LC 475 won' boot after 13 years of good service

Hi. My LC475 was running 7.5.3, I kept it going because it ran a very good scanner. All Iget when Iturn it on is the happy Macintosh logo and then the logo that indicates that it cannot find the system software. Any ideas?

The Classic II/Performa 200 does have a battery too. It's a 3.6 volt 1/2 AA battery. If the computer has been around for three to five years or more it's probably time to replace the battery. I should know since I recently had to replace my Performa 200's battery (same Mac as far as specs go but by a different name). If you have a multimeter or know someone who does you can use it to check the battery. Anything below 3.1 Volts indicates it's time to replace it. You should be able to find it at Batteries Plus (& at a reasonable price too). Radio Shack may also have it but even if they do I'm guessing they'll probably have worse pricing too (even if they do they may not know it's used in older Macs too; they're quite clueless when it comes to Macs in general; they don't even sell Macs).

Similar Messages

I'm running OS X 10.6.8-Why is Time Machine all of a sudden backing up 225GB of data after 2 years of perfect service? I have not added, deleted, or upgraded anything, Help!

I'm running OS X 10.6.8-Why is Time Machine all of a sudden backing up 250GB of data after 2 years of perfect service? I have not added, deleted, or upgraded anything.

USB 3.0 drives work on USB 2.0 but you do get 2.0 speed. They are cheaper because they are popular PC drives. If you get a new computer you'll get the bump to 3.0 speed.
I like the Seagate USB 3.0 Backup plus drives. They come formatted for PC but easy to format in Disk Utility. Seagate Backup Plus Right now the 1T is more than the 2 & 3T drives
This Western Digital drive has good reviews: WD My Book Hard Drive for Mac 2 TB $99.
Locally, Best Buy seems to have the best prices.
USB 3.0 is 10x faster than USB 2.0
Thunderbolt is 12 times faster than FireWire 800 and up to 20 times faster than USB 2.0.
Format new drives with Apple's Disk Utility rather than the software that come with the drive.
My plan was to rid a lot of the stuff I have on my computer (to a hard drive) anyhow once it had backed up.
I wound't necessarily backup those files to Time Machine. I would copy to the external drive then delete from computer. Only backup to Time Machine the data you would want to restore to your Mac if there was a problem. The backup will go much faster this way. Time Machine backup is slower than just copying data in my experience.

Hyperion Reports Scheduler stopped working after 4 years of reliable servic

Hello,
I'm puzzled by this, but today at 4:00 AM, the scheduler stopped working. I tried to manually restart the service to no avail. I rebooted the server, nothing. I reinstalled Reports (but selected retain configuration), yet nothing. I'm perplexed as this has been working without issues for 4 years. Next step is to check whether the IT group did a patch upgrade of the OS and may have caused this.
If anyone has an idea, pls forward. Many thanks.
Here's the content of the log file:
10-29 04:06:48 INFO JobServiceThread     Batch "Station Reporting\2006 MOR" finished at Oct 29, 2008 4:06:48 AM
10-29 04:06:48 INFO JobServiceThread     Detail status : Batch "Station Reporting\2006 MOR" was started at Oct 29, 2008 4:06:31 AM
Problems encountered in "Station Reporting\MOR\2008 MOR"
ADM Error processing results from query: 1
Batch "Station Reporting\2006 MOR" finished at Oct 29, 2008 4:06:48 AM
10-29 04:23:06 INFO SchedulerServerLauncher     Hyperion Reports 7.0
10-29 04:23:06 INFO SchedulerServerLauncher     Copyright(C)2000-2004 Hyperion Solutions Corporation
10-29 04:23:06 INFO SchedulerServerLauncher     All Rights Reserved
10-29 04:23:23 ERROR SchedulerServerLauncher     Error while starting Scheduler Server

schedule.xml must be deleted if it reaches 8 megs. Surprised that Hyperion did not come with something more intuitive.

BT Infinity 2 - Suddenly no speed after 1 year of ...

I have had a solid 50 meg with 15 up for an entire year. I know this because I stream and upload every day, so if my connection was slow, I would know.
After 1 year of perfect service and being a very happy customer I know am getting 1 meg. What seems so strange is this happened after a heavy night of downloading. I reinstalled like 50 games onto my new PC, downloaded like 500Gig and bam, suddenly I have no speed.
The reason I loved this internet was because I could freely stream and upload/download without caps, thats why I signed up, I asked if they throttle. They said they cant do that as we are on the top package,
It seems to big of a coincidence to slow down right after a lot of downloading. Frustraing.

500gb is huge compared to most and I wonder if you are considered a heavy user in this context
Heavy users: Heavy users can cause peak traffic volumes to exceed the engineered maximum load. In practice this refers to a very small proportion of users of a network whose use is excessive to the extent that it impacts on other users.
If you like a post, or want to say thanks for a helpful answer, please click on the Ratings star on the left-hand side of the post.
If someone answers your question correctly please let other members know by clicking on ’Mark as Accepted Solution’.

$400 down payment refund after a year?

Okay so about a year ago I started a new contract and for the Iphone 4s, they did a credit check and due to my lack of credit they told me I would have to pay a $400.00 down payment. However, I would get this money back after a year of good payments (no late payments are anything I was always on time.)
Okay so I check my history of payments in my account and it showed this
$11.28 deposit interest July 12
$400.00 Deposit July 12
-$304.56 A/P Credit Return July 12
The following day I received a check in the mail from Verizon paid to the order to me for $304.56. It said "Credit refund".
Um if this is my down payment given back to me, where is my other +$90.00?
My down payment like I said was $400.00.

The initial deposit plus simple interest is refunded or is supposed to be refunded but what happens the company takes out for any bills due or upcoming. However it could be a racket, call them up and ask why the shortage. if you did not pay the upcoming invoice take that normal bill due and subtract. it may cime out correct.
However not returning your full deposit with interest, will interest your states attorney generals office. File a complaint with the Attorney Generals Consumer Frauds division. You may also sue verizon in small claims court plus filing fees for the amount not returned.
Deposit payments can be used towards bill payment but as a rule are not allowed especially if you already paid your invoice and have a zero balance or as a final invoice if you are leaving the service provider. Like I said if both these don't apply file a complaint or court case.
But call verizon first to ask why the shortage. I think financial affairs would be the best to call. (billing)

IMac won't boot after OSX Intel update crash - Newbie needs help please!

Hi,
at the weekend I updated OSX on my IMac 17 with an Intel update. An error message said that the update could not be installed and that the update was sent to the trash - a restart was requested. Since that shutdown my Mac chimes and gets stuck at the white load screen (hard drive is quiet).
I've tried the following:
Holding Shift key upon boot to initiate Safe Mode - No Joy!
Apple+S to run disk utlity/console - cannot initiate to cmd prompt!
Just as a little background - I'm a recent Apple convert and typical Windows defector. I've seen the light after many years in M**soft environments (I even trained to MCSE) but my Mac OS knowledge is considerably lacking. Let's be honest - so far I haven't had any problems.
Any gentle help would be most appreciated folks - I'm not sure where to start and I want my baby back!
Many thanks.

Same here. I have an iMac 20". It has been upgraded to Leopard and running fine since I purchased it 2 weeks ago. I downloaded the latest OS/X update (100+MB in size) but the installation failed. The system requested a reboot but it has not been able to ever since. It simply keeps beeping with a white screen. I put the Leopard DVD in, held the "C" key, but nothing works. Now I have a system that won't work. From now on, I will shy away from getting the latest update .... I am planning to take it to the apple store

1) How to reduce MacBook boot up time? 2) Should I upgrade my 2008 MacBook to Lion? 3) How long will a 2008 MacBook last (after 4 years)? Thanks!

I have three quick questions to ask:
1. My MacBook (bought in late 2008, 2.4 GHz Intel Core 2 Duo, 2GB RAM, 160 GB HD, running Leopard/10.5.8) boots up quite slow. It can take a while to boot up and shut down.
Question: What should I do to reduce the boot up time?
I haven't done a clean up for a while, and am a MacBook newbie (after 4 years, still) for the tools. I think I need to remove some applications but don't know exactly how. Also I am looking for stuff like System Defragment / Compression (tools available for Windows OS) to tune the hard disk performance, if possible.
2. Sort of related to this slow boot-up time - should I bother to upgrade to Snow Leopard (pay $ 29.00) and then upgrade to Lion (another $ 29 ?) for some 250 new features that I am not exactly sure if I will need it (or my 2008 MacBook can handle it well)?
My friend has a 2011 MacPro which he let me use it for a while, so I think I am already using Lion, but frankly I can't tell much difference from the user experience (am just a very average Mac user!).
Question: Should I bother the money and the time (I heard the downloading and installation time for Lion is very long) if all I care is boot-up time?
3. One last question - How long can my MacBook last? Is there a way to find out the battery life? Any indication that my MacBook might be on the edge of its life cycle anytime soon?
I heard that typically the life for a laptop (PC or Mac) is 2 years. I am not a heavy user, and I guess that's why my MacBook is still alive after 4 years. But should I expect that to be failing any time soon?
Thank you!

I'll try to make it short but with your questios, might be impossible.
I own both late 2008 MB Uni with 2Ghz and a brand new late 2011 MBP 13 inch.
I have lion running on both Macbooks with no slow down or issues.
The late 2008 I upgraded to 8GB Crucial DDR3 Memory and 320GB Seagate Hard Drive. Total cost to me? $140 CDN ( i live in Canada ).
My MB Uni's battery has 1047 cycle count and I still get 3-1/2 - 4 hours of battery life depending on what applications I'm using.
As for typical life of a PC or MAC ( I own both ). The PC's life is shorter than a MB. I have a 4 year old Dell Vostro that I had to do a RAM upgrade so Windows 7 would run properly.
My late 08 MB had 4GB of RAM when I upgraded to Lion with no issues. i just decided to go 8GB because it was cheap.
A 2GB MB will boot up and run faster than a 4GB PC with windows 7.
Nothing is obsolete if you can still do your stuff on your MB.
To make it boot up faster, see what's loading on startup and take them off if you don't need them.

MacBook Pro won't boot after 10.6.8 update.

I completely erased my hard drive, reinstalled Snow Leopard and updated to 10.6.7. I then performed an Apple Hardware Test and verified the disk using disk utility. Both tests were successful. I then updated to 10.6.8 using the combo update and restarted my MacBook Pro. The boot process ran fine until the system locked up on the bright blue screen. No peripherals were connected to the laptop during this process. I powered the laptop down using the power button and turned it on again. This time, I entered verbose mode. The last line of text that I see before the screen turns black is "[ PCI configuration begin ]". Can anyone assist me with this issue?
My System Profile is as follows.
Hardware Overview:
Model Name:          MacBook Pro
Model Identifier:          MacBookPro3,1
Processor Name:          Intel Core 2 Duo
Processor Speed:          2.4 GHz
Number Of Processors:          1
Total Number Of Cores:          2
L2 Cache:          4 MB
Memory:          3 GB
Bus Speed:          800 MHz
Boot ROM Version:          MBP31.0070.B07
SMC Version (system):          1.16f11
Serial Number (system):          System Serial#
Hardware UUID:          00000000-0000-1000-8000-001B639863A4
Sudden Motion Sensor:
State:          Enabled

Might be time to replace the PRAM battery. That's not the normally accessible battery, but it is one that often fails after 4 years.

Macbook pro won't boot after installing update 10.9.3

macbook pro won't boot after installing update 10.9.3

Please read this whole message before doing anything.
This procedure is a diagnostic test. It’s unlikely to solve your problem. Don’t be disappointed when you find that nothing has changed after you complete it.
The purpose of the test is to determine whether the problem is caused by third-party software that loads automatically at startup or login, by a peripheral device, by a font conflict, or by corruption of the file system or of certain system caches.
Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards, if applicable. Start up in safe mode.
Note: If FileVault is enabled, or if a firmware password is set, or if the startup volume is a Fusion Drive or a software RAID, you can’t do this. Ask for further instructions.
Safe mode is much slower to start up and run than normal, with limited graphics performance, and some things won’t work at all, including sound output and Wi-Fi on certain models. The next normal startup may also be somewhat slow.
The login screen appears even if you usually login automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
Test while in safe mode. Same problem?
After testing, restart as usual (not in safe mode) and verify that you still have the problem. Post the results of the test.

MacBook Pro won't boot after trying to install 10.7.3 update. Start up stalls at Apple logo and spinning gear.

MacBook Pro won't boot after trying to install 10.7.3 update. Start up stalls at Apple logo and spinning gear. Computer won't even start in safe mode.

My daughter's MacBook Pro was doing exactly the same thing. I don't know if it had anything to do with the latest update. She called me about a week ago saying that her MacBook began running slower by the day . She then called me Friday and told me that it wouldn't get past the gray screen and the gear just kept on spinning. I did everything I could over the phone including Safe mode which it wouldn't go into and thought maybe it was the hard drive. She took it to the Apple store. Originally, they also thought it was the hard drive. It ended up being a corrupted operating system (Lion). Apple genius simply re-installed Lion and she's back up and running. Good thing she backed up right before it crapped out. She'll be restoring everything tonight. Don't know if re-installing Lion will help your situation, but it did the trick for my daughter.

[SOLVED] Arch won't boot after I created a separate /var parition

Arch won't boot after I created a separate /var parition on an existing installation.And let me confess: it was maybe stupid trying to do it on an existing install.
I edited the fstab correctly, copied the files using rsync preserving permissions. Then I kept a backup of /var using tar. Then went on to delete everything under /var, ie /var/*, the /var folder is still there. All this I did from a live CD. After that I booted into my arch linux. Here I get messages about systemd successfully finishing fsck on each of my partitions, then the screen starts blinking. And there is no more output. Pressing Ctrl+Alt+Delete causes systemd to stop its services and reboot.
Having realized I had borked my system, I removed the /var line from fstab and restored /var from the tar file I made earlier. Again I did this from a live cd. Rebooted into my arch system, and again similar issues, namely that after fsck and messages informing a few services had started, the screen keeps blinking.
The live cd I used for reorganizing my partitions was elementary OS freya. They have GParted in there. I also have an arch install iso lying aroung from May 2013. If necessary, I can download the latest version. I am currently typing from a Windows installation I dual boot from.
I don't know how to extract any boot logs as I am locked out of the system. Here is my fstab in any case:
# Filesystem information
# /dev/sda5 LABEL=fs_root
UUID=b9d739cf-fd8c-46dd-a919-bd827dc47c66 / ext4 rw,noatime,data=ordered 0 1
# /dev/sda9 LABEL=fs_var
UUID=ec0f7a49-dccd-43ab-8651-9aa3fdb41cc7 /var ext4 rw,noatime,data=ordered 0 2
# /dev/sda2 LABEL=fs_boot
UUID=0e8ab31a-3bda-4b85-a901-a36f21b1583d /boot ext2 rw,noatime 0 2
# /dev/sda6 LABEL=fs_home
UUID=d9e63c47-274e-447f-ad01-0d97afe0fd34 /home ext4 rw,noatime,data=ordered 0 2
# /dev/sda7 LABEL=fs_swap
UUID=7301227c-e9f3-41b8-9d0f-4cf3c159491c none swap defaults 0 0
# /dev/sda3 LABEL=fs_win
UUID=12B639D1B639B5D7 /fs_win ntfs uid=1000,gid=1000,dmask=027,fmask=137,showexec,nofail,noauto,x-systemd.automount 0 0
# /dev/sda3 LABEL=fs_share
UUID=D272269772268079 /fs_share ntfs uid=1000,gid=1000,dmask=027,fmask=137,showexec,noauto,nofail,x-systemd.automount 0 0
I would greatly appreciate any help.
Last edited by richcocoa (2015-05-03 18:04:44)

Have you moved everything from /var to /new_var (i named it for learning purpose)? You shoud copy content from /var but not on the fly but booting from arch iso cd, and than you shoud mount your / into arch-chroot environement, mount all of your mount points and than copy content from default /var to new /var. The copying should be done with this
cp -rax
and you can add -v switch to verbose output. I have my own /var moved the same way.
The simples way is:
-boot the arch iso cd
-mount all of your mount point (i created here in this step /new_var to move /var to a new place, and this /new_var i put in /etc/fstab as /var later)
-copy /var to /new_var with -rax or -vrax (recursive, archive, this filesystem or verbose, recursive, archive, this filesystem switches)
-umount all of it
-reboot.
Last edited by firekage (2015-05-02 07:49:20)

Mac won't boot after updating to OSX 10.6.4

I am on my 3rd Mac that won't boot after updating to OSX 10.6.4. One MacBook Pro and two iMacs. I fixed one but the last two are getting the better of me. HD is not fried. Have tried every keyboard shortcut on startup, Disk Warrior via. Target Disk, repairing permissions in single user mode. The machines will not boot off of a CD or DVD and it will not boot up in safe mode. Something in the startup files is preventing startup. I am suspecting Sophos antivirus. I tried to uninstall it and trash it but I think it's still blocking something. Any help would be appreciated.

Got it! Not sure if removing Sophos had anything to do with it but here's what I did.
1) boot dead machine in Target Disk Mode (iMac)
2) boot good machine off Snow Leopard disk (MacBook)
3) install OS to dead machine- I found this next part very curious. When the install was complete the MacBook restarted as the iMac.
4) ran software updates
5) shut down MacBook then shut down iMac
6) rebooted iMac- all was good
I actually did this twice because a co-worker had the exact same problem on her MacBook Pro. Got both fixed today.
Thanks everyone for your help!

My MacAir 1st gen. won't boot after latest OS X Lion update.

My MacAir 1st gen. won't boot after latest OS X Lion update. tried safe boot(didn't work) tried disk repair, said it was successful, but my mac won't start up. Just get white screen. Also been having trouble with it overheating. Fan seems to work. But when it get too hot whole interface slows down.

Yikes, I hope you have AppleCare on it still, I think it needs to be taken in, but as a last ditch effort...
Have you done a PRAM reset, CMD+Option+p+r...
http://support.apple.com/kb/HT1379
In fact, do 3 in a row, takes a bit of time.

Mac mini won't boot after RAM upgrade.

Tried installing new RAM in my Mac Mini, 512MB stock to 2GB of Crucial. Followed the directions to a T, grounded myself the whole time.
Things I've tried so far:
1. Resetting the PRAM, no luck.
2. Holding option at start-up, shows no icon.
3. Holding shift, no luck.
4. Holding X, nothing.
How do I get it to accept a CD if it won't boot?

Welcome to Apple Discussions!
You clearly have a problem, but you don't describe exactly what that is other than that your mini won't boot after the upgrade. What happens when it starts up? Does it attempt to start and hang up on the grey or blue screens, or does it start beeping at you almost immediately after you try and start it up, and also flash the power light?
If the former, then you may have dislodged a connector while working inside the system, in which case opening it up and checking that everything is firmly connected would be the first thing to do. If the latter, then the beeping/light flashing is the system telling you it has failed the power-on self test and the pattern of beeps/lights indicates why. In your case likely the system can't find workable memory. In that instance, opening the system and ensuring that the RAM is firmly and fully seated would be a good step, and if the mini continues to fail, then replacing the new RAM with the original to test that the system will then start.
It is not likely that anything had damaged your MacOS install in the process of upgrading, thus normally no reason to need to boot to CD as a result of a RAM issue.

Mac Mini won't boot after update

I have a Mac Mini that won't boot after the most recent software update. Since the Mini has only a bluetooth keyboard and mouse, a number of the usual options (hold down shift, etc.) won't work. I've tried a reset, also no luck. At the moment, I can't locate my Tiger install CD either.
When holding the power button on during boot, I get a series of flashes from the status light on the front (a set of very rapid flashes, followed by a slower set, followed by a slow set) but no startup chime, or fan, or video. My display and power source are both known-good (work fine with my Powerbook)
Any suggestions, other than buying a hardwired keyboard/mouse?

Welcome to Apple Discussions!
The 'newer version of OS X" error occurs because the installer on the DVD you have booted to has by default been set to update the version of MacOS on the hard drive, which of course it can't do because the version of MacOS it is installing is newer. The only way to install in this situation is to select a different option. However, that isn't what you want to do at this point, because as it says, you'll loose your data if you do an 'erase and install'.
Instead, you should see menus at the top of the screen when it's booted to that install disk. Click the Utilities menu, select Disk Utility, and then click the top entry for the internal hard drive on the left. Once done, click on the 'Repair Disk' button (not Repair Permissions). This will test the drive to make sure it's OK. If it reports errors, and then reports 'error or exit' with the drive not repaired, you will either need a 3rd party application such as Alsoft's Disk Warrior, or to perform an erase and install (which of course you don't want to do at this point because your data is not backed up).
If the Repair Disk process completes with no errors, next select Repair Permissions, and let that process complete, then reboot the system as normal to see if you can now access the drive.

LC 475 won' boot after 13 years of good service

Similar Messages

Maybe you are looking for