Manual Router CFG editing Help Needed!!

Ok so what I'm trying to do is to configure my Linksys WRT54GL by either editing the .CFG file that I can download from it or by maybe uploading a configuration file to it through tftp. I have not found an editor that will let me work with the .CFG file!
Ultimate goal: I need to put more port forwarding options in then the 10 that it will let me on the web page. Please help!!

Linksys firmware is limited to 10 port forward slots.  You can not change it.

Similar Messages

  • Router problem?/ help needed.

    Hello all,
    If your using Linux OS and in that you have two Ethernet cards like eth0,eth1 in your going two construct two types of network in LAN eg.172.16.0.0,192.168.0.0 how route these two network in an Linux OS (we put an entry's in iptables ).
    Thanks for any help.
    Regards,
    Bmora96

    You didn't specify distribution of Linux. So configuration all paths are valid for RH.
    You need to do at least three things:
    1. net.ipv4.ip_forward = 1 in /etc/sysctl.conf
    2. allow forwarding in iptables
    iptables -A FORWARD -i eth0 -o eth1 -j ACCEPT
    iptables -A FORWARD -i eth1 -o eth0 -j ACCEPT
    [pre]
    or
    [pre]
    iptables -A FORWARD -s 192.168.0/24 -d 172.16.0/24 -j ACCEPT
    iptables -A FORWARD -s 172.16.0/24 -d 192.168.0/24 -j ACCEPT
    [pre]
    3. save the current configuration:
    [pre]/etc/init.d/iptables saveor
    iptables-save > /etc/sysconfig/iptables

  • Adobe digital editions (help needed asap)

    I keep getting an error message saying adobe digital editions 2.0 has stopped working, How do i fix

    Depends why it stopped working.  You could try uninstall and reinstall.
    Unfortunately, ADE2.0/2.0.1 is a terrible program riddled with bugs,
    unless you need a feature it does not have the best solution is to install 1.7.2.
    There are lots of bugs in ADE2.0 (and 2.0.1).  Try replacing ADE2.0 with the older but more reliable v1.7.2.
    (You can have them both installed at once if you like.)
    Version 1.7.2, it is a little difficult to find, available on Adobe site for Windows and for Mac.
    http://helpx.adobe.com/digital-editions/kb/cant-install-digital-editions.html
    The forum software is sometimes corrupting the link above.  There shouldn't be a blank in 'editio ns.html'.  The following redirects to the same page: http://tinyurl.com/diged172
    Some people have found ADE trying to upgrade automatically. 
    It appears (not 100% sure) that if you install ADE2.0 as a new install (not as an upgrade) that your 1.7.2 will continue to run.
    Probably best to say no if 2.0.x installation asks if you want to migrate your library.

  • Images smaller printed then edited, help needed

    Hello everyone.
    I'm using LiveCycle Manager 8.0 on Win XP SP3
    When building a new form i got various problems with images being printed smaller then what is defined and shown in the edited and also in preview mode.
    The problem occurs with images that are being included with Image Fields.
    The problem gets even bigger if i place the images by showing them by the push of a button (script)
    Pictures will not be x/y placed and sized as defined in the layout parameter
    Here are some details about the pics:
    Larger header pic 17.7 x 8.0 cm, 300dpi
    Smaller pics bellow 17.7 x 1.6 cm, 300dpi
    Here are some screen shoots to show you how it looks.
    Any help would be great as I really tried a lot but can't find a solution.
    Designmode:
    Preview Mode
    Final PDF messed up
    PS: LiveCycle Manager also seems to run very bugy. Sometimes it crashes when changing a image parameter.

    Hi,
    OK I am trying to get to grips with what you are trying to achieve.
    The preview now shows how the form will look in Acrobat (Form / Properties / Preview / Interactive).
    In the top imageField I cannot explain why the displayed image is not as per the design view. Because it works for an image object (rev 1 in previous post), I suspect that it is a bug in the imageField object.
    There are workarounds however it would depend on the number of options (images) that the user has to select and if these images will change over time. If there are a small number of options, you could include all of the images in a series of image objects that are hidden and then change the visibility depending on what the user selects. This would be easier for the user because they would not have to browse to an image location.
    In relation to the "Geben Sie hier einen Titel ein |" header; if you are looking to change the background colour, then there is a simpler way, which i have included in rev 2.
    You can script rectangles for presence, colour, etc. The rectangle cannot contain the script, but you can include script in a button that will affect the presence and appearance (look) of the rectangle.
    Hope that helps,
    Niall

  • Expert editing help needed

    OK, so here is the situation. I filmed my friends son's christening. The ceremony was a feast for the eyes and ears. The audio track is beautiful, and a complete record of the ceremony.
    I want to preserve the audio track and much of the video, while I overlay video clips (without their audio), and stills in places where my camera faltered.
    My problem is, how do I put video/pics over the audio, and cut back to the video of the ceremony while maintaining the synch between the audio/video of the original footage?
    I only know how to trim/split/crop clips, and it seems like it would be near impossible to get the audio and video to match-up every time I splice in new footage.
    I am extracting the audio from the original footage as we speak.
    Thanks in advance
    -Tim

    Under the Advanced menu, use "paste over at playhead" instead of manually cropping/splitting/pasting. Prior to using this command, you will need to copy your clip into memory (command-c).
    This command pastes your clip into your movie, while not affecting the audio track. The movie will get automatically cut the same exact length as the clip you are pasting.

  • Simple Narration Editing Help Needed

    Hello,
    I am brand new to audio editing and SB. I have recorded a narration. There was a little bit of background noise and the peak levels were a little too high (going into the red a little too often). I selected a piece of the background recording where no narration exists and used the "Capture Noise Print" in the Clean Up Audi0 - Noise panel to get rid of the background noise. Then I "Equalized Volume Level" to take care of the peaking problem. However, now the voice is a little on the tinny side. Can anyone suggest how I can get rid of that tinny sound and bring back the richness? Or perhaps a tutorial?
    Any suggestion on how to record with proper levels would be helpful as well.
    Thanks,
    Mike

    I have the same problem.
    Did you ever figure this out?
    Using the Effect Fix:Remove Hiss seemed to work better, but there is still a significant amount of background noise when no one is talking.
    It did seem to help to set the Noise -> Reduction value down to 30 or so using the Preview and Green switch to hear the difference.
    I'm still looking for the best workflow to cleanup a group discussion setting and would appreciate anyone else's experience.

  • Apple TV set up in NZ as US or UK router...help needed please

    Hi, we were lucky to be gifted and Apple TV but I am struggling to set it up so that we can make use of it here in NZ. So I have followed the geekzone advice and subscribed to unblock US and I have subscribed to Netflix but what a poor choice. So I followed the DNS router numbers advice on geek zone....but can't see primary and secondary DNS distinctions....I get one chance to put numbers in, so which numbers do I go with, primary or secondary??? The rest of the instructions don't make sense either with the screens I get.
    We don't want much.... A news channel, a decent movie channel to save us going to the DVD store ( very happy to subscribe to this) and maybe a decent channel for uk comedies and dramas. Netflix ipseems to only have old movies??
    So here I am, in NZ with a lovely Apple TV and sooooo frustrated. Any help or idea warmly received. Thanks guys all help very much appreciated.
    We have an iPad 4s and an iPhone but that's old only a 3G if that helps with our troubles
    Thank you heaps in anticipation of a solution ;) :)

    Matty, using techniques that you describe to access  content outside of your country would probably fall foul of Apple's forum T&Cs.  (I've not used the technique you descibe and even if anyone has experience doing so, describing the process might cause forum moderators to pull the thread).
    Unfortunately the US does get the pick of the crop, though I suspect that's more to do with stubborn movie companies and regional negotiation for rights than Apple's problem as it would be simpler for them tohave harmony across the globe in terms of what they offer to each country.
    Can you not use iTunes Store for movie rentals in NZ?  That should have a pretty up to date selection though again regional licensing deals mean soem providers may have exclusive options (eg Game of Thrones seems tied to Sky in UK, so not eve a 3 year old show in iTunes).
    Ac

  • Real Trouble Setting Up New WRT160N Router...Help Needed

    Current configuration is as follows:
    Motorola DSL modem paired with a Netgear Wireless-G router. Works fine, I have a connection.
    There is a problem, though, accessing the router's browser interface. This has happened since I reformatted my PC from Vista back to XP Pro SP3. My computer came with Vista. The drivers for my "1394 Network Interface" are generic, and I am afraid that although the blinking green light fuctions when an ethernet cable is connected (router to PC), somehow something is not right. The router access address is not working (192.168.2.1). Perhaps I am entering it wrong? Do I need a port number? I run my PC wirelessly to the internet via a Netgear wireless PCI card that I have installed. It works fine.
    My objective is to set up/configure my new Linksys/Cisco Wireless-N router (WRT160N). After I insert the included CD to begin the setup process, the setup process itself fails due to an error. The setup program tells me that it is unable to detect an ethernet port, and to enable it if it is disabled. Well, I do have one, and it has a driver, albeit probably not the correct one. But it is there, and the setup program won't let me continue because it can't see it. Here is where the fun begins.
    I have already tried reinstalling the ethernet driver. I downloaded a PC information program like CPU-Z and it revealed my ethernet connector's manufacturer whose name escapes me at the moment. Since the PC came with Vista, I cannot readily find any XP drivers that will suit it. In a desperate yet feeble attempt I downloaded and paid for a driver-updater program, to no avail. My motherboard is an ASUS NodusM3. I have also tried to connect the WRT160N to my PC to check for any viable communication. None.
    So in a nutshell I can't get the router's setup program to believe that I have a viable ethernet connection, in which case I may not because I can't get the PC to run off the router via an ethernet cable. I can't even access  the router via the browser. In this case will I need new drivers? If so, where do I find them? How can this issue be resolved. It really sounds like a driver issue to me.

    The router uses no drivers.  Connect at 192.168.1.1 not .2.1.  Reset router by pressing reset button for 30 seconds.  Release and wait 10 seconds, and power cycle.  Connect to the correct IP of 192.168.1.1. via cable.

  • Using AXs with a Gateway Router...help needed

    For years my wife and I lived in a home which ran an AirPort Extreme for all our internet and music needs. We've recently moved into a new home which already had a DSL/Gateway wireless router installed (as part of AT&T's HomeZone packagge). After giving serious thought to my desire to have a new wireless sound system for my new home, I bought the following at the Apple store:
    - Two AirPort Express;
    - A Bose Companion 3 Series II powered speaker system; and,
    - An iPod HiFi.
    I've hooked both the Boze speaker & HiFi systems up to their own AirPort Express, and they sound great when I run my iTunes through my wireless system for +that particular+ AirPort.
    The problem is is that I can't seem to get both sound systems to play simultaneously, nor can I connect to my internet (Gateway) and run either (or both) of these speakers.
    Any hints as to HOW I can get music to both AirPorts while still being able to surf the net on my Gateway router? Is there a way to bridge both AXs to the Gateway?
    I know...I'm a luuddite. Thanks in advance for any suggestions.

    Hello mrviognier. Welcome to the Apple Discussions!
    Any hints as to HOW I can get music to both AirPorts while still being able to surf the net on my Gateway router?
    Yes, you just need to configure the AirPort Express Base Stations (AX) in "client mode."
    AirPort Express Base Station (AX) - Client Mode Setup
    o Plug the AX into a power outlet.
    o On your computer, join the wireless network created by AX.
    o Open AirPort Admin Utility. (Mac users: Find it in /Applications/Utilities/. Windows users: On the Start menu, point to All Programs and click AirPort.)
    o After AirPort Admin Utility opens, the name of your AX appears in the list. Select it, then click Configure.
    o Enter the administrator password if prompted.
    o Click the AirPort tab.
    o Enter a name for your AX in the Name field. (This name is how it will appear in AirPort Admin Utility; it may be different from the AirTunes remote speaker name. (Note that AirPort Setup Assistant does not allow you to differentiate these names, but AirPort Admin Utility does.)
    o If your AX does not already have an administrator password, click the Change Password button to enter one. This password can be different from any network password, and is used for just changing settings on AX.
    o In the same pane, under the AirPort Network heading, change the Wireless Mode from "Create a Wireless Network (Home Router)" to "Join an Existing Wireless Network (Wireless Client)."
    o Type the name of the wireless network you want to join in the Network Name field. (Note: If you're using AirPort Admin Utility in Mac OS X, you may be able to choose the network from a pop-up menu. This is the name (or SSID) of your current wireless network with the Trendnet router.)
    o If the wireless network is password protected, you will need to enter the password. (Mac users: Click Security Options, choose the level of password encryption from the Wireless Security pop-up menu, then enter the password. When finished, click OK. Windows users: Click Wireless Security, choose the level of password encryption from the Wireless Security menu, then click "Set WEP Password" to enter the password. When finished, click OK.)
    o Click the Music tab to enter the name that will appear in iTunes as your AirTunes remote speakers. You can also enter a password to prevent others from streaming music to your speakers.
    o Finally, click Update to send your new settings to AX.
    Once the AX has had a minute or so to restart, it should join the existing wireless network, as indicated by its status light turning solid green.

  • I just started up with my IPod, I download music to my library and I accidently changed the artists name in an entire category.  I can't figure out how to undo it. I read the edit help stuff but I can't select the item I need to edit

    I just started using my IPod and I downloaded my library.  I accidently changed the artist names for an entire genre category and I can't undo it.  I read all the edit help stuff and I either can't select items to edit or I'm an idiot and I can't figure it out.  I keep trying and I get a pop up that asks me if I want to change multiple items.

    Did you ever resolve the iCloud problem.I am in the same position and its driving me mad!!! If you have a link to an solution I would appreciate it.

  • ONKYO TX-SR805 Set-up Menu HELP Needed

    This is a LONG post, but I would appreciate if you would read it and respond to it.  The settings That are setup might not be the CORRECT settings.  If you think a different setting should be made, please let me know.
    Also right now I only have 2 front speakers (NHT VT-1A), 1 middle( NHT VT-1C), and a NHT SW12 Subwoofer.  I will be hooking up 2 or 4 more speakers for the REAR.
    Here are the settings on my TX-SR805 receiver on the set-up menu.  I could use some help to see if they need set to something else.
    2.2 Speaker Config
          Subwoofer       yes
          Front            70Hz
          Center          90Hz
    LPF of LFE        80Hz THX
    2.6 THX Audio Setup
           THX subwoofer  YES   I don't know if mine is or not
           BGC                    OFF  Not sure what this BGC means
    3. AUDIO ADJUST
    3.1  Tone Control
           Front    Bass      -1dB
                        Treble   +1dB
          Center  Base      +2dB
                        Treble   +7db
         Subwoofer Base  +7
    3.2 DIRECT
          Delay Enable
          DSD                NO   Not sure what DSD is 
    3.3 MULTIPLEX/MONO
          Multiplex
          Input CH       Main/Sub
          Mono
          Input CH         L+R
          Output Speaker  L/R
    3.4 PLIIx/Neo:6
            PLIIx Music   (2ch input)
            Panorama        ON
            Dimension       +1
            Center Width    3
    Neo: 6 Music
            Center Image   5
    3.5 DOLBY EX
            Dolby EX        AUTO
    3.6 THEATER-DIMENSIONAL
            Listening Angle   Narrow
    3.7 LFE LEVEL
            Dolby Digital      -10dB
            DTS                     -10dB
            Multich PCM      -10dB
            Dolby True HD   -10dB
            DTS-HD Master Audio  -10dB
            DSD                     -10dB
    4. SOURCE SETUP
           CABLE/SAT
    4.1  INTELLIVOLUME     +4Db
       .2 A/V SYNC            0 msec
       .3  NAME EDIT         Blank
    5.   LISTENING MODE PRESET
    5.1 DVD
           Analog/PCM      NOT SURE WHAT TO SET HERE
           Dolby Digital      NOT SURE WHAT TO PUT HERE
           NOT SURE WHAT TO PUT FOR ANY OF THESE LISTENING MODE PRESET
    5.8 TUNER (ANALOG)      Neural THX 5.1 is set on mine. Is this correct?
             CD                           ?
    6.  MISCELLANEOUS
    6. 1  VOLUME SETUP
              Volume Display              Relative
               Muting Level               -40dB
               Maximum Volume       +10dB
               Power on Volume        -22dB
               Headphone Level        +2dB
    6.2  OSD SETUP
               Immediate Display       OFF
               Monitor Type              16:9
               Display Position           TOP
    7.  HARDWARE SETUP
    7.4   ANALOG MULTICH
               Subwoofer Input Sensitivity    0
    7.5   HDMI
            ALL under here are     ENABLE
    Solved!
    Go to Solution.

    I gave you some answers in your original post. I wish you didn't start a new one. Here is what I posted.
    Re: ONKYO TX-SR805 Set-up HELP Needed[ New ]
    Options
    Mark as New
    Bookmark
    Subscribe
    Subscribe to RSS Feed
    Highlight
    Print
    Email to a Friend
    Report Inappropriate Content
    01-21-2010 08:24 AM
    Unfortunately this is very difficult because the top half of your post, your really the only one that can answer what the setup should be.  The adjustments are made based on the acoustics of your room and how everything sounds noone can really give you info on it because every house, and room has different acoustics.  The walls, insulation, carpet or bare floors, basement or main floor are just some examples of what can make a difference in sound reproduction.   By the way NHT (Now Hear This) are excellent speakers.  For bass and treble, the music I listen too requires a high treble content so I usually have it at 7 out of 10 but my bass is at 4 out of 10.   The sub base should be fine where it is.
    Did your receiver come with an Audessy mic for calibration.  I would use that for a basic setup and go from there I am not sure if on your unit it will do frequecy but I think it did.
    Your volume settings look fine again personal preference there is right or wrong.
    For you listening mode Preset  you should have an auto setting I am at work so it may take a coule of hours for me to get back to you as I have to go through your manual and see what you would set it up with so please bare with me. I will list the info as I read it so it may not be in the order you have it.
    I will have to make a second post since I can't go back and edit this one.

  • Troubleshoting help needed:  My iMac keeps crashing and restarting with a report detail: "spinlock application timed out"  What can I do to fix this?timed out"

    Troubleshooting help needed:  My iMac keeps crashing and restarting with a notice: "Spinlock application timed out"  What can I do?

    Launch the Console application in any of the following ways:
    ☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
    ☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
    ☞ Open LaunchPad. Click Utilities, then Console in the page that opens.
    Select the most recent panic log under System Diagnostic Reports. Post the contents — the text, please, not a screenshot. In the interest of privacy, I suggest you edit out the “Anonymous UUID,” a long string of letters, numbers, and dashes in the header and body of the report, if it’s present (it may not be.) Please don't post shutdownStall, spin, or hang reports.

  • Urgent Help Needed for WVC210 camera setup :)

    Please help!  I am trying to set up a Cisco WVC210 surveilance camera at one of the stores owned by the company I work for.  Its a small business and I am the closest they have to an I.T person !! I have plenty of experience with software but not much on networking so need some idiot proof guidance !   The "administrative guide" is not worth the paper it is printed on!!
    The store has a fixed IP address of 212.9.##.### I connected the camera using ethernet cable.  Set the camera up using the software for the camera, with static ip address of 192.168.0.23.  Set the SSID of the camera to that of the router (a Netgear one).  It worked fine.  I went to unplug so I could have it wireless and NOTHING !!  It did work one time (no idea what i did differently!) but it would not work over the internet which is what we need it to do!  I need the whole thing password protected too! 
    Is there ANYONE who can help me please???  I am at the point of running away from my work and never returning !!!! :s
    Thank you

    Hi Jodie,
    Thank you for posting. In order to make the camera connect wirelessly, first set up the wireless settings in the camera to match the router. I usually open the router configuration page and copy and paste the SSID and Security Passphrase to the camera to avoid error. The next step is to unplug the ethernet cable and power cord from the camera. Then plug only the power back in and the camera should connect wirelessly.
    For remote access to the camera you will need to forward port 80 to the LAN IP address of the camera. (192.168.0.23) This is done in the router. If you need help with port forwarding, you can search the web or call Netgear for assistance.
    If you continue to need assistance with the camera, the fastest and easiest way to get assistance is to call Cisco Small Business Support. www.cisco.com/go/sbsc
    Please go to www.cisco.com and click on "Register" in the upper right to create a user ID. This will allow our engineers to create a case for you.

  • My WRT54G2 will Not Work HELP NEEDED !! PLease Help

    Hey i Have a WRT54G2 and it has worked Flawlessly for about a Year... One Day i Wake u To No Connection coming From my Linksys ..... on the Wirless Connections Pop up there is a Message saying  " Information Sent over this network might be visable to others" I Have Tried Everything and Anything to Figure Out or Fix the Problem But NOthing i Do Works ... I am Really Out of Options ,,,,, Someone PLeaseeeee HElllllp Meeeee !!!!1 Aaaahhhhhhhhhhhhhh 

    In this case try to change the power socket. Try to do 30/30/30 hard reset. The following procedure will clear out the NVRAM and set Router back to default values:
    ~~ With the unit powered on, press and hold the reset button on back of unit for 30 seconds
    ~~ Without releasing the reset button, unplug the unit and hold reset for another 30 seconds
    ~~ Plug the unit back in STILL holding the reset button a final 30 seconds....
    Then make the physical connectivity. Here are the steps for the physical connectivity for the router:
    The router’s power adapter needs to be plugged to your router and into an available power outlet.
    If using a wired connection, the first Ethernet cable needs to be plugged to the computer’s LAN port into any of the router’s blue numbered Ethernet ports.
    The second Ethernet cable should be plugged to the modem’s Internet port and the other end into the router’s yellow Internet port.
    Ensure that you have no firewall enabled that may prevent the router from being detected.
    Then make the manual settings according to the ISP setup. Here is the link for setting up a Linksys router with Cable Internet service:
    http://www6.nohold.net/Cisco2/ukp.aspx?vw=1&docid=0ff4c94586a345d082828ec2161aaecf_3686.xml&pid=80&r...
    Here is the link for setting up a Linksys router with DSL Internet service: http://www6.nohold.net/Cisco2/ukp.aspx?vw=1&docid=20ee1457387f40178cd5f41d4b585db4_3687.xml&pid=80&r...

  • Help needed on installation of Oracle 9i on Sun Solaris 8

    Hey,
    Help needed on installation of Oracle 9i EE on Sun Solaris 8. The problem I met was: we followed the installation guide from the documentation. And we selected the choice "install software only". After it was done successfully, we run Database Configuration Assistant utility to create a database instance. But finally it always tried to create the instance at the root directory ( / ) which doesn't have enough space and then failed. The case was that we have set the enviroment parameters: $ORACLE_BASE = /export/mydata, $ORACLE_HOME = /export/apps/oracle9i. That means it should be installed at /export/mydata, but it didn't. Any help or advice are welcome. Thanks.
    Simon

    I have downloaded Oracle 11G R2 version from Windows and extracted it in Windows and copied it into DVD after extraction in two folders. Now I am mounting that DVD in Solaris 10 installed in my VMware . I made a new directory named as 'installation ' under /export/home/oracle and copied the folders from DVD to 'installation' folder. Now I am entering installation folder and try to do ./runInstaller as 'oracle ' user and getting the error mentioned before.
    Edited by: 916438 on Mar 31, 2012 5:55 PM

Maybe you are looking for