probably why we don't have more complaints. Unfortunately this didn't come to light until we'd rolled it out to 2000+ machines across 8 locations.
So far I've tried the following:
1. Upgraded to Adobe Reader 11.0.9 and same issue
2. Created a test print queue using a different print driver (my machine has a different driver again and is using a different print server)
3. Uninstalled a number of applications that have caused us issues with Office 2010 due to dodgy addins (Workshare and HP Filesite)
4. Rolled back to 9.4.4 and seems OK. Problem here is that they receive PDFs in formats not compatible with older than X.
System is Windows 7 Enterprise SP1 32bit, Office Professional 2010, printing is to Ricoh Equitrac (Follow You)
Anyone have a fix for this or come across this before. I'm going to try testing with a Postscript driver to see if that helps, which is the last item on Adobe's troubleshooting list.

Select a PDF file, CMD+I, check the Open With section, and ensure that AR is selected. If not, then select it and click on the Change All button. Alternatively, select Preview, which is my default PDF reader.

LaserJet M1120n MFP - Problems with printing over Wireless Network.

Hi. I have recently purchased a HP M1120n MFP printer. There are three wireless laptops (Vista, & XP Pro) that use this printer via a DrayTek Vigor 27000GE wireless router, then via cat 5 cable to Ethernet on printer.
All three laptops can print, but sometimes the print queue backs ups. The top print job will say "Printing" but it can say this for hours! Then if I delete the print job, it will say "Deleting" - but nothing happens. The only way to clear it is to reboot the laptop.
Firmware datecode is 20080228.
If I connect via USB cable directly to the printer it works correctly.
Any ideas to help resolve this frustrating problem?

The bottomline is that this printer has no way of connecting other than a straight USB connection. In order to make it wireless you have to have a device that will give it an network IP address. The printer by itself can not do this.
The only way to get this printer on a network is to buy a SEPERATE USB Printer Server. Or, buy a separate router, like I said, that has a USB connection on the back that will support printers.
You can not connect it the way you want as it stands right now.
However, call your ISP and have them set it up IF their Gateway device has a USB connection and really can support a printer. It is their issue.
Say thanks by clicking the Kudos Thumbs Up to the right in the post.
If my post resolved your problem, please mark it as an Accepted Solution ...
I worked for HP but now I'm retired!

Issue with printing Indesign exported PDF in Chrome

I have created a file in CS6 and exported it to a two sided PDF. This PDF works when printing from the PDF.
I have uploaded it as a document link on a website and when clicking on the link it opens in a separate window. If people use Internet Explorer or download the file the PDF and print it it looks perfect.
If the user is using Google Chrome only a section of the PDF prints at a large size. It looks like it thinks the PDF is an A3 so only prints the bottom left hand corner.
Things I have already tried - which all have the same issue.
Creating a brand new InDesign file and exporting reuploaded on the website
Saving it as a IDML file and exporting and reuploaded on the website
Had someone else export the file
Tried printing from google chrome outside the office
Checked no issues with the website backend
Checked with the IT company that services our systems.
Thanks in advance of your help.

Hi jtrew,
It sounds as though the issue is specific to Chrome. Please see the following document from Google support: https://support.google.com/chrome/answer/142056?hl=en
Let us know how it goes.
Best,
Sara

Issue with printing to a network photocopier

Similar Messages

Maybe you are looking for