Limit QoS

hi!
how limit speed - for windows update?
WSA hardware.
i find: Set action for 5 applications of type: Software Updates
but not avialable - speed limit, use global setting...
Software Updates Set default action for application type: Software Updates
(in section: Edit Overall Bandwidth Limit - not work, )...
client use full Bandwidth

Unfortunately, WSA unable to perform bandwidth limit for software updates since WSA is a proxy device and not a QoS device.
At the moment the only bandwidth limit functionality available in WSA is only limiting Media category or application and also Facebook application (if AVC engine is enable)
Hope this helps

Similar Messages

3750X rate-limit (QoS)

Hello,
I'm trying to configure a rate-limit in a 3750X but I'm not seeing any result...
These are my configurations:
RF#show run
Building configuration...
Current configuration : 23410 bytes
! Last configuration change at 08:53:35 UTC Sun Mar 14 1993
version 15.0
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname RF
boot-start-marker
boot-end-marker
no aaa new-model
switch 1 provision ws-c3750x-48p
system mtu routing 1500
ip routing
ip domain-name erf.carco.com.mx
rep admin vlan 100
mls qos
spanning-tree mode pvst
spanning-tree extend system-id
vlan internal allocation policy ascending
vlan 2
vlan 4
vlan 6
vlan 8
vlan 10
vlan 20
vlan 21
vlan 22
vlan 23
vlan 25
vlan 26
vlan 30
vlan 50
vlan 53
vlan 70
vlan 81
vlan 91
vlan 92
vlan 93
vlan 95
vlan 96
vlan 99
vlan 100
vlan 102
vlan 110
vlan 122
vlan 129
vlan 200
vlan 213
vlan 227
vlan 333
vlan 357
vlan 417
vlan 444
vlan 500
vlan 502
vlan 555
vlan 700
vlan 712
vlan 910
vlan 911
vlan 951
vlan 1105
vlan 1508
vlan 1830
vlan 1870
vlan 1890
vlan 1891
vlan 1892
class-map match-any test
match access-group 100
policy-map test
class test
police 150000000 512000 exceed-action drop
interface Loopback0
ip address 10.20.40.106 255.255.255.0
interface Port-channel22
switchport trunk encapsulation dot1q
switchport trunk native vlan 100
switchport mode trunk
bandwidth 10000000
rep segment 10
interface Port-channel24
switchport trunk encapsulation dot1q
switchport trunk native vlan 100
switchport mode trunk
bandwidth 10000000
rep segment 10
interface FastEthernet0
no ip address
no ip route-cache
shutdown
interface GigabitEthernet1/0/1
interface GigabitEthernet1/0/2
interface GigabitEthernet1/0/3
switchport trunk encapsulation dot1q
switchport trunk native vlan 100
switchport trunk allowed vlan 2,10,50,53,60,70,91-93,95,96,99,100,110,213,227
switchport trunk allowed vlan add 500,700,910,911,951,1830,1870,1890-1892
switchport mode trunk
no logging event link-status
shutdown
speed 1000
duplex full
interface GigabitEthernet1/0/4
switchport trunk encapsulation dot1q
switchport trunk native vlan 100
switchport trunk allowed vlan 2,8,10,20,50,53,70,91-93,95,96,99,100,110,213
switchport trunk allowed vlan add 227,500,700,910,911,951,1830,1870,1890-1892
switchport mode trunk
shutdown
speed 1000
duplex full
interface GigabitEthernet1/0/5
interface GigabitEthernet1/0/6
interface GigabitEthernet1/0/7
interface GigabitEthernet1/0/8
interface GigabitEthernet1/0/9
interface GigabitEthernet1/0/10
switchport access vlan 91
switchport mode access
logging event link-status
interface GigabitEthernet1/0/11
interface GigabitEthernet1/0/12
interface GigabitEthernet1/0/13
interface GigabitEthernet1/0/14
interface GigabitEthernet1/0/15
switchport access vlan 91
switchport mode access
logging event link-status
interface GigabitEthernet1/0/16
interface GigabitEthernet1/0/17
interface GigabitEthernet1/0/18
interface GigabitEthernet1/0/19
interface GigabitEthernet1/0/20
switchport access vlan 91
switchport mode access
logging event link-status
interface GigabitEthernet1/0/21
interface GigabitEthernet1/0/22
interface GigabitEthernet1/0/23
interface GigabitEthernet1/0/24
interface GigabitEthernet1/0/25
switchport access vlan 910
switchport mode access
interface GigabitEthernet1/0/26
interface GigabitEthernet1/0/27
interface GigabitEthernet1/0/28
interface GigabitEthernet1/0/29
interface GigabitEthernet1/0/30
interface GigabitEthernet1/0/31
interface GigabitEthernet1/0/32
interface GigabitEthernet1/0/33
interface GigabitEthernet1/0/34
interface GigabitEthernet1/0/35
interface GigabitEthernet1/0/36
interface GigabitEthernet1/0/37
no switchport
bandwidth 150000
ip address 10.20.103.13 255.255.255.252
rate-limit output access-group 100 24000000 3000000 3000000 conform-action transmit exceed-action drop
logging event link-status
interface GigabitEthernet1/0/38
interface GigabitEthernet1/0/39
interface GigabitEthernet1/0/40
interface GigabitEthernet1/0/41
interface GigabitEthernet1/0/42
interface GigabitEthernet1/0/43
switchport trunk encapsulation dot1q
switchport trunk native vlan 100
switchport mode trunk
bandwidth 10000000
channel-group 24 mode on
interface GigabitEthernet1/0/44
interface GigabitEthernet1/0/45
switchport trunk encapsulation dot1q
switchport trunk native vlan 100
switchport trunk allowed vlan 2,10,50,53,60,70,91-93,95,96,99,100,110,213,227
switchport trunk allowed vlan add 500,700,910,911,951,1830,1870,1890-1892
switchport mode trunk
shutdown
interface GigabitEthernet1/0/46
switchport trunk encapsulation dot1q
switchport trunk native vlan 100
switchport trunk allowed vlan 2,10,50,53,60,70,91-93,95,96,99,100,110,213,227
switchport trunk allowed vlan add 500,700,910,911,951,1830,1870,1890-1892
switchport mode trunk
shutdown
interface GigabitEthernet1/0/47
switchport trunk encapsulation dot1q
switchport trunk native vlan 100
switchport mode trunk
bandwidth 10000000
channel-group 22 mode on
interface GigabitEthernet1/0/48
switchport trunk encapsulation dot1q
switchport trunk native vlan 6
switchport trunk allowed vlan 2,7,10,20,50,53,70,91-93,95,96,99,100,110,213
switchport trunk allowed vlan add 227,700,910,911,951,1830,1870,1890-1892
switchport mode trunk
logging event link-status
shutdown
interface GigabitEthernet1/1/1
switchport trunk encapsulation dot1q
switchport trunk native vlan 100
switchport trunk allowed vlan 2,8,10,20,50,53,60,70,91-93,95,96,99,110,213,227
switchport trunk allowed vlan add 500,700,910,911,951,1830,1870,1890-1892
switchport mode trunk
shutdown
interface GigabitEthernet1/1/2
switchport trunk encapsulation dot1q
switchport trunk native vlan 100
switchport trunk allowed vlan 2,8,10,20,50,53,60,70,91-93,95,96,99,110,213,227
switchport trunk allowed vlan add 500,700,910,911,951,1830,1870,1890-1892
switchport mode trunk
shutdown
interface GigabitEthernet1/1/3
switchport trunk encapsulation dot1q
switchport trunk native vlan 6
switchport trunk allowed vlan 2,6,8,10,20,50,53,70,91-93,95,96,99,100,110,213
switchport trunk allowed vlan add 227,700,910,911,951,1830,1870,1890-1892
logging event link-status
shutdown
interface GigabitEthernet1/1/4
switchport trunk encapsulation dot1q
switchport trunk native vlan 6
switchport trunk allowed vlan 2,6,8,10,20,50,53,70,91-93,95,96,99,100,110,213
switchport trunk allowed vlan add 227,700,910,911,951,1830,1870,1890-1892
switchport mode trunk
logging event link-status
shutdown
interface TenGigabitEthernet1/1/1
interface TenGigabitEthernet1/1/2
interface Vlan1
no ip address
shutdown
interface Vlan6
description ***LANERF**
ip address 10.20.6.106 255.255.255.0
no ip redirects
interface Vlan23
description < TRANSITO MUR >
no ip address
no ip redirects
interface Vlan100
description < VLAN MAN >
ip address 10.20.100.106 255.255.255.0
no ip redirects
ip ospf authentication message-digest
ip ospf message-digest-key 1 md5 7 032368342B2F0F
ip ospf dead-interval minimal hello-multiplier 4
router ospf 1
router-id 10.20.40.106
auto-cost reference-bandwidth 100000
area 0.0.0.0 authentication message-digest
area 1.80.1.1 authentication message-digest
redistribute connected subnets
redistribute static subnets
passive-interface default
no passive-interface Vlan23
no passive-interface Vlan100
no passive-interface GigabitEthernet1/0/37
network 10.20.6.0 0.0.0.0 area 0.0.0.0
network 10.20.40.106 0.0.0.0 area 0.0.0.0
network 10.20.91.6 0.0.0.0 area 0.0.0.0
network 10.20.100.106 0.0.0.0 area 0.0.0.0
default-information originate
ip http server
ip http secure-server
access-list 100 permit ip 10.50.80.0 0.0.0.255 10.80.80.0 0.0.0.255
access-list 100 permit ip 10.80.80.0 0.0.0.255 10.50.80.0 0.0.0.255
snmp-server community ASComRO RO
line con 0
line vty 0 4
login
line vty 5 15
login
event manager applet track_qos_down authorization bypass
event syslog pattern "TRACKING-5-STATE: 15 ip sla 15 reachability Up->Down"
action 1 cli command "enable"
action 2 cli command "configure terminal"
action 3 cli command "interface giga1/0/37"
action 4 cli command "rate-limit output access-group 100 400000000 50000000 50000000 conform-action transmit exceed-action drop"
action 5 cli command "end"
event manager applet track_qos_up authorization bypass
event syslog pattern "TRACKING-5-STATE: 15 ip sla 15 reachability Down->Up"
action 1 cli command "enable"
action 2 cli command "configure terminal"
action 3 cli command "interface giga1/0/37"
action 4 cli command "no rate-limit output access-group 100 400000000 50000000 50000000 conform-action transmit exceed-action drop"
action 5 cli command "end"
end
ERF#
ERF#show mls qos
QoS is enabled
QoS ip packet dscp rewrite is enabled
ERF#show mls qos inter gigabitEthernet 1/0/37
GigabitEthernet1/0/37
trust state: not trusted
trust mode: not trusted
trust enabled flag: ena
COS override: dis
default COS: 0
DSCP Mutation Map: Default DSCP Mutation Map
Trust device: none
qos mode: port-based
When I apply the command I'm seeing a gauge using a 3rd party but I'm not seeing that the traffic will be truncated @ 50Mbps.
Any thoughts???

Hi
Bandwidth commands allocates the particular amount of bandwidth you mention or configure over there.
Basically you have the liberty to configure upto 75% of the available interface bandwidth to different classes.
most widelys used with CBWFQ technique..
so while configuring up the same better to watch out for the exact bandwidth value keyed in on the interface to have your alloocation work properly.
policing basically used for limiting the traffic or to control the bursts by dropping them or marking them with different ip precedence or DSCP values.
its very much similar to the rate-limit command applied on the interface level which again uses token bucket system either single or dual based on the configuration parameters.
for more info on above mentioned clis do check these links..
http://www.cisco.com/en/US/tech/tk543/tk545/tsd_technology_support_protocol_home.html
http://www.cisco.com/en/US/tech/tk543/tk544/tsd_technology_support_protocol_home.html
regds

How to set up a QOS on 3750 switch to limit outbound bandwidth on a server ?

Hi,
I have three LAN ports on a VM server. I want to limit a VM guest (guest server) outbound bandwidth to 3750 swith .
How do I do it ? I want to apply QoS on the switch.
thanks

Disclaimer
The Author of this posting offers the information contained within this posting without consideration and with the reader's understanding that there's no implied or expressed suitability or fitness for any purpose. Information provided is for informational purposes only and should not be construed as rendering professional advice of any kind. Usage of this posting's information is solely at reader's own risk.
Liability Disclaimer
In no event shall Author be liable for any damages whatsoever (including, without limitation, damages for loss of use, data or profit) arising out of the use or inability to use the posting's information even if Author has been advised of the possibility of such damage.
Posting
If you're looking to limit bandwidth FROM your server, you can use an ingress policy on the server's interface and police selectively. For example, if your specific VM has its own IP address, you could police inbound (from the server) traffic matching that IP.

ASR9000/XR - QoS - Limit overall amount of bandwidth per IP

We have a few thousand broadband customers in our network with various speed packages. The highest speed package of 500Mbps.
I'm trying to create an ingress QoS policy that I can apply on my interface facing my upstream providers that will limit put a bandwidth cap PER IP ADDRESS of 500Mbps.
I don't want to limit the overall interface to 500Mbps.
Goal of this is to protect my links deeper in my network from getting over run in the event of a DDoS attack.
Now I know this is not going to protect or mitigate any DDoS attack (like the vDDoS solution with the VSM and Arbor Networks), as budgets are not allowing me to go down that road at this time.
Any ideas on how a QoS policy would look like?
I can limit the overall interface, but struggling with how to limit an interface on a PER IP basis because i want to utilize as much of the 10GE port as possible (under normal conditions).
Simple diagram below.
Look forward to any ideas on this!
-ae
+----------------+
| INTERNET |
| PROVIDER |
+-------+--------+
|
|
+---------------+10 GE
|
+-------+--------+
| BGP EDGE |
| ASR 9000 |
+---+---+---+----+
| | |
| | |
| | |
| | |
+---+---+---+----+
| BROADBAND |
| CUSTOMERS |
+----------------+

I think "Flow aware QoS" is the feature you are looking for:
http://www.cisco.com/c/en/us/td/docs/routers/asr9000/software/asr9k_r5-1/qos/configuration/guide/b_qos_cg51xasr/b_qos_cg51xasr_chapter_01010.html
Florian

Bandwidth Management(Rate Limit) Using QoS Policies

Hello,
I need some advice. We have an ASA 5525 running version 8.6(1)2 and a 10 MG pipe. I have execs that want to limit bandwidth on users for stuff like youtube, stream media, and downloads. I found the article on ‘Bandwidth Management(Rate Limit) Using QoS Policies’ so it appears our firewall can do what we want. I’m not a cisco person. My knowledge is limited when it comes to configuration – that’s why we have SmartNet :). The advice I need is what to ask for, so to speak, when I put a case in. Can bandwidth be limited on end users and/or can they limit the ‘bandwidth rate limit’ to just youtube, steaming media, and downloads? If so, what should the limit be? and I’m assume this would be for ‘incoming’ traffic only? we’re running into some bandwidth hogs – usually youtube and/or streaming media. We have a Barracuda web filter which we’ve used to block and monitor activity but I simply do not have time to babysit this all day. I should also mention we do have critical data running up and down the pipe; such as credit card processing, DB replication between in house DB and hosted website, TPCx and EDI, FTP, and such that we don’t want restricted.
Need input please,
Thanks,
D

Hello,
That's a question that you as the network admin of that organization could answer.
How much traffic for business purposes must travel via HTTP/HTTPS?
How much bandwith are you willing to provide to this 2 protocols?
Those are the kind of answers you need to answer before setting the number
Regards
Remember to rate all of the helpful posts, Just click the 5 stars at the left of each post
Julio

QoS bandwidth rate limit don't work

Hello
Buy a router RV120W, and one of the reasons is limit of bandwidth (QoS). I set up a profile of 1-256 kbps limit, and apply it to the only VLAN that is configured, but does not work and can navigate using the full bandwidth of the internet connection. My firmware version is 1.0.2.6
Screenshots attached
thanks
screenshots attached

Struggling with a similar issue:
the setup: internet adsl <--1mbs--> combined router/modem <--100mbs--> RV 120W
Internet speed is 1mbs. I want to priotize voip calls (via port) and deprioritize one machine (doing downloads). rest of the network should have something in between.
Firmware upgraded to 1.0.3.10
I created the profiles bindings, then in QoS settings, selected Priority, Wan total bandwidth 1mbs, and distributed my profiles onto low/med/high (10/31/61).
When what should be low is downloading, it gets the whole 1mbs and the other are dead slow.
Changed to rate limit, changed the parameters, etc... no more luck.
Can you please shed some light as how to configure this - in my case, the whole bw of wan is being used, and prioriization is not happening,
Rgds

Limit traffic with qos on 3750g

hi,pls help me !
my 3750g:
Cisco IOS Software, C3750 Software (C3750-IPSERVICESK9-M), Version 12.2(55)SE4
cisco WS-C3750G-24TS (PowerPC405) processor (revision M0) with 131072K bytes of memory.
the configuration:
access-list 199 permit ip any any
class-map match-all wqz-up
  match access-group 199
policy-map wqz-up
class wqz-up
  police 90000000 1000000 exceed-action drop
  trust dscp
interface GigabitEthernet1/0/2
switchport access vlan 2302
switchport mode access
service-policy input wqz-up
the question is : it dosen't work
sh policy-map int g1/0/2
GigabitEthernet1/0/2
  Service-policy input: wqz-up
Class-map: wqz-up (match-all)
   0 packets, 0 bytes
   30 second offered rate 0 bps, drop rate 0 bps
   Match: access-group 199
Class-map: class-default (match-any)
   0 packets, 0 bytes
   30 second offered rate 0 bps, drop rate 0 bps
   Match: any
      0 packets, 0 bytes
      30 second rate 0 bps

Hi there
have you enabled QOS on the switch using <config>#mls qos
HTH
Hitesh

Qos- I want to apply limit on FTP traffic

I want to apply Qos on ftp traffic on cisco 6500. Ftp traffic should use only 512 kbps bandwidth. Please any one suggest how should i establish this and any study document will be welcome.
Thanks in advance

Disclaimer
The Author of this posting offers the information contained within this posting without consideration and with the reader's understanding that there's no implied or expressed suitability or fitness for any purpose. Information provided is for informational purposes only and should not be construed as rendering professional advice of any kind. Usage of this posting's information is solely at reader's own risk.
Liability Disclaimer
In no event shall Author be liable for any damages whatsoever (including, without limitation, damages for loss of use, data or profit) arising out of the use or inability to use the posting's information even if Author has been advised of the possibility of such damage.
Posting
How would depend very much on the QoS features of the device. Even 6500 QoS features depend on line cards.
Most, but not all, Cisco switches support 4 egress queue which you can provide different bandwidth allocations. Such allocations usually provide a minimum, but more bandwidth might be used if its otherwise not being used.
For example, you might define four queues that one is a priority queue for real-time traffic; one is a foreground queue with a large bandwidth allocation (not that such traffic should be bandwidth intensive, but to insure high priority for dequeuing; one is a background queue with minimum bandwidth allocation (often where you might want to direct FTP); and the last is a middle allocation for everything else, i.e. your default.
Also on switches, traffic is often placed into a particular egress queue based on L2 CoS or L3 ToS. So, what this means, you'll want to mark your FTP traffic differently than your other traffic, perhaps with CoS 1 or DSCP CS1 or AF1x.
Cisco has some great guides on how to configure QoS for their different platforms although their 11 class model is often overly complex.

SGE2000 QoS: Ingress Rate Limit BUG ?

I buyed a new unit of SGE2000. Thirst I changed firmware to newest one (3.0.0.18) so I do not know what firmware was installed before.
The problem is that it is not posssible to change Ingress Rate Limit to value lower than 3500...
Hardware Version
00.00.01
Software Version
3.0.0.18
Boot Version
2.0.0.03
Manual says:
Ingress Rate Limit — Defines the amount of bandwidth assigned to the interface.
For FE ports, the rate is 62 - 100,000 Kbps.
For GE ports, the rate is 62 - 1,000,000 Kbps
====
Default value for Ingress Rate Limit field is 3500, while I change it to eg. 512 the combobox is opening with warning information:
"Entered value in highlighted field must be an Integer. Range 3500...1000000"
"Committed Information Rate (CIR)" field allow to put a value down to 64, so it is ok.
Should I downgrade firmware to v3.0.0.17 ?
Any help appreciated.

My appologies for the lack of reply here. I checked with the PM for the product and they asked me if there is a case open with the Small Business Support Center (SBSC) on this issue. Have you had a case open on this yet? If not can I ask you to log a case and then respond back to this postig with the case number please? It seems this is a bug so the product team will need to process the fix for this via the standard problem identification/case reporting process.
Thanks in advance!

DMVPN Per Spoke QOS ServicePolicy Limit

I want to impliment per spoke QOS using isakmp profiles and service policy.
My problem is that I have more than 64 tunnels and I understand that service policy configurations are limited to one level of nesting and only 64 classifications.
Does anyone have experience of per spoke QOS greater than 64 flows?

Only if you show me yours for > 64 flows
LOL

Is there any rate-limit or qos hardset in the OfficeExtend AP600?

Only getting 9-10MB of throughput on the Cisco OfficeExtend AP600's. I have a 25mb pipe, and when I use another router, and even a Linksys I'm able to get 25MB downloads. Let me also clarify that I'm using the personal / local SSID of the OfficeExtend, and not the corporate SSID.
Is there a way to change or remove any rate-limiting that has been hard coded into these OfficeExtend AP600 routers?

I remember seeing 2.x limitations on guest VM sizes in the 2.x docs but do not specifically remember reading about limits for a given 2.x VM host nor sets of hosts...
That being said I have 2 in Production & 3 in Testing & really hope to go to Prod soon with version 3 as it seems much better overall. I did not like 3.0.x versions but I like 3.2.1 (haven't tried the newly released 3.2.2 yet).

How Can I limit the bandwith of my internet connection on linux?

Hello, I have 2 Pc's, one for my brother, and the other for me. And well, always we have problems about downloads and lags when we are playing.
For example, when I download packages from pacman, it is done at maximum speed "eating" all connection, and my brother has lag.
Is there anyway to limit the bandwith that use my programs to half, for example? If maximum download speed is 100KB/s, pacman only can download 50 KB/s maximum.
Greetings

Depending on your router you may be able to set Ingress Rate Limit under QoS. Also have a look into trickle: http://aur.archlinux.org/packages.php?d … s=0&SeB=nd
http://monkey.org/~marius/pages/?page=trickle
Last edited by somairotevoli (2007-07-21 01:42:55)

QoS / Native VLAN Issue - Please HELP! :)

I've purchased 10 Cisco Aironet 2600 AP’s (AIR-SAP2602I-E-K9 standalone rather than controller based).
I’ve configured the WAP’s (or the first WAP I’m going to configure and then pull the configuration from and push to the others) with 2 SSID’s. One providing access to our DATA VLAN (1000 – which I’ve set as native on the WAP) and one providing access to guest VLAN (1234). I’ve configured the connecting DELL switchport as a trunk and set the native VLAN to 1000 (DATA) and allowed trunk traffic for VLAN’s 1000 and 1234. Everything works fine, when connecting to the DATA SSID you get a DATA IP and when you connect to the GUEST SSID you lease a GUEST IP.
The problem starts when I create a QoS policy on the WAP (for Lync traffic DSCP 40 / CS5) and try to attach it to my VLAN’s. It won’t let me attach the policy to VLAN 1000 as it’s the native VLAN. If I change VLAN 1000 on the WAP to NOT be the native VLAN I can attach the policies however wireless clients can no longer attach to either SSID properly as they fail to lease an IP address and instead get a 169.x.x.x address.
I'm sure I'm missing something basic here so please forgive my ignorance.
This is driving me insane!
Thanks to anyone that provides assistance. Running config below and example of the error...
User Access Verification
Username: admin
Password:
LATHQWAP01#show run
Building configuration...
Current configuration : 3621 bytes
! Last configuration change at 02:37:59 UTC Mon Mar 1 1993 by admin
version 15.2
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname LATHQWAP01
logging rate-limit console 9
aaa new-model
aaa authentication login default local
aaa authorization exec default local
aaa session-id common
no ip routing
dot11 syslog
dot11 vlan-name Data vlan 1000
dot11 vlan-name Guest vlan 1234
dot11 ssid LatitudeCorp
   vlan 1000
   authentication open
   authentication key-management wpa version 2
   wpa-psk ascii
dot11 ssid LatitudeGuest
   vlan 1234
   authentication open
   authentication key-management wpa version 2
   guest-mode
   wpa-psk ascii
crypto pki token default removal timeout 0
username admin privilege 15 password!
class-map match-all _class_Lync0
match ip dscp cs5
policy-map Lync
class _class_Lync0
set cos 6
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption vlan 1234 mode ciphers aes-ccm
encryption vlan 1000 mode ciphers aes-ccm
ssid LatitudeCorp
ssid LatitudeGuest
antenna gain 0
stbc
station-role root
interface Dot11Radio0.1000
encapsulation dot1Q 1000 native
no ip route-cache
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
interface Dot11Radio0.1234
encapsulation dot1Q 1234
no ip route-cache
bridge-group 255
bridge-group 255 subscriber-loop-control
bridge-group 255 spanning-disabled
bridge-group 255 block-unknown-source
no bridge-group 255 source-learning
no bridge-group 255 unicast-flooding
service-policy input Lync
service-policy output Lync
interface Dot11Radio1
no ip address
no ip route-cache
encryption vlan 1234 mode ciphers aes-ccm
encryption vlan 1000 mode ciphers aes-ccm
ssid LatitudeCorp
ssid LatitudeGuest
antenna gain 0
no dfs band block
stbc
channel dfs
station-role root
interface Dot11Radio1.1000
encapsulation dot1Q 1000 native
no ip route-cache
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
interface Dot11Radio1.1234
encapsulation dot1Q 1234
no ip route-cache
bridge-group 255
bridge-group 255 subscriber-loop-control
bridge-group 255 spanning-disabled
bridge-group 255 block-unknown-source
no bridge-group 255 source-learning
no bridge-group 255 unicast-flooding
service-policy input Lync
service-policy output Lync
interface GigabitEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
interface GigabitEthernet0.1000
encapsulation dot1Q 1000 native
no ip route-cache
bridge-group 1
bridge-group 1 spanning-disabled
no bridge-group 1 source-learning
interface GigabitEthernet0.1234
encapsulation dot1Q 1234
no ip route-cache
bridge-group 255
bridge-group 255 spanning-disabled
no bridge-group 255 source-learning
service-policy input Lync
service-policy output Lync
interface BVI1
ip address 10.10.1.190 255.255.254.0
no ip route-cache
ip default-gateway 10.10.1.202
ip http server
ip http authentication aaa
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
bridge 1 route ip
line con 0
line vty 0 4
transport input all
end
LATHQWAP01#conf
Configuring from terminal, memory, or network [terminal]? t
Enter configuration commands, one per line. End with CNTL/Z.
LATHQWAP01(config)#int dot11radio1.1000
LATHQWAP01(config-subif)#ser
LATHQWAP01(config-subif)#service-policy in
LATHQWAP01(config-subif)#service-policy input Lync
set cos is not supported on native vlan interface
LATHQWAP01(config-subif)#

Hey Scott,
Thank you (again) for your assistance.
So I' ve done as instructed and reconfigured the WAP. I've added an additional VLAN (1200 our VOIP VLAN) and made this the native VLAN - so 1000 and 1234 are now tagged. I've configure the BVI interface with a VOIP IP address for management and can connect quite happily. I've configured the connecting Dell switchport as a trunk and to allow trunk vlans 1000 (my DATA SSID), 1200(native) and 1234 (MY GUEST SSID). I'm now back to the issue where when a wireless client attempts to connect to either of my SSID's (Guest or DATA) they are not getting a IP address / cannot connect.
Any ideas guys? Forgive my ignorance - this is a learning curve and one i'm enjoying.
LATHQWAP01#show run
Building configuration...
Current configuration : 4426 bytes
! Last configuration change at 20:33:19 UTC Mon Mar 1 1993 by Cisco
version 15.3
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname LATHQWAP01
logging rate-limit console 9
enable secret 5
no aaa new-model
no ip source-route
no ip cef
dot11 syslog
dot11 vlan-name DATA vlan 1000
dot11 vlan-name GUEST vlan 1234
dot11 vlan-name VOICE vlan 1200
dot11 ssid LatitudeCorp
   vlan 1000
   authentication open
   authentication key-management wpa version 2
   mobility network-id 1000
   wpa-psk ascii
dot11 ssid LatitudeGuest
   vlan 1234
   authentication open
   authentication key-management wpa version 2
   mbssid guest-mode
   mobility network-id 1234
   wpa-psk ascii
   no ids mfp client
dot11 phone
username CISCO password
class-map match-all _class_Lync0
match ip dscp cs5
policy-map Lync
class _class_Lync0
set cos 6
bridge irb
interface Dot11Radio0
no ip address
encryption vlan 1000 mode ciphers aes-ccm
encryption vlan 1234 mode ciphers aes-ccm
ssid LatitudeCorp
ssid LatitudeGuest
antenna gain 0
stbc
mbssid
station-role root
interface Dot11Radio0.1000
encapsulation dot1Q 1000
bridge-group 255
bridge-group 255 subscriber-loop-control
bridge-group 255 spanning-disabled
bridge-group 255 block-unknown-source
no bridge-group 255 source-learning
no bridge-group 255 unicast-flooding
service-policy input Lync
service-policy output Lync
interface Dot11Radio0.1200
encapsulation dot1Q 1200 native
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
interface Dot11Radio0.1234
encapsulation dot1Q 1234
bridge-group 254
bridge-group 254 subscriber-loop-control
bridge-group 254 spanning-disabled
bridge-group 254 block-unknown-source
no bridge-group 254 source-learning
no bridge-group 254 unicast-flooding
service-policy input Lync
service-policy output Lync
interface Dot11Radio1
no ip address
encryption vlan 1000 mode ciphers aes-ccm
encryption vlan 1234 mode ciphers aes-ccm
ssid LatitudeCorp
ssid LatitudeGuest
antenna gain 0
peakdetect
no dfs band block
stbc
mbssid
channel dfs
station-role root
interface Dot11Radio1.1000
encapsulation dot1Q 1000
bridge-group 255
bridge-group 255 subscriber-loop-control
bridge-group 255 spanning-disabled
bridge-group 255 block-unknown-source
no bridge-group 255 source-learning
no bridge-group 255 unicast-flooding
service-policy input Lync
service-policy output Lync
interface Dot11Radio1.1200
encapsulation dot1Q 1200 native
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
interface Dot11Radio1.1234
encapsulation dot1Q 1234
bridge-group 254
bridge-group 254 subscriber-loop-control
bridge-group 254 spanning-disabled
bridge-group 254 block-unknown-source
no bridge-group 254 source-learning
no bridge-group 254 unicast-flooding
service-policy input Lync
service-policy output Lync
interface GigabitEthernet0
no ip address
duplex full
speed auto
interface GigabitEthernet0.1000
encapsulation dot1Q 1000
bridge-group 255
bridge-group 255 spanning-disabled
no bridge-group 255 source-learning
service-policy input Lync
service-policy output Lync
interface GigabitEthernet0.1200
encapsulation dot1Q 1200 native
bridge-group 1
bridge-group 1 spanning-disabled
no bridge-group 1 source-learning
interface GigabitEthernet0.1234
encapsulation dot1Q 1234
bridge-group 254
bridge-group 254 spanning-disabled
no bridge-group 254 source-learning
service-policy input Lync
service-policy output Lync
interface BVI1
mac-address 881d.fc46.c865
ip address 10.10. 255.255.254.0
ip default-gateway 10.10.
ip forward-protocol nd
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
bridge 1 route ip
line con 0
line vty 0 4
login local
transport input all
sntp server ntp2c.mcc.ac.uk
sntp broadcast client
end
LATHQWAP01#

Router Dead , when i applied QOS on virtual-temp interface for vpn !!

hi all ,
i have a simple brief topology below :
PSTN======(R1-7206)>F1=======F2>(R2-7604 catalyst)>>>F1=========Internet
i have two router
R2========>MLS 7604
R1======>cisco 7204
on R2 , Im doing matching to QOS by dscp , im matching acls ips from internet with dscp values :
here is CONFIG for matching :
Gateway7600#sh policy-map LLQX
Policy Map LLQX
    Class YOUTUBE
      set ip dscp af43
    Class FACEBOOKVIDEOS
      set ip dscp af33
    Class HTTP
      set dscp af23
    Class DNSQOS
      set dscp af13
    Class class-default
      set ip dscp af11
================
Gateway7600#sh class-map
Class Map match-all FACEBOOKVIDEOS (id 7)
   Match access-group name facebookvideos
Class Map match-all DNSQOS (id 8)
   Match access-group name dnsqos
Class Map match-all HTTP (id 6)
   Match access-group name browsing
Class Map match-any class-default (id 0)
   Match any
Class Map match-all YOUTUBE (id 5)
   Match access-group name youtube
Gateway7600#
=========================================================
on this router i applied this policy map on interfaxce F1 in direction
and here matching is well :
Gateway7600#sh policy-map interface gigabitEthernet 1/5 in
GigabitEthernet1/5
Service-policy input: LLQX
    class-map: rate-limit (match-all)
      Match: access-group name rate-limit
      police :
        4088000 bps 384000 limit 384000 extended limit
      Earl in slot 1 :
        139044930 bytes
        30 second offered rate 143032 bps
        aggregate-forwarded 134420937 bytes action: transmit
        exceeded 4623993 bytes action: drop
        aggregate-forward 22544 bps exceed 0 bps
    class-map: YOUTUBE (match-all)
      Match: access-group name youtube
      set dscp 38:
      Earl in slot 1 :
        132693939697 bytes
        30 second offered rate 212144928 bps
        aggregate-forwarded 132693939697 bytes
    class-map: FACEBOOKVIDEOS (match-all)
      Match: access-group name facebookvideos
      set dscp 30:
      Earl in slot 1 :
        10726758352 bytes
        30 second offered rate 20682720 bps
        aggregate-forwarded 10726758352 bytes
    class-map: HTTP (match-all)
      Match: access-group name browsing
      set dscp 22:
      Earl in slot 1 :
        56874058537 bytes
        30 second offered rate 92669832 bps
        aggregate-forwarded 56874058537 bytes
    class-map: DNSQOS (match-all)
      Match: access-group name dnsqos
      set dscp 14:
      Earl in slot 1 :
        160308954 bytes
        30 second offered rate 303552 bps
        aggregate-forwarded 160308954 bytes
    class-map: class-default (match-any)
      Match: any
      set dscp 10:
      Earl in slot 1 :
        67394864030 bytes
        30 second offered rate 126884864 bps
        aggregate-forwarded 67394864030 bytes
=================================================================================
now the problem is below
on router 7200 , it is LNS router connected with LAC roiuter for ADSL customers.
now here is config of policy map on 7200 router:
R11#sh policy-map
Policy Map MATCH_MARKS
    Class MATCH_YOUTUBE
      bandwidth 220000 (kbps)
    Class MATCH_FACEBOOKVIDEOS
      bandwidth 20000 (kbps)
    Class MATCH_HTTP
      bandwidth 100000 (kbps)
=========================================================
R1#sh class-map
Class Map match-all MATCH_FACEBOOKVIDEOS (id 2)
   Match ip dscp af33 (30)
Class Map match-all MATCH_HTTP (id 3)
   Match ip dscp af23 (22)
Class Map match-any class-default (id 0)
   Match any
Class Map match-all MATCH_YOUTUBE (id 1)
   Match ip dscp af43 (38)
==========================================================
here is virtual-template interface before i apply the QOS
R1#sh running-config interface virtual-template 1
Building configuration...
Current configuration : 352 bytes
interface Virtual-Template1
bandwidth 1000000
ip unnumbered Loopback0
ip tcp adjust-mss 1412
ip policy route-map private
no logging event link-status
qos pre-classify
peer default ip address pool bitsead1 bitsead2
ppp mtu adaptive
ppp authentication pap vpdn
ppp authorization vpdn
ppp accounting vpdn
max-reserved-bandwidth 90
end
=========================================
when i apply the command
(service-poliy output MATCH_MAKRS ) under virtual-template interface i have console logs :
Insufficient bandwidth 149760 kbps for the bandwidth guarantee (220000)
Insufficient bandwidth 149760 kbps for the bandwidth guarantee (220000)
Insufficient bandwidth 149760 kbps for the bandwidth guarantee (220000)
also i have
*Jul 9 22:28:38.242: Interface Virtual-Access2551 max_reserved_bandwidth config will not
take effect on the queueing features configured via service-policy
*Jul 9 22:28:38.250: Interface Virtual-Access627 max_reserved_bandwidth config will not
take effect on the queueing features configured via service-policy
*Jul 9 22:28:38.258: Interface Virtual-Access786 max_reserved_bandwidth config will not
take effect on the queueing features configured via service-policy
*Jul 9 22:28:38.266: Interface Virtual-Access623 max_reserved_bandwidth config will not
take effect on the queueing features configured via service-policy
*Jul 9 22:28:38.274: Interface Virtual-Access2559 max_reserved_bandwidth config will not
take effect on the queueing features configured via service-policy
*Jul 9 22:28:38.282: Interface Virtual-Access2281 max_reserved_bandwidth config will not
take effect on the queueing features configured via service-policy
*Jul 9 22:28:38.290: Interface Virtual-Access142 max_reserved_bandwidth config will not
take effect on the queueing features configured via service-policy
*Jul 9 22:28:40.262: %SYS-2-INTSCHED: 'suspend' at level 3 -Process= "VTEMPLATE Background Mgr", ipl= 3, pid= 278, -Traceback= 0x756FF0z 0x3439C58z 0x2778D70z 0x2CACCD0z 0x2CC63E0z 0x2CC7FF8z 0x2CADC74z 0x2CBE058z 0x2CA0340z 0x2CA04F8z 0x2E0BB18z 0x2D23378z 0x2D1825Cz 0x2D18738z 0x2E66FE0z 0x2D971ACz
*Jul 9 22:28:40.262: %SYS-2-INTSCHED: 'suspend' at level 3 -Process= "VTEMPLATE Background Mgr", ipl= 3, pid= 278, -Traceback= 0x756FF0z 0x3439C58z 0x2778D70z 0x2CACD28z 0x2CC63E0z 0x2CC7FF8z 0x2CADC74z 0x2CBE058z 0x2CA0340z 0x2CA04F8z 0x2E0BB18z 0x2D23378z 0x2D1825Cz 0x2D18738z 0x2E66FE0z 0x2D971ACz
after i apply it ,
the cpu is 100 % and the router got down !!!
now
what is the problem ????
here is ios for 7200 router
R1#sh version
Cisco IOS Software, 7200 Software (C7200P-ADVENTERPRISEK9-M), Version 12.4(24)T7, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Tue 28-Feb-12 12:53 by prod_rel_team
ROM: System Bootstrap, Version 12.4(12.2r)T, RELEASE SOFTWARE (fc1)
Bras1 uptime is 13 weeks, 1 day, 9 hours, 24 minutes
System returned to ROM by reload at 16:24:51 GMT+3 Tue Jun 17 2003
System image file is "disk2:c7200p-adventerprisek9-mz.124-24.T7.bin"
Last reload reason: Reload Command
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
Cisco 7206VXR (NPE-G2) processor (revision A) with 917504K/65536K bytes of memory.
Processor board ID 36858624
MPC7448 CPU at 1666Mhz, Implementation 0, Rev 2.2
6 slot VXR midplane, Version 2.11
Last reset from power-on
PCI bus mb1 (Slots 1, 3 and 5) has a capacity of 600 bandwidth points.
Current configuration on bus mb1 has a total of 0 bandwidth points.
This configuration is within the PCI bus capacity and is supported.
PCI bus mb2 (Slots 2, 4 and 6) has a capacity of 600 bandwidth points.
Current configuration on bus mb2 has a total of 0 bandwidth points.
This configuration is within the PCI bus capacity and is supported.
Please refer to the following document "Cisco 7200 Series Port Adaptor
Hardware Configuration Guidelines" on Cisco.com <http://www.cisco.com>
for c7200 bandwidth points oversubscription and usage guidelines.
1 FastEthernet interface
3 Gigabit Ethernet interfaces
2045K bytes of NVRAM.
250880K bytes of ATA PCMCIA card at slot 2 (Sector size 512 bytes).
65536K bytes of Flash internal SIMM (Sector size 512K).
Configuration register is 0x2102
==============================================================================
wish to Help ASAP
regards

hi ,
i did
the same issue ,
i did a TEST policymap that has 30 percent gurantee
but the same result!!!!!!!!!!!!!!!!
the router god down agian !
here is logs :
take effect on the queueing features configured via service-policy
*Jul 11 02:40:33.605: Interface Virtual-Access1896 max_reserved_bandwidth config will not
take effect on the queueing features configured via service-policy
*Jul 11 02:40:33.797: Interface Virtual-Access1317 max_reserved_bandwidth config will not
take effect on the queueing features configured via service-policy
*Jul 11 02:40:33.809: Interface Virtual-Access993 max_reserved_bandwidth config will not
take effect on the queueing features configured via service-policy
*Jul 11 02:40:33.817: Interface Virtual-Access1699 max_reserved_bandwidth config will not
take effect on the queueing features configured via service-policy
*Jul 11 02:40:33.981: Interface Virtual-Access254 max_reserved_bandwidth config will not
take effect on the queueing features configured via service-policy
*Jul 11 02:40:33.993: Interface Virtual-Access687 max_reserved_bandwidth config will not
take effect on the queueing features configured via service-policy
*Jul 11 02:40:34.001: Interface Virtual-Access35 max_reserved_bandwidth config will not
take effect on the queueing features configured via service-policy
*Jul 11 02:40:34.009: Interface Virtual-Access160 max_reserved_bandwidth config will not
take effect on the queueing features configured via service-policy
*Jul 11 02:40:34.017: Interface Virtual-Access1337 max_reserved_bandwidth config will not
take effect on the queueing features configured via service-policy
*Jul 11 02:40:34.029: Interface Virtual-Access1670 max_reserved_bandwidth config will not
take effect on the queueing features configured via service-policy
*Jul 11 02:40:34.037: Interface Virtual-Access1948 max_reserved_bandwidth config will not
take effect on the queueing features configured via service-policy
*Jul 11 02:40:34.049: Interface Virtual-Access1669 max_reserved_bandwidth config will not
take effect on the queueing features configured via service-policy
*Jul 11 02:40:34.109: Interface Virtual-Access1334 max_reserved_bandwidth config will not
take effect on the queueing features configured via service-policy
*Jul 11 02:40:34.117: Interface Virtual-Access151 max_reserved_bandwidth config will not
take effect on the queueing features configured via service-policy
*Jul 11 02:40:34.125: Interface Virtual-Access761 max_reserved_bandwidth config will not
take effect on the queueing features configured via service-policy
*Jul 11 02:40:34.137: Interface Virtual-Access810 max_reserved_bandwidth config will not
take effect on the queueing features configured via service-policy
*Jul 11 02:40:34.197: Interface Virtual-Access1522 max_reserved_bandwidth config will not
take effect on the queueing features configured via service-policy
*Jul 11 02:40:34.237: Interface Virtual-Access1692 max_reserved_bandwidth config will not
take effect on the queueing features configured via service-policy
*Jul 11 02:40:34.257: Interface Virtual-Access368 max_reserved_bandwidth config will not
take effect on the queueing features configured via service-policy
*Jul 11 02:40:34.305: Interface Virtual-Access1758 max_reserved_bandwidth config will not
take effect on the queueing features configured via service-policy
*Jul 11 02:40:34.317: Interface Virtual-Access2061 max_reserved_bandwidth config will not
take effect on the queueing features configured via service-policy
*Jul 11 02:40:34.325: Interface Virtual-Access1203 max_reserved_bandwidth config will not
take effect on the queueing features configured via service-policy
*Jul 11 02:40:34.337: Interface Virtual-Access188 max_reserved_bandwidth config will not
take effect on the queueing features configured via service-policy
*Jul 11 02:40:34.345: Interface Virtual-Access1975 max_reserved_bandwidth config will not
take effect on the queueing features configured via service-policy
*Jul 11 02:40:34.357: Interface Virtual-Access1172 max_reserved_bandwidth config will not
take effect on the queueing features configured via service-policy
*Jul 11 02:40:34.509: Interface Virtual-Access1647 max_reserved_bandwidth config will not
take effect on the queueing features configured via service-policy
*Jul 11 02:40:34.517: Interface Virtual-Access458 max_reserved_bandwidth config will not
take effect on the queueing features configured via service-policy
*Jul 11 02:40:34.609: Interface Virtual-Access608 max_reserved_bandwidth config will not
take effect on the queueing features configured via service-policy
*Jul 11 02:40:34.621: Interface Virtual-Access2128 max_reserved_bandwidth config will not
take effect on the queueing features configured via service-policy
*Jul 11 02:40:34.633: Interface Virtual-Access1167 max_reserved_bandwidth config will not
take effect on the queueing features configured via service-policy
*Jul 11 02:40:34.641: Interface Virtual-Access487 max_reserved_bandwidth config will not
take effect on the queueing features configured via service-policy
*Jul 11 02:40:34.653: Interface Virtual-Access1793 max_reserved_bandwidth config will not
take effect on the queueing features configured via service-policy
*Jul 11 02:40:34.665: Interface Virtual-Access2280 max_reserved_bandwidth config will not
take effect on the queueing features configured via service-policy
*Jul 11 02:40:34.769: Interface Virtual-Access839 max_reserved_bandwidth config will not
take effect on the queueing features configured via service-policy
*Jul 11 02:40:34.781: Interface Virtual-Access2311 max_reserved_bandwidth config will not
take effect on the queueing features configured via service-policy
*Jul 11 02:40:34.793: Interface Virtual-Access1788 max_reserved_bandwidth config will not
take effect on the queueing features configured via service-policy
*Jul 11 02:40:34.857: Interface Virtual-Access8 max_reserved_bandwidth config will not
take effect on the queueing features configured via service-policy
*Jul 11 02:40:34.869: Interface Virtual-Access2243 max_reserved_bandwidth config will not
take effect on the queueing features configured via service-policy
*Jul 11 02:40:34.881: Interface Virtual-Access580 max_reserved_bandwidth config will not
take effect on the queueing features configured via service-policy
*Jul 11 02:40:35.057: Interface Virtual-Access6 max_reserved_bandwidth config will not
take effect on the queueing features configured via service-policy
*Jul 11 02:40:35.065: Interface Virtual-Access1331 max_reserved_bandwidth config will not
take effect on the queueing features configured via service-policy
*Jul 11 02:40:35.077: Interface Virtual-Access1235 max_reserved_bandwidth config will not
take effect on the queueing features configured via service-policy
*Jul 11 02:40:35.177: Interface Virtual-Access1748 max_reserved_bandwidth config will not
take effect on the queueing features configured via service-policy
*Jul 11 02:40:35.189: Interface Virtual-Access2262 max_reserved_bandwidth config will not
take effect on the queueing features configured via service-policy
*Jul 11 02:40:35.205: Interface Virtual-Access2136 max_reserved_bandwidth config will not
take effect on the queueing features configured via service-policy
i want to ask a question , could this be from IOS ????

Limit access to guest network

In reading previous postings on limiting guest wifi access time on the AirPort Extreme, it sounds like you have to identify certain devices. my kids' devices only have access to the guest network. I was curious as to why the capability doesn't exist to limit the network availability period vs blocking specific devices. For instances, if my tween daughter has friends sleeping over, I don't want to just limit her access after a certain time, I'd like to limit all the kids' access By switching off the guest wifi.
any help is greatly appreciated!
thx, Sliceback

Apple did not provide the ability to do it.. you can turn off wireless manually but there is no other ability.. Apple routers are minimalist as many Apple designs are.. they do not provide more than absolute basic usage for stable family with no body cheating or ill using the network.. hence no firewall, no QoS, no logs, no snmp in new models. in fact as time goes on.. Apple is continuing to remove functionality rather than add it. That is their design philosophy.. if that doesn't work for you buy a wireless router with controls.. !! Most decent routers now have excellent controls, time limits and multiple guests.. check out the Asus line. eg AC68U.
Or use a cheap router with gargoyle firmware.. you can keep the AE as a wireless AP.. it is about as good as it gets.

Limit QoS

Similar Messages

Maybe you are looking for