IviSwitch looses value when sending, "configure switch" configuration = TRUE

Hi all,
we are currently evaluating Teststand 4.1 with a keithley 3706 system switch multimeter.
After a first enthusiasm, thinking this tool together with the switch multimeter fits perfect our needs, real life seems some harder.
Between several other problems, we need to tell the device, that the channel "s1com1" and "s1com2" are configuration channels.
Configuring the teststand step : Edit IVI Switch Step -> IVI switching, Configure Switch : Channels "s1com1", Configuration = True
leads to two actions observable in Ni Spy:
GetAttributeViBoolean(...,"s1com1", _IS_CONFIGURATION_CHANNEL , VI_FALSE)
SetAttributeViBoolean(...,"s1com1", _IS_CONFIGURATION_CHANNEL , VI_FALSE)
manually calling this class functions from an interactive CVI fp works as expected (setting it to VI_TRUE)
Does anybody have any hint what we could do wrong? Currently we are just before writing wrappers in cvi and skipping all the wonderful IVIStep Types in teststand.
Looking forward to any feedback
David Clus
Solved!
Go to Solution.

David -
This might the same problem that we recently discovered in our internal testing. For the problem that we found, we will likely include our fix in an upcoming maintenance release. Can you verify whether the problem still occurs if you change your regional settings to English in the control panel? If the problem no longer occurs, can you use this as a workaround for now?
Message Edited by Scott Richardson on 10-06-2008 10:48 AM
Scott Richardson
National Instruments

Similar Messages

In Ap invoice grid is showing no value when send for approval

Dear Experts,
There are 3-4 purchase invoice send for approval when it is open by approving authority the detail grid i.e. where the item details are shown is blank only gross total and net total in footer is showing value and header values.
This all four invoices are of same vendor, invoices punch after those invoice are showing proper values.
what could be the reason ?
Thanks & regards
Kamlesh

Dear Kamlesh,
If the problem only occur for one BP, check this BP's profile.
What is the condition for approval?
Thanks,
Gordon

Cascaded LOV loose value when pooling disabled

Hi All,
I am using jdev 11.1.1.5
my scenario is i have search VO with transient attributes.Most of attribute are LOV using accessor.
Few of LOV are dependent on each other. When i am running by enabling pooling true.it is working fine.
But when pooling disabled, cascaded LOV are not persisting value in the VO. It is happening only for dependent LOVs . I am not sure why is it so.?
I am creating a new row of Search VO usng Create Method of VO operation.Should i try anything else?
Is anyone faces this issue earlier? any suggestion to handle this. All attribute are passivated and VO have key attribute.
Please suggest?

Hi Frank,
Well all LOV are transient attribute.Problem is this - Everything working with AMPooling enbaled.But when AMPool disabled then only attribute whose value are depend on other LOV are not persist or loose.
Yes they are marked passivate. and i also override afterRollback and beforeRollback in all ViewObjectImpl.java with commenting super call.
Seems , variable are setting by bind variable are not passivated the value. I am not sure, is it some strange behavior or i am doing anything wrong.
What you suggest to investigate further more on this?
Regards
Vinay

MDNS cannot be configured when FlexConnect Local Switching is enabled

I am running Cisco Prime Infrastructu tore 1.3 and I am trying to push a template to allow flexconect local switching on a wlan. However, when I attempt this, I get the message "mDNS cannot be configured when FlexConnect Local Switching is enabled" and I cannot save the template or apply it to controllers. My controllers are WISM 2s running 7.0.235.3.

Make sure you uncheck the mDNS option on the advanced tab of the WLAN template. You cannot use mDNS in conjunction with Flexconnect locally switched WLANs.
Sent from Cisco Technical Support iPhone App

LMS4 user tracking dynamic update switch configuration

So there is a tool that is supposed to configure switches to send mac notification traps:
Admin => Collection Settings => User Tracking => Device Trap Configuration
When I try this on a 3560, 3560X, 2960S or 2960X stack I receive the following message:
Command Not Found - Device trap configuration commands are not found for device(s) <ip address>
I was able to get it to run on a 3550-12G, though it didn't quite get the configuration command right.
Is this tool defunct?
Thanks,
-Jeff

What exact LMS version are you using?
As you said the configuration wasn't right and had incorrect commands on 3550-12G, what was it? Please share the commands configured on it.
You can verify which command LMS should ideally use, from this document :
List of Commands to Enable MAC Notification Traps on Devices
You can check the file MACCommands.XML from NMSROOT/campus/etc/cwsi/ from where LMS picks the MAC commands.
You can share this file and also check yourself if it has the correct commands as per the device sysObjectID.
If the device and its sysObjectID has missing entry, it may have the error coming as null.
-Thanks
Vinod

Sender Mail Adapter Configuration error

Hi,
I am working on scenario mail adapter to CRM system. And when I tried to configure the sender email adapter I have got the error following error, Can any one help me to resolve this issues
error occured: <b>exception caught during processing mail message; java.net.ConnectException: Connection refused</b>
the details I have provided are as follows
Transport protocol is POP3
URL - POP://mailservername/Inbox/folder
And I have tried with the IMAP4 also
URL - IMAP://mailservername/Inbox/folder
And we have cross checked that the XI server is able to ping that particular mail server.
Regards,
Venkat.

Hi Venkateswara,
I would suggest that you go through these to know how to configure your sender mail adapter,
<a href="/people/michal.krawczyk2/blog/2005/12/18/xi-sender-mail-adapter--payloadswapbean--step-by-step mail adapter step by step</a>
<a href="/people/prasad.ulagappan2/blog/2005/06/07/mail-adapter-scenarios-150-sap-exchange-infrastructure adapter Scenario</a>
Also, to know the various parameters of a sender mail adapter, just go through this link,
<a href="http://help.sap.com/saphelp_nw04/helpdata/en/23/c093409c663228e10000000a1550b0/content.htm">Configuring sender mail adapter</a>
Check your mail adapter configuration against these details. Also, check if the mail server you are trying to access is running.
Also go thru this pdf to make yourself more comfortable with mail adapters.
https://websmp205.sap-ag.de/~sapidb/011000358700004556712005E/HowTo_Mail_Adapter2.pdf
Regards,
abhy

SG500X 10GE uplink configure switch port access

Hi,
Can I configure the 10GE uplink interface of the SG500X as switcport access?
Partner is asking if a server with 10GE interface can be connected to the 10GE uplink of the SG500X.
Mark J.

I think the speed of the interface does not matter when you want to configure access or trunk. It is always possible whatever speed that interface might be
One thing your customer want to consider is if the compatibility between the module of the server and the switch.

Invalid switch configuration-oob error

Hi all,
We are using NAC in OOB Virtual Gateway mode only for wireless users.But we are facing an error on user PC stating that,
    invalid switch configuration-OOB error:OOB client MAC ADD/IP ADD not
                   found. Please contact your network administrator.
              Please contact your administrator if the problem persists.
Thanks in advance.

Please check your snmp settings on the wlc and the manager. This is usually seen when the agent passes the mac address and clients ip address to the CAS but the CAM never receives the mac notification trap.
thanks,
Tarik

SG/SF 300 switch configuration change in behaviour

Since upgrading the small business switches from the initial factory shipped image(1.0.0.27) to 1.1.1.8 or 1.1.2.0 we are seeing a failure of our config file being completely loaded. We have a manangement ip on vlan 99 which fails to take when you load the configuration thru HTTP/HTTPS interface. Cisco small business TAC states that the switch has to be switched to layer 3 mode in order for this config to be accepted.
If you manually paste the config via cli the config will take. Problem being is you are prompted at 2 points to enter yes during the input. The switch mode stays layer 2.
This was working previous to 1.1.1.8. If I have my template config loaded and I upgrade to 1.1.1.8 vlan 99 ip is working. The probem is when you get a unit from the factory that has 1.1.1.8 or 1.1.2.0 you have to jump thru hoops to get the template to work.
Our field techs use the http interface to upload the template config. This is broken and adds additional time to there install.
I am requesting some type of fix to allow me to use http to upload the config that uses a management ip on a different vlan and not have to switch to mode to layer 3.
Bottom line is uploading a config should not be this difficult and it was functional before the image upgrade to 1.1.1.8.

Hi Mr, to try to fix this, you can have the switch doing DHCP for you on the latest firmware.
On my switch I have vlan 1 and 2 vlan. I set up DHCP to service through my vlan 2.
My vlan 1 is 192.168.100.129
My vlan 2 is 192.168.2.254
config t
vlan database
vlan 2
int vlan 1
ipaddress 192.168.100.129 /24
int vlan 2
ip address 192.168.2.254 /24
ip dhcp server
ip dhcp pool network vlan 2
address low 192.168.2.10 high 192.168.2.50 255.255.255.0
lease infinite <-- make the least time to not expire
default-router 192.168.2.254 <--- specifies the vlan 2 SVI as the gateway
dns-server 8.8.8.8 <-- I chose random DNS
You can set up dhcp pools for every vlan and have the switch assign the connecting clients the IP within the SVI they connect to. Then to make the modem work you will need a static route pointing back to the switch to be able to route the traffic.
If you need a visual effect for a router that doesn't support vlans please look at this topic-
https://supportforums.cisco.com/thread/2123434
-Tom
Please mark answered for helpful posts

"Server either does not have a virtual switch configured or none of the configured virtual switches have an IP address assigned" error driving me nuts!

OK; have been trying to setup a test VM based RDS deployment for a few days now with no luck.
this error mentioned above:
"Server <server name> either does not have a virtual switch configured or none of the configured virtual switches have an IP address assigned" error is driving me nuts!
I have removed and re-added the RD Virtualization Host role numerous times, each time having the "create a virtual switch" checkbox selected, but it did NOT create any virtual switch.
I created the external virtual switch manually and tried to create the desktop collection again, no luck with the same error.
a few questions:
1. you don't assign IP to a switch! you assign IP to Network Interfaces. why does the error puts it like this?! it is technically wrong.(yeah yeah I know all about how you'd assign IP to managed switches in real world to telnet into them and manage them.
you know better than me that it is not the case here!)
2.the RDS Virtualization hosts are using their wifi card as the card for the virtual switch. could that be the reason? I even disabled their unplugged wired NIC just to make sure that the wifi is the only available option for the RDS wizard to use for the
virtual switch creation; but it didn't use it and it didn't create any virtual switch automatically.
3.if WIFI nic is indeed the reason, is it your suspension or an official documents is there somewhere stating so (that the WIFI NICS on a Virtualization hosts are not supported as the hub for a virtual switch).
4.what are the properties of the virtual switch the RDS requires? does it have to be external? why can't it work even with my manually created external switch?
5.how would I fix it?
P.S: the environment is made up of 2 laptops, having windows 2012 R2 trial installed on them, using their wifi to connect to the out world. no cable is plugged into their wired NIC card.

Hi,
Thank you for posting in Windows Server Forum.
The simplest short term solution was to connect each computer to a small switch that had no other connectivity. This brought up the link light on the external NIC and allowed the creation of the collection to complete. You need to use an external switch. You
can create one external switch which might fix the problem.
Please check below article for information.
VDI Deployment Error About Virtual Switch
In addition please referthis article for information regarding virtual switch.
Hope it helps!
Thanks.
Dharmesh Solanki
TechNet Community Support

Sender JMS adapter configuration for IBM MQSeries

Dear All,
i am doing a IBM MQSeries 5.2.x Message ->sender JMS adapter -> XI server -> receiver RFC adapter -> R/3.
i have deployed the JMS adapter with the required jar files of IBM MQSeries 5.2.x in XI server.
in Sender JMS adapter configuration for IBM MQSeries 5.2.x, i have put following data:
1. Transport Protocol: Websphere MQ - is it okay?
in JMS provider settings:
2. in channel name - what should be there?
3. Transport Network protocol should be TCP/IP or WebsphereMQ - how to decide this thing.
4. JMS Complaint - whether WebsphereMQ or JMS API.
in JMS Settings:
5. JMS Queue user - is this IBM MQSeries 5.2.x Queue User or someother user?
6. JMS Message Selector - what data to take here.
So if anybody has connected IBM MQSeries 5.2.x to XI via JMS adapter, please answer my above queries.
Regards,
Rajeev Gupta

Hi Swaroop,
you can send me those documents at my gmail-id : [email protected]
Hi All,
one more question - to connect XI server to IBM MQSeries via JMS adapter in ID, do we need to have a MQSeries Client installed on XI server - or - just by configuring JMS adapter, we can send messages from IBM MQSeries to XI server without any MQSeries client on XI server?
Why Channel name is required in JMS configuration data?
Thanks,
Rajeev Gupta

Mail app crashes when I try to configure my Exchange account

Just bought a Sim free iPhone 6, 16 GB (A1586). Successfully configured the Mail app with my Gmail account. However when I try to configure my company's Exchange account, the mail app crashes.
Reset the network settings, but the app crashes upon verifying the credentials for exchange account.
Just updated my phone to iOS 8.1.3 but the Mail app still crashes.

Hi KingMak,
This is not an issue with your credentials for the exchange server, as that would give you an error when trying to log in rather than completely crashing. The issue with the app crashing indicates a software issue with the phone -- potentially a corrupt file within the iOS installation itself. You're on the right track by updating your operating system and resetting settings, but these will not necessarily repair a corrupt file. I would recommend backing up your phone to iTunes or iCloud and then using iTunes on a computer to completely reinstall the iOS software. This will erase EVERYTHING off of the phone (including the corrupt file) and then install a fresh, clean copy of iOS 8.1.3. Let us know if you're still having issues after that!
Good luck!

Round badi does not work in default formulas triggered when sending a value

I have implemented the round BADI from sdn (how to). Problem is that it works perfect when :
- I execute it in UKT
- I run it as a data manager package
- I put it in default formulas and run the default formulas as a packe
It however doesn't work when it is executed in default formulas when sending a value from an input scheduls.It gives an error "error converting records - the root element is missing"
Anybody a clue ?
Cheers
Nico

Answering to myself!
Code correction required:
loop at it_cv into ls_cv.
*{ INSERT BPCK900005 2
CHECK ls_cv-dimension NE 'MEASURES'.
*} INSERT

Switch configuration for AP's

We are trying to install a 2106 controller with a few 1261 AP's which we have downgraded to Lightweight.
We are getting our head around the 2106 config but am unsure as to what config to put on the switchport the AP's connect to.
As far as our reading goes it is best practice to plug the AP's into a network swtich and trunk vlan's from the switch to the controller.
Bit confused about the way the AP's connect to the switch.
Thanks
Roger

Hi,
As I understood ... you need to map existing vlan subnet with your wlan ...
you will have interfaces which you first need to configure on your controller .
1) Management IP of wlc
2) AP- manager
3) dynamic interface which will be used to map the vlan with respective wlan
4) virtual
procedure :
1) if you do not have dhcp seperate configured , first you need to create vlan then configure svi interface with ip address and dhcp pool for your ap to get ip address in your l3 switch which is connected to your controller with default-router command which will point to your switch
2) login to your controller through console and configure the management IP address
command : WLC( config ) > interface address management ... ip address... mask .... gateway ( it will be your switch )
configure AP-manager interface with above command with ap manager option ..
Now switch side you configure the one port which is connected to your controller as a TRUNK
connect ap to any port which will configured with above vlan which you have configured in l3 switch
Now AP should get registered and then follow below procedure for getting client connected to respective WLAN
3 ) once you configure login to gui of controller and configure dynamic interface with existing vlan subnet and give the dhcp server ip address if you have or else configure the dhcp pool for users also.
4) go to " wireless " option
5) select the respective wlan and map the vlan with respective dynamic interface
check whether clients got ip address.
please let me know ........ if you have doubt about it

Fail when config "Internet Directory Configuration Assistant"

I install oracle9ias( Infrastructure ) in AIX4.3.3 .
It failed when config "Internet Directory Configuration Assistant"
error message:
No output aviaible for this tool

the solution is
1- I removed the Network cable
2- I formatted the server
3- I Installed the Application Server
4- I Connected the server with network and I gave a static IP to the server
Best of Luck
Edited by: user13011851 on Jan 11, 2011 2:40 AM

IviSwitch looses value when sending, "configure switch" configuration = TRUE

Similar Messages

Maybe you are looking for