Jumbo frame caveat on 3750 - dynamic arp inspection

i want to enable jumbo frame on a stacked 3750 running 12.2.25(SEB2).
any caveats - the only caveat i found is dynamic arp inspection.

Hello,
There is no know problem with Jumbo/Giant frame support on 3750 platform other than the bug you reported.
I have verified that Jumbo/Giant frame support works on 12.2(25)SED in stack configuration.
Facts
- The 12.2(25)SEB2 release has been deferred. Cisco advises you to upgrade to to (at least) 12.2(25)SEB3.
http://www.cisco.com/cgi-bin/Software/Iosplanner/Planner-tool/printdefer.pl?platform=CAT3750&majorRel=12.2&release=12.2.25-SEB2&data_from=&file=12.2.25-SEB2.CAT3750.c.html
- Jumbo/Giant frame support
http://www.cisco.com/en/US/products/hw/switches/ps700/products_configuration_example09186a008010edab.shtml#3750
HTH

Similar Messages

  • Dynamic ARP Inspections on Wifi Routers?

    Is Dynamic ARP inspection possible to be done on wifi routers? I'm asking because I can't find any model with that feature. I would especially be interested in some cheaper models for home or small business use (maybe Linksys).

    You could be better served posting this on the SOHO forum. Speaking to enterprise gear like the cisco WLC yes.
    DAI for Wireless Access
    The WLC protects against MIM attacks by performing a similar function as DAI on the WLC itself. DAI should not be enabled on the access switch for those VLANs connecting directly to the WLCs because the WLC uses GARP to support Layer 3 client roaming.
    It is possible to enable DAI for each VLAN configured on a trunk between a FlexConnect and access point. Therefore, DAI is useful in wireless deployments where multiple SSIDs/VLANs exist on an FlexConnect. However, in an FlexConnect WLC deployment, there are two topologies that impact the effectiveness of the DAI feature. Both topologies assume that the attacker is associated to a FlexConnect WLC and is Layer 2-adjacent to the targets:
    http://www.cisco.com/c/en/us/td/docs/solutions/Enterprise/Mobility/emob73dg/emob73/ch4_Secu.html#pgfId-1019449

  • Help understanding DHCP Snooping and Dynamic ARP Inspection

    Please help me to understand DHCP Snooping and Dynamic ARP Inspection.

    HI Ezra,
    In simple words:
    DHCP Snooping is a feature which is available on switches. This feature is used to prevent rogue dhcp server attacks.
    In the diagram, a valid dhcp server is connected to the network. The computers are suppose to receive dynamic ip addresses from the valid server. An attacker implants a rogue dhcp server on the network as shown in the diagram. The following steps are followed for a client to receive an ip address from a dhcp server.
    When a client (computer) is connected to the switch and is configured to receive a dynamic ip address from a dhcp server, the dhcp service on the client, sends out a DHCP Discover packet, searching for servers on the network. This packet is broadcast in nature. DHCP servers on the network, would respond to the DHCP Discover packet sent from the client. In the example, both the DHCP servers would respond to the DHCP discover packet. The client would process the first packet it receives. If the response send by the rogue dhcp server reaches the client first, then the computer would have an ip address provided by the rogue dhcp server.
    To prevent this, dhcp snooping is configured on the port on which the valid dhcp server is connected to. After the configuration is performed, no other ports on the switch would be able to respond to DHCP Discover packets from the clients. So even through the attacker has set up a rogue dhcp server, the port on the switch to which the attacker has connected would not be allowed to respond to DHCP discover packets. Thus dhcp snooping thwarts the attempt from the attacker in setting up a rogue dhcp server.
    DAI:
    Please read the expalined version from here: http://ciscocertstudyblog.blogspot.de/2010/06/ciscoblogpics.html
    More about DHCP snooping and DAI: Please read this attached document with some detailed explanation.
    Hope it helps.
    Regards
    Please use rating system and mark athe question answered it may help others.

  • Sg200-50 support dhcp snooping and dynamic arp inspection?

    do the sg200-50 switches support:
    dhcp snooping
    dynamic arp inspection
    ?? thanks

    HI d.pennington,
    SG200 is L2 switch only.  so this mean switch not support dhcp snooping.  Switch support IGMP snooping, Switch support dynamic arp table.  You can management switch with web page GUI only (CLI) not supported.
    Thanks,
    Moh

  • Dynamic ARP inspection rate limit issues with Windows Vista Systems

    Good Day to everybody.
    I had implemented DHCP Snooping & Dynamic ARP inspection feature to mitigate ARP spoofing attacks to one of customer location where we have mix of Windows vista & XP systems. By default DAI feature rate limit ARP packets on un-trusted ports to 15 Packets per second. With this value I was facing some issue to access file shares where port will go in error-disabled state due to ARP broadcast from system was crossing 15 PPS limit of DAI. For the same, I had increased the DAI limit to 64 & after that we had not facing this problem from windows XP systems, but windows vista systems are still giving problem. Also this probem is very random in nature & not all the windows Vista system will face same issue even though they are accessing same file share & are configured with same DAI rate limit.
    That's why I am not able to figure out baseline values for DAI rate limits. I had already search microsoft documentation for limiting this ARP broadcast from Windows Vista system, but no luck.
    Is there any way to find out correct settings for this DAI packet rate limiting in Windows Vista enviorement ?

    Hello bensyseng,
    check out this thread.
    As topmahof said already it could correlate with a wrong Intel driver.
    Follow @LenovoForums on Twitter! Try the forum search, before first posting: Forum Search Option
    Please insert your type, model (not S/N) number and used OS in your posts.
    I´m a volunteer here using New X1 Carbon, ThinkPad Yoga, Yoga 11s, Yoga 13, T430s,T510, X220t, IdeaCentre B540.
    TIP: If your computer runs satisfactorily now, it may not be necessary to update the system.
     English Community       Deutsche Community       Comunidad en Español

  • Do sg200-50 support dhcp snooping or dynamic arp inspection (DAI) ?

    do the sg200-50 switches support:
    dhcp snooping
    dynamic arp inspection
    ?? thanks

    HI d.pennington,
    SG200 is L2 switch only.  so this mean switch not support dhcp snooping.  Switch support IGMP snooping, Switch support dynamic arp table.  You can management switch with web page GUI only (CLI) not supported.
    Thanks,
    Moh

  • How config dynamic arp inspection for 300 or 500 series ?

    Hi Cisco Expert ,
    How config dynamic arp inspection for 300 or 500 series ? Do you have clearly document for this solution ? Could you please to share ?
    i find in admin guide it's no simple to do
    Thank you for kindly support.

    Hi Siriphan, using the command line is the easiest way to deal with this.
    You need to understand the difference between trusted  and untrusted interfaces. The untrusted interfaces are the ports that  will be inspected and if not specified within the arp entry list then  will get dropped.
    Any port you do not want arp inspection to be a part of, you need to trust that port.
    Below is how to make a port trusted.
    configure terminal
    interface fe1
    ip arp inspection trust
    Once you establish the trusted ports, you can build your arp list.
    configure terminal
    ip ap inspection list create ARP_INSPECTION  (the word after the create can be anything you want)
    ip 192.168.100.3 mac-address 64:31:50:1c:50:a1
    This  is the example of adding 1 entry to your arp list. You can add128 of  these entries. These IP/mac binds are the devices that are "safe" from  being dropped.
    Lastly, you need to enable the arp  inspection globally. You DO NOT want to toggle the arp inspection  without establishing your interfaces or bind list. If you do not  establish your trust interfaces and list first, you will lock down any  connection through the switch and essentially brick it.
    To toggle the global arp inspection
    configure terminal
    ip arp inspection
    Once you're done, save your running config to the start up config.
    -Tom
    Please mark answered for helpful posts

  • Dynamic ARP Inspection (DAI)

    Can someone point me to step-by-step configuration guide of how to enable DAI on Cisco Catalyst 6500 Series Switches.
    Thanks

    HI d.pennington,
    SG200 is L2 switch only.  so this mean switch not support dhcp snooping.  Switch support IGMP snooping, Switch support dynamic arp table.  You can management switch with web page GUI only (CLI) not supported.
    Thanks,
    Moh

  • Catalyst 3750 and jumbo frames

    We're looking to implement a gigabit segment with a 3750 switch, with the latest apple imac G5 clients connected and and an xserve G5 connected doing link aggregation using a 4 port smalltree NIC.
    Although the Xserve supports jumbo frames i believe the imac NICs DON'T support jumbo frames although the operating system does( the imac NICs DO support 1000T ) Ideally we'd want the 3750 switch to be configured for Jumbo frames. The 3750 switch we've chosen has all ports of 10/100/1000T with the SMI, so all ports will have the MTU set at 9000 if we enable jumbo.
    Although the Xserve will be fine, i'm worried about traffic that ingresses from the xserve and egresses out to a 10/100/1000 port to which an imac is connected which i believe does not support Jumbo frames. What are the issues in terms of connectivity and dropped packets for an imac G5 connected to a 3750 ?
    seeing as the MTU is set globally and all our ports are gigabit, and machines will be connected to these ports that don't support jumbo but are advertised as having 'gigabit capability'
    Sorry if these sounds like an incoherent rant, but i needed to provide as much info as possible. Help much appreciated

    just to add, in comparison HP gigabit switches can do jumbo vlan on a per vlan and per port basis it's a shame the 3750 can't do that

  • Ip arp inspection limit rate

                     Hi we have configured arp packet limit is 60 packets per second but we are receiving more than 60 arp packets on port and result in to port went to error disable mode.
    config t
    int G1/0/1
    ip arp inspection limit rate 60
    Can somone know what is reason behind more than 60 arp packets within one second on user port

    I believe you also need to enable dynamic arp inspection globally for the vlan that you want to limit on, or this command doesn't work. It's like putting in all of the commands for port security; they don't do anything unless you enable port security on the port.
    HTH,
    John
    *** Please rate all useful posts ***

  • Arp inspection not working on ASA

    Folks,
    I configured a transparent firewall on ASA. I have arp inspection enabled, with dynamic mac learning and dynamic arp. I am able to ping through the transparent firewall using 2 routers with the same mac-address. The firewall shows me that it is learning both the mac-addresses and also forwarding packets, can someone help me understand why this is happening?

    For some reason it will not take the shun command...I've tried every combanation I could think of but it will always fail.. I'm guessing there is a bug or that its just not allowed in transparent mode.. 
    You have to use the vlan before the number or it says invalid host.. when I do specify the vlan 2 it take it and then comes back with "Invalid vlan (2) shun failed

  • Jumbo frame ethernet

    I came across a number of articles relating to jumbo frame gigabit ethernet and integrating into existing networks with fastethernet and 1518 frame size gigabit ethernet devices. Heres a quote i'd like to discuss...
    "Today, however, applications optimized for large frame sizes can easily be integrated with existing Ethernet LANs without causing interoperability problems. For example, you can partition a logical network in which systems can exchange Jumbo Frames and mark them with IEEE 802.1Q virtual LAN tags. The extended frames will be transparent to the rest of the network.
    Adapters that implement IEEE 802.1Q can support different Ethernet frame sizes for different logical network interfaces. For example, a server could communicate with another server using Jumbo Frames while communicating with clients sitting on another VLAN or IP subnet using standard Ethernet frames - all via the same physical connection."
    The use of VLANs to ease interoperability issues is discussed in numerous articles and papers on jumbo ethernet - however, can someone pls explain why cisco have and the implications of the design decision they have taken with the 3750 switches to have no flexibility with configuring jumbo frame support, It can't be assigned on port-by-port basis, nor even on a VLAN basis but is set system wide so on a 24 port 10/100/1000 switch all ports are configured as jumbo regardless of what the connected client devices support.
    Are there any plans to upgrade the IOS to support configuring jumbo frames on per VLAN basis. Jumbo frames are an important issue to us as we can benefit from the performance increases and the improved server CPU utilization. Any thoughts ?

    Best practice here is to segment your Jumbo Frame servers on their own VLANs for Jumbo supported systems only.
    As a post here has already mentioned, Path MTU discovery will tell the systems on the Jumbo VLANs to keep the frames under 1500 when talking to a non-Jumbo VLAN.
    http://www.cisco.com/univercd/cc/td/doc/product/lan/cat2970/12225see/scg/swint.htm#wp1154596
    Please rate all helpful posts.
    Brad

  • *****Jumbo frame on colapse core****

    Hi Folks,
    I have been thinking and research about for that a while now, and yet i have not gotten a formal answer... Please read carefully...
    We are a medium size company.... In both our our remotes, we have four 3750G(two of them are 3750X) in a stack. All good there, the nightmare is we have everything single thing(pc,printer,phones,ipcam,servers(running esxi),SAN(storageFlex)) connected to the stack;therefore, the stack switches are acting as core,distribution and access layer at the same time.
    I need to enable jumbo frame to speed up back, isci frame between SAN and ESXi hosts. knowing i can only enable jumbo frame globally. Since i have all these devices connected to the stack which aren't supported jumbo! should i go head enable jumbo on the stack? Will the device which aren't support jumbo frame will continue to work? Or since i know interface with 100Mb and less will ignore jumbo, should i set all device for which i don't jumbo frame to 100Mb?
    Any help and suggestion will be greatly appreciate.
    Thanks,

    Disclaimer
    The Author of this posting offers the information contained within this posting without consideration and with the reader's understanding that there's no implied or expressed suitability or fitness for any purpose. Information provided is for informational purposes only and should not be construed as rendering professional advice of any kind. Usage of this posting's information is solely at reader's own risk.
    Liability Disclaimer
    In no event shall Author be liable for any damages whatsoever (including, without limitation, damages for loss of use, data or profit) arising out of the use or inability to use the posting's information even if Author has been advised of the possibility of such damage.
    Posting
    A device that doesn't support jumbo on a port that does, will work fine as long as another device doesn't send it a jumbo frame.  If that happens, the device will be unable to process the received jumbo frame.  (I.e. a jumbo enabled switch can allow MTU mismatch between hosts.)
    (If you're thinking about IP fragmentation, that will only happen across a L3 hop, and it often creates additional performance issues.)
    BTW, on the 3750 series, data transfer performance problems are often caused by default 3750 buffer allocations.  Allowing jumbo doesn't address that.  I.e., you might obtain much be better data transfer performance via buffer tuning.

  • %PM-4-ERR_RECOVER: Attempting to recover from arp-inspection err-disable state on Gi2/0/40

    Hi All,
    I am getting below error in the Switch, Please help how to troubleshoot and stop.
    Mar 11 09:46:07.492 GMT: %PM-4-ERR_DISABLE: arp-inspection error detected on Gi2/0/37, putting Gi2/0/37 in err-disable state (C29NEWM434-03-2)
    Mar 11 09:49:07.516 GMT: %PM-4-ERR_RECOVER: Attempting to recover from arp-inspection err-disable state on Gi2/0/37 (C29NEWM434-03-2)
    Mar 11 10:02:55.308 GMT: %PM-4-ERR_DISABLE: arp-inspection error detected on Gi2/0/37, putting Gi2/0/37 in err-disable state (C29NEWM434-03-2)
    Mar 11 10:05:55.325 GMT: %PM-4-ERR_RECOVER: Attempting to recover from arp-inspection err-disable state on Gi2/0/37 (C29NEWM434-03-2)
    Mar 11 10:11:39.306 GMT: %PM-4-ERR_DISABLE: arp-inspection error detected on Gi2/0/37, putting Gi2/0/37 in err-disable state (C29NEWM434-03-2)
    Mar 11 10:14:39.323 GMT: %PM-4-ERR_RECOVER: Attempting to recover from arp-inspection err-disable state on Gi2/0/37 (C29NEWM434-03-2)
    Mar 11 10:50:13.152 GMT: %PM-4-ERR_DISABLE: arp-inspection error detected on Gi2/0/37, putting Gi2/0/37 in err-disable state (C29NEWM434-03-2)
    Mar 11 10:53:13.162 GMT: %PM-4-ERR_RECOVER: Attempting to recover from arp-inspection err-disable state on Gi2/0/37 (C29NEWM434-03-2)
    Mar 11 14:53:30.262 GMT: %PM-4-ERR_DISABLE: arp-inspection error detected on Gi2/0/40, putting Gi2/0/40 in err-disable state (C29NEWM434-03-2)
    Mar 11 14:56:30.279 GMT: %PM-4-ERR_RECOVER: Attempting to recover from arp-inspection err-disable state on Gi2/0/40 (C29NEWM434-03-2)
    Mar 11 15:33:03.207 GMT: %PM-4-ERR_DISABLE: arp-inspection error detected on Gi2/0/40, putting Gi2/0/40 in err-disable state (C29NEWM434-03-2)
    Mar 11 15:36:03.227 GMT: %PM-4-ERR_RECOVER: Attempting to recover from arp-inspection err-disable state on Gi2/0/40 (C29NEWM434-03-2)
    Mar 11 15:46:03.250 GMT: %PM-4-ERR_DISABLE: arp-inspection error detected on Gi2/0/40, putting Gi2/0/40 in err-disable state (C29NEWM434-03-2)
    Mar 11 15:49:03.268 GMT: %PM-4-ERR_RECOVER: Attempting to recover from arp-inspection err-disable state on Gi2/0/40 (C29NEWM434-03-2)
    Mar 11 15:53:23.050 GMT: %PM-4-ERR_DISABLE: arp-inspection error detected on Gi2/0/40, putting Gi2/0/40 in err-disable state (C29NEWM434-03-2)
    Mar 11 15:56:23.064 GMT: %PM-4-ERR_RECOVER: Attempting to recover from arp-inspection err-disable state on Gi2/0/40 (C29NEWM434-03-2)
    Mar 11 17:09:43.703 GMT: %PM-4-ERR_DISABLE: arp-inspection error detected on Gi2/0/40, putting Gi2/0/40 in err-disable state (C29NEWM434-03-2)
    Mar 12 09:53:20.747 GMT: %PM-4-ERR_DISABLE: arp-inspection error detected on Gi2/0/40, putting Gi2/0/40 in err-disable state (C29NEWM434-03-2)
    Thanks in advance,
    Nagasheshu.

    sh errdisable recovery
    ErrDisable Reason            Timer Status
    arp-inspection               Enabled
    bpduguard                    Enabled
    channel-misconfig (STP)      Disabled
    dhcp-rate-limit              Disabled
    dtp-flap                     Disabled
    gbic-invalid                 Disabled
    inline-power                 Disabled
    link-flap                    Enabled
    mac-limit                    Disabled
    loopback                     Disabled
    pagp-flap                    Disabled
    port-mode-failure            Disabled
    pppoe-ia-rate-limit          Disabled
    psecure-violation            Disabled
    security-violation           Disabled
    sfp-config-mismatch          Disabled
    small-frame                  Disabled
    storm-control                Disabled
    udld                         Disabled
    vmps                         Disabled
    psp                          Disabled
    Timer interval: 180 seconds
    Interfaces that will be enabled at the next timeout:
    sh ip arp inspection int output
     Gi2/0/37         Untrusted               15                 1
     Interface        Trust State     Rate (pps)    Burst Interval
     Gi2/0/38         Untrusted               15                 1
     Gi2/0/39         Untrusted               15                 1
     Gi2/0/40         Untrusted               15                 1
     Gi2/0/41         Untrusted               15                 1
     Gi2/0/42         Untrusted               15                 1
     Gi2/0/43         Untrusted               15                 1
     Gi2/0/44         Untrusted               15                 1
     Gi2/0/45         Untrusted               15                 1
     Gi2/0/46         Untrusted               15                 1
     Gi2/0/47         Untrusted               15                 1
     Gi2/0/48         Trusted               None               N/A
     Gi2/0/49         Untrusted               15                 1
    sh cdp  neighbors Gig 2/0/40 det
    Device ID: SEP0004f2440d98
    Entry address(es):
      IP address: 10.210.86.86
    Platform: Polycom SoundPoint IP 450,  Capabilities: Host Phone
    Interface: GigabitEthernet2/0/40,  Port ID (outgoing port): Port 1
    Holdtime : 120 sec
    Version :
    Updater: 5.0.2, App: 4.0.2
    advertisement version: 2
    Duplex: full
    Power drawn: 5.400 Watts
    Power Available TLV:
        Power request id: 0, Power management id: 0, Power available: 0, Power management level: 0
    Management address(es):
    29NEWM434-03#sh run | i arp inspe
    ip arp inspection vlan 11-13,21-23
    Please see the output and config. Please advise.
    Thanks!!

  • Jumbo Frame - Enabling on a VLAN of CAT 6500 running IOS

    Jumbo frames needs to be enabled on one of the vlan interface on Cisco 6500 IOS Switch.
    =================================================================
    •1) Once enabled the mtu 9216 on the required vlan interface do we need to reload the switch to take effect (I believe that in some low end swicthes it needs a reload)
    •2) If we enable only one Vlan interface, how about the other vlan interfaces(about 200 are on this switch)? Do we need to specify mtu1500 on other vlan interfaces?
    I have read information at the following two links, but I still wish to reconfirm by asking the questions in this forum. Someone who has already implemented this may have gained more experience while implementing it on CAT 6500 IOS Switch.
    https://supportforums.cisco.com/message/963341#963341
    http://www.cisco.com/en/US/products/hw/switches/ps700/products_configuration_example09186a008010edab.shtml
    http://www.cisco.com/en/US/products/hw/switches/ps700/products_configuration_example09186a008010edab.shtml#backinfo1
    Thanks.
    Alphonse

    You do not need to reboot your 6500 after you enable jumbo frames, but it is good idea to do it during an outage window. You only need to reboot smaller switches i.e. 3560, 3750, etc...after enabling jumbo frames. On these switches you can only enable it globally.  Only enable jumbo frames for the vlans you need.  You usually need jumbo frames for vlans connecting to the storage systems.
    Good Luck

Maybe you are looking for