Low signals after upgrading TV firmware

I have a UA40D6600WR with an internal WIFI connectivity, after upgrading the company provided firmware last week i see only one bar of Wi-Fi signal strength in Skype app when calling my contacts, due to this I think the contacts video is not clear, wireless router was placed behind the TV. Do we have any workaround for increasing the signal strength in my TV?. Before upgarding the firmware it was working perfectly allright. If we dont have a solution for this please dont upgrade your TV firmware.

nothing??

Similar Messages

  • Choppy video streaming after upgrading E4200 firmware to ver. 1.0.03

    Video streaming was fine until I upgraded the firmware. Is it possible to downgrade the firmware?

    You mentioned in your post that you upgraded the latest firmware. So after upgrading the firmware did you reset the router? It is recommended to reset the router after firmware upgrade.  Steps to reset the router:
    Push the reset button on router for 30 seconds, turn off the router wait for 30 seconds and then power it on. After this process reconfigure the router. Power light should blink when you perform the reset process.
    After the process reconfigure the router as per the ISP setup.. Then try to do the following steps:
    A] With the help of Cisco Connect Software (if at all you have installed the router with the help of this software)
              1] Open the software and go to the option which says "Router Settings"
              2] Then click on the option which says "Advanced Settings" which will take you to the router's configuration page.
             3] Lower the MTU (Maximum Transmission Unit) from 1500 to 1400 or less (usually found on your router's main/ basic setup page)
             4] Then go to the Wireless tab, keep network mode as mixed,
     For Channel Settings of 2.4 GHz you can make Channel Width to 20 MHz only and Channel to 6, 9, 11..
     For Channel Settings of 5 GHz you can make Channel Width to 20 MHz only and Channel to 40 or 161...
    B] If you haven't installed Cisco Connect then you can log on to the router's user interface using it's default IP address in the browser which is 192.168.1.1 and type in 'admin' as the password leaving the username field blank. This will take you to the router's web interface and then follow steps as mentioned above to make the changes.

  • USB Share broken after upgrade to Firmware 1.05.36

    Hi, Problem after upgrade to Firmware 1.05.36.  When connecting USB disk there no share created for the newly connected disk. The result is: Broken functionality backup to USB diskBroken functionality restore from USB disk It worked OK before thefirmware upgrade (I have been using this a lot). I have checked through ssh login: the disk mounts ok. Please fix!!

    Yes, that's exactly what I mean - the shares that are automatically created when you insert the drive (ie the functionality you seem to have lost). There's no setting to enable/disable that, at least that I know of. It should just always automatically do it. The shares themselves are just links in the /shares folder, to the relevant mount folder if what I can see on my MCM via SSH is what I think it is. You may be able to manually make the links yourself via the command prompt as a work-around. Please note that I haven't tried this myself, as my one works. But what I would do is try and install the firmware image again over the top of your current one. You can download it manually from this page and then install it via the dashboard using Settings > Firmware Update > Manual Update. There should be a button there that you press and point it to the firmware image file you downloaded and stored on your local machine. If the button isn't there, try a different browser (I find on my Windows machine it doesn't appear under Chrome, I have to use IE for that job).

  • Problem after upgrading New Firmware 14.1.G.1.534. Asking for Password when i click settings menu

    Problem after upgrading New Firmware 14.1.G.1.534. Asking for Password when i click settings menu, for which i never kept any password. 
    Any DEFAULT Password so that i can unlock the settings menu.

    That's quite odd, just repeat the update process
    Update Service (SUS)
    http://www.sonymobile.com/gb/tools/update-service/
    http://www-support-downloads.sonymobile.com/Software%20Downloads/Update_Service_Setup-2.11.12.5.exe
    PC Companion (PCC)
    Bridge (for Mac)
    Alternatives on How to backup Xperias
    http://talk.sonymobile.com/thread/36355
    "I'd rather be hated for who I am, than loved for who I am not." Kurt Cobain (1967-1994)

  • Low cell signal After upgrade to IOS 5.1.1 to my iphone 4

    After upgrading my iphone 4 to IOS 5.1.1 ,my cell signal becomes very low and after some time it shows no service.

    Do you know if your "Cell Network Search" under "Location Services" is on or off. I have been struggling with the same issue, on and off and this is one of the settings I have changed recently.

  • WIFI Quit after upgrade to firmware 3.1.

    My WIFI quit after upgrading from 2.1.1 to 3.1. It worked twice since the upgrade for a period of an hour or so. I have tried to reset the network, All settings, serveral reinstallation of the firmware. I also Tried to manually enter in my WIFI information, with no success. I tried everything. I can see wifi information when I go into the general settings>About> Wi-Fi Adress 00:1c:b3:48:ce..... My warrenty is no longer valid. Any suggestions???

    I've now posted these changes at two other WiFi threads. Try these Settings changes:
    The Setting changes are:
    Fetch New Data > Push: Off
    Fetch settings are set to Manual & in Advanced all is set to Manual.
    My iPhone also lost WiFi but with the changes above it now connects though it takes a bit longer to find the signal. No longer have Push but WiFi is more important, to me anyway. Another iPhone user had success with the above changes.
    Good luck.

  • Problems with TV Out signal after upgrading to iOS 5.1

    Has anyone experienced problems with TV Out signals on their iPad 2 using the Apple HDMI Adapter after upgrading to iOS 5.1?  I am trying to connect to my HDTV after upgrading and cintunally receive an "Unsupported Video Signal" message with a blank/back screen.  Prior to upgrading, I had no connection problems and could view TV Shows, Movies, Music Videos, Keynote, etc...without problems.  I've been unable to find any resolution to this problem, even followed Apple guidance to detach and reattach the HDMI adapter without success.  Seems like a software bug to me and it's a major problem when trying to conduct business or personal activities.  Hopeing Apple has a fix in work already...anyone else have any ideas?  Thx in advance...

    Try a reset. Press & hold the Power and Home buttons together for 10+ seconds, ignoring the red power-off slider, until you see the Apple logo. It is safe to do, there should be no content loss. It is the same as rebooting your computer.
    If that does not work, restore the iPad to the factory settings.

  • Web Search fails on E52 after upgrading to firmwar...

    After upgrading my E52 to firmware version v31.012, I'm not able to do web search, always fails. When I go back and resend query it works. I still waiting new incoming updates will correct this, but even the v34 didn't resolve this problem. I was able to do search directly when I bought the phone and before  v31.012. Did anybody face this problem?

    If that message is on your home page and the home page is similar to www.google.com/firefox, then change your home page. The old Firefox/Google home page is no longer being maintained by Google and will give you that erroneous message.
    Change your home page to '''''about:home''''', the new built-in, updated Firefox/Google home page
    *See --> https://support.mozilla.org/en-US/kb/How%20to%20set%20the%20home%20page
    Information submitted with your question indicates that you are using the latest released version, Firefox 10.0.2.
    *See --> https://support.mozilla.org/en-US/kb/Finding%20your%20Firefox%20version
    '''If this reply solves your problem, please click "Solved It" next to this reply when <u>signed-in</u> to the forum.'''

  • IPhone 4 does not catch signals after upgrading to iOS 7

    I am a iPhone 4 user. It does not catch proper signal strength in home after upgrading to iOS 7 whereas it does catch it on the outside. It worked perfectly with previous iOS versions. Please help me out.

    Does anyone have any solution???
    Reply ASAP...
    My iPhone has turned into an iPod since l upgraded...

  • Weak 3gs wifi signal after upgrade to ios6

    Anyone experienced the same thing after upgrading their 3gs to ios6?
    I noticed that wi-fi signal became weaker.
    I am on the same spot inside the house and the 3gs cannot detect my connection.

    I have the same issue since I upgraded to iOS 6. My 3GS (end of 2009) has extremely weak WiFi signal from areas I used to get very strong signal. I now need to be within 12 inches of my home WiFi access point for the phone to pickup the signal. And the connection drops as soon as I am getting more than 12 inches away.
    Same behavior from our WiFi at work -- I can no longer connect on the corporate WiFi from my office space!!
    I also went to the Apple store in San Jose, and the phone was not even able to pickup the Apple WiFi signal from the middle of the shop!!! This very same phone was working flawlessly on 5.1.1 before the iOS 6.0 upgrade. I tried all the tricks people said to no available. Nothing works. My phone is useless now because of Apple!! Isn't this a trick to force people changing to newer phone?? Now I am using too much from my 3G plan and it will cost me moneys because of this..
    Apple starts to look like a Lemon to me..

  • Weak Wifi signal after upgrading Iphone to 4.1

    I had a perfectly working Wifi home connection on a new iPhone 4 running 4.01 and 4.02.
    After upgrading to 4.1 yesterday, the wifi has gone bad: the connection strength has dropped - at least- 10 fold. I have to stand next to the router to get connected. Before I had excellent connection at long distances.
    Nothing has changed to the router, and I still have excellent wifi connectivity with my MacBook, iPad, and another iPhone.
    Seems that the upgrade to 4.1 somehow broke the wifi connectivity.
    Help!
    S.

    I am experiencing hte same thing. Except I started with 4.1 and I am getting very weak signal compared to my buddies iPhone which is also running 4.1. Which is weird .. I guess I will call in tommorow any ideas ??

  • Itunes won't detect ipod touch after upgrade to firmware 1.1.4

    I am in desperate need of help. My 16GB Ipod is no longer being detected by iTunes.
    I decided to upgrade the firmware to 1.1.4. through iTunes. The update wasn't interrupted and i can see no issues during the procedure. when the update was completed, my iPod had no content in it and it wasn't showing up in iTunes.
    Here's what i've tried so far to correct this:
    - Uninstalled iTunes and all other apple related software and then re-installed
    - tried different USB ports on my laptop
    - Reset all setting within the ipod
    - Run the iTunes diagnostic. It error's out during the sync test.
    I've tried to find any other similar example on other sites but haven't been successful.
    Please help.

    These are other hints http://www.copytrans.net/helpcopytrans.php#22
    That might help.

  • Problem mounting network drive after upgrading router firmware

    Hi guys,
    It's been a while since I last posted a question of my own here, but I'm at my wits end. As I may have mentioned, I live in France, and my ISP is Free (no, not free, Free...). I've got what they call a "box" here, i.e. a sort of super-modem that will let you connect to the Internet via xDSL (and soon VDSL2), receive hundreds of TV channels, read BluRay discs, store files (videos, music, photos, what have you) on a integrated NAS, place and receive phone calls, whether via a landline (DECT) or, since recently, through a femtocell.
    All in all, the package is impressive and works flawlessly. But...
    (Of course, there had to be a "but)
    ... Yesterday, I let my "box" (it's called a Freebox Revolution, or Freebox V6--for Version 6--by the way) upgrade its firmware, reboot as it always does in such circumstances, and  since that,  the NAS won't mount in the Finder the way it used to under the Shared left pane.
    Now, every time I reboot my Mac, I have to open a browser windows and type "smb://mafreebox.freebox.fr" in order mount the NAS in the Finder. I've saved the credentials (login, no password) in the keychain, hoping it would help, but it doesn't. I've got a PC running Windows 8.1 Preview at the moment, and created a shortcut to the NAS on the Desktop. Guess what? I double-click on the shortcut, and sure enough, I can access the content of the NAS from Windows, but not from the Mac.
    I must add that I haven't changed anything on the Mac since, or before, upgrading the "box" firmware.
    Any ideas?

    OK, you must think I'm going bananas, but my issue is gone... For now...
    Seriously, what do you guys think about this problem with network drives mounting or not, depending on, I don't know, the weather, maybe?

  • N73 - Another Problem after upgrade the firmware t...

    Except the slow contact search problem (solved by Unplug the battery), I still suffered from some application install problems.
    1. Whenever I restart the phone, a message 'Installing' always poped up, and the phone not responding for around 2-3 minutes. And then an error message 'Unable to complete ....' prompted.
    2. The K-Mobile Client application losted after upgrade, and I tried to reinstall it , but resulted error by 'File corrupted'

    Usually that annoying installation process in the beginning can be removed by deleting that installation file in MMC>\Private\10202dce . Most of them does not have the real title of the application. To delete the right one, you need to go to the application manager first and look at the title of the application that cannot be installed nor removed. Ones you know the titles, plug in ur phone to ur computer and browse MMC>\Private\10202dce , some title of the applications from the application manager should be listed there. Delete whatever you find is listed "not installed" in application manager (app cannot be installed or removed), but first make sure to make a backup of it somehow just in case you make an error. After you delete the file/files restart ur phone. The annoying installation process should not appear anymore. Note that by just removing that file may not fully remove the files it created. For advice, if you install applications in ur phone make sure you have backup of them stored in ur computer so that if the installed applications in ur phone stops working properly all you need to do is to reinstall using the original/backup sis files.
    - Is this a Signature? -

  • Too many errors after upgrading the firmware to 1.0.3.10 on Cisco RV180W wireless router

    My company purchased one Cisco RV180W wireless router few days ago and it worked normal with default firmware version of 1.0.0.30. Today I upgraded the firmware to version 1.0.3.10, the users can still access this router via wired and wireless devices, but on the dashboard I observed two major problems, one is the CPU utilization always shows 100%, another is the more and more errors appearing, on the Syslog Summary panel "Error" log has been up to 625 and is still increasing, there is one message repeatedly displaying in the log, see in below:
    Wed Nov 13 13:55:25 2013(GMT+0800) [rv180w][System][PLATFORM] /pfrm2.0/bin/bwLimitConfig /tmp/system.db 18 dot11STA 100 failed. status=-1
    Who can tell me what does this error message mean and how to elinate this error message ?  also how to deal with 100% CPU utilization ?
    Thanks.

    Hello,
    i have been looking at different VPN routers over the last few weeks and i was very close to buying the RV180W, but then i stumbled across many posts reffering to firmware issues, one issue is that the cpu sits at 100% useage, i just wondered if this is a bug in GUI or is the CPU actually max'd out? has anyone had any resolution into this?
    also the firmware on the emulator is a newer version than is listed on the support page, does anyone know when 1.0.3.14 will be released for download?
    when i buy a new product i like to ensure that the system is fully upto date before its put into use but i obviously dont want to add any performance issues from the ofset due to the CPU useage.
    i also have a could of questions if anyone can help
    the Ipsec VPN, will this work with the Built-in VPN client for apple devices? (New IOS7), i am unable to find a quickvpn application for apple IOS.
    is the site-to-site IPSec VPN also compatible with the Cisco Wvrs4400n router?
    thanks in advance.

Maybe you are looking for