Laptop battery drains after shut down

Hi, I have bought hp pavilion 15-no28se  six months back,
Its working good, but one issue is contantly irritating me, it is due to its battery drainage after shut down overnight.It almost drains 8-10 percent withing 12 hours. Whereas, I properly shut down it and caliberated as well, but of no use. Although, battery status is OK, and I think battery is fine becasue once I took out battery from laptop for 24 hours, then inserted again and checked it and not a single percent dropped down.
I am so tense that why it is draining when battery works well and properly shut down?Please guide me on this.I am waiting..

Hello again rocket_sc,
I hope you had a great weekend!
To test, calibrate, and re-synchronize your battery you will need to first follow the steps in this document on Testing and Calibrating the Battery (Windows 8). Once this is completed, and the battery continues to drain, then you can move to re-install the ACPI-Compliant Control Method Battery.
I understand that this process can be a little overwhelming, but not to worry! I would gladly expand on the steps provided above!
To answer your first question: you are not uninstalling the software as you would from Programs and Features (like uninstalling software downloaded from a CD). Instead, you are removing small driver components removable from the Device Manager. 
To get the Device Manager, please follow the steps below:
Step 1. Go to Device Manager:
a. Press the  and type "Device Manager"
b. Click the Device Manager tab on the top right-hand side.
c. The Device Manager should be open.
Step 2. Select Batteries:
a. Click the right-facing triangle to the left hand side of "batteries"
Step 3. Right click the "Microsoft ACPI-Compliant Control Method Battery" that is listed there
a. If you see any duplicates of the "Microsoft ACPI-Compliant Control Method Battery", please select them both.  
Step 4. Click Uninstall
a. You might also see an option that says "disable." Please disregard this option, and click on Uninstall. 
Step 5. At the prompt put a check in the box to remove the current driver
Step 6. Restart the computer
Step 7: Remove the battery for one minute and then put it back in
When the computer comes back up it should automatically find and install the driver.
Step 8. Go to Device Manager
a. Press the  and type "Device Manager"
b. Click the Device Manager tab on the top right-hand side.
c. The Device Manager should be open.
Step 9. Select Batteries
a. Click the right-facing triangle to the left hand side of "batteries"
Step 10. Right click the "Microsoft ACPI-Compliant Control Method Battery" that is listed there (there should only be one).
Step 11. Click "Update Driver Software"
Do the same thing with Microsoft ACPI-Compliant Embedded Controller.
a. If you do not see this parcel of software in the Device Manager, please skip this step. If you do, the same steps would include:
* Right-clicking this device driver in the Device Manager
* Click on "uninstall"
* Put a check in the box next to "remove the current driver" and pressing "ok"
* Restarting the computer
* Remove the battery for one minute, then re-insert it
* Return to the Device Manager
* Right-clicking the Microsoft ACPI-Compliant Embedded Controller
* Click "update driver software"
Please re-post with the results of your troubleshooting, and I look forward to your reply!
Regards
MechPilot
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the right to say “Thanks” for helping!

Similar Messages

  • Turn off cellular for apps and they turn back on. Fast battery drain. Shuts down at 30-40%. Battery reads "0" when but rises quickly to 17

    Turn off cellular for apps and they turn back on. Fast battery drain. Shuts down at 30-40%. Battery reads "0" when but rises quickly to 17 & charges.  Happened after IOS upgrades. Have 3 iPhone 4S for 1-2 years & 1 iPhone 5, w/same problem.

    Back up and restore using iTunes.

  • HP ENVY dv6t-7300 QUAD: Battery Drains when Shut Down & Doesn't Charge when Battery life is 93%

    My HP ENVY dv6t-7300 QUAD had battery discharge when I left it off for a few days on, so far, three occasions:
    The battery fully discharged to 0% from 100% when the laptop was left off for a peroid of two weeks
    The battery discharged to 95% from 100% when left off for a seperate period of three days
    The battery discharged to 94% from 100% when left off for a seperate peroid of four days
    These three instances did NOT come consecutively.  
    When the laptop is left off for one day though, the battery life is at 98% or 99%.
    On all occasians, the computer was shut down from the settings tab and NOT put into sleep mode or hibernate mode.
    The other issue is that on two different occasions the laptop says that the battery is not charging when the battery life is > 93%.  So far, I have not seen this problem appear when the laptop was below 93% battery.
    This problem is intermittent.  The first time it happened, the laptop began to charge at 93% battery life and continuted to sucessfully charge until today (8/11/2013).  Currently, the battery life is at 97% and the battery will not charge.
    I have performed a start-up battery test and the result displayed on the start-up screen is:
    Battery Check: Primary-OK (1)
    The result from the HP Battery Check from the Desktop Screen says:
    Status: OK (0)
    Charge Capacity: 97%
    This screen also says that the battery is:
    Charged (97%)
    Current: 0mA
    Full Charge Capacity: 5458mAh
    Remaining Capacity: 5319mAh
    Failure ID: OK
    There is also one other interesting thing about this laptop:
    When HP Searches for Drivers for my laptopr, the driver detection program detects that I have an HP ENVY dv6-7398ca, not a dv6t-7300 QUAD like it states under the battery compartment.
    I have had this laptop since abour June 20, 2013 and I believe the warrenty is still good on the parts.
    If anyone has any suggestions on how to fix these problems, I would greatly appreciate it.  Thank you.

    bump? no help?

  • Laptop wont start after shut down.

    Hello, i got problem with HP Pavilion g6.
    Yesterday i watched youtube, and laptop was on side, when i got too tired, then i shut down and left it on side for the night.In the morning i got home and thinked that battery is too low to start but when i plugged in power cable then the light even didnt turn on that's next to plug in hole. I have checked my power cable,it works fine but laptop dont do a single thing, even not the single light wont work.
    Sorry for bad English,and its hard to write with phone.
    Thank you.

    Hello Uku,
    Welcome back to the HP Forums!
    I understand your HP Pavilion G6 notebook does not turn on. If the light around the power connector on the notebook does not light up, either the connector is not functioning or is not getting power from the adapter. If the LED indicator on the adapter is lit, it's a good sign that the adapter is functional, but is not a 100% fool-proof way to determine if it is working.
    If possible, try another power adapter. Any adapter that fits will work for testing purposes. Once you have determined if the adapter works or not, discontinue use immediately and replace the original adapter if an alternate adapter works. You can order parts here: HP Part Surfer. You will need the exact model or product number to use this website. For information on finding your product and model numbers click here: How Do I Find My Model Number or Product Number?
    You may also want to try reconnecting the power connector inside the notebook. For steps on removing and re-seating the power connector you can check out our Maintenance and Service Guide. The steps you're looking for can be found on page 63. Simply remove and reconnect the power connector and see if that resolves the issue. 
    If the above suggestions do not resolve the issue, I recommend you contact phone support for available service options. You can contact HP Technical Support at 1-800-474-6836 in North America. For all other regions click here.
    Hopefully this helps!
    Please click the "Kudos, Thumbs Up" at the bottom of this post if you want to say "Thanks" for helping!
    Please click "Accept as Solution" if you feel my post solved your issue, it will help others find the solution.
    The Great Deku Tree
    I work on behalf of HP.

  • Battery drains while shut down?

    If, having SHUT DOWN (not sleep) my MBA, and let it charge until the magsafe light is green and let it charge overnight, I unhook the magsafe while keeping the MBA off and closed, I leave it TURNED OFF for an entire day, go out to use it elsewhere and when I get there, the battery is completely dead.
    Why? What can I do to fix it?
    The Air seems to shut down MUCH quicker than my old MacBook Pro, so I don't know if it's just not shutting down properly or not. The same thing happens if I hold the power button for a hard shutdown until it shuts off and repeat the charge/wait process.
    Like I said, this is with it SHUT OFF and not in sleep mode. If I can't leave it turned off while I wait in an airport, what's the point exactly? Is anyone else experiencing this? (I know at least one person is on another forum, but no one gave him any answers)

    Used the timer on my iPhone. From green status light (turned off) to when I woke up it was eight hours, 41 minutes, 48.6 seconds later and the battery status was as follows:
    Model Information:
    Serial Number: SMP-ASMB017-3887-8cb
    Manufacturer: SMP
    Device name: ASMB017
    Pack Lot Code: 0000
    PCB Lot Code: 0000
    Firmware Version: 0009
    Hardware Revision: 0401
    Cell Revision: 0100
    Charge Information:
    Charge remaining (mAh): 2938
    Fully charged: No
    Charging: No
    Full charge capacity (mAh): 4977
    Health Information:
    Cycle count: 9
    Condition: Good
    Battery Installed: Yes
    Amperage (mA): -1101
    Voltage (mV): 7522
    System Power Settings:
    AC Power:
    System Sleep Timer (Minutes): 0
    Disk Sleep Timer (Minutes): 10
    Display Sleep Timer (Minutes): 20
    Automatic Restart On Power Loss: No
    Wake On AC Change: No
    Wake On Clamshell Open: Yes
    Display Sleep Uses Dim: Yes
    Battery Power:
    System Sleep Timer (Minutes): 5
    Disk Sleep Timer (Minutes): 10
    Display Sleep Timer (Minutes): 1
    Wake On AC Change: No
    Wake On Clamshell Open: Yes
    Display Sleep Uses Dim: Yes
    Reduce Brightness: Yes
    Hardware Configuration:
    UPS Installed: No
    AC Charger Information:
    Connected: No
    Charging: No
    That's a 41% DRAIN in battery overnight, with it being turned off.
    *Makes appointment at Genius Bar* I'll post results of the visit here just in case anyone else has this problem.

  • Lenovo 510 new laptop battery drains after 70%

    I just bought a new laptop g510 lenovo . Battery works fine for first week .But suddenly it is draining alot and its back remains 1 hour after fully charged.It doesnot even enter to 60% after 70% a message appear " Your batttery is critically low 6%".
    Need help please if there is any way to maintain my battery 

    Hi Ghazanfar,
    As the battery status is “Good” and the issue persists. I would suggest you to contact our Technical Support for further Assistance to get the details of the nearest Authorized Service Center to get the issue analyzed.
    Click here to open a link where you can select the country and get the exact contact support number. I’m sure they will be a great help.
    Do post us back for further queries.
    Best Regards
    Shiva Kumar
    Did someone help you today? Press the star on the left to thank them with a Kudo!
    If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
    Follow @LenovoForums on Twitter!

  • Battery drains unless shut down on top right. Just touched, not powered down

    I suspect this has to do with some App that is too power hungry.  My prime suspect is NEST.  Any thoughts?

    Used the timer on my iPhone. From green status light (turned off) to when I woke up it was eight hours, 41 minutes, 48.6 seconds later and the battery status was as follows:
    Model Information:
    Serial Number: SMP-ASMB017-3887-8cb
    Manufacturer: SMP
    Device name: ASMB017
    Pack Lot Code: 0000
    PCB Lot Code: 0000
    Firmware Version: 0009
    Hardware Revision: 0401
    Cell Revision: 0100
    Charge Information:
    Charge remaining (mAh): 2938
    Fully charged: No
    Charging: No
    Full charge capacity (mAh): 4977
    Health Information:
    Cycle count: 9
    Condition: Good
    Battery Installed: Yes
    Amperage (mA): -1101
    Voltage (mV): 7522
    System Power Settings:
    AC Power:
    System Sleep Timer (Minutes): 0
    Disk Sleep Timer (Minutes): 10
    Display Sleep Timer (Minutes): 20
    Automatic Restart On Power Loss: No
    Wake On AC Change: No
    Wake On Clamshell Open: Yes
    Display Sleep Uses Dim: Yes
    Battery Power:
    System Sleep Timer (Minutes): 5
    Disk Sleep Timer (Minutes): 10
    Display Sleep Timer (Minutes): 1
    Wake On AC Change: No
    Wake On Clamshell Open: Yes
    Display Sleep Uses Dim: Yes
    Reduce Brightness: Yes
    Hardware Configuration:
    UPS Installed: No
    AC Charger Information:
    Connected: No
    Charging: No
    That's a 41% DRAIN in battery overnight, with it being turned off.
    *Makes appointment at Genius Bar* I'll post results of the visit here just in case anyone else has this problem.

  • Laptop battery not charging/shutting down abruptly

    Hi all,
    I have an Early 2011 Macbook Pro 13". Lately, it's battery is causing me problems. Can anyone point to me the problem. The system info follows:
    Battery Information:
      Model Information:
      Serial Number:    .................
      Manufacturer:          SMP
      Device Name:          bq20z451
      Pack Lot Code:          0
      PCB Lot Code:          0
      Firmware Version:          201
      Hardware Revision:          000a
      Cell Revision:          165
      Charge Information:
      Charge Remaining (mAh):          1619
      Fully Charged:          No
      Charging:          Yes
      Full Charge Capacity (mAh):          4699
      Health Information:
      Cycle Count:          487
      Condition:          Normal
      Battery Installed:          Yes
      Amperage (mA):          2247
      Voltage (mV):          11547
    System Power Settings:
      AC Power:
      System Sleep Timer (Minutes):          0
      Disk Sleep Timer (Minutes):          10
      Display Sleep Timer (Minutes):          15
      Automatic Restart on Power Loss:          No
      Wake on AC Change:          No
      Wake on Clamshell Open:          Yes
      Wake on LAN:          Yes
      Current Power Source:          Yes
      Display Sleep Uses Dim:          Yes
      PrioritizeNetworkReachabilityOverSleep:          0
      Standby Delay:          4200
      Standby Enabled:          0
      Battery Power:
      System Sleep Timer (Minutes):          15
      Disk Sleep Timer (Minutes):          10
      Display Sleep Timer (Minutes):          15
      Wake on AC Change:          No
      Wake on Clamshell Open:          Yes
      Display Sleep Uses Dim:          Yes
      Reduce Brightness:          Yes
      Standby Delay:          4200
      Standby Enabled:          0
    Hardware Configuration:
      UPS Installed:          No
    AC Charger Information:
      Connected:          Yes
      ID:          0x0100
      Wattage (W):          60
      Revision:          0x0000
      Family:          0x00ba
      Serial Number:          0x004505ee
      Charging:          Yes
    Power Events:
    Repeating Events:
      Type:          Wake or Power On
      Time:          12:00 am every day
      Type:          Sleep
      Time:          1:00 am every day

    Hello snavdeep,
    You may want to calibrate your battery.
    Apple Portables: Calibrating your computer's battery for best performance
    http://support.apple.com/kb/HT1490
    Cheers,
    Allen

  • IE had unknown error and after shut down laptop screen is blank

    HP Pavillion dv6t Select Edition Customizable Notebook PC # A2Z58AV
    Windows 7
    IE popped up with a message that there was an error. No other explanation. After shutting down and rebooting, the laptop screen is black but has power.
    No changes made to operating system before this occured.

    Hi @devitojj 
    Welcome to the HP Forums!
    I would like to take a moment and thank you for using the forum, it is a great place to find answers. For you to have the best experience in the HP forum, I would like to direct your attention to the HP Forums Guide First Time Here? Learn How to Post and More.
    I understand that when you power off your notebook it automatically restarts in 4 seconds.
    You have tried several steps to try and resolve this but there is no change.
    As it repeated the behavior with the hard drive removed, you know it is not an issue with Windows.
    You have tried updating the bios and returning it to bios defaults but no change.
    Here is a link from answers.microsoft.com that helped other people with this issue.
    Windows 7 computer restarts automatically after shutdown
    This does suggest you edit your registry which does have the potential to cause issues, so be very careful.  I would also suggest backing up your registry before you attempt it, just in case.
    Back up the registry  from Windows.microsoft.com
    If that has not helped, I would try removing the Cmos or RTC battery for 30 seconds and then replacing it.
    Please let me know if this helped.
    Sparkles1
    I work on behalf of HP
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos, Thumbs Up" on the bottom right to say “Thanks” for helping!

  • Iphone 5c has battery problems and shuts down even after charging, just upgraded to 8.2, no help, what is my next option?

    the iphone 5c still has problems with battery life and shuts down after complete charge.  this happened after 8.1 update, I tried every way to shut things down, still no luck.  what can I do next?

    I did a soft reset, and I went to the discussion and turned every down or off.  This is definitely a hardware problem.
    If you are inquiring about a mortgage application, please click the questionnaire below to begin the process!
    Mortgage Questionnaire<https://webapp.mortgagenetwork.com/BorrowerSite/ManageData1003/StartProcess.aspx ?LO=29015>
    Tom Burke
    Loan Officer NMLS #460277
    Mortgage Network Inc.
    Corporate NMLS#2668
    570-961-5174 direct
    570-313-7366 cell
    Efax 855-795-7084
    [email protected]<mailto:[email protected]>
    www.TomBurkeLoans.com
    2004 Eberhart Rd
    Whitehall PA  18052
    Licensed by the PA dept of Banking and Securities

  • [W520] Does not start on battery only, doesnt shut down or sleep

    Hi all, 
    I have quite a huge problem after flooding my W520 with tea. Obviously immediately after spilling it I flipped the machine, unplugged ac, took out the battery. Few days after laptop didnt start so I had it serviced. The keyboard was changed and whole interior was cleaned. At home I tried to power on the laptop (with battery only) but with no reaction, then plugged ac and computer started itself (I didnt press the power button). When it starts it is possible to unplug the ac, and it works on battery. 
    Second problem is that the machine doesnt want to powerr off or sleep. It shuts down for 2-3 second then automatically starts (both on ac and when already started with battery). To shut down I have to take out the battery and ac. (Tried all possible stuff, WOL, Always on mode and so on but nothing works) ;/
    Called the service with explanation but nobody seemed to know how to fix it. If you have any ideas that could solve the problem please help...

    Hi,
    Welcome to Lenovo Community Forums!
    I’m sorry to hear that you spilled tea in your Lenovo ThinkPad W520 and you are facing multiple issues with the system.
    I would suggest you to perform Flee Power – remove the battery and any other peripheral device connected to the computer. Hold the power button for 10-15 seconds and then connect the AC Adapter and battery and try to turn ON the computer.
    I would suggest you to update BIOS to the latest version, try swapping with a good known AC adapter and battery.
    Basically there's 3 power sources for the motherboard ac adapter, laptop battery and CMOS battery. If either of them goes bad or is malfunctioning you might experience strange behavior. If you have confirmed the functionality of the above said, it probably points to a system board failure.
    Regards,
    Mithun.
    Did someone help you today? Press the star on the left to thank them with a Kudo!
    If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
    Follow @LenovoForums on Twitter!

  • X240 No Power After Shutting Down Windows

    I'm working on X240 Thinkpad which is not powering-up. After replacing the planar it booted but after shutting down Windows, it won't power-up again. I notcied that it powers on again after reseating all battery including the (CMOS battery), but is dead again once you shutdown windows. BIOS FW is updated and its passing the self test. Pressinng the reset button thru pin hole does not solve the issue. It always need resetting all battery (CMOS battery included). Problem does not occur when the thinkpad is not booted to windows and shutdown via power button only. Thanks in advance. Please note that the planar has been replaced for the 2nd time in the span of around 2 months.

    I've had a similar problem with the laptop before this one. I could tell you to try to take the battery out and hold down the power button for 5 seconds and then put the battery back, but that probably won't work. I could tell you to hold down the altcommandp or o and try to reset the ram, but that won't work. Your issue sounds like the power supply and your laptop is most likely dead.
    If you bought it from apple.com you will have to return it and deal with the most incompetent customer service people on the planet. Took them 2 months to get my issue resolved.
    I wish you the best of luck.

  • MBP won't turn off after shut down

    My MacBook Pro with upgrade to Leopard is staying hot after shut down. I am having to remove the battery to make sure, otherwise I have one red hot laptop when I open up my backpack. Is this another Leopard issue?

    Good morning,
    No, this isn't an issue I experience with Leopard...
    I'd try [Resetting your MacBook Pro System Management Controller (SMC)|http://docs.info.apple.com/article.html?artnum=303319] and see if that solves your issue.
    Hope this helps! 
    David

  • Heavy Battery Drain after updating to 8.1 Lumia Cy...

    After updating my Lumia 1520 to 8.1 Cyan update, the battery drain is very high. The battery is lasting only for 6 to 7 hours when the data traffic is on  (under  mixed use of 2G and 3G modes). I have noticed few other users were also experiencing heavy battery drain after the Cyan update.
    Will there be an update to fix this battery drain issue?
    When the phone was in WP 8 Lumia Black update, battery backup was around 24-30 hrs (when data traffic was on).
    What will be the workaround for this?
    Moderator's note: We have provided a subject-related title to help other forum users easily view and respond to this post.
    Solved!
    Go to Solution.

    Yep, my 1520 battery drains like a helicopter that's lost it's rotor after this 8.1 update.
    I was just boasting last weekend how awesome the battery life was on this phone, I drove 300mi with the GPS w/navigation, did some tethering to my laptop for work, went overnight..no charging, used lightly all the next day, few pictures, email, browsing, phone calls, and drove 300mi back on GPS/navigation and I still had 38% battery left.
    I updated to 8.1 sunday night, and on my normal commute to a customer in another state, which under 8.0 would have drained oh...mabey 4-5%, I was at 62% by the time I got to this customer yesteday.
    All I did was make a phone call, that's it. All background stuff is not allowed. location off, cortana off, ...still drains.
    Bad bad bad news. I'm not seeing much usefull ness out of 8.1, and considering the battery life and no real new features....just gimmicks if you ask me, I'm not sure I want to stay at 8.1 . I'm trying to give it a chance...battery life is still better than my POS samsung androids I've had in the past, but knowing how good it really can be...and no real features in 8.1 (I was hopeing they'd fix the imap email not allowed to map sent/trash/inbox issue)....eshh...what a mess it seems.

  • Enormous battery drain after 3.01 upgrade

    guys and gals,
    anyone of you experiencing a huge spike in battery drain after upgrading to firmware 3.01? On 3.0 my iphone 3gs had no probs but after my upgrade last night he ran out of juice within a few hours while I was sleeping. This morning I recharged it but an hour later the phone is allready down to 80% and feeling warm. I guess there is something running in the background but I cant figure out what. Turning the phone on/off doesnt seem to do a thing. Any ideas or personal experiences?

    I did what you said in your 2nd post, and recharged the battery. after 6 hours, it was the charge was still at 100%!
    then I used an app, IM+ Push for a few minutes and had disabled the Push functionality before quitting it. after an hour, I noticed that the battery issue was back. so deleted the said app, and the battery levels returned to normal.
    This evening I re-installed the app, disabled the push functionality again and made sure to set my IM account to off before quitting. the problem hasn't re-occurred since then.
    hope that this helps someone else who's having the same issue.

Maybe you are looking for

  • Why can't thunderbird access my mail anymore after traveling to a different country?

    Hello everyone, I started having problems with Thunderbird after moving from Germany to Lebanon. First I thought it was because I changed my time zone on the computer but now I think it is more related to my yahoo account. First Thunderbird started t

  • Recommend a Free Mail Server (Windows)

    Hi, Can somebody recommend a free mail server that I can use when running demo's / POC's / Training etc from my local machine for use with Delivers. There seems to be a few out there - I'd be interested if anybody can advise there experience with any

  • MS SQL Server Migration Errors

    Attempting to migrate from a Microsoft SQL Server Database to a Oracle database, perform all requirements in the tutorial <?xml version="1.0" encoding="windows-1252" standalone="no"?> <log> <record>   <date>2015-04-29T13:48:50</date>   <logger>oracle

  • Naming clips or subclips

    I have looked extensively through both the manuals and the posts but still need to get something clear in my mind. I have been editing on other systems for many years. I tend to do a lot of my cutting and making clips on the timeline - it may not be

  • PARTATION IN 7.0?

    hi friends, in rsa1 cube change - extras-db performance- partation. for me its showing disable mode, how can i get into enable  and partation? regards suneel.