Keyboard not found after system update

I completed a system update on the iMac, which required a restart.  Now the iMac cannot find my keyboard.  It is a usb connection working fine before the update.  It is an Apple extended keyboard.  The system is optimizing and looking for a bluetooth keyboard.  I unplugged the keyboard and plugged back in.  I ran disk utility twice.  I restarted the machine.  It is still not recognized.  The Bluetooth Assistant has a spinning icon that has run for 30 minutes.  My keyboard does not respond to my typing.  The keyboard is a 2 months old.
What happened? How can I get it working again?
Thank you.
Kelly

Hi Kelly, might try this...
reset FW bus, same goes for USB reset...
Reset the Firewire bus
If your Firewire or USB isn't recognizing any device.  A solution which has worked for some whose hard drive became invisible in 10.4 was simply to follow these four steps to reset the Firewire/USB bus:
1. Shut the machine down.
2. UNPLUG the power lead to the computer and any firewire/USB drive or devices.
3. leave it for 10 minutes.
4. Connect back up and reboot.
http://www.macmaps.com/firewirebug2.html

Similar Messages

  • Device not found after system update

    After running a system upate from 10.4.0 to 10.4.11, Final Cut Pro no longer finds my camera at startup. Refreshing device in FCP does nothing. I tried installing the Pro updates, deleting preferences, and repairing permissions. The camera is found in iMovie and System Profiler, so it's not a hardware issue. If I need to downgrade the OS, to what version, and how do I update from 10.4.0 to something other than 10.4.11?

    Ya know? They have such a bad rap generally with their interface with FCP that I shy away from using them... Sony cameras seem to always work, as do Panasonic units... can't say I know more than that, but Apple has tested many cameras and there is a list of what device control setting to use here: http://www.apple.com/finalcutstudio/resources/devicelist.php#results If you search with all, canon, all... you'll see the basic setting is pretty much every camera in every version of FCP with few exceptions.
    I think the bad rap comes from the timecode signals recorded with them.. they seem to be weak enough that many times FCP reports a break in timecode where there really isn't one... Can't say why, but if you just search this forum on "Canon" you'll find a lot of problems with the interface with FCP. Been that way for years too.
    If you're really going to go through a revert, I'd suggest you go all the way and reformat the startup disk and install it all again.. might use another drive for this and keep your current setup. That's what I've been doing for quite some time now, and it lets me "ease" into new OS's and versions of software that way. Also allows me to setup beta startup disks for beta testing that I do for a bunch of folk.
    Jerry

  • BannerMaker not working after system update.

    Hello all,
    I am not trusting Apple now for system updates anymore, because the last couple of updates, after updating my system software, I have problems. I never have these issues with Windows.
    Getting to my point, I use BannerMaker (an app created by some Fed agency that I had found googling because Apple doesn't support it as standard, and Windows already had this for years to comply with DOD requirements) to use for a login warning legal note, etc. This goes on to the login window only when you disable the icon/name login. I was in the process of updating it and it told me that the loginwindow.plist wasn't found. I found it on the Spotlight, but I had no way of changing it.
    I should also note that after the system update, the login process reverted back to the icon/name login, which never happened. I always require me and another user to type their username because to protect the user's privacy.
    How can I get BannerMaker to work again, or how can I get into that file so I can change it and I also want to know if other users had their loginwindow settings mysteriously affected by the update?
    I am really disappointed by the lousy updates that paralyzes my security and other issues with previous updates, which I won't get into. I am disappointed with Apple right now.
    Steven

    I had a feeling that was going to happen. Well I just don't have the patience to do that. Apple needs to go onto the Windows system that you could delete specific updates rather than reinstalling the system software. And I also don't like how updates affect work around apps, how they close them down because they are not authorized software. I need a secure system, and Apple won't let me. **** to screw with them, I might just give my mother my MacBook and I go get a Windows notebook. I had nothing but problems since I got this MacBook.

  • My iPad will not sync after system update and returns message that my computer is no longer authorised.

    Please help me sync my iPad as it is not able to sync after a system update.  Several messages 1. Computer no longer authorised and when I reauthorise it it prepares to sync and then it tells me my iPad cannot be written to,

    Hi leefromwoodford,
    The following article will tell you how to transfer purchased music from your iPhone to the your Mac -
    iTunes: How to move your music to a new computer
    http://support.apple.com/kb/HT4527
    Specifically -
    Transferring purchases
    If your iPhone, iPad, or iPod has your purchased content from the iTunes Store, you can transfer the content to a computer that is authorized for your Apple ID.
    Note: This option only works for content you purchased from the iTunes Store (as opposed to content from other sources, such as CDs you may have imported). For content you did not purchase from the iTunes Store, synchronization occurs in one direction only. This means your content can be copied from a computer to your iOS device, but cannot be copied from your device to a computer.
    Open iTunes.
    From the Store menu, choose Authorize This Computer.
    Enter your Apple ID and password. Then, click the Authorize button.
    Connect your device your computer. If it is synced with another iTunes library, you may be asked if you want to "Erase and Sync" or "Transfer Purchases."
    If that alert appears, click Transfer Purchases.
    Important: Clicking Erase and Sync will delete any existing content currently on your device. The content would then be replaced with the content that is on the computer.
    If you were not offered the option to transfer purchases:
    After connecting your device to the computer, its icon appears in iTunes. Click the icon.
    From the File > Devices menu, choose "Transfer Purchases from 'Your device name.'"
    Note that the computer must be authorized for the Apple ID under which the purchases were made.
    You may also want to download the music directly from the iTunes store, rather than using the iPhone. See this article -
    Download past purchases
    http://support.apple.com/kb/HT2519
    Thanks for using Apple Support Communities.
    Best,
    Brett L

  • [SOLVED] Audio not working after system update

    Hi all,
    About 4 days ago, I installed Arch Linux (full systemd) with LXDE on a Dell Inspiron Mini netbook. Everything seemed to be OK until today, when I did pacman -Syu and then installed the SLiM login manager. After rebooting there was no audio. I am not sure if this happened because of the upgrade or because of SLiM. I am pretty new to systemd, so I could be missing something very obvious. I have tried many things so far, with no success:
    1) I disabled SLiM and instead started X from the terminal at boot, and nothing happened.
    2) I have removed my username from the 'audio' group, added it again, removed it, etc... No change.
    3) I downgraded systemd, systemd-sysvcompat, and xine-lib (just in case) to their previous version and nothing happened.
    4) I seem to be detecting the sound card correctly. If I run "aplay -l" as my normal, non-root user I get the same output as the root user:
    **** List of PLAYBACK Hardware Devices ****
    card 0: Intel [HDA Intel], device 0: ALC272 Analog [ALC272 Analog]
    Subdevices: 1/1
    Subdevice #0: subdevice #0
    5) If I login with SLiM, my session seems to be setup correctly, as far as I can tell:
    $ loginctl show-session $XDG_SESSION_ID
    Id=1
    Timestamp=Mon, 2012-10-29 00:38:35 EDT
    TimestampMonotonic=14973592
    DefaultControlGroup=name=systemd:/user/vrg/1
    VTNr=7
    Display=:0.0
    Remote=no
    RemoteUser=root
    Service=slim
    Leader=274
    Audit=1
    Type=x11
    Class=user
    Active=yes
    State=active
    KillProcesses=no
    IdleHint=no
    IdleSinceHint=0
    IdleSinceHintMonotonic=0
    Name=vrg
    6) I reinstalled pulseaudio, pulseaudio-alsa, alsa-plugins, and alsa-oss... Nothing.
    7) I do not have the ~/.asoundrc file.
    Here is a full list of the packages I upgraded:
    [2012-10-28 11:19] Running 'pacman -Syy'
    [2012-10-28 11:19] synchronizing package lists
    [2012-10-28 11:19] Running 'pacman -Syu'
    [2012-10-28 11:19] synchronizing package lists
    [2012-10-28 11:19] starting full system upgrade
    [2012-10-28 11:20] upgraded linux-api-headers (3.5.5-1 -> 3.6.3-1)
    [2012-10-28 11:20] Generating locales...
    [2012-10-28 11:20] en_US.UTF-8... done
    [2012-10-28 11:20] Generation complete.
    [2012-10-28 11:21] upgraded glibc (2.16.0-4 -> 2.16.0-5)
    [2012-10-28 11:21] upgraded binutils (2.22-10 -> 2.23-1)
    [2012-10-28 11:21] upgraded bison (2.6.2-1 -> 2.6.4-1)
    [2012-10-28 11:21] upgraded coreutils (8.19-1 -> 8.20-1)
    [2012-10-28 11:21] upgraded systemd (194-4 -> 195-2)
    [2012-10-28 11:21] upgraded device-mapper (2.02.97-1 -> 2.02.98-1)
    [2012-10-28 11:21] upgraded cryptsetup (1.5.0-2 -> 1.5.1-1)
    [2012-10-28 11:21] installed nss-myhostname (0.3-3)
    [2012-10-28 11:21] warning: /etc/shadow installed as /etc/shadow.pacnew
    [2012-10-28 11:21] upgraded filesystem (2012.10-1 -> 2012.10-2)
    [2012-10-28 11:21] upgraded firefox (16.0.1-1 -> 16.0.2-1)
    [2012-10-28 11:21] upgraded gcc-libs (4.7.2-1 -> 4.7.2-2)
    [2012-10-28 11:21] upgraded gcc (4.7.2-1 -> 4.7.2-2)
    [2012-10-28 11:21] upgraded lirc-utils (1:0.9.0-32 -> 1:0.9.0-33)
    [2012-10-28 11:21] upgraded lvm2 (2.02.97-1 -> 2.02.98-1)
    [2012-10-28 11:21] upgraded mkinitcpio (0.10-1 -> 0.11.0-1)
    [2012-10-28 11:21] upgraded syslinux (4.05-7 -> 4.06-1)
    [2012-10-28 11:21] upgraded systemd-sysvcompat (194-4 -> 195-2)
    [2012-10-28 11:21] upgraded xine-lib (1.2.2-2 -> 1.2.2-3)
    More information:
    $ ls -l /dev/snd
    total 0
    drwxr-xr-x 2 root root 60 Oct 29 00:38 by-path
    crw-rw----+ 1 root root 116, 5 Oct 29 00:38 controlC0
    crw-rw----+ 1 root root 116, 4 Oct 29 00:38 hwC0D0
    crw-rw----+ 1 root root 116, 3 Oct 29 00:38 pcmC0D0c
    crw-rw----+ 1 root root 116, 2 Oct 29 01:53 pcmC0D0p
    crw------- 1 root root 116, 1 Oct 29 00:38 seq
    crw-rw----+ 1 root root 116, 33 Oct 29 00:38 timer
    $ lsmod | grep '^snd' | column -t
    snd_hda_codec_realtek 52245 1
    snd_hda_intel 22256 1
    snd_hda_codec 83677 2 snd_hda_codec_realtek,snd_hda_intel
    snd_hwdep 4746 1 snd_hda_codec
    snd_pcm 61470 2 snd_hda_codec,snd_hda_intel
    snd_page_alloc 5869 2 snd_pcm,snd_hda_intel
    snd_timer 14902 1 snd_pcm
    snd 44874 8 snd_hda_codec_realtek,snd_hwdep,snd_timer,snd_pcm,snd_hda_codec,snd_hda_intel
    If I run 'fuser -v /dev/snd/*' I get nothing (blank) and if I run 'fuser -v /dev/dsp' I get file not found. I've also done 'amixer sset Master unmute' and 'speaker-test'. Everything seems OK, except that I can't hear anything!
    Any help or suggestions that could point me in the right direction would be greatly appreciated.
    Last edited by vrg (2012-10-29 07:25:36)

    Thanks Rasi. Incidentally, I just solved the issue a few minutes ago and was about to post the answer, but yes, you are right... the device was muted. It's embarrassing, but it did not seem obvious to me that the device was muted... All the sliders seemed OK, with nice, green values between 50 and 100. Also, the LXDE volume control was unmuted with a value between 50% and 100%, and I ran the 'amixer sset Master unmute' command several times. Clearly, this command does not do the job.
    What I was missing is nicely described in the PulseAudio troubleshooting:
    If one experiences no audio output via any means while using ALSA, attempt to unmute the sound card. To do this, launch alsamixer and make sure each column has a green 00 under it (this can be toggled by pressing 'm')
    I was not pressing 'm'... I know it's on the wiki, but this did not seem to be a PulseAudio issue, which was working perfectly yesterday and was not upgraded, so the PulseAudio troubleshooting was not the first place I looked for solutions. I wonder why the device got muted in the first place.
    Thanks again for the help!

  • Excite PRO 3G connection not work after system update

    Hello, I live in Italy and on last Sunday (january 26th) my Excite PRO tablet (model AT10LE-A-10H) got the Android version 4.3.201121220.35. After restart my wifi works fine, all other app work fine, but my 3g connection doesn't work, mobile network bar is empty and it says "no service". My sim card is ok. I used this sim card before the system update and I didn't get any problem with Android 4.2.2.
    Please help me   I'm waiting for your help.
    Thank you
    Regards

    This is the forums for Toshiba USA. Unfortunately, we don't have informaiton about your model. You may want to contact Toshiba in your region. You could check the Toshiba Europe forums.
    - Peter

  • Touch screen not working after system update

    A few months ago, my laptop (Satelitte P55t-A5202) went through an automatic system update.  Ever since then, my touch screen won't work.  I followed the directions to reinstall the HDI programs several times.  The first time it worked but only for a few hours. The next time I tried to reinstall, it worked for a second.  Now reinstalls do nothing. 
    Before the system update, my touchscreen worked fine.  And in reading the forums, this seems to be a common problem with the updates.  I called TOSHIBA customer service for help.  The FIRST thing they want to do is charge me for tech support because my laptop is out of warranty.  I told the customer service rep repeatedly that my touch screen worked fine until the update.  He refused to give me any help because I did not want to pay for him to tell me how to resolve...
    In my opinion, this is a toshiba issue not mine so regardless if my laptop is out of warranty, Toshiba should take ownership and be accountable for the problems they cause.
    Does anyone have any suggestions as to how to take care of this?
    By the way, Toshiba customer service representative was rude, you could barely understand him because of his accent, I had to repeat SEVERAL times what my issue was because he couldn't get past the warranty issue and I had to ask several times to speak with a supervisor ( to which he told me a supervisor would call me instead)

    See my reply in the laptop forum.
    -Jerry

  • Silverlight and google chrome not working after system update

    I just did a system update and now google chrome and the silverlight plugin do not work. I've tried uninstalling and reinstalling both numerous times, restarted, and checked for updates again but nothing works. What's going on? 

    Check compatibility with their respective vendors.

  • Nautilus will not Start after system update

    I just updated my system with "pacman -Syu" and it now will not open the nautilus file manager. Looking inside the journal it shows the following error:
    gnome-session[647]: Window manager warning: Log level 16: AT-SPI: Error in GetItems, sender=(null), error=Did not receive a reply. Possible causes include: the remote application did not send a reply, the message bus security policy blocked the reply, the reply timeout expired, or the network connection was broken.
    Here is a list of files that was just upgraded:
    [2014-08-31 15:27] [PACMAN] Running 'pacman -Syu flashplugin'
    [2014-08-31 15:27] [PACMAN] synchronizing package lists
    [2014-08-31 15:27] [PACMAN] starting full system upgrade
    [2014-08-31 15:28] [ALPM-SCRIPTLET]  >>
    [2014-08-31 15:28] [ALPM-SCRIPTLET]  >> If you have an NVIDIA card that supports libvdpau or Broadcom Crystal HD chips,
    [2014-08-31 15:28] [ALPM-SCRIPTLET]  >> uncomment EnableLinuxHWVideoDecode=1 from /etc/adobe/mms.cfg.
    [2014-08-31 15:28] [ALPM-SCRIPTLET]  >> If you run into problems, please contact nVidia or Broadcom along with your system config info / driver version.
    [2014-08-31 15:28] [ALPM-SCRIPTLET]  >>
    [2014-08-31 15:28] [PACMAN] installed flashplugin (11.2.202.400-1)
    [2014-08-31 15:28] [PACMAN] upgraded avahi (0.6.31-12 -> 0.6.31-13)
    [2014-08-31 15:28] [PACMAN] upgraded bash (4.3.022-1 -> 4.3.024-1)
    [2014-08-31 15:28] [PACMAN] upgraded bluez (5.22-1 -> 5.22-2)
    [2014-08-31 15:28] [PACMAN] upgraded poppler (0.26.3-1 -> 0.26.4-1)
    [2014-08-31 15:28] [PACMAN] upgraded cups-filters (1.0.57-1 -> 1.0.58-1)
    [2014-08-31 15:28] [PACMAN] upgraded libgcrypt (1.6.1-1 -> 1.6.2-1)
    [2014-08-31 15:28] [PACMAN] upgraded libsystemd (215-4 -> 216-1)
    [2014-08-31 15:28] [PACMAN] upgraded systemd (215-4 -> 216-1)
    [2014-08-31 15:28] [PACMAN] upgraded device-mapper (2.02.109-1 -> 2.02.109-2)
    [2014-08-31 15:28] [PACMAN] upgraded libtasn1 (4.0-1 -> 4.1-1)
    [2014-08-31 15:28] [PACMAN] upgraded gnutls (3.3.6-1 -> 3.3.7-1)
    [2014-08-31 15:28] [PACMAN] upgraded gstreamer (1.4.0-1 -> 1.4.1-1)
    [2014-08-31 15:28] [PACMAN] upgraded gst-plugins-base-libs (1.4.0-1 -> 1.4.1-1)
    [2014-08-31 15:28] [PACMAN] upgraded gst-libav (1.4.0-2 -> 1.4.1-1)
    [2014-08-31 15:28] [PACMAN] upgraded gst-plugins-bad (1.4.0-1 -> 1.4.1-1)
    [2014-08-31 15:28] [PACMAN] upgraded gst-plugins-base (1.4.0-1 -> 1.4.1-1)
    [2014-08-31 15:28] [PACMAN] installed zita-alsa-pcmi (0.2.0-1)
    [2014-08-31 15:28] [PACMAN] installed zita-resampler (1.3.0-2)
    [2014-08-31 15:28] [PACMAN] upgraded jack (0.124.1-1 -> 0.124.1-3)
    [2014-08-31 15:28] [PACMAN] upgraded gst-plugins-good (1.4.0-1 -> 1.4.1-1)
    [2014-08-31 15:28] [PACMAN] upgraded gtksourceview3 (3.12.2-1 -> 3.12.3-1)
    [2014-08-31 15:28] [PACMAN] upgraded imagemagick (6.8.9.6-1 -> 6.8.9.7-1)
    [2014-08-31 15:28] [PACMAN] upgraded libnl (3.2.24-1 -> 3.2.25-1)
    [2014-08-31 15:28] [PACMAN] upgraded libpcap (1.5.3-1 -> 1.6.1-1)
    [2014-08-31 15:28] [PACMAN] upgraded libtracker-sparql (1.0.2-1 -> 1.0.3-1)
    [2014-08-31 15:28] [PACMAN] upgraded libwacom (0.9-1 -> 0.10-1)
    [2014-08-31 15:28] [PACMAN] upgraded libxkbcommon (0.4.2-1 -> 0.4.3-1)
    [2014-08-31 15:28] [PACMAN] installed thin-provisioning-tools (0.3.2-1)
    [2014-08-31 15:28] [PACMAN] upgraded lvm2 (2.02.109-1 -> 2.02.109-2)
    [2014-08-31 15:28] [PACMAN] upgraded man-pages (3.70-1 -> 3.71-1)
    [2014-08-31 15:28] [PACMAN] upgraded ntp (4.2.7.p446-2 -> 4.2.7.p465-1)
    [2014-08-31 15:28] [ALPM] warning: /etc/pacman.d/mirrorlist installed as /etc/pacman.d/mirrorlist.pacnew
    [2014-08-31 15:28] [PACMAN] upgraded pacman-mirrorlist (20140706-1 -> 20140823-1)
    [2014-08-31 15:28] [PACMAN] upgraded poppler-glib (0.26.3-1 -> 0.26.4-1)
    [2014-08-31 15:28] [PACMAN] upgraded spice-gtk3 (0.24-3 -> 0.24-4)
    [2014-08-31 15:28] [PACMAN] upgraded systemd-sysvcompat (215-4 -> 216-1)
    [2014-08-31 15:28] [PACMAN] upgraded tcl (8.6.1-1 -> 8.6.2-1)
    [2014-08-31 15:28] [PACMAN] upgraded telepathy-farstream (0.6.1-1 -> 0.6.2-1)
    [2014-08-31 15:28] [PACMAN] upgraded tracker (1.0.2-1 -> 1.0.3-1)
    [2014-08-31 15:28] [PACMAN] upgraded tzdata (2014e-1 -> 2014f-1)
    [2014-08-31 15:28] [PACMAN] upgraded webkitgtk (2.4.4-1 -> 2.4.5-1)
    [2014-08-31 15:28] [PACMAN] upgraded webkitgtk2 (2.4.4-1 -> 2.4.5-1)
    would any of these packages cause this? Thanks.
    Last edited by djmwj1 (2014-08-31 23:15:33)

    Please edit your post to use BBCode Code tags around program output.  That reference link is also below every post box on the forums.   Thanks.

  • Desktop setting not saving after system update

    Hi All,
    I did a system wide update including the changing the kernel from 2.6.25 to 2.6.28 and now I cannot change my desktop setting.
    that is, my desktop background picture and font size is not saving. First I could not shutdown and i read the forum where
    it was suggested to downgrade from hal-0.5.11-7 to hal-0.5.11-4. and that work for me. but my system
    not saving my desktop setting. I have the "automatically save session on logout" check.
    I am using xfce4 as my DM
    any help please.

    hi,
    check your home folder permissions. open up your /home/ right click on your username folder click properties and in permissions dialog check that owner can view/edit files and then check something like apply to all subfolders and files

  • Broadcom driver not working after system update on 10/10/2014

    Yesterday I updated my system (pacman -Syyu) and after rebooting my wireless card is no longer detected by the operating system. I have a 15 inch macbook pro (late 2013) with a broadcom BCM4360 wireless card. It was tough to get working in the first place, but eventually I got it to work with the broadcom-wl-dkms driver. The package is still installed, so I have no idea what to do because I have tried all of the available broadcom driver packages that I know to exist.

    Did you rebuild the wireless driver after updating the system? I've never quite figured out how to deal with the dkms variation of the drivers so you are on your own for the correct syntax (surely in the wiki somewhere), but I know that for my BCM4314 with the broadcom-wl driver, every time there is an update to the kernel, I need to rebuild the broadcom-wl driver (even if broadcom-wl itself didn't change) so that the wl.ko module shows up in the appropriate place in the kernel modules directory.

  • Qiv not work after system update

    error message:
    zhiwen ~/ qiv /doc/img/1.jpg
    Gdk-ERROR **: BadMatch (invalid parameter attributes)
      serial 115 error_code 8 request_code 2 minor_code 0
    Locking assertion failure.  Backtrace:
    #0 /usr/lib/libxcb-xlib.so.0 [0xb7b02767]
    #1 /usr/lib/libxcb-xlib.so.0(xcb_xlib_lock+0x2e) [0xb7b0281e]
    #2 /usr/lib/libX11.so.6 [0xb7c9de08]
    #3 /usr/lib/libX11.so.6(XSync+0x25) [0xb7c92ce5]
    #4 /usr/lib/libgdk-1.2.so.0(gdk_flush+0x28) [0xb7da0fb8]
    #5 /usr/lib/libgdk-1.2.so.0(gdk_image_destroy+0x65) [0xb7da84c5]
    #6 /usr/lib/libgdk-1.2.so.0(gdk_image_exit+0x2a) [0xb7da85da]
    #7 /usr/lib/libgdk-1.2.so.0 [0xb7d942a5]
    #8 /lib/libc.so.6(exit+0xd5) [0xb7b344cd]
    #9 /usr/lib/libgdk-1.2.so.0 [0xb7d94386]
    #10 /usr/lib/libX11.so.6(_XError+0xd3) [0xb7c97053]
    #11 /usr/lib/libX11.so.6 [0xb7c9e72c]
    #12 /usr/lib/libX11.so.6(_XReply+0x15a) [0xb7c9eaea]
    #13 /usr/lib/libX11.so.6(XSync+0x6a) [0xb7c92d2a]
    #14 /usr/lib/libgdk-1.2.so.0(gdk_flush+0x28) [0xb7da0fb8]
    #15 qiv(update_image+0x384) [0x804c744]
    qiv: xcb_xlib.c:73: xcb_xlib_lock: Assertion `!c->xlib.lock' failed.
    Aborted
    please help.

    Hello,
    I have the same error since about two weeks. Today I tried to solve that problem and i found this link:
    https://bugs.launchpad.net/ubuntu/+sour … +bug/41056
    So to fix the problem you have to do:
    export XLIB_SKIP_ARGB_VISUALS=1
    It seems to be a problem with imlib1 and the X composite extension..... I don't really know what that means .
    For those people all were fine with the versions:
    ii gdk-imlib11 1.9.14-32ubuntu1 imaging library for use with gtk
    ii qiv 2.0-7 A quick image viewer for X
    and personally I have
    local/imlib 1.9.15-3
    General image handling library for X11 and Gtk
    local/imlib2 1.4.0-1
    Imlib2 is the successor to Imlib. It is NOT a newer version -- Imlib 2 can
    be installed alongside Imlib 1.x
    local/qiv 2.0-1
    Quick Image Viewer (qiv) is a very small and fast GDK/Imlib image viewer
    Perhaps the qiv version is too old. Could anyone help ?

  • T40 KEYBOARD NOT WORKING AFTER STARTUP

    IBM THINKPAD LAPTOP
    T40  237372M
    OS WINDOWS XP PRO SP3
    •86 key keyboard with imbedded numeric keypad and
    integrated UltraNav dual-pointing system, featuring TrackPoint and customized touch pad
    SUBJECT; KEYBOARD NOT WORKING
    AFTER STARTUP UNABLE TO OPEN SOFTWARE OR USE TEXT IN NOTEPAD AND OPENOFFICE
    I HAVE A TEMPORARY  SOLUTION TO OVERCOME THIS PROBLEM BY;
    1 )USING MOUSE OPEN START/ THEN  NOTEPAD
    STILL UNABLE TO ENTER TEXT
    2) OPEN START/ONSCREEN KEYBOARD CLICK ON LOCK THEN EXIT
    3)GO BACK TO NOTEPAD ENTER TEXT, NOW WORKING I THEN EXIT
    WITHOUT SAVING
    I TRIED REINSTALLING XP AND LOST MS WORD THAT IS WHY I AM USING OPEN OFFICE
    I THOUGHT IT MAY HAVE BEEN THE SP3 UPDATE BUT AFTER USING IBM SYS REINSTALL
    DURING RE INSTALL I WAS UNABLE TO USE TEXT FOR WINDOWS LOGIN
    THE ONLY KEYS TO USE WERE ÁÉÍÓÚ BEING LATIN CHARACTERS WITH ACUTE SIGN
    CAN ANYONE CAN HELP ME THANKS

    Hi and welcome to the forum!
    Does the keyboard work fine inside the BIOS?
    Also try booting from LiveCD of Ubuntu, if issue remains then the keyboard is faulty.
    Keep us informed.
    Maliha (I don't work for lenovo)
    ThinkPads:- T400[Win 7], T60[Win 7], IBM 240[Win XP]
    IdeaPad: U350
    Apple:- Macbook Air [Snow Leopard]
    Did someone help you today? Compliment them with a Kudos!
    Was your question answered today? Mark it as an Accepted Solution! 
      Lenovo Deutsche Community     Lenovo Comunidad en Español 
    Visit my YouTube Channel

  • Lack of 3g after system update

    Hello :-)
    It's problem with Xperia E dual
    Few days ago I updated the system to the 4.1.1 version (compilation 11.3.A.1.39).
    Unfortunatelly after updating I've discovered that smartphone don't works with 3G. On the display I've only icon "E". Before updating there was typically "H". Of course now the transfer is slower than before and of course I'm not happy of that.
    I try to solve this problem - choose in menu list of available provider and... there are only 2G nets. Because I've functioning still in the same place of live and the problem has occured after the updating I'm sure that it's strictly connected.
    Is there any solution for that?
    Another problem is with trying to call. After system updating typically twice a day I have to restart smartphone because it's totally hanged. No one can connect with me and I can't call to anybody. Smartphone looks normally and doesn't give any siglan that something is wrong. But when I try to connect to somebody I direst the number and... there is no signal at all. After few seconds telephon return to main menu. There is also no record about this trial of connection in the list of done connections. It's very uncomfortable situation.
    Sure, there are also some adventages with the system updating but problems mentioned above are really annoing.
    Have you any solutions for it?
    Thanks in advance.
    Rafal
    Solved!
    Go to Solution.

    Hi, try repairing phone software with PC Companion or Update Service.
    http://www.sonymobile.com/gb/tools/pc-companion/
    http://www.sonymobile.com/gb/tools/update-service/
    Be aware that this will erase phone data completely, backup if necessary.
    Before proceeding with software repair, confirm with your Network Operator that there is nothing wrong with the network. Also, remove and reinsert SIM card and try again (have a close look at the contact surface, ensure that it is relatively clean).
    Don't forget to mark correct answer as Accepted Solution.
    If you find the post helpful, press Kudos.

  • HT2693 My UPAD lite does not start after recent update. I have lots of info in it. Can anybody help me to get it back. Can I get the update out somehow? Thanks

    My UPAD lite does not start after recent update. I have lots of info in it. Can anybody help me to get it back? Can I somehow undo the update? Thanks

    "UPAD lite?"
    I expect that you mean some version of iPad.
    First, try a system reset.  It cures many ills and it's quick, easy and harmless...
    Hold down the on/off switch and the Home button simultaneously until the screen blacks out or you see the Apple logo.  Ignore the "Slide to power off" text if it appears.  You will not lose any apps, data, music, movies, settings, etc.
    If the Reset doesn't work, try a Restore.  Note that it's nowhere near as quick as a Reset.  Connect via cable to the computer that you use for sync.  From iTunes, select the iPad/iPod and then select the Summary tab.  Follow directions for Restore and be sure to say "yes" to the backup.  You will be warned that all data (apps, music, movies, etc.) will be erased but, as the Restore finishes, you will be asked if you wish the contents of the backup to be copied to the iPad/iPod.  Again, say "yes."
    At the end of the basic Restore, you will be asked if you wish to sync the iPad/iPod.  As before, say "yes."  Note that that sync selection will disappear and the Restore will end if you do not respond within a reasonable time.  If that happens, only the apps that are part of the IOS will appear on your device.  Corrective action is simple -  choose manual "Sync" from the bottom right of iTunes.
    If you're unable to do the Restore, go into Recovery Mode per the instructions here.

Maybe you are looking for