Layer 3 Error

Hi all,
I am consistently getting the following error on my voice gateway.
ISDN Se0/0/0:15 **ERROR**: L3_BadPeerMsg: event 0x75
My voice gw is connected to an Avaya PBX.
Has anyone got any clues what went wrong?

Hi,
That is the output from "debug isdn q931" itself. The remote caller is not able to hear me eventhough I can hear him clearly. I am not sure if the above error is the culprit.
Regards.

Similar Messages

Getting "layer break" error message when trying to Preview a single sided DVD, or build an ISO image or disk folder

Hi! Hoping someone might be able to help with an odd problem. I haven't found anything in the forums or the web that match my symptoms.
I've been using Encore CS6 (v6.0.1.013) on a MacBook retina over the past year to successfully create a number of single sided DVDs with menus, chapters, and all that. I usually make a copy of a previous DVD project, and then replace video assets with the new files and transcodes, move and rename chapter markers, and rework the menus in Photoshop. I then will build ISO images for both DVD and Blu-Ray (both single-sided), and use those to burn many copies of each DVD for clients.
This week, while developing one of these projects, when trying to build a DVD ISO image that looked like it would fit on a 4.7 GB DVD, I received the "layer break" message ("The chosen layer break does not satisfy dual layer requirements. To fix this, either set a new layer break manually, or choose to set layer break automatically.") because (I'm guessing) the material was too long for the 4.7 GB DVD (the Build screen now shows about 5GB of material are in the project). This is the first time I've seen that message - usually Encore just tells me the material is too big for the DVD.
I re-transcoded the material down to well under 4.7 GB (about 3.9 GB), reverted and replaced the transcoded files, and now the DVD build screen shows that there are about 700MB free on a 4.7 GB DVD. But I still have not been able to build any version of the DVD (image, folder, disc), without getting the "layer break" message. I also now get this same layer break message when trying to "Preview from Here" any menu, killing my ability to preview the DVD menus in Encore.
Just to see what would happen, I chose an 8.4GB Dual Layer DVD, and chose "manual" instead of "automatic" for the layer break selection, but never got the layer break selection dialog box, just the "layer break" error message.
I typically build both DVD and Blu-Ray images from the same material in the same project. I use different transcoding settings for each, and I have been able to build a Blu-Ray ISO without this "layer break" error on the Blu-Ray build (which is about 24.5GB when built). And as I mentioned before, this is the first project on which I've even seen this layer break message.
Any suggestions would be greatly appreciated! I'd rather not recreate the project from scratch, but I'm worried that I may have to.
Thanks
Jon

The total project being small enough may mean you have one layer that is too big. Both layers have to be smaller than half the disk, right?
Be sure you "run as administrator" for dual layer projects.
Encore may set the layer break correctly if it finds a good place, but there are numerous complaints about it being unreliable.
Build to a folder (no layer break is set), then use ImgBurn to build and ask to be prompted for layer break. ImgBurn is also unreliable under some circumstances.
The most frequent problems appear to be when there is no good location for a break. Do a search for "layer break imgburn" and you will see a variety of strategies.
http://forum.imgburn.com/index.php?/topic/1777-how-to-create-a-double-layer-dvd-video-imag e-file-using-imgburn/
Also see these posts:
Neil Wilkes
http://forums.adobe.com/message/3466255#3466255
Neil Wilkes
http://forums.adobe.com/message/4054265#4054265
Neil Wilkes
http://forums.adobe.com/message/4054269#4054269
Jon Geddes
http://forums.adobe.com/message/4002647#4002647
shuchi shrivastava
http://forums.adobe.com/message/3905911#3905911
Jon Geddes and Neil Wilkes
http://forums.adobe.com/message/4003221#4003221

Security Network Layer (SNC) error when creating new session

in SAPGUI 710, suddenly some users are getting a popup message ("Security Network Layer SNC error") when they use the Create New Session toolbar button.
SSO works fine when they connect from SAP Logon, its only when attempting to open secondary sessions. Also, its only some users.
Where would I find log information resulting from the error? Or any suggestions on steps to troubleshoot?
Thanks!

Hello Erik,
Issue actually belongs to BC-SEC-SNC, not SAPGUI.
The attached note advises how to run a trace to get more information about the issue
150104 collecting dev_trace of user session via SM04
If you recreate the issue again with the active trace, you might have more sucess with a reply.
Just to advise that 7.10 is out of support and 7.20 should be used as soon as possible.
Kind Regards,
Jude

Security network layer snc error

HI All,
We are using Singlr-sign-on method logging to SAP systems.
I started getting "security network layer snc error" when i am opening second window.
I have deleted all the old SAP short cuts and also tried to logon to the SAP application via "Start -->Programs -->SAP Frontend -->SAP Logon".
Still I am getting the same error.
Please provide me any suggestion to avoid this.
Thanks in advance
Joginadham U

Hello,
The mentioned error: "Security Network layer (SNC) error" only tells that there is problem for SNC.
To obtain more information on the error, you could create a trace as per SAP note 495911. SAP Note 150104 may be also useful.
Maybe in the Security forum you can find more assistance.
Regards,
Désiré

DVDSP4 build to Primo DVD-will it work around layer break error ?

I tried to create layer breaks because under the build option automatic won't burn and manual breaks are greyed out. so i can't burn and i need to get this done before sunday. the build to my hard drive works perfectly and if i test the DVD video folder using DVD player, it works great. If I move the Video & Audio DVD folders to my PC and use Primo DVD and burn a DL disc, will the layer break errors in DVD Studio Pro cause problems during the playback of a disc burned with Primo DVD? Basically, will these DVDSP4 errors carry over no matter what burning program I use; Toast, Primo, Record Now??

http://discussions.apple.com/thread.jspa?messageID=4078067&#4078067
(I also mentioned this just now in the other thread just in case)
Anyway you will need a proper break point, not sure (have not used) Primo so do not know if it will throw a break point in somehow or not, but if you go to the above thread works through the issues for you

Video transition on Adjustment Layer causing errors

I have video transitions (native, not plug-ins) on an adjustment layer without any effects. When playing, the video freezes on the last frame before the transition and then continues playing after the end of the transition. The transition does nothing but hold that frame. Also, if I try to render the work area or export, I get the "Error compiling movie: Unknown error". If I remove the transitions, things work ok.
Starting a New Project and importing the old one did nothing to fix the problem.
I've got plenty of RAM and HD space, please help.

Then...why are you using one. Just apply the transitions directly to the clips.
I did this to discover why another project was producing the "unknown error" when rendering and exporting. I kept everything clean changing one variable at a time on a new project: clip sources, resolutions, transitions, effects, adjustment layer, etc.
If rendering the sequence works, then that is the appropriate solution. Do you have a red line above the timeline indicating that you need to render? Or do you need to set the opacity at 99% - AND - then render to make it work.
Simply changing the opacity to 99% worked, no need to render.
Just out of curiosity, why are you putting transitions on an Adjustment Layer? I can't think of a reason, but then again, I use transitions between nested sequences a lot. Maybe it is in place of that?
An effect in an adjustment layer is jarring if its transition does not match one applied between clips.

Dual Layer DVD error

Hi,
For the first time I am burning a Dual layer DVD.I have a video with file size of 8.1 Gb. When I insert to burn it on DVD 09, it gives me an error" Please insert a recordable media". I am using Verbatim DVD+R DL. Is there any relation between the DVD drive, Hardware or DVD-R?
Any ideas?
Thanks.
MANDAR

Is your DVD drive a DVD+R DL compatable? I've had good luck with those discs with the Lacie (NEC) and the Pioneer (forgot the model, it's the newest.)
Rikk

MapViewer tile layer preview error in OBIEE 11.1.1.7

Some folks have run into an issue when previewing tile layers in the manage tile layers page of MapViewer in obiee 11.1.1.7 (i.e. in the mapviewer deployed on wls in obiee).
If you get a 500 - internal server error when trying to view map/manage tiles from the Manage Tile Layers page then you have to apply the workaround/fix described in the mapviewer 11.1.1.7 readme
Known issues =============================================
- On certain WLS domains (mostly when ADF run-time library is deployed), you
may see errors when trying to preview tile layers. To fix this issue, modify
the weblogic.xml descriptor file found in mapviewer.ear's WEB-INF/ folder, and
uncomment the entry for the jstl 1.2 library as shown below (note the jsf
section should remain commented-out):
<library-ref>
<library-name>jstl</library-name>
<specification-version>1.2</specification-version>
</library-ref>


Hi Cristian,
You must use '' at script when call some column value. (use '@1' instead of @1)
Tip.. note you can use your "WebMessage Name" (from your script, like "filling", "machine_filing") into your analisys.
Hope this help
Felipe Idalgo

Layer mask error in photoshop

I have made a video, I've tried everything I can think of.
It doesn't happen all the time, or the same layer set up. I'll be editing a layer, and all of a sudden a layer mask is activated, and it erases everything. All my layer info is still there, but a mask is active.
If I make no sense, watch the video, apparently I'm the only one on planet earth with this problem, I've never found anyone else with this issue.
Yes, I've tried defaulting the preferences
Yes, I've tried turning on basic mode.
Nothing works!
Paint Tool SAI is looking awfully awesome right now.

Here's the PSE 7 help page. As Mark states in his post, it's Layer<Group with Previous. I would assume the tutorial must have been written with PSE 8 in mind.
http://help.adobe.com/en_US/PhotoshopElements/7.0_Win/WSae2ea3b149d0c3591ae939f103860b3d59 -7f85.html
Adobe changed the command's name from clipping group to clipping mask. They work the same exact way only the name is different. *Keep this name change in mind when you watch or read tutorials on the web.
I think this command's name change was made to help match commands between various Adobe products.

Status 51 Error in ALE IDOC

Hi,
Iam trying to send a MATMAS Idoc from one client to another client , which is in the same R/3. The outbound staus is 03 and the inbound is 51.
I just created a material (Material details are attached below for reference) and send tht material to the other client using BD10.
can you please tell me the Inbound function module name which i should use to post it again.
Material Name:KRMATERIAL
Industry sector : Mechanical Engineering
Material Type : Finished Products.
Base unit of measure as KG.
Gross Weight as 200.
Net Weight as 100.
Weight Unit as KG.
Thanks
-Karthik

Hi Karthik,
Just follow the procedure, this is for MATMAS
Sending System(Outbound ALE Process)
Tcode SALE ? for
a) Define Logical System
b) Assign Client to Logical System
Tcode SM59-RFC Destination
Tcode BD64 ? Create Model View
Tcode BD82 ? Generate partner Profiles & Create Ports
Tcode BD64 ? Distribute the Model view
Message Type MATMAS
Tcode BD10 ? Send Material Data
Tcode WE05 ? Idoc List for watching any Errors
Receiving System(Inbound ALE )
Tcode SALE ? for
a) Define Logical System
b) Assign Client to Logical System
Tcode SM59-RFC Destination
Tcode BD64 ? Check for Model view whether it has distributed or not
Tcode BD82 -- Generate partner Profiles & Create Ports
Tcode BD11 Getting Material Data
Tcode WE05 ? Idoc List for inbound status codes
ALE IDOC Steps
Sending System(Outbound ALE Process)
Tcode SALE ?3 for
a) Define Logical System
b) Assign Client to Logical System
Tcode SM59-RFC Destination
Tcode BD64 !V Create Model View
Tcode BD82 !V Generate partner Profiles & Create Ports
Tcode BD64 !V Distribute the Model view
This is Receiving system Settings
Receiving System(Inbound ALE )
Tcode SALE ?3 for
a) Define Logical System
b) Assign Client to Logical System
Tcode SM59-RFC Destination
Tcode BD64 !V Check for Model view whether it has distributed or not
Tcode BD82 -- Generate partner Profiles & Create Ports
Tcode BD11 Getting Material Data
Tcode WE05 !V Idoc List for inbound status codes
Message Type MATMAS
Tcode BD10 !V Send Material Data
Tcode WE05 !V Idoc List for watching any Errors
STEP 1)a Goto Tcode SALE
Click on Sending & Receiving Systems-->Select Logical Systems
Here Define Logical Systems---> Click on Execute Button
go for new entries
-System Name : ERP000
-Description : Sending System
-System Name : ERP800
-Description : Receiving System
press Enter & Save
it will ask Request
if you want new request create new Request orpress continue for transfering the objects
B) goto Tcode SALE
Select Assign Client to Logical Systems-->Execute
000--> Double click on this
Give the following Information
-Client : ERP 000
-City :
-Logical System
-Currency
-Client role
Save this Data
Step 2) For RFC Creation
Goto Tcode SM59-->Select R/3 Connects
Click on Create Button
RFC Destination Name should be same as partner's logical system name and case sensitive
to create the ports automatically while generating the partner profiles
give the information for required fields
RFC Destination : ERP800
Connection type: 3
Description
Target Host : ERP000
System No:000
lan : EN
Client : 800
User : Login User Name
Password:
save this & Test it & RemortLogin
STEP 3) Goto Tcode BD64 -- click on Change mode button
click on create moduleview
short text : xxxxxxxxxxxxxx
Technical Neme : MODEL_ALV
save this & Press ok
select your just created modelview Name :'MODEL_ALV'.
goto add message type
Model Name : MODEL_ALV
sender : ERP000
Receiver : ERP800
Message type :MATMAS
save & Press Enter
STEP 4) Goto Tcode BD82
Give Model View : MODEL_ALV
Partner system : ERP800
execute this by press F8 Button
it will gives you sending system port No :A000000015(Like)
STEP 5) Goto Tcode BD64
select the modelview
goto >edit>modelview-->distribute
press ok & Press enter
STEP 6) goto Tcode : BD10 for Material sending
Material : mat_001
Message Type : MATMAS
Logical System : ERP800
and Execute
STEP 7)goto Tcode : BD11 for Material Receiving
Material : 100-300
Message Type : MATMAS
and Execute --> 1 request idoc created for message type Matmas
press enter
Here Master Idoc set for Messge type MATMAS-->press Enter
1 Communication Idoc generated for Message Type
this is your IDOC
Change Pointers
how to change the description of a material using ALE Change Pointers.
I will give the following few steps
1) Tcode BD61---> check the change pointers activated check box
save and goback.
2) Tcode BD50---> check the MATMAS check box save and comeback.
3) Tcode BD51---> goto IDOC_INPUT_MATMAS01 select the checkbox save and comeback.
4) Tcode BD52---> give message type : matmas press ok button.
select all what ever you want and delete remaining fields.
save & come back.
5) 5) go to Tcode MM02 select one material and try to change the description and save it
it will effects the target systems material desciption will also changes
6) goto Tcode SE38 give program Name is : RBDMIDOC and Execute
give Message type : MATMAS and Executte
ALE/IDOC Status Codes/Messages
01 Error --> Idoc Added
30 Error --> Idoc ready for dispatch(ALE Service)
then goto SE38 --> Execute the Program RBDMIDOC
29 Error --> ALE Service Layer
then goto SE38 --> Execute the Program RSEOUT00
03 Error --> Data Passed to Port ok
then goto SE38 --> Execute the Program RBDMOIND
12 Error --> Dispatch ok
Inbound Status Codes
50 Error --> It will go for ALE Service Layer
56 Error --> Idoc with Errors added
51 Error --> Application Document not posted
65 Error --> Error in ALE Service Layer
for 51 or 56 Errors do the following steps
goto WE19 > give the IDOC Number and Execute>
Press on Inbound function Module
for 65 Error --> goto SE38 --> Execute the Program RBDAPP01 then your getting 51 Error
<b>Reward Points if this helps,</b>
Satish

Finally determined what causes an "Internal Error Occurred" message in FW

I use Fireworks for creating wireframes. One FW png file may contain many layers
with each layer representing a web page. The intention is to create the png file, and then to export it to a PDF file so that developers can use it to view the pages and to understand page navigation. I learned this technique by watching Jim Babbage's excellent video on using Fireworks for wireframing.
I create hotspots in the FW png file on one layer and use that to point to another layer that represents another web page. The purpose is to show a kind of flow or extra info for the developers. I've been struggling for over a year with an error that would pop up now and then when attempting to save the png file. The error would show "Internal Error Occurred" and I had no idea why this was occurring. I tried multiple things to get rid of the error and recently I finally discovered what was causing it.
It turns out that if you create a FW png file with layers, and you insert a hotspot that points to one of those layers, and then later when editing the FW png file you decide to delete a layer that is being referenced via a hotspot in a different layer, this error will occur. It doesn't occur every time you attempt to save the png file, but it will occur if you save the png file (no error shown), then export to a pdf file, then (as required by FW) attempt to save the png file again. That's when you will see the error for sure.
The cause is a hotspot link that points to a layer that no longer exists. This is most often caused by creating hotspots that point to the layer, then later deciding to delete that layer but you don't go back and remove any hotspot links to the deleted layer. For some reason, FW will let you attempt to save the file and may or many not show the dreaded "Internal Error Occurred" pop-up message. If you were able to save your png file and didn't see the error show up, and then you decide to export the png file to a PDF file, FW requires you to save the png file after the export option completes. It's when you attempt to save it at this time that it will show up for sure if your hotspot points to a deleted layer. The error message won't go away either.
It's kind of a pain if you have a bunch of layers with a bunch of hotspot links, but you will have to click on each hotspot and determine if it points to a layer that exists in the current png file. If that layer doesn't exist, you will have to point to a layer that does exist, or delete the hotspot to get rid of the "Internal Error Occurred" message.
Hope this helps,
Stevebo

After doing further testing, I've noticed that the error can't be reproduced every time a hotspot points to a nonexistent layer. BUT, every time I've encountered the "internal error occurred" message when saving a png file with hotspots and multiple layers, I have found one or more hotspots pointing to layers that no longer exist. Once pointing the hotspot(s) to a layer that does exist, or simply removing the hotspot(s), the "internal error occurred" message goes away.
So in my encounters with this error, finding the hotspot(s) that point to layer(s) that have been removed fixes the problem. The problem is that it doesn't always occur, just sometimes. It may have to do with the number of png files that may be open and the number of layers that exist, or once the error begins showing up. Just not sure, but I am sure of what I need to do to make the error go away in my case (remove hotspots that point to nonexistent layers). So far it's fixed the problem every time.
It would be interesting to see if others encounter this same error and if there is one or more hotspots pointing to deleted layers. It may be that the error message is simply a "catch-all" for errors that can't be determined and this just happens to be one scenario.
steve

Error when executing Webservice in BW

Hi,
I am trying to execute Web service in Web service navigator and i am getting the following error
HTTP/1.1 500 Internal Server Error
content-type: text/xml; charset=utf-8
content-length: 600
accept: text/xml
sap-srt_id: 20100823/155814/v1.00_final_6.40/4C72FD39F2E90095E10080000A754720
server: SAP NetWeaver Application Server / ABAP 701
<soap-env:Envelope xmlns:soap-env="http://schemas.xmlsoap.org/soap/envelope/"><soap-env:Header></soap-env:Header><soap-env:Body><soap-env:Fault><faultcode>soap-env:Client</faultcode><faultstring xml:lang="en">InvalidVariableValues</faultstring><detail><n0:GetQueryViewData.Exception xmlns:n0="urn:sap-com:document:sap:soap:functions:mc-style"><Name>InvalidVariableValues</Name><Text>Incorrect call of OLAP layer CL_RSR_OLAP; error in BW-BEX-ET ()</Text><Message><ID>BRAIN</ID><Number>369</Number></Message></n0:GetQueryViewData.Exception></detail></soap-env:Fault></soap-env:Body></soap-env:Envelope>
I tried to test my webservice in SICF and i get the following soap message
<soap-env:Envelope>
<soap-env:Header/>
<soap-env:Body>
<soap-env:Fault>
<faultcode>soap-env:Server</faultcode>
<faultstring xml:lang="en">
SRT: Wrong Content-Type and empty HTTP-Body received
</faultstring>
<detail>
<ns:SystemFault>
<Host>undefined</Host>
<Component>COREMSG</Component>
<ChainedException>
<Exception_Name>CX_SOAP_CORE</Exception_Name>
<Exception_Text>
SRT: Wrong Content-Type and empty HTTP-Body received
</Exception_Text>
</ChainedException>
</ns:SystemFault>
</detail>
</soap-env:Fault>
</soap-env:Body>
</soap-env:Envelope>
Can any one help me with this issue
Thanks
Surya

Hi,
Thanks for your response. It looks like its throwing Invalid Variable Values error. However my query does not have any variables. I tried it with and without variables but i still get the same error..
Without variables i just entered Infoprovider and Query name. I get the same error. However when i execute function module
RRW3_GET_QUERY_VIEW_DATA with the same input parameters which is infoprovider and query i get my result. Below is the error message
HTTP/1.1 500 Internal Server Error
set-cookie: sap-usercontext=sap-client=210; path=/
content-type: text/xml; charset=utf-8
content-length: 600
accept: text/xml
sap-srt_id: 20100827/091011/v1.00_final_6.40/4C77DAAC123A0095E10080000A754720
server: SAP NetWeaver Application Server / ABAP 701
<soap-env:Envelope xmlns:soap-env="http://schemas.xmlsoap.org/soap/envelope/">
      <soap-env:Header></soap-env:Header>
      <soap-env:Body>
            <soap-env:Fault>
                  <faultcode>soap-env:Client</faultcode>
                  <faultstring xml:lang="en">InvalidVariableValues</faultstring>
                  <detail>
                        <n0:GetQueryViewData.Exception xmlns:n0="urn:sap-com:document:sap:soap:functions:mc-style">
                              <Name>InvalidVariableValues</Name>
                              <Text>Incorrect call of OLAP layer CL_RSR_OLAP; error in BW-BEX-ET ()</Text>
                              <Message>
                                    <ID>BRAIN</ID>
                                    <Number>369</Number>
                              </Message>
                        </n0:GetQueryViewData.Exception>
                  </detail>
           </soap-env:Fault>
      </soap-env:Body>
</soap-env:Envelope>

Unable to create Business Foundation Layer in XI4 IDT using OLAP connection

Hi,
I have created a BICS connection against an SAP BW cube and want to use this connection in order to build a Business Layer in XI4 Information Design Tool. When I try to map this connection to the business layer, it errors out "Error occurred during connection selection - Connection is not supported".
I'm currently using BO XI4 SP1 and SAP BI NW Eh1 SP6.
Can anyone throw some light on how to create a Business Layer/Universe against an SAP BW cube?
Also, can we query ECC systems using the new semantic layer in XI4 from WebI?
Thanks in advance.
Abhi

Hi,
I'm getting the same error. Did you already solve the problem?
Kind regards,
Eric
Edit:
Hi,
i found this in another thread:
[Information Design Tool and SAP BICS|Information Design Tool and SAP BICS;
Seems like SAP doesn't want to enable Universes on OLAP-Connections?!
Regards,
Eric
Edited by: Eric REDLIN on Jun 24, 2011 4:49 PM

Sybase Connection Error - cannot establish database connection

BO Data Services Tool -> Creation of new Data Store -> Sybase ASE
When I tried to create a sybase datastore(New connection), I've got this error message. But I am able to connect to sybase database with client application with same connection parameter. I appreciate if someone come across same issue.
ERROR MESSAGE
*WARNING: Cannot establish database connecton.
u2018Sybase connecton error: <Sybase ASE Server message number <1640> State <2> Severity <16> From Server <tstlS03>: Message Text is:
Adaptve Server requires encrypton of the login password on the network.
Sybase ASE Server message number <4002> State <1> Severity <14> From Server <tstlSO3>: Message Text is: Login failed.
Sybase CS Library message number <6717S468> Severity <4>: Message Text is: ct_connectO: protocol specific layer: external error: The attempt to connect to the server failed.>.u2019 lODI- 1111341)

I tried to create repositories for sybase, it failed. But it succeeded when created datastore. The procedures's as follow:
1. Create ODBC for this sybase connection, and it should display "Connection successful" when you click "Test connection".
(you need to specify several parameters like user id & password, server,database name and file, etc.)
2. Create datastore by using ODBC connection.

Date/Time Field in Access 2000 - INSERT INTO ... syntax error

I am using Labview 6.1 Professional with the Database Connectivity Toolkit. When I execute this SQL Command "INSERT INTO PRODUCTION (Part, Passed, Date) VALUES ('Part#1', 2, '10/10/2003 10:10:10 AM')" I get a Run-Time Syntax Error. If I remove the Date Label and Date Value it works. What is the proper Format of the Date/Time Type Field in ACCESS 2000 for Labview 6.1 SQL? I have seen and tried all of the solutions already posted like MSG 1ZNAJHJ6.

Well, if it's any consolation handling dates is a pain regardless of which database you use. In any case, I created a table with the following definition:
CREATE TABLE testing
(item1 INTEGER,
item2 DATE)
I them did the following insert:
INSERT INTO testing
VALUES (1, '18/11/1953 04:20:00');
And everything worked fine. Note that in the date (my Bday, BTW) the format is DD/MM/YYYY followed by the time.
What exactly is the error you're getting? Can you post the exact text of the error message. Also, I ran my test using the examples that come with LabSQL--not the toolkit.
Mike...
Oops, just noticed something. You have a column name that is probibly a reserved word "Date". Try your insert as:
INSERT INTO PRODUCTION
VALUES
('Part#1', 2, '10/10/2003 10:10:10 AM')
If there is only those three columns and they the order the data appears is the same as the column order, you don't need the column list. If this works (and it should--I just tried it) I would only view it as a temporary patch. The column name should be changed.
This is also a good reason to not use the Access GUI to create tables. If you tried creating a table like that in SQL you would have gotten an error message. Learning to build tables in SQL code isn't hard and it adds an extra layer of error checking that the GUI apparently doesn't think is important.
If you're interested let me know and I can send you the info on a really good book on SQL...
Certified Professional Instructor
Certified LabVIEW Architect
LabVIEW Champion
"... after all, He's not a tame lion..."
Be thinking ahead and mark your dance card for NI Week 2015 now: TS 6139 - Object Oriented First Steps

Layer 3 Error

Similar Messages

Maybe you are looking for