Lasejet 1102w plus airprinter issues plus home networking config

I have printer HP Laserjet 1102w in my wireless network as follows:
192.168.1.1 ADSL Modem in my bedroom --> 192.168.1.2 TPLINK TL-WR941ND in my bedroom --> 192.168.1.3 TPLINK TL-WR1043ND (AS A REPEATER) in my office in another floor of my house. The printer is in my office.
The printer works just fine using my notebook. I can print everywhere.
But when trying to print from an Ipad or Iphone, I cannot print from my bedroom. No printer is shown in airprinter (ipad/iphone). 
When both ipad or iphone gets repeater signal (far away from 192.168.1.2 TPLink Router) the printer shows in airprinter
So I cannot print from my bedroom when using ipad/iphone.
What am I doing wrong?
I would like to print everywhere using my ipad/iphone. Is there any config to make in 192.168.1.2 router?
The printer has static IP 192.168.1.11
Thanks in advance.
This question was solved.
View Solution.

This is because the printer and the iOS devices have to be on the same network, if one is on the primary and one is on the repeater it will likely not work. As I mentioned above that AirPrint often does not work on repeaters or on hotspots due to how they interact on the network. 
-Spencer 

Similar Messages

  • IPhoto library mapping issues on home network

    Ladies and Gentlemen,
    I have my iPhoto 8 library stored on PowerMac G4 that acts as media server for the house. Each Mac automatically mounts the media drive when the appropriate user logs in and each copy of iPhoto has been 'mapped' to the iPhoto library located on the media server.
    The problem - occasionally, and I can not figure what causes it - but when my wife logs in and opens iPhoto, she gets the good old "Please select the library or create a new one" window. Bless her heart, I've tried to explain how to 'remap' the library - but it's just....well, lets just say I have failed in my communications and explanations.
    So - why does this library mapping 'unmap' and how can I force it to stay 'mapped'??? I've tried several Automator actions and even tried the Record function - no dice.
    Any ideas would be much appreciated because she's on the verge of firing the home network administrator which equates to a reduced IT budget in the future.
    Thanks for your time!
    jc

    John:
    Are all the Macs using the same library? Is this a wireless network or hard wired?
    The library can get unmapped if iPhoto is launched with the server not mounted and accessible.
    Do you Twango?
    TIP: For insurance against the iPhoto database corruption that many users have experienced I recommend making a backup copy of the Library6.iPhoto database file and keep it current. If problems crop up where iPhoto suddenly can't see any photos or thinks there are no photos in the library, replacing the working Library6.iPhoto file with the backup will often get the library back. By keeping it current I mean backup after each import and/or any serious editing or work on books, slideshows, calendars, cards, etc. That insures that if a problem pops up and you do need to replace the database file, you'll retain all those efforts. It doesn't take long to make the backup and it's good insurance.
    I've created an Automator workflow application (requires Tiger), iPhoto dB File Backup, that will copy the selected Library6.iPhoto file from your iPhoto Library folder to the Pictures folder, replacing any previous version of it. It's compatible with iPhoto 08 libraries and Leopard. iPhoto does not have to be closed to run the application, just idle. You can download it at Toad's Cellar. Be sure to read the Read Me pdf file.

  • Officejet Pro 8600 Plus using wireless on home network with Win 7OS

    When troubleshooting the fix will not be apply to turn on the print spooler when problem detected.
    The error code is #1722,Failed to add port monitor HP Discovery Port Monitor.
    What do I do to fix this?  The original installation in October 12 everything was working fine.  Then an outsider extensive virus removal and that is that for printing from computer.  HELP.   I am not a novice but almost and when it comes to port direction, I am lost.  thanks for your help!

    Hi,
    It seems that some of the windows setup files are missing. Do the following things in order.
    1. Uninstall the hp software either going through Start->All Programs->HP->Officejet 8600->Uninstall
    or from the Start->Control Panel->Add remove features
    2. Now go to temp folder.. start->run-> and type %temp% and click ok.  Now delete all the files from the temp folder
    3. Restart the computer
    4. Download the latest software from hp.com 
    http://h20000.www2.hp.com/bizsupport/TechSupport/S​oftwareIndex.jsp?lang=en&cc=us&prodNameId=4323647&​...
    5 run the downloaded file to install the software.
    Hope it will resolve your issue
    Click on the "Thumbs up"button on the left to say "Thanks"
    Please mark the post that solves your problem as "Accepted Solution"
    (Although I am employed by HP, I am speaking for myself and not for HP)

  • BT Netprotect Plus and Home Network.

    I have just upgraded to BT Infinity and BT Netprotect Plus. My old Desktop, with LAN, and my Netbook ,wireless, both run Windows XP and previously had Mcafee Internet Security on both. Prior to the 'upgrade' the home network was fine. Now in lets call it 'Mcafee', Home Networks, My Home Network, the Desktop sees the Netbook as having an 'old' version of Mcafee although it has been uploaded three times, the latest today. This stops me in my tracks trying to get the network working again. BT Help was no help, apart from, offering to charge me to sort out something which was no problem before. Any good ideas out there?
    Solved!
    Go to Solution.

    There's more here - an ageing thread but still applies.
    You can click the white star next to this message if you think it was helpful.

  • BT Netprotect plus home network problem

    I am having real problems with my home network when Netprotect plus is installed, which BT have been unable to resolve.
    My network consists of two PCs running XP with service pack 3, a Netgear NAS drive, a laptop with Vista and a home hub 2.
    All computers have file sharing set up correctly, no computer names are duplicated, all have the same network name set etc.  All devices show up on the network but I cannot read or open files on the different PCs and the laptop. The only device that I can open files on is the NAS drive - which clearly does not have NetProtect plus on; the NAS drive cannot however access my PCs for backing up purposes.
    We have tried everything; permitted IPs are all set up correctly but even switching off the firewalls in NetProtect plus makes no difference, nor does removing and reinstalling NetProtect plus.  If I remove Netprotect plus from a particular PC then other devices on the network can access that PC perfectly normally - indicating that the problem lies with NetProtect plus.
    The only solution would seem to be to move to another antivirus/netprotect programme.  But if anyone has any other ideas that would be much appreciated.
    Ian

    A postscript:
    In the end I gave up on Netprotect plus and installed Kaspersky on the main PC, leaving Netprotect plus on the rest of the network. Kaspersky works perfectly. The other machines on the network can read and copy files from the machine running Kaspersky, which is what I needed. The reverse operation does not work, ie I cannot open and read files on the machines running Netprotect, but this does not cause me any problems. Incidentally, BT support were unable to sort out the problem!!

  • Running ISQL Plus over a home network

    I have a small wireless home network (3 machines), and installed Oracle 10g on one machine. ISQL works fine on this machine. However, I would like to be able to run queries from the other machines using ISQL PLUS.
    Have tried, //<<machinename>>:5560/isqlplus, but this returns a message that the requested page cannot be found.
    I’ve pinged the database host machine from a second machine: ping <<machine name>>, and got a reply but when I pinged the port on the host machine: Ping <<machine name>>:5560, I got no reply. How do I solve communication with this port.
    Any assistance appreciated.
    JH

    Ping <>:5560, I got no reply.Pinging port is not possible. Btw you can't use somthing what is using ICMP protocol (ping) for testing of TCP connection. So use the telnet command for testing of connection.
    P.S: Wrong forum (section) for this type of problem.

  • My HP 6500A Plus is connected to wireless network and web services but won't print email or code

    I have my HP 6500A Plus connected to my wireless network and it is registered on the HP Web Services but it will not print the printer email address or code.  I have followed the directions.  I would appreciate your help in this matter.  Dave

    Hey ddwilson9999,
    If your printer is telling you that it cannot connect to the server, try these steps.
    1. Find your printer's IP address by printing a network configuration page.
    2. Type you IP address into the address bar of your web browser.
    3. Click on the network tab at the top of the page.
    4. Look at the left hand side and click IPv4 under wireless.
    5. Change the IP settings to Manual.
    6. Enter the printer's IP address, your subnet mask, and your routers IP address or default gateway in the spaces.
    7. Set the Preferred DNS to 8.8.8.8.
    8. Set the Alternate DNS to 8.8.4.4.
    9. Click apply.(You may need to refresh the page if it says processing for longer than a min and click apply again.)
    10. Now try to print the information page.
    Although I am an HP employee, I am speaking for myself and not for HP.
    If I have resolved your issue, feel free to provide Kudos and make sure you mark this thread as solution provided.

  • 2 iPads, but can only connect one iPad at a time to my home network.  Is this a known issue with Mac/iPads in general?

    At home I have a HP PC, netbook and Sony laptop with no connection issues.  Last year I bought an iPad 1 for my wife.  This year I bought an iPad 2 for myself.  However, only one iPad can connect to the wifi home network at a time. If I am using the iPad2 then the iPad1 fails to connect to the internet.  if the iPad1 is being used then the iPad2 cannot connect.   I tried resetting iPad network settings for both, reset router, and updated both iPads to latest software/firmware yesterday.  Right now the only iPad that shows any connection is the iPad1.  The iPad2 does not see the home network or any other outside network.  Any suggestions or ideas on how to resolve this?  It is odd the network issues only affect the iPad's.

    @dananova,
    It sounds like you need to either increase the number of dynamic IP addresses your router will hand out or change some of your devices to static IP addresses. 
    Check the router manual on how to change the dynamic IP range of your router.  If you don't have a manual, you can go to Belkin's website and download it.
    To change the IP address of your iPads to static addresses, go to Settings > Wi-Fi and tap the ">" next to the name of your wireless network.  DHCP should be highlighted.  Write down the all the settings on the screen. Next tap the Static button.  Enter the exact same information that you copied from the DHCP screen with the exception of the last 3 digits of the IP address.  Enter a new 3 digit number in this spot.  Generally the original IP address will end with a low number such as 009, so pick a number that is not that low but less than 255.  I would suggest a range of 240 to 250, unless the original IP range falls near this range.  Also make sure you use a different 3 digits for each device you set to use a static IP address.

  • Wifi keeps scanning and dropping even after connected to home network.  Never had this issue until the update, and now my phone runs slow and terrible.  Horrible update!!  Any ideas on a fix?

    Wifi keeps scanning and dropping even after connected to home network.  Never had this issue until the update, and now my phone runs slow and terrible.  Horrible update!!  Any ideas on a fix?

    It's important that you have a steady WiFi connection, ZealousEdge. What phone do you have? Is your phone unable to connect to any WiFi network? If you can, please try deleting the saved WiFi network and re-adding it.
    AndreaS_VZW
    Follow us on Twitter @VZWSupport
    If my response answered your question please click the "Correct Answer" button under my response. This ensures others can benefit from our conversation. Thanks in advance for your help with this!!

  • Issue with 10.9.2 looking NAS drive away from home network

    I have a NAS drive on my home network. When I am away from my home network my MBP running 10.9.2 keeps looking for and not find ing the drive. It keeps interupting my work flow every few minutes. How do I resolve this issue? it is very annoying.

    As a temporary workaround, of course, you can just turn Time Machine OFF.
    There was a similar message, with reference to type "file" in the URL, but this one is differnent.
    Have you ever used a 3rd-party utility, or followed any instructions to edit some files, to change Time Machine's default behavior?

  • How to connect to SQL*Plus and issue a query all in one command?

    Hi everyone,
    Does anyone know of a way to connect to a db with SQL*Plus, and issue a simple query, all with one command?
    I know that I can save a .sql script with a query, then do this:
    sqlplus user/pwd@db @myscript.sql
    But I'm wondering if there's any way to put the actual query right into the connect command, something like:
    sqlplus user/pwd@db "select count(*) from dba_tables;"
    Does anyone know of a way to do this?

    you didn't mention windows or unix. so, here's a link with both
    Re: windows sql script
    it also has a link to another thread on how to deal with the parens when using ehco in dos.

  • OJ Pro 8600 Plus Printing issues

    On this for hours and hours, never had so many issues with setting up a printer.  I am dizzy.  Have a few laptops (macbook Air, Pro) and hardwired Mac Pro (intel) and (PPC).  All OSes are 10.95 (except the PPC which is 10.5.8).  Router is DLink, and a dumb Hub - Netgear.  I assumed that simply connecting the 8600 via ethernet directly to the router, and setting a static IP 192.168.0.100 would be easy.  All seemed OK, as all the computers could access the printer via the brower.  Set-up in Printer/Scanner - System Prefs, went without a problem.  Recognized it just fine.  After a few tries of not printing, I noticed that the set-up DEFAULTS to Airprint driver (version 2.0), so I CHANGED to the HP Officejet Pro 8600 Driver (version 4.1).
    On one laptop, it prints.  On another laptop it does not.  On the Mac Pro it does not.  When printing it locates the printer, spools and states 100% complete.  Over the hours, sometimes it sticks with the 100% complete.  Just now that message disappeared - but in all cases it does not print.  I have been able to get each of the computers to print at various times, but never more than 1.  I think I have it, then try another computer, and it does not work.  I have unplugged the router, unpluged the printer, waited the 20-30 seconds (how stupid is this) a half dozen times.  I have re-started each of the computers as well a few times here and there.  I have re-set the Mac OSX printer System (in the sys prefs - Control + Select PRinter) a few times.  Of course been on the forum and finally gave up.  
    Maybe the 8600 doesn't like the static IP, so I re-did the whole lot with the wireless set-up.  Unplugged the ethernet from the 8600.  Made all the changes with the 8600, logged on to my wireless.  All OK, but still the same issues.  Turned off the router, off the printer, then on the router, printer and computers.  Still problems.  I say "all OK" because I can connect to the printer though the browser.  I can printer a test page though the browser.  In the OSX pref I can select and add the printer quickly.  I can see the ink status in printer window.  The CONNECTION IS THERE.
    I live on the 9th floor of an apartment complex.  Would someone care to help before this worthless piece OS falls out the window.  Thanks

    Hello MrConfetti,
    Welcome to the HP Support Forums!
    That is a very informative post, no one could ask for a better explanation of an issue. After reading, my thoughts / concerns are;
    The Router and Hub
    The apartment complex
    Even though the computer can see the printer on the network, and you can access the printer via the I.P address in your browser, I believe the Hub is blocking the full communication. In order to test this, simply unplug the the hub, power off the computers and printer, then back on, try printing upon start up.
    Regarding the apartment complex, there is probably MANY other wireless signals. These other wireless signals, if using the same Channel you are, can be causing information to be block. Print out a Network Configuration Page from the printer. On the report, review the other network's channels. Change your router's channel to one not used, or less used.
    Network Config Page is printed by touching the Wireless icon> Settings.
    Lastly, If the above thoughts / suggestions fail to provide a working connection, try using the printers Wireless Direct. I only offer this idea as a means of troubleshooting. The printer can have up to 5 connections to it's Wireless Direct. Connect each computer, add the printer, try to print.
    Wireless Direct is enabled by touching the Wireless icon> Settings> Wireless Direct.
    I hope to hear back with good news.
    JERENDS
    I work on behalf of HP
    Please click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos Thumbs Up" to the left of the reply button to say “Thanks” for helping!

  • When I open my mail account I keep getting the message "Checking for Mail". I deleted the yahoo account and set it up again and I am still getting the same issue plus I am not seeing any of my mail or folders. Can anyone help?

    When I open my mail account I keep getting the message "Checking for Mail". I deleted the yahoo account and set it up again and I am still getting the same issue plus I am not seeing any of my mail or folders. Can anyone help?

    This is how I fixed it on my new iPhone 5S. Using the standard yahoo setting on my phone.
    You will have to access  "managing your app passwords" on your account profile for yahoo. Generate password for your app. For example: "My iPhone 5S'
    Go to your Iphone and set up your yahoo mail account on your phone the normal way and you have to use the generated password.  instead of the yahoo account password.
    source:
    http://virtualizeme.net/iphone-5-yahoo-mail-server-unavailable-fix/
    I hope this helps,
    cheers

  • Can I configure a wireless home network with two cable routers (both with separate connections to the same cable company)?  Issue is poor signal strength even with multiple Airport Expresses added to the network.

    I have a wireless home network consisting of a time capsule, two airport expresses and a cable modem.  Even with this configuration I get a very weak signal in much of be condo - the walls, etc. are solid concrete. I want to see if I can add another separately connected cable modem and connect one of the existing airport express to it by Ethernet cable.  If so, this would give me two wired hubs and greatly improve signal strength. I do not know if this configuration will in fact work or if I will just wind up with two, separate and unrelateable networks.  Unfortunately, there is no way to run any additional Ethernet cable and I doubt simply adding more Airport Express will help. Thanks.

    Try Ethernet over Power adapters.. these are very popular for your kind of environment.. being able to make non-wireless link to another area where you can setup a wireless access point.
    Airport Express are not great for wireless power.. if you really have issues with wireless strength in a bad environment apple stuff is not the way to go.
    The comparison chart here.
    http://www.smallnetbuilder.com/lanwan/router-charts/bar/58-2_4-ghz-dn?see=P_F
    This is their worst test location you can also see averages.. the latest airport extreme.. is there a long way down.. and that is a much better wireless device than Airport Express.
    The Ubiquiti power AP is small cheap and designed for precisely this duty.. useless in an apple wireless network.. you will need to run ethernet or EOP adapters back to the main router.. but if the normal omni directional antennas don't provide enough signal you can get directional ones.. I suspect you can cover your whole apartment with a pair of these and high gain directional antenna.

  • Why did text message freeze? had to turn off phone and restart it to work. plus why do i get network errors on facebook app?

    why did text message freeze on my iphone4s? had to turn off the cell then turn on to work normally again. plus why do i get network errors on my facebook app?

    why did text message freeze on my iphone4s? had to turn off the cell then turn on to work normally again. plus why do i get network errors on my facebook app?

Maybe you are looking for