LDOM dladm does not show other interface.
Create another vnet1 on LDOM (ldg0). But dladm does not show it. There are entries in path-to-inst for it and I was able plumb interface.
bash-3.00# ifconfig -a
lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
vnet0: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2
inet 10.2.100.77 netmask ffffff00 broadcast 10.2.100.255
ether 0:14:4f:fb:32:a
vnet1: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 3
inet 192.168.30.30 netmask ffffff00 broadcast 192.168.30.255
ether 0:14:4f:fb:6c:99
bash-3.00# dladm show-dev
vnet0 link: unknown speed: 0 Mbps duplex: unknown
bash-3.00#
Yet dladm does not show device. What have I done wrong?
Here the ldm binding info for just networking
# ldm list-bindings primary (network only)
VSW
NAME MAC NET-DEV ID DEVICE LINKPROP DEFAULT-VLAN-ID PVID VID MTU MODE
primary-vsw0 00:14:4f:fb:1d:38 e1000g0 0 switch@0 1 1 1500
PEER MAC PVID VID MTU LINKPROP
vnet0@ldg0 00:14:4f:fb:32:0a 1 1500
vnet1@lqwest 00:14:4f:fb:b0:34 1 1500
vnet2@ldg0 00:14:4f:fb:6c:99 1 1500
# ldm list-bindings ldg0 (network only)
NETWORK
NAME SERVICE ID DEVICE MAC MODE PVID VID MTU LINKPROP
vnet0 primary-vsw0@primary 0 network@0 00:14:4f:fb:32:0a 1 1500
PEER MAC MODE PVID VID MTU LINKPROP
primary-vsw0@primary 00:14:4f:fb:1d:38 1 1500
vnet1@lqwest 00:14:4f:fb:b0:34 1 1500
vnet2@ldg0 00:14:4f:fb:6c:99 1 1500
NAME SERVICE ID DEVICE MAC MODE PVID VID MTU LINKPROP
vnet2 primary-vsw0@primary 1 network@1 00:14:4f:fb:6c:99 1 1500
PEER MAC MODE PVID VID MTU LINKPROP
primary-vsw0@primary 00:14:4f:fb:1d:38 1 1500
vnet0@ldg0 00:14:4f:fb:32:0a 1 1500
vnet1@lqwest 00:14:4f:fb:b0:34 1 1500
It appears to be working, but is this correct since dladm does not show the vnet1 interface?
I had the same problem. SUN support recommends latest kernel patches. That solved my problem.
Similar Messages
-
Dladm does not show mac address for aggr
All,
When I run dladm show-aggr for my two aggr interfaces, I have one not displaying its MAC. Anyone a clue how I can get this sorted?
key: 2 (0x0002) policy: L2 address: 0:14:4f:da:13:e8 (auto)
device address speed duplex link state
nxge2 0:14:4f:da:13:e8 1000 Mbps full up attached
nxge3 <unknown> 1000 Mbps full up attachedCheers,
Davy
Edited by: Davy_S on Apr 18, 2009 1:52 AMI had the same problem. SUN support recommends latest kernel patches. That solved my problem.
-
Hi, I'm trying to make my first IPhone app. After having problems with interface builder the first time I coppied the code directly from a tutorial in case I made any mistakes. I saved the program, and re-opened the .xib file. Right clicking File's Owner does not show a list of methods. I've been looking around for solutions for this but have not gotten anything to work. I tried deleting the default .xib and creating a new one through file-> new file. This did not help. I did notice that File's owner was showing up as a light blue cube apposed to a yellow one now and found that a bit odd but otherwise nothing changed. I opened the library menu and selected helloWorldiPhoneViewController so it would show up in the view port. I set the class field of File's Owner to hellowWorldiPhoneViewController. File's Owner still does not show methods when right clicked or when a line is dragged over a button. I read somewhere that the color of nib on the lower left of the viewport may indicate a problem, but it is green not indicating any issue. Every solution I found for someone else seems nto to work for me and I don't know how to continue.
here is the .h file just in case:
// HelloWorldViewController.h
// HelloWorld
// Created by Paul Peelen on 2011-03-14.
// Copyright 2011 9697271014. All rights reserved.
#import <UIKit/UIKit.h>
@interface HelloWorldViewController : UIViewController {
UILabel *textLabel;
@property (nonatomic, retain) IBOutlet UILabel *textLabel;
- (IBAction)changeTheTextOfTheLabel;
@end
I'm trying to connect changeTheTextOfTheLabel to a button and textLabel to a labelYou need a parameter for an interface builder method. The type should be id and the name is typically "sender". It would look like this:
- (IBAction)changeTheTextOfTheLabel: (id) sender;
Be careful about those tutorials. Many are ancient and do not correspond to current Xcode behaviour. -
Mac OS X Server v10.7 does not show the ethernet link aggregated interface i created. Does Lion server support ethernet link aggregated interfaces?
Thanks for responding Cold--
Hardware: Mac Pro 3.0 GHZ quad core xeon
I read the link but it still does not explain why the aggregated dual ethernet interface does not show up in the Network tab of the hardware section Lion Server. I was able to see it on the network and looks to be using a single static IP that I assigned. My concern was that is this supported and will it allow for failover and double performance of the single network interface.
Any thoughts?
Thanks again! -
Hello I send imessages to a phone number I receive delivery notice but sms does not show on receiving phone. Otherwise when receive imessage from other phone I reply and receiver sees SMS !!! Any explanation ?
To my knowledge, I've only seen this for imessage only and not SMS.
The other users would need to have send read receipts enabled on their phone. -
My Macbook Air with Lion does not show up on my network to any of my other computers (PC's) , even though it is connected to my wifi and does access the Internet. In addition, my other computers sometimes show up in Finder and sometimes they're not there. Sometimes they do show in Finder and when I click on them, I get "Connection Failed", other times, they connect. Also some shared folders on those other computers, which are PC's are not accessible, even though fully shared. My network is Apple Airport Extreme and works perfectly otherwise, including all PC's being able to see each other. Help would be much appreciated
I got the same problem. I want to access my shared folder on my home windows7 from my MBA. Tried many suggestions on the web but all to no avail. I thought that should be very trivial. Maybe a Lion bug?
-
I have a new movie rental in my iTunes account on my Mac Book Pro but does not show up on Apple TV. All my other purchased movies are in there OK. Any suggestions?
It won't show up on your Apple TV until it is fully downloaded into iTunes on your computer, have you done this.
-
I understand that Spellchecker is pre-installed but I cannot verify this is the case with v.4.0 Firefox. I have right-clicked on webpages and it does not say Dictionary is missing, so I assume the problem remains with Spellchecker. I expected to find Spellchecker and Languages under Edit in nav bar but it does not show up, What must I do? Richard
That should work on a Mac as well.
You did download and install the French version?
Download a new copy of the Firefox program and save the DMG file to the desktop
* Firefox 4.0.x: http://www.mozilla.com/en-US/firefox/all.html
* Trash the current Firefox application to do a clean (re-)install
* Install the new version that you have downloaded
Your profile data is stored elsewhere in the [http://kb.mozillazine.org/Profile_folder_-_Firefox Firefox Profile Folder], so you won't lose your bookmarks and other personal data. -
I currently have 2 Iphone 4 s. Both are unlocked vervion from Apple. In the messaging app the camera icon shows but it does not show on the other. How can I get it to chow on both devices? Thanks in advance for your help.
Chet [email protected]So after looking a bit closer i have noticed that when i have the phone plugged into the computer it shows the songs but when i dont have it plugged in and i go so the song icon on the bottom of the music menu screen it says i have no songs!
-
when i drag the pdf file over other (in previewer) to merge it does not show green circle with plus one. what to do?
Hello djensen1x,
Could you please let me know what version of Acrobat are you using.
Also, tell me your workflow of combining those PDF files?
Please share the screenshot of the error message that you get.
Hope to get your response.
Regards,
Anubha -
My webpage does not show on Firefox, but it does on other browsers
I have a personal website, http://www.kryshu.com that I have created myself on Dreamweaver. I have 7 pages and all except one appear on Firefox. Everything was fine until a couple of months ago when I updated some of the pages, again on Dreamweaver. All of a sudden my 'Portfolio - images' page does not show anything. It is empty - blank. It had text and images. I reloaded several times but each time the 'Portfolio - images' page is blank.
This happened only on Firefox. On Internet Explorer and Chrome the page works fine.
So, I presume the problem is with Firefox. What should I do?The content is on the page, but is shifted down considerably.
Looks that this is caused by a simple typo: height="790%" instead of height="790" for one of the tables that causes all content to get shifted down.
<pre><nowiki><table width="672" height="790%" border="0" cellpadding="0" cellspacing="0"></nowiki></pre> -
titles are not visible, they show up on timeline as a grey box no text does not effect other events or projects. could this have something to do with motion
Without seeing the timeline it sounds as if they've been off. Maybe you pressed the V or the role is switched off in the timeline index.
-
in iPhoto 09 Info does not show tags on aperture, time, iso etc. Other tags like place, pixels are shown. There is no little arrow on this info menu to go to full info box. How come ?
It does. Photos Menu -> Show Extended Photo Information.
Then note the disclosure arrows as indictaed in this thread:
https://discussions.apple.com/message/16512794#16512794
Regards
TD -
I have a first Genreation iPAD and just a new Apple TV, 3rd Generation. The Apple TV does not show the Internet menu option after booting up.
There isn't one.
AppleTV3 has icons for all the internet features. -
HT2801 MacBookPro does not show titles of cd^s burned on other computer
Hello anyone out there who can help. I insert a cd with music into my MacBookPro and it does accept it and it is running, but it does not show any titles. I know that the disc is full, because I have checked it on a PC. can somebody help?
Hi,
Please take a try to disable SMB2 on this client machine.
sc config lanmanworkstation depend= bowser/mrxsmb10/nsi
sc config mrxsmb20 start= disabled
More information, please take a look at the following KB article:
How to enable and disable SMBv1, SMBv2, and SMBv3 in Windows Vista, Windows Server 2008, Windows 7, Windows Server 2008 R2, Windows 8, and Windows Server 2012
Best regards
Michael Shao
TechNet Community Support
Maybe you are looking for
-
Ipod will not turn on and is not recognized by windows to restore it
I have a 30g video ipod that worked fine for about a week. Today i tried to turn it on and i got the sad face with the website for apple support. I tried the 5 R's but nothing worked. I can't get the ipod to go into disk mode and i can't restore it b
-
Why do links in the template change location to 'file:///'...on the pages created from the template?
Im not sure what I am doing wrong but I am building a portfolio site from a template that I downloaded online. The site is working and I am slowly converting it from the template content to the content that I want. As I will be editing the site and a
-
IPod has stopped showing videos
I downloaded a new TV show to my iTunes account and plugged in my iPod to transfer the file. Unfortunately, my daughter shut off the computer before the transfer was complete (the "Do Not Disconnect" icon was still flashing). Now when I try to view a
-
hi I'm having a query running for long time, Im new to dba can any one suggest me methods to make it faster it's running now and i have to make it execute it faster parallel servers=4, and there are no inactive sessions. thanks in advance
-
Keyboard shortcut to merge cells in a table?
Does anyone know if there's a keyboard shortcut to merge cells in a table in Pages? That would save me a tremendous amount of time. I've looked in the documentation, and there wasn't one listed.