MacBook pro, snow leopard, iPhone and Bluetooth PAN problems

Short Version:
I am having connectivity issues connecting my new MacBook Pro (MBP) to the Internet thru a Bluetooth PAN on my iPhone4. This has been working fine for a few days and then today it just stopped working responding that my iphone connection is not available, it's off, too far away or whatever. This is not the case. When I try to connect the iPhone to the MBP the iPhone is saying my MBP is not supported. I can pair the devices, but as soon as I try to connect to the Internet thru the iPhone via the MBP the connection fails.
Long Version:
I received a shiny new MacBook Pro only a few days ago and I am having Bluetooth Paired networking issues as of today, 2nd, March, 2011. The MacBook Pro is running Snow Leopard 10.6.4, and is brand spanking new, unmodified, factory defaults.
The iPhone(s) I am using are iPhone 4's with iOS 4.1
On the first day I paired the MBP with both iPhones with ease, it was so easy my grandparents could have done it. So point and click and it just worked....
The iPhones are set up in iTunes with names similar to dave1 and dave2
On the MBP I can select which device I want to connect to the Internet by going to the Bluetooth icon and connecting to whichever iPhone I have handy at the time. Since the plans are limited connectivity, I do load share between the two.
Today, for no apparent reason, I have been unable to connect to my wife's phone just getting a basic "The Bluetooth network is unavailable" message telling me the iphone is out of range, not on, etc etc etc. Not true.
No problem, I just connected to my phone instead. Occasionally I tried her phone again, but it just never worked. I eventually got her to reboot it, still no joy.
Then, a couple of hours ago, while in the middle of reading my rss feeds, my Bluetooth connection dropped out. My phone is sitting right next to the MBP. So that's not the issue. No amount of reboots of either the MBP or the iPhone have fixed this. I have unpaired and repaired the devices (on both phones) countless times. I have removed the sim card and rebooted, I have disabled and reenabled Bluetooth on both, rebooting before doing this, and after and during, I have reset network settings. Nothing I try is working here.
Pairing alone is an event, but here's an example of what's happening:
I go thru the motions, the MBP shows me a number (eg, 451234) and the number is displayed on the iPhone. They see each other. The numbers are the same. Good. I click PAIR on the iPhone and MBP and everything appears good. But then if I go to connect to the iphone on the MBP I get the out of range error.
I have made both discoverable, and tried to connect to the MBP from the iphone, and got a different error message altogether: Connection Unsuccessful - "{insert my name}'s MacBook Pro" is not supported. W-T-F? It was an hour ago? What has changed?
Then, the only option on the iPhone is to "Forget Device". ok, forget it, and start again. Same same.
Neither the iPhones nor the MBP have been upgraded or changed in anyway today, or even recently. In fact, as mentioned earlier, I was actively using the connection without any issues for a number of hours when it just stopped for no apparent reason.
Not that these matter, but I am in Thailand (live here for the time being), I'm on the TrueMove network, which offers 3G coverage in my area (Patong Beach).
This could easily have been filed under MacBook Pro, iPhone, OSX and possibly many other discussion headings, because the issue can be any or all of the OS, the MacBook Pro Bluetooth adapter, the iPhone Bluetooth, (iOS for that matter), or some other unforeseen conditions...
My head is sore from pulling my hair out. I am open to any suggestions (reasonable or otherwise!)
For further info (not that this post is long enough already, or anything, but), I thought it was interesting that the phones didn't fail at the same time, so I pulled out an old iPhone 3GS and set it up, but after pairing, the two can still not connect.
I know its not an issue with the data plan on the iPhone since I'm here surfing now without an issue, so it's not a data problem.
Open to ideas....
If you've read this far and you're ever in Phuket, give me a call... I'll shout you a beer

Ok, now I do wish I could edit....
I forgot to APPLY the network settings for the USB cable to work. Connected thru USB I can tether.
So, I kept playing, and playing some more...
I had previously unpaired everything, and gone as far as removing network devices HOWEVER...
I didn't remove the Ethernet, Firewire or Airport Network devices.
Now, I have done so. I REMOVED EVERYTHING
No pairing, no network devices.
Bluetooth was already turned off, and I rebooted.
I turned off tethering and rebooted the iphone.
I turned on bluetooth (on the MBP), I turned on tethering. I browsed for the iphone. It said I was already paired???? Ok, repair AGAIN, and THE IPHONE SHOWED MY BLUETOOTH TETHERING BLUE BAR at the top of the screen!
I opened a web page, no go... d4mn, I was close...
Opened network preferences and the created a new bluetooth PAN and voila! Internet back on the MBP. I am about to reinstall the ethernet and airport (I can live without firewire for now) and see what happens.
Basically, the link I posted two posts ago, I had already done that, but I NEEDED to remove ethernet, firewire and airport as well...
So MAYBE it's fixed, we'll see for how long. I'm not going to mark this as answered for now, because basically, it has failed for no reason, and I want to know why...
Hopefully someone can come up with something, but having to delete and reinstall all pairings and network devices (to me) is not really a solution, it's a workaround (at best).

Similar Messages

  • Hi, i forgot my macbook pro(snow leopard) password and i tried to reset it through single user mode, but whenever i type, everything comes out in CAPs instead of lower case. Each time i press the minus(-), it always comes out as an underscore(_).Pls help.

    Hi, i forgot my macbook pro(snow leopard) password and i tried to reset it through single user mode, but whenever i type, everything comes out in CAPs instead of lower case. Each time i press the minus(-), it always comes out as an underscore(_).Pls help.

    Well, you can try easing the shift key up with something thin but flexible (credit card sort of thing) but if the contacts below are stuck you may need to get it seen to by an authorised repairer.
    If you can borrow a keyboard (a PC one will probably work as long as the password is alpha-numeric with no special characters) you can at least get in to backup your HD before going for repair.

  • HT204053 have a macbook pro wife has iphone and mac mini problem the itunes account for all itunes is mine but i am unable to use icloud heres is the only sign on fcor icloud alowed i wish to have a differant one and i cant seem to get one

    how do i get my own icloud rather than share my wifes it is my itunes account

    but icloud refuses unless i use the tick***@whatever it is i dont want to use that it is her email address  understand what i say.
    You need her to sign out of your account using the button with sign out written on it.
    Then sign in using her account details. If she doesn't have an account, use the create Apple ID link in the set up window.

  • Printer says "sending data..." and doesn't print (photosmart c440 & macbook pro snow leopard)

    Hi, my photosmart C440 printer suddenly stopped working and wont print. The message says "Sending data..." forever but never prints. The printer is on but doesn't respond to what my computer says. I have a macbook pro snow leopard OS. This has never happened before, I didn't make any changes to the system. When the problem first appeared, I reinstalled the driver and was able to print once, then it stopped working. Then I installed snow leopard and it stil doesn't work.
    Thank you!
    This question was solved.
    View Solution.

    Let's reset the printing system:
    - Sys Prefs, Print & Fax
    - Right (control) click in the rectangle listing your printers and select Reset Printing System.
    WARNING - this will delete ALL of your printers!
    - Select the plus sign to re-add it. Look for the printer, select it and wait until the "Add" button becomes available. Click it.
    Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
    I am employed by HP

  • I have OSX 10.6.6 MacBook Pro (Snow Leopard) and i am trying to format my whole hard drive (back to factory settings) from the original CD. Can someone please give instructions?

    I have an OS X 10.6.6 MacBook Pro (Snow Leopard) and i am trying to format my whole hard drive (back to factory settings) from the original CD.
    Can someone please give instructions?

    Welcome to the Apple Support Communities
    To restore the MacBook Pro to factory settings:
    1. Make a backup of your files because everything will be erased.
    2. Insert the Snow Leopard disc and press the C key while your Mac is starting to start from the DVD.
    3. Go to Utilities menu > Disk Utility, select Macintosh HD on the sidebar, go to Erase tab and erase the disk.
    4. Close Disk Utility and install Mac OS X

  • Macbook Pro Snow Leopard; WiFi keeps dropping, no IP Address

    Macbook Pro Snow Leopard; WiFi keeps dropping. Issue is Macbook is not getting an IP address from the wireless routers DHCP Server. Tried all options in the forums. Reboot, changing security, PRAM reset .. nothing. Problem keeps happening. No issues on XP laptops and Nokia phones.
    Even the iPhone, iPod and iPad seems to be fine. It is just the dang gam it Macbook pro and it is driving me crazy.
    All fixes tried, changing wireless mode, security, PRAM ... only thing left is to rebuild the mac which i was hoping I can avoid somehow.
    Any ideas to fix this would be great!
    RK

    Change your router channel.  Sometimes this all you will have to do.
    System Preferences/Internet & Network/Network
    Unlock the padlock
    Locations:  Automatic
    Highlight Airport
    Click the Assist Me button
    In the popup window click the Diagnostic button.
    System Preferences/Network- Unlock padlock.  Highlight Airport.  Network Name-select your name.  Click on the Advanced button.  Airport/Preferred Networks-delete all that is not your network.
    Place a check mark next to "Remember networks this computer has joined."  Click the OK button and lock the padlock.  Restart your computer.
    http://support.apple.com/kb/TS1920 Mac OS: How to release and renew a DHCP lease
    No internet connection (wireless)
    Check to see if an extra entry is present in the DNS Tab for your wireless connection (System Preferences/Network/Airport/Advanced/DNS).
    Delete all extra entries that you find.
    Place a check mark next to "Remember networks this computer has joined."
    How to diagnose and resolve Wi-Fi slow-downs

  • MacBook Pro (snow leopard) 2006 will not restart. Getting blank screen with folder (?)

    MacBook Pro (snow leopard) 2006 has begun to turn off attached Cinema Display over the last two days. Comes back on on restart. This morning, the MacBook screen also went blank white on restart. Tried to use Snow Leopard CD to restart but it was ejected and folder with ? is only thing that displays. Will not restart. Have replaced hard drive 6 months ago. Help! What's wrong? I need this computer for work.

    hawpotr wrote:
    1. replace my current internal HD and convert it to external HD for use as secondary boot drive,
    No.  That has no advantage for you.
    leave the internal HD alone and purchase an external HD that I can clone and use as boot drive in case of emergency?
    Yes.  I use Carbon Copy Cloner to make a boot drive and as a backup (in addition to Time Machine).  CCC allows one to make incremental changes as well as creating a copy of the recovery partition.  This means that if run on a proper schedule, you data will; be well protected and the MBP can be in operation very quickly if the internal HDD should fail.
    A clone should be a 2.5", 9 mm thick SATA HDD so that it will fit inside the MBP.  It can be powered from the USB port thus not requiring an AC outlet.  In my collection of HDDs, I favor HGST and Seagate products.  I principally use OWC enclosures that allow for USB, Firewire and eSATA connections.  These are expensive but one can use a more modest one as well of one can tolerate longer data transfer times.
    Here is a link showing some available SATA HDDs that will complement your MBP:
    http://eshop.macsales.com/shop/hard-drives/2.5-Notebook/
    You can look for enclosures on the same web site.
    Ciao.

  • Why does my macbook pro, snow leopard get so hot so quickly?

    why does my macbook pro, snow leopard get so hot so quickly?
    Can someone give helpful suggestions on solving this problem?
    Thanks!
    NELLY

    Open Activity Monitor in the Utilities folder.  Select All Processes from the Processes dropdown menu.  Click twice on the CPU% column header to display in descending order.  If you find a process using a large amount of CPU time (>=70,) then select the process and click on the Quit icon in the toolbar.  Click on the Force Quit button to kill the process.  See if that helps.  Be sure to note the name of the runaway process so you can track down the cause of the problem.

  • HP Photosmart C5580 and MacBook Pro Snow Leopard wireless printer with router

    I have a macbook pro OSX operating system and a C5580 HP Photosmart printer.  I have spent hours with netgear as I did purchase a new router getting my macbook pro to print wirelessly.  Whatever the fix it is temporary and my private tech has to take control of my computer to get to work again.
    1. am I printing with bluetooth? through router? 
    2. what is happening whenever it gets out of sync and how can I fix myself?
    3. computer says "idle" but shows device connected.  I can print test page wirelessly, but not current document. Documents print when I connect with usb cable.
    I felt I should contact HP since I think it is their problem though netgear has been very helpful.  I understand that I do need USB to scan, but shouldn't have to have it to print. We have downloaded all of the most current drivers and software. 

    Tell me about your network - router brand/model, encryption type (WEP, WPA, etc) and ISP type (DSL, Cable, etc).
    If you loaded the HP software from the printer CD and unless your CD says it specifically supports 10.6 Snow Leopard, you must uninstall the software using the 'scrubber' option:
    Go to Applications/Hewlett Packard/ click on HP Uninstaller
    Click on Continue
    Highlight your device on the left pane
    Hold the Ctrl, Opt and Cmd keys and click on Uninstall
    There will be a pop up that asks if you are sure you want to uninstall ALL hp software. (At this point, if you continue, any HP printers you have installed will need to be reinstalled)
    Click Continue and let it finish
    Restart your Mac
    Now, run a Software Update.
    Next, remove and re-install the printer in System Preferences, Print & Fax.
    You do not need the software now since Snow Leopard has both print & scan drivers built-in. Scan from Preview or Image Capture apps. Scanning from the front panel of the printer does not yet work.
    Answers:
    1. No, routers don't do bluetooth.  If they are wireless routers they use wi-fi (802.11).
    2. I don't know, you have not told me enough about your symptoms or system.
    3. Same as #2.
    Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
    I am employed by HP

  • Macbook pro/snow leopard cannot see photos on iphone 4 ios7 and therefore cannot download

    Since installing a new hard drive, my macbook pro 2009 / snow leopard shows no photos on my iphone (when there are 147). I have not had a problem with downloading photos previously. Any help appreciated.
    Tim

    Have you synced the phone with iTunes on the Mac? Have you installed all system updates? iOS7 only works with later versions of iTunes & the OS.
    iPhoto should allow you to see the pictures & import them from the phone. The other option is 'Image Capture' application. It should be in the Applications folder.
    You may also need to unlock the passcode to show the device on the Mac.

  • Trouble transfering music to iPhone 5 iOS 7.0.6 from iTunes 11.1.5 on Macbook Pro Snow Leopard 10.6.8

    I recently fixed my Macbook Pro and updated the software to Snow Leopard 10.6.8.  I am having trouble syncing my iPhone with iOS 7.0.6 to my iTunes which is 11.1.5.  It gets stuck on step 4 of 4 "Waiting for changes to apply."   I've reset sync services and done a lot of research about what I can do to fix the problem to no avail.  I would appreciate any help availible.
    Thanks

    I had the same issues, reloaded itunes, updated driver, blasted everything out, etc., did everything,  short of doing a rain dance.  I finally got it to sync by clicking the box "sync only checked songs and videos".  It also allowed me to sync books, etc.  Good Luck Bwerner25.

  • Macbook pro  snow leopard 10.6.3 does not boot up. I get a grey screen and a pop up to restart computer

    Snow leopard 10.6.3 does not boot up. Macbook pro. When I push the start button I hear a chime and then the apple logo shows up and the spinnings circle. In a little while a grey screen comes on and  after that a pop up telling me to shut down and restart my computer.I have done that andit still does not work. How do I fix it.?
    richardfromfort pierce

    richardfromfortpierce,
    do you or don’t you have your MacBook Pro’s original grey installation DVDs?
    If your MacBook Pro is a 2007 model, then Mac OS X 10.6.3 was not installed onto your MacBook Pro from its grey installation DVDs, but rather from a white Snow Leopard DVD. The white Snow Leopard DVD does not have any Apple Hardware Test; to run your Apple Hardware Test, you will need the grey installation DVDs which originally came with your MacBook Pro when it was new. If you no longer have those grey discs, you can contact Apple directly and purchase a replacement pair. (They’re not available in the Apple stores.)

  • Macbook Pro, Snow Leopard , can't drag and drop?

    I have a 13" Macbook Pro and I am unable to drag and drop with my trackpad but I can with a wired mouse.  I have reinstalled Snow Leopard and checked every conceivable setting and checked the trackpad.  The trackpad will do everything else but 'drag and drop".  Any suggestions greatly appreciated.

    Sounds as if it may be a hardware issue with your trackpad - I would take it into your local Apple Store or an AASP and let them run diagnostic tests on the trackpad. If you've already reinstalled SL, that would be my suggestion.
    Good luck,
    Clinton

  • MacBook Pro, Snow Leopard and Exchange Server

    My wife is considering a MacBook Pro for her business (we have one at home). At her work they have Exchange Server. With our home MacBook Pro I have been able to connect to her Exchange server through Entourage. (however I think her Exchange server is version 4 and not 7). Anyway, we are getting mail, contacts and her calendar through Exchange but we are not getting shared calendars and I don't know how to access her files on the Exchange server. I really want her to buy a MacBook but we need to make sure that shared calendars and file sharing works. Can someone inform me about this?
    Her company is upgrading to Exchange server 7 in December and I know that Snow Leopard allows Exchange to work through Mail, Address Book and iCal. Again, I need to know if calendar sharing and file sharing can work. Thanks.

    Hello,
    Wondering if you had any luck getting this issue resolved (I have the exact same question).
    Thanks,
    -Todd / Chicago

  • Old MacBook Pro, Snow Leopard, iMovie 09 and Sony DCR-SX41 Finally Solved!

    So this has been a real trial...
    Finally got video to import in iMovie09 using the DCR-SX41.
    The issue was that the Snow Leopard upgrade trashed a critical file. I found that out here:
    http://www.squared5.com/svideo/mpeg-streamclip-mac.html
    So I purchased the file from Apple, at $21.00.
    I downloaded and installed the file, and iMovie "found" the DCR-SX41 just fine!
    If you are just coming to this camera, the trick to getting it to work with a Mac is to find the "USB Mode" or "DVD create" button. To find the button:
    *Open the viewfinder
    *Look at the body of the camera, there are two rows of three "buttons".
    *On the top row of buttons, the extreme right button looks like an arrow piercing a DVD (or CD).
    *Making sure the camera is connected to the Mac with the USB cable (on external power is helpful), *Press the "pierced DVD" button.
    * On my mac, iPhoto 09 starts up, which is annoying. So I quit iPhoto9. It sometimes takes awhile to quit!
    *Start iMovie 09
    *Open "Import from Camera" under the "File" menu
    *The Import window will open, and it will say "Import from iSight".
    *In 30 to 120 seconds, yes, a long time, a window will pop up saying "locating DCR-SX41"
    *In another 2-4 minutes, the camera will be detected, and the memory cards will be read.
    *You can now select and import videos!
    The key is waiting for iMovie 09 to detect the camera. It takes forever!
    Good Luck!
    *

    I have tried to download the MPEG STREAMCLIP, as suggested by apple, but after the download is done, when you clic on the icon on desktop, 2 folders appear. One with EXTRAS, with 2 options, About save as AVI.rtf, and another, Save as AVI.component, wich is the one I shoul finalize the instalation of the program, but, when I click on this option, a window appear a ! yellow exclamation mark over the Quicktime Player icon, with the message: 'THE MOVIE COULD NOT BE OPENED" THE SPECIFIED FILE FORK DOES NOT EXIST.".
    What else I have to do, to work?, Please, help me!!!!!

Maybe you are looking for