Linksys App bug with port mapping

So I have the Linksys app installed on my Android phone. My router, WRT1900AC, is set up using port mapping. The port mapping is for an ssh app to control my 3 web servers. Each servers internal port is 22 and each servers external port is 20, 22, and 23 each one mapped to port 22. When signed in the the routher itself, not through the app, I can configuer these ports fine. However when I attempt to configuer these ports or the ip appress through the app, I get an error saying the port is in use. It seems the app is seeing the three servers using the same internal port and throwing an error.
Has anyone else experienced this?

I recommend you not use ports in the first 1000 unless they are for the standard server they are specified for. This is a good IT policy.
Example:
Port 22 External to internal IP Address of SSH server port
Port 21 External to internal IP Address of FTP server port
Instead use undefined ports in the higher end of the range.
Example:
Port 10001 External to internal IP Address of SSH server port
Port 10002 External to internal IP Address of SSH server port
The Linksys stock firmware will only do DNS proxing which isn't great for server networks.
For this application I recommend OpenWRT McWRT v1.0.5:
https://github.com/Chadster766/McWRT/releases
Install luci-ssl to enable SSL access and open router port 443 for standard secure remote access.
FYI:
Unless you have a USB to TTL cable for firmware recovery I recommend always flashing OpenWRT using the Linksys stock UI. This will put the Linksys stock firmware into the alternate boot image in case manual recovery is needed.
Do not delete the LAN, WAN and WAN6 interfaces. Pay attention to OpenWRT notices that say things are not reversible. OpenWRT can be unforgiving in those circumstances. If you have the $9.00 USB to TTL cable it won't matter because you can always load firmware through the boot loader.
OpenWRT McWRT has some issues:
https://github.com/Chadster766/McWRT/issues
Please remember to Kudo those that help you.
Linksys
Communities Technical Support

Similar Messages

HT1552 Im setting up a server with the port 25565 and im doing it with Port Map but the problwem is i cant seem to get it to work with my router. it goes through my macmini to the router and the expansion hardrive

Im setting up a server with the port 25565 and im doing it with Port Map but the problwem is i cant seem to get it to work with my router. it goes through my macmini to the router and the expansion hardrive

Im setting up a server with the port 25565 and im doing it with Port Map but the problwem is i cant seem to get it to work with my router. it goes through my macmini to the router and the expansion hardrive

Need help with port mapping on Airport Utility 6.1

Ive been trying to port map on my TC with Airport Utility 6.1 and failing miserably. Port still closed. Can anyone advise where Im going wrong? Am trying to set up my home camera to be viewed outside.
I managed to key in the ports etc under Network and Port Settings. But nothing works. I'm tearing my hair out.
Any suggestions to try would be helpful.
Thanks

Use the 5.6 utility.. it is much easier and I think works better.. although you cannot load 5.6 directly into 10.8 the version for Lion actually works fine.
Download 5.6.
http://support.apple.com/kb/DL1482
Download unpkg
http://www.macupdate.com/app/mac/16357/unpkg
Open the AU 5.6 dmg and drag the pkg over the open unpkg.. it will create the directory on the desktop. You can either run it from there or drag the utility to your utilties directory.
Take screen shots of each step. Post them here.
That way we can tell you where it has gone wrong.
What port exactly does the camera need open?
How are you connecting remotely?
ie do you have a fixed public IP?? If not how are you getting IP?
Is the TC the only router in the network.. it is irrelevant unless the TC is the one and only router.

Mail app bug with jumping to new line below signature

Hi!
Since day one of using Lion i have this incredibly annoying bug with Mail application.
I have a formated signature in all my emails. Sometimes when I am composing a mail (or rather replying for one) and when I hit RETURN on keyboard, cursor moves BELOW signature and inserts new line below signature - not in place when it was when I hit RETURN.
The same is when I have cursor in middle of my message and hit enter. Nothing happens - text ater place when cursor was when I hit enter is staying where it was but cursor moves below signature and enters new line in there.
Anyone has solution for this?

Triple-click the word "telnet" in the line below on this page to select the whole line:
telnet imap.gmail.com 993
Copy the selected text to the Clipboard by pressing the key combination command-C.
Launch the built-in Terminal application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Terminal in the icon grid.
Paste into the Terminal window by pressing command-V. I've tested these instructions only with the Safari web browser. If you use another browser, you may have to press the return key after pasting.
You should almost instantly get three lines of output below what you entered, the last of which is this:
Escape character is '^]'.
If there's no output within ten seconds, consider that a failure. If you get something different from the above, please post it in a reply. You can then quit Terminal.

Music app bug with iPad iOS 7.0.3

Hi,
My Music app was working fine until ios 7.0.3. Now, when I hit play, it goes from song to another really fast without actually playing them...
Is that happening to anyone else?
Thanks!
Chris.

Reset the device:
Press and hold the Sleep/Wake button and the Home button together for at least ten seconds, until the Apple logo appears.
If that doesn't help, tap Settings > General > Reset > Reset All Settings
No data is lost due to a reset.

Setup Airport Extreme Port Mapping for Swann DVR16-2600

Have a Swann video surv system and want to use iPhone 4 and Web to view camera displays remotely. It requires setting up port mapping for the DVR so it can serve ports 80 and 9000 to the remote display app and web screens.
Have signed up for a static public ip address from ISP since they do not allow port mapping using DHCP. Trying to setup so I can use the SwannView application on iPhone 4 and use Webview in browser to access/see security camera displays on/through the DVR. Not working correctly - only partial success.
Reconfigured Airport Extreme for the new ip address and tried to setup port mapping for dvr which needs a web port 84 and another port 9000. Can connect to DVR on internal network using the public static ip:84 and the internal static ip:84 but it only shows a SWANN splash page and an error about not able to load ipaddress:84/65536. Seems like something is preventing the Web display from completely launching - should see a login page but not getting it.
Airport is set to use static ips in the 10.0.1.2 to 10.0.1.10 range with the DVR assigned 10.0.1.5. Tried to set the port mapping for 84 and 9000 but not sure those are working correctly. Swann support tried accessing the DVR over the public ip address and they cannot get through. So suspect problem is with configuring the Airport Port Mapping settings and services, etc. on the Airport Extreme. I can get to the DVR internally using the public ip address:84 and the internal static ip address of the DVR:84 but support cannot get to it from external web.
Tried both Safari and IE 5 and both show same problem trying to launch the Swann login page, etc. iPhone Swannview app doesn't work either.
Any ideas about proper port mapping settings for those ports in the Airport Extreme? Is this correct setting for the Service Type: _http._tcp and do you need to add settings for the public and private udp ports. The udp port fields are empty. Only have entries in the Private IP Address and Public and Private TCP port fields.
Is there a way in Safari or IE5 to set security to see the public ip address as a friendly site and not block anything from loading?

Set port mapping for 85 (not 84) and 9000
Also, if you haven't, be sure to go into the Swann DVR setup and disable the "enable UPnP" option. The UPnP protocol will not work with Port mapping feature of the Apple Airport Extreme.

NAT configuration and Port Mapping for xBox

I'm looking for help with port mapping to open up the NAT for an xBox One. I'm working with the following network devices:
xBox One
DSL Modem: Embarq (ZyXEL) 660R series
Airport Extreme version 7.7.3
I understand the following from researching the issue:
The default settings for both devices block the ports needed for xBox Live.
Airport Extremes are not on the compatible list for xBox.
Port Mapping is better then creating a DMZ for the xBox.
The xBox needs its own manually set IP address.
I switched my Network>Router Mode from Off (Bridge Mode) to DHCP and NAT. I then created a DHCP Reservation and the Port Settings for that IP.
After doing this, the Airport would restart and display a warning - Double NAT. I figured this was because the 660 settings showed the NAT Mode to be SUA Only. The Edit Details link displayed an empty table where you edited the SUA/NAT Server Set. I switched from NAT Mode>SUA Only to None. So there was my Double NAT and I would have thought that would have removed one.
I also disabled the Firewall and Enabled the UPnP.
After restarts the Airport continued to display the Double NAT error. However, with the 660's NAT Mode set to None, the Internet was not there. Web browsers and email accounts replied with server not found.
Only with the 660 set to SUA Only and the Airport in Bridge Mode is the Internet accessible. I now have the details for the SUA filled out for the xBox's IP address and ports.
Hypothesis
Since both devices are acting as DHCP servers the port mapping is not working. Rather then have the 660 distribute IP addresses and then having the Airport distribute another range of numbers, I need to have both devices bridge and distribute one range of numbers. Currently the 660 is using the 192.168 range and the Airport is using the 10.0 range.
Am I correct? Any thoughts and suggestions are welcome.

Port forwarding through a double NAT.. is near impossible.. !!
And the xbox is so attuned to using UPNP it is very hard not to.. even port mapping is not a great fix. Since apple decided gamers did not count as users for Airports.. I think honestly it is best to bypass the airport and stick to upnp from the modem router.
What method of authentication does your ISP use? Because it is really better to use one router.
And in fact the router should be the Zyxel. If you plug the Xbox to the Zyxel running in full router mode, with the airport removed from the network does it work and open NAT??
If not replace the Zyxel with a modern listed router that is xbox compatible and bridge the airport to it.

Port mapping

I am having trouble setting up port mapping on my computer. the application I need to use with port mapping is telling my that the port is closed. I can't find it anywhere how to open up a port. can anyone help me out with this

Hello triumph1981. Welcome to the Apple Discussions!
I am having trouble setting up port mapping on my computer. the application I need to use with port mapping is telling my that the port is closed. I can't find it anywhere how to open up a port. can anyone help me out with this
AEBSn - Port Mapping Setup
To setup port mapping on an 802.11n AirPort Extreme Base Station (AEBSn), either connect to the AEBSn's wireless network or temporarily connect directly, using an Ethernet cable, to one of the LAN port of the AEBSn, and then use the AirPort Utility, in Manual Setup, to make these settings:
1. Reserve a DHCP-provided IP address for the host device.
Internet > DHCP tab
o On the DHCP tab, click the "+" (Add) button to enter DHCP Reservations.
o Description: <enter the desired description of the host device>
o Reserve address by: MAC Address
o Click Continue.
o MAC Address: <enter the MAC (what Apple calls Ethernet ID if you are using wired or AirPort ID if wireless) hardware address of the host computer>
o IPv4 Address: <enter the desired IP address>
o Click Done.
2. Setup Port Mapping on the AEBSn.
Advanced > Port Mapping tab
o Click the "+" (Add) button
o Service: <choose the appropriate service from the Service pop-up menu>
o Public UDP Port(s): <enter the appropriate UDP port values>
o Public TCP Port(s): <enter the appropriate TCP port values>
o Private IP Address: <enter the IP address of the host server>
o Private UDP Port(s): <enter the same as Public UDP Ports or your choice>
o Private TCP Port(s): <enter the same as Public TCP Ports or your choice>
o Click "Continue"
(ref: "Well Known" TCP and UDP ports used by Apple software products)

Is Time Capsule vulnarable with Upnp aka Port Mapping vulnerability?

As you also might have already heard about this quite huge upnp vulnerablity, I tried and failed to find out if Time Capsule or other Apple's network products are using this bugged libupnp library or not.
As a backup device it would be quite nasty if someone could hack in to the device and wipe all backups. US-CERT's list of manufacturers does not include Apple, so this is not helping much.
http://www.kb.cert.org/vuls/byvendor?searchview&query=FIELD+reference=922681&sea rchorder=4
So what to do, should we turn port mapping protocols off until Apple fixes this problem, or are we already safe with the Time Capsule's latest 7.6.1 version?

Apple do not use upnp.. they use their own entirely different protocol.. NAT-PMP so whatever the upnp vulnerability is, I doubt apple has it.

My location services is already on as well as with my facebook apps, but still i am unable to check in. what's wrong? even with my maps, it always say location unavailable. help please.

my location services is already on as well as with my facebook apps, but still i am unable to check in. what's wrong? even with my maps, it always say location unavailable. help please.

- The iPod uses the location of a nerby or connected router to determine it location based on a database of routers and their location. It appears that the routers near y are not in Appl'es database. As of yet, nobody here seems to know how to get routers added to the database.
- If you go to Strtbucks. McDonalds or another networks does the location show in the Maps app?

Port Mapping Problem with AEX

I have a new Airport Extreme and a problem that did not exist with the Airport. I connect a Toshiba network camera to an Airport Express, set as a WDS remote, with the netcam connected to the wired ethernet port of the Express. I can see the netcam, which also functions as a web server, on the internal 10.x.x.x address, and have reserved a discrete 10.x.x.x address via the MAC/DHCP reservation function of the Extreme. Just like the older Airport which did this without a hiccup, I should be able to map a port (e.g. 1200) on the public IP to port 80 of the internal 10.x.x.x address, then access the netcam on the internal network from any browser (http://67.x.x.x:1200). My cable modem is just that: no router involved other than the Airport Extreme. I'm using the latest Extreme and Express firmware, and am either missing something with the new Leopard firewall, overlooking something else, or dealing with a product flaw. Any help is appreciated and Happy Holidays.

I have forwarded the port (have tried several different ports actually) in what I think it the correct way: using the Airport Utility, connected to the Airport Extreme, and, under advanced options, selected port mapping, entered the public TCP port of 1200, then the private 10.x.x.x IP address of the netcam (which I can access from the internal network with no problem), coupled with the private TCP port of 80. I then attempt to access the netcam from the Internet by entering http://my cable modem IP address:1200 (or another port to which I've attempted to map). This method worked for two years with the Airport, but, with the Extreme and Leopard (simultaneous transition), I'm stumped. After reading other about other port mapping problems, I reserved an IP address for the netcam based on its MAC with no positive results. I also set the firewall through the Security icon in System Preferences to allow all incoming connections. Thanks for taking the time to respond.

Port Mapping problem with a Snow Base Station

I wish to enable port mapping with my Airport Snow Base Station. (SBS) I am using an Earthlink Efficient Stream 5667 DSL modem to my SBS. I am running firmware version 4.0.9 and connecting with 10.4.3.
So -- enabling port mapping requires that the IP address on my 10.4.3 computer doesn't change, and that I then map the ports. However, I can not manually assign an IP (say 10.0.1.201) as my 10.4.3 can not connect using either "DHCP with manual address" or "manually" (where the router and subnet mask match the DHCP assignment)
What should I do?

Do not use the "DHCP with manual IP address" - that is a mode not supported by most networking devices on the market.
What you should do: on your Mac, open System Preferences->Network->Show Airport->TCP/IP tab. Select to "configure manually". Then enter the following parameters:
- IP address: 10.0.1.201
- subnet mask: 255.255.255.0
- router/gateway IP: 10.0.1.1
- DNS IP: use either 10.0.1.1, or enter the actual IP address(es) of your ISP's domain name servers

Port mapping not working with 7.5.1

I am having trouble getting Port mapping working with the new 7.5.1 firmware. Port mapping is not working. Port mapping was working fine before update, now all attempts to connect from WAN on ports are rejected. Tested with: telnet <wan-ip> <port>
I have removed and re-added all port mapping entries - no luck. Power cycled several times - no luck.
Other info:
I have an: Airport Extreme (Simultaneous Dual-Band II) running Version: 7.5.1.
It is setup to "Allow this network to be extended"
Network is being extended with an Airport Express with 802.11n running 7.4.2

yeah. I noticed the same thing. now the splash screen comes on without the flashing green squares and just hangs. i tried unintalling and then reinstalling and still no go. kind of annoying but they will probably come out with an update pretty soon

I've a "bug" with the apps downloading. This one stops at the end and stays like that infinite. The app doesn't appears normally on the homescreen. Someone can fix this?

I've a "bug" with the apps downloading. This one stops at the end and stays like that infinite. The app doesn't appears normally on the homescreen. The app is on the home screen, and its downloading is blocked at its end, without showing the app like it should when it's finished downloadung. Does someone can help me and fix this please?

Hi Tom
Thanks for replying!
I had heard that these switches didn't stack unless everything was identical.
I only tried it at all out of pure desperation.
I've applied and tested every version 3 firmware in standalone mode via a console cable and xmodem.
They either never come up properly receiving decompression errors and reboot constantly in a loop.
Occasionally they stall / jam and stay there displaying the same error with no rebooting.
And twice out of 80-100 times I got it to boot to the username and password screen in standalone mode.
But as soon as I made a change it crashed and started the rebooting cycle again.

How to Replace New Maps app on ios 6 with Google Maps?

Can someone please provide the procedure to replace the new maps app on ios 6 with Google Maps?
Thank you

You can still use Google’s maps — on the Web. Visit maps.google.com and accept the offer to create a Home-screen icon for you. You won’t get spoken directions, but you’ll get written directions, public transportation details, live traffic reports and, of course, Google’s far superior maps and data. (In two weeks, you’ll be able to get Street View this way, too, says Google.) And you can install the Google Plus Local app for full access to Google’s more complete database of shops and businesses.
You can also use someone else’s app. Many good ones cost money, but the MapQuest and Waze apps are free and offer spoken directions; Waze also incorporates real-time information about traffic jams, accidents and speed traps, collected by thousands of iPhones and Android phones on the roads.
If you can wait a couple of months, you’ll be able to install Google’s own maps app; Google is busily readying one for the iPhone and iPad.
 Cheers, Tom

Linksys App bug with port mapping

Similar Messages

Maybe you are looking for