Lms credentials

Dear all,
im getting the follwing error
while i m uploading the file in Csv format
by modifying the previous one
Invalidfileformat: no Header information in the input file

If you are using Excel to edit CSV's make sure to remove the extra characters in the CSV. Here is an example of a modified CSV using Microsoft Excel 2007
// Microsoft 2007 Saved file with extra padded characters (BEFORE)
; This file is generated by DCR Export utility,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
Cisco Systems NM Data import, Source=DCR Export; Type=DCRCSV; Version=3.0,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
;Start of section 0 - Basic Credentials,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
;HEADER: management_ip_address,host_name,domain_name,device_identity,display_name,sysObjectID,dcr_device_type,mdf_type,snmp_v2_ro_comm_string,snmp_v2_rw_comm_string,snmp_v3_user_id,snmp_v3_password,snmp_v3_auth_algorithm,snmp_v3_priv_password,snmp_v3_priv_algorithm,snmp_v3_engine_id,rxboot_mode_username,rxboot_mode_password,primary_username,primary_password,primary_enable_password,http_username,http_password,http_mode,http_port,https_port,cert_common_name,secondary_username,secondary_password,secondary_enable_password,secondary_http_username,secondary_http_password
10.1.1.1,CoreSwitch1,test.com,,CoreSwitch1,,,,,,,,,,,,,,,,,,,,,,,,,,,
;End of CSV file,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
// You must clean up the extra characters (AFTER)
; This file is generated by DCR Export utility
Cisco Systems NM Data import, Source=DCR Export; Type=DCRCSV; Version=3.0
;Start of section 0 - Basic Credentials
;HEADER: management_ip_address,host_name,domain_name,device_identity,display_name,sysObjectID,dcr_device_type,mdf_type,snmp_v2_ro_comm_string,snmp_v2_rw_comm_string,snmp_v3_user_id,snmp_v3_password,snmp_v3_auth_algorithm,snmp_v3_priv_password,snmp_v3_priv_algorithm,snmp_v3_engine_id,rxboot_mode_username,rxboot_mode_password,primary_username,primary_password,primary_enable_password,http_username,http_password,http_mode,http_port,https_port,cert_common_name,secondary_username,secondary_password,secondary_enable_password,secondary_http_username,secondary_http_password
10.1.1.1,CoreSwitch1,test.com,,CoreSwitch1,,,,,,,,,,,,,,,,,,,,,,,,,,,
;End of CSV file

Similar Messages

LMS 4.01 :credentials vérification SSH enable don't work

I have a 3750 with tacacs authentication on Cisco Acs.
in SSH on the active element no worries.
I filled the credentials of the device in lms add/import managed device
But in inventory audits and credentials to create a job with verification to enable ssh mode user name and password,
the job failed.
Is this a known problem?
Have an idea?
Regards
Philippe

Hi,
Thanks for the update and glad it fix the issue. Kindly close this thread so that it will be helpful for other too.
Summary :- If you have customized prompts configured on the device that means when you try to login to device the Username --> look like "username" (notedown the lower case of "u") and Password --> password (notedown the lower case of "p"), in this case you need to put these credentials on tacacsprompts.ini file that is located at
CSCOpx\objects\cmf\data
So that file look like :-
[TELNET]
USERNAME_PROMPT=username:
PASSWORD_PROMPT=password:
After making the above change. LMS will try to login to device with lower case username and password and thus most of the issues like device credentials report and Sync Archive for the devices will be fixed.
Many Thanks,
Gaganjeet

LMS 3.2 credentials/username question

I recently installed the trial version of LMS 3.2 on a single server (10.1.1.1). Now my head is spinning over what credentials i'm using vs authorization to modify a routers config vs device config. etc etc.
I've added a bunch of devices, but I cannot configure any devices via LMS.
I added a user called lmsuser to my routers/swiches.
I added the loggin 10.1.1.1 comment to my routers/switches.
I added read and write community ("readstring" and "writestring" strings to my routers/switches).
Question
1) I currently log into the portal using username: admin. Is this used anywhere other than getting into the portal?
2) I created a credential set called "firstset" with a user called lmsuser and readstring and writestring community strings. Do I need to do something to associate "firstset" with each device in the DCR?
3) When configuring RME credentials, do I use the the IP 10.1.1.1?
4) In cisco view I see views of my devices. When I right click on a switch interface and select "disable" I end up with an error message about not having permission to make the change. What secret handshake is required to make this happen?
I feel like I'm just not connecting the dots here. Thanks in advance.

1. No. These credentials are only used to access LMS applications (the portal, command line, etc.). They are not used to communicate with devices.
2. It depends on how you are adding devices to LMS. Each way (manual add, Discovery, import) allow you to choose a credential set, or use an automatic credential set. If you choose automatic, then a credential set will be applied to your devices based on the rules you have defined. Note: credential sets are only automatically applied when a device is added to DCR. You can choose to manually apply credential sets later, but if you modify a credential set after a device is added to DCR, those changes will not automatically be applied to your existing devices.
3. I don't understand. This is the IP of the LMS server. I'm not to sure what "RME credentials" you are referring, but I can't imagine where you would add 10.1.1.1 with any credentials.
4. You need an SNMP read-write credential (e.g. community string) configured for the device in DCR (i.e. under Common Services > Device and Credentials > Device Management).

Credentials in LMS 3.2

I'm not sure what I'm missing but I can't for the life of me figure out where to set up the SSH and enable credentials in CiscoWorks. I've been searching for a while now and I'm worried that I may be going crazy. I know that under RME there is a section for device credentials but the only option it gives is for SNMP, HTTP, Secondary, and default credentials. I KNOW I've seen where I can put in telnet/ssh/etc credentials in one spot but now I can't find it.
I'm trying to refresh the config archive but it's returning errors on SSH communication.
Any help would be appreciated!
Thanks in advance

I think the confusion stems from the new "credential sets" function introduced in LMS 3.2. The idea is "Now you can create multiple sets of default credentials and assign the sets based on policies, that is, IP address, host name, or display name."
Figures 26 & 27 illustrate the new credential sets concept:
http://www.cisco.com/en/US/prod/collateral/netmgtsw/ps6504/ps6528/ps2425/white_paper_c07-552114.html
Since you're looking to change passwords, I believe you will need to 1) update the existing Credential Set(s), and 2) do a mass-update of existing devices, due to the following caveat:
http://www.cisco.com/en/US/docs/net_mgmt/ciscoworks_common_services_software/3.3/user/guide/dcr.html#wp1958697
"The devices that are already added or imported into DCR will not be affected if you edit the values of the default credentials or remove the default credentials from DCR."

Invalid credentials report LMS

Hi there,
I want to know if there is a way to show invalid attempts to access to my different equipements on LMS.
For example, Show an alarm each time someone tries to access to a switch with an invalid credentials.
Thank you in advance

for failed login attempts to the switches, configure the following in global config mode:
login on-sucess log
login on-failure log
and you should get syslog messages on succesfull and failed login attempts.
Additionaly, you can define an automatic action on this specific syslog message to send you and e-mail based on this message

Cisco Works LMS snmp v3 credentials

I'm attempting to get a switch managed via SNMP v3 with CiscoWorks LMS 3.1 but I keep getting an error. I'm using the same User, Group names and also the same auth and priv credentials but I keep getting the error:
User is not authorized to perform the task on device.
I'm not sure what I'm missing.

Hi Florian,
actually the ACS 5.2 is not supported in CS 3.2
here is a list of the supported ACS servers under LMS 3.1
http://www.cisco.com/en/US/docs/net_mgmt/ciscoworks_common_services_software/3.2/user/guide/admin.html#wp865998

LMS 4.0 - credentials

Hello,
I installed new switchs on my network and I have others credentials than the oldest switches. I created a new credential set name with my new username and password (Admin -> Network -> Device Credential Settings -> Default Credential Sets)
I'm not sure if it's the good way how to apply this new profile to my new switches. I created a default credential sets policy configuration with the hostname for my new switchs and the credential sets to use.
I generated a verfication credential report but the result is that I have not the correct account and password for Telnet and SSH.
Could you please help me?
Thanks.

A little mistake. Not only CFM, all LMS4.0 modules cannot SSH to the managed switches.
Regards
Hubert

Upgrade from LMS 3.0.1 to LMS 3.1 or 3.2 and problem with devices update

Hello
How to upgrade from LMS 3.0 December 2007 update to LMS 3.1 or LMS 3.2. The problem is the large number of C2960S-24TS-L switches that my organization has and cannot managed them..
I tried to upgrade devices through Software Center but always Ciscoworks informs me with the following message.
"Error while downloading package information from Cisco.com for the selected products. See the log file for details".
Also i can not run EOL/EOS inventory report. The message is
" INVREP0102: Cisco.com user credentials are invalid. Enter correct credentials." I check my credentials and is right.
The server has access to www through proxy without any restrictions.
In the past I've already updated devices through the software center. Also in the past i ve run EOS/EOL inventory reports.
The LMS 3.0 December 2007 has the following products
LMS
3.0.1
16 May 2008
CiscoWorks Common Services
3.1.1
02 Jul 2009, 07:44:58 EEST
2.
Campus Manager
5.0.5
11 Oct 2009, 07:36:10 EEST
3.
CiscoView
6.1.7
02 Jul 2009, 07:45:05 EEST
4.
CiscoWorks Assistant
1.0.1
02 Jul 2009, 07:45:05 EEST
5.
Device Fault Manager
3.0.5
12 Jun 2010, 07:31:48 EEST
6.
Internetwork Performance Monitor
4.0.1
02 Jul 2009, 07:45:11 EEST
7.
Integration Utility
1.7.1
02 Jul 2009, 07:45:14 EEST
8.
LMS Portal
1.0.1
02 Jul 2009, 07:45:16 EEST
9.
Resource Manager Essentials
4.1.1
02 Jul 2009, 07:45:17 EEST
Has anyone knows what can be the problem??.
Thanks

Hi,
the problem to access cisco.com is because of a "bug". Its ID is CSCto46927.
http://tools.cisco.com/Support/BugToolKit/search/getBugDetails.do?method=fetchBugDetails&bugId=CSCto46927
Symptom:
After the 16th of June 2011 LMS will no longer be able to download Software and Device Package updates, or PSIRT and End of Sale/Life information from CCO
Conditions:
Hosted services in Cisco.com that are being leveraged by LMS, for downloading the latest Software and Device Package updates, as well as the PSIRT and End of Sale/Life information are being migrated to a new framework and the old services will be retired.
This will affect all LMS 3.x and 4.x versions.
Refer to https://supportforums.cisco.com/docs/DOC-16806 for more information
Workaround:
Users of LMS 3.2.1 , 4.0 should install the patch that can be downloaded from cisco.com
Users of earlier version will need to upgrade to LMS 3.2 and then install the LMS 3.2 SP1 patch set before installing the patch"
Because of that it is necessary to upgrade not only to 3.1 or 3.2, you need 3.2.1 to get the patch and then access to cisco.com again.
The question about the better way for updating I can't answer. I did a update to 3.1 and then to 3.2. But I think you will find the requirements for the updates in the notes for them.
But I can't find LMS 3.1 in the cisco download center. There is only 3.2 and 3.2.1 available for me.
Sven

Upgrading to LMS 4.0.1

After the installation LMS 4.0 I make Upgrading on LMS4.0.1. The process remains stand with the message "File Copy in progress..." during several hours. After the Reboot of the server it points me Cisco Works again with LMS 4.0 starts.
OS Version: Windows 2008 R2

Hi
Does any one know how to setup the Lms 4.0 i have loaded LMS 4.0 and also configured all basic settings, i am able to figure out how to add the device and check the verison treee etc,,
after adding the device and try to veiw the device the below error message getting.,,
The device is not available in the device credentials repository or you are not authorized to view the device details.
i am using admin account to do this job.
can some one help me on how to add device into lms 4.0 and check the config .
SS

Config collection fails occasionally in LMS 4.2

Hello,
In recently installed LMS 4.2 archive collection is failing from time to time for random number of devices with error:
      "Execution Result: CM00139 Could not archive config Cause: Action: Verify that device is managed and credentials are correct. Increase timeout value, if required."
     We have sceduled config collection job to run every day. Credentials are ok. The LMS data is restored from LMS 3.2. Timeout seeting is the same as in LMS 3.2 and we never had this problem before.
     Somtimes it is working for 10 days correctly, and then one day it is not successful for 70 out of ~150 device. Then t is successfull for few days, then again fails for 86 devices. Collction is scedueld in the evening so devices are not overloaded, nor there is some other job in LMS running at the same time.
     Any ideas?
     Thanks,
     Marija
I

The following did resolve my issue
The bug is fixed in the one of the latest device packages for LMS, SharedSwimIOS.RME525.v2-13-3. The release notes for it is here: http://www.cisco.com/web/software/283418817/118429/SharedSwimIOS.RME525.v2-13-3.readme.txt
Before applying that device package update, the following prerequisites need to be met:
- LMS 4.2.5
- MDF 1.92 (or higher) update : https://software.cisco.com/download/release.html?mdfid=284259296&flowid=37207&softwareid=283716219&release=Mdf.%201.92&relind=AVAILABLE&rellifecycle=&reltype=latest
- LibSwim.RME525.v2-13-1.zip & SharedDcmaIOS.RME525.v5-1-2.zip device packages already installed. Those two files and the SharedSwimIOS.RME525.v2-13-3 file can be found here: https://software.cisco.com/download/release.html?mdfid=284259296&flowid=37207&softwareid=283418817&release=AutoDev%285.8%29&relind=AVAILABLE&rellifecycle=&reltype=latest

Lms 4.1 prime psirt/eox no data available in the report

Hi:
I´m running LMS 4.1 Prime for Windows.
I tried an immediate report with PSIRT/EOX Report option: Cisco.com
The job succeeded, but without any data in the report
<TABLE style="WIDTH: 100%" border=0 cellSpacing=2 cellPadding=2 align=right mcestyle="width: 100%;">
No data available in the report. The problem could be any one of the following:
<TD style="COLOR: #686868" bgColor=#ffffff height=24 vAlign=top align=left mcestyle="color: #686868;">1. No PSIRT data available in the LMS database for the selected device(s).
2. PSIRT/EOX system job might not have run, or might have failed.
3. You might have entered the wrong cisco.com credentials.
Then I tried logging to Cisco.com (with the same user/password as configured in LMS) and download the PSIRT_EOX_OFFLINE.zip file.
I unzipped it and put it in the folder C:/PROGRA~1/CSCOpx/files/rme/jobs/inventory/reports/EOX_PSIRT/local_xml (please read \ instead of /, because it is wrong in the LMS display).
I set SIRT/EOX Report option: local
And again, the job succeeded, but without any data in the report (same message as before)
What do you think is happening? How could I debug the process?
Thanks a lot
Julio
PD: I`m selecting old devices to be sure that they already had an EOL/EOS.

Sorry, the copy/paste didn´t work as expected, here it is again:
Hi:
I´m running LMS 4.1 Prime for Windows.
I tried an immediate report with PSIRT/EOX Report option: Cisco.com
The job succeeded, but without any data in the report
No data available in the report. The problem could be any one of the following:
1. No PSIRT data available in the LMS database for the selected device(s).
2. PSIRT/EOX system job might not have run, or might have failed.
3. You might have entered the wrong cisco.com credentials.
Then I tried logging to Cisco.com (with the same user/password as configured in LMS) and download the PSIRT_EOX_OFFLINE.zip file.
I unzipped it and put it in the folder C:/PROGRA~1/CSCOpx/files/rme/jobs/inventory/reports/EOX_PSIRT/local_xml (please read \ instead of /, because it is wrong in the LMS display).
I set SIRT/EOX Report option: local
And again, the job succeeded, but without any data in the report (same message as before)
What do you think is happening? How could I debug the process?
Thanks a lot
Julio
PD: I`m selecting old devices to be sure that they already had an EOL/EOS.

Data collection problems in LMS 4.0

Hi, we have some devices in our LMS 4.0 where Data Collection cannot be collected. The strange thing is that some days ago they were working fine and we have SNMP connectivity. We have deleted the devices and have added them again but the problem still persists, how can we fix it?

From the LMS server do the following:
1. ping the devices that you cannot collect their data
2. test the snmp connection to those devices using snmpwalk
go to CSCOpx\objects\jt\bin
snmpwalk -v 2c -c 1.3.6.1.2.1.1.2
3. test the credintials against those devices (Inventory> Job Browsers> Device Credentials Verification)
For any failure in 1 or 2 usually this is a firewall problem. Check if snmp and icmp ports are open or not.
For 3 failue check the credintials from (Inventory> Device Administration> Add / Import / Manage Devices)
I hope this help

Cisco LMS 4 IEFrame

Hello,
i have added a IEFrame in a LMS Dashboard containing some information about Cisco WCS. I works fine, just there is an issue when i open my Dashboard and I didn't start WCS before the IE Frame not showing the information. I tried to set the credentials in the IE Frame Configuration but still the same.
Further i'd like to add some Ie Frames showing authentication trends from my ACS. But i have no idea how to get the correct URL from the ACS dashboards.
appreciate any feedback
alex

You will likely need to login to WCS before the IFrame portlets will work. I think prior versions of WCS provided the ability to use the credential interface within the portlet, but newer versions use a cookie/session based authentication mechanism.
I don't have a recent version of ACS handy anymore to look at, but I don't recall seeing any widget-like constructs in 5.2. What I typically do when I need to find URLs is right-click on pages or frames and get info. The info window will contain the direct link.

LMS Software Image Management - Telnet failure

Hi all,
I had a problem with Software Image Management for the upgrade of a switch.
It seems that at the end of the upgrade, CiscoWorks was unable to save the configuration with telnet.
Yet, telnet seems to be ok because CiscoWorks manages to connect to the switch at the beginning of the upgrade.
Updating config file during software upgrade processDevice running-config is modified but failed to save the running-config to startup-config.Cause: Could not detect SSH protocols running on the device
TELNET: Failed to establish TELNET connection to 10.1.3.4 -Cause: Authentication failed on device 3 times.
I sent attached the logs of the upgrade.
Thank you in advance.

Hello,
The job fails last night after timeout.
I have reschedule job this morning for 2 switchs :
2960 with telnet and ssh enabled
2960 with telnet enabled only
The device credentials verification job seems to be coherent :
Device Name
Read
Community
Read Write
Community
Telnet
Enable
by Telnet
SSH
Enable
by SSH
1.
switch04-d
Ok
Ok
Ok(Primary Successful)
Ok(Primary Successful)
Failed to connect.
Did Not Try
1.
switch03-d
Ok
Ok
Ok(Primary Successful)
Ok(Primary Successful)
Ok(Primary Successful)
Ok(Primary Successful)
But the job fails again cause telnet authentication failed on device 3 times.
I do not understand why LMS does not use ssh if possible at the finish of the job? Why telnet authentication fails ?
Thanks in advance.

Cisco pix 525 and 515 cannot archieve configuration in LMS 3.0.1

Hi,
we have several cisco pix 525 and 515 cannot archieve configuration in LMS 3.0.1
Any help would be greatly appriciated.
Thanks in advance
Samir

Hi,
Here is the output.
*** Device Details for ***
Protocol ==> Unknown / Not Applicable
Selected Protocols with order ==> TFTP,SSH,HTTPS
Execution Result:
RUNNING
CM0151 PRIMARY RUNNING Config fetch failed for ********* Cause: SSH: Failed to establish SSH connection to 10.192.18.10 - Cause: Authentication failed on device 3 times.
Action: Check if protocol is supported by device and required device package is installed. Check device credentials. Increase timeout value, if required.
But when I do mangement station to Device it gives me following results:
Interface Found: 10.192.18.10
Status: UP
Test Results
UDP     Failed
      sent: 5 recvd: 0 min: 0 max: 0 avg: 0 timeout: 2 size: 64 protocol: udp port: 7
TCP     Failed
      sent: 0 recvd: 0 min: 0 max: 0 avg: 0 timeout: 0 size: 0 protocol: tcp port: 7
HTTP     Failed
      sent: 0 recvd: 0 min: 0 max: 0 avg: 0 timeout: 2 size: 33 protocol: http port: 80
TFTP     Failed
      sent: 5 recvd: 0 min: 0 max: 0 avg: 0 timeout: 2 size: 25 protocol: tftp port: 69
SNMPRv2c(Read)     Okay
     sent: 5 recvd: 5 min: 0 max: 0 avg: 0 timeout: 2 min_size: 1472 protocol: snmpv3_get port: 0
SNMPWv2c(Write)     Failed
      sent: 5 recvd: 0 min: 0 max: 0 avg: 0 timeout: 2 min_size: 1472 protocol: snmpv3_set port: 0
SSHv2     Failed
TELNET     Okay
Waiting for your reply.
Samir

Lms credentials

Similar Messages

Maybe you are looking for