Materials not shown in MD4C

hi there SAP Gurus,
i have a problem with MD4C, where not all the materials in the BOM is not shown in the MD4C report,
wheni check with md04, the material is there, but when i check with md4c the material is not shown there,
why the md4c not showing the material?
thank you.
vasan

Hi,
In MD4C you cannot find consumption based planning materials(MRP type- Reorder related) even though they are present in BOM.
Regards,
Krishna Mohan

Similar Messages

  • Navigation Attribut is not shown in two rows in the Query

    Hello,
    we are using a multiprovider with the infoobject 0material. In the multiprovider we use a navigation attribut MH_PR_ST of 0material.
    Normally, the query rows should show the material number and the corresponding attribut MH_PR_ST, but in some materials in the multiprovider exist some rows where the attribute is shown correctly from the master data table and in some rows the attribute is not shown.
    Therefore in the query two rows are shown:
    Material No. MH_PR_ST Key Figure
    4711           A                    10
    4711           #                       5
    Sum                                  15
    With all other navigation attributs there is only 1 row.
    Do you have any good ideas?
    Thank you very much + best regards,
    Ilona

    Hi,
    Assuming the second row comes from one of your basic cube; since it looks that 0MATERIAL is populated (it is coorectly identified), ensure that the identification of the nav 0MATERIAL__MH_PR_ST is done properly in your multiprovider.
    hope this helps...
    Olivier.

  • Material is not shown in MD04.

    Hi Friends,
    We have created a Sales order for some materials. All the materials are subjected to MRP.  In mateial master  We maintian all Except MRP group. Also we maintain the Requirement type etc with respect to the Mateial Type in configuration.  In our case when we created the Sales order some of material are picking the requirement and same was shown in MD04 also in availbility check we can able to check the reqirement  but some of the msaterials no requirement generated in availibility and not shown in MD04.  All the materails are belongs to material Type FERT. Let me know some materials are not Picking the requirement and not shown in MD04.
    When we maintain the MRP Group  the materials were picking the requirement in availbility and alos shown in MD04.
    Will anone explain the difference between the both setup like Picking requirement with respect to Material Type and Picking Requirement with respective to MRP group etc. aslo  when and where we can user those things
    Regards
    Palani

    Requirements of sales orders are transferred to MD04 based on the item category.
    In SPRO/IMG:
    Sales and Distribution --> Basic Functions --> Availability Check and Transfer of Requirements --> Determination of Requirement Types Using Transaction
    In here, you set a requirement type for each item category.  Without a setting here, the requirements do not display in MD04.
    Hope this helps.
    Gina

  • Direct Material Not Shown in Search Products/Services

    Hi ,
    We are implementing Classic Scenario on SRM5.0. We replicated materials.The materials are shown in COMMPR01 with out Product Descriptions.When try to search for Materials under BBPSC02> Internal Goods/Services > Find Product, i don't see any materials.Product GUID returns no values.But Search by Description of Product Id returns Materials.But when select the material returns Message"No values for this Selection".
    Any Suggessions please?
    Thanks and Regads,
    Sudhakar.

    Hi Yann,
    Yes. Apparently the issue belong to Data .When i create material Manually in R/3 and Replicate ,i am able to see.But not the converted data.
    So at this point i would seek help..can some one tell me what is criteria for the Direct material to be shown in internal goods/Services area..i mean can i replicate all material types like Finished goods,Semi finished ,Valuation classes, with or without Plant Specific material indicator etc.I have purchasing and accounting views right on all materials.
    Thanks and Regards,
    Sudhakar

  • Not shown batch no in receipt from production

    Hi
    Experts
    we issued the materials to production with batch numbers. but that production was rejected so we have to receipt the materials from that production order only in that time one item batch number was not shown when we take the receipt from production
    Regards
    Venkat.

    Hi Venkat,
    Show the Batch Number Transaction Report Ware house wise with Particular Item No. you have a issue.
    Check Issue Ware house material are outgoing with particular Batch Number or not.
    For that need to post this issue to SAP with this result and reference of note no.1250867 (Inconsistency of Items Managed by Batches / Serial Numbers )
    =========
    Solution
    =========
    In order to fix your database, please, log a support message via the Service Marketplace referring to this note including all relevant information and results of the attached queries.
    Thanks,
    Srujal Patel

  • In MI31 not shown all batches

    Hi,
    I have run MB52 with batch wise and i got list of stocks with batches then i want to comparision in physical inventory with batches so i run MI31 and comparision material with batches but all materials are not shown in MI31.
    please guide me or missing any config we need this details.
    Thanks
    'Shital

    Hi
    There is no config missing. MI31 takes the stock of those materials, for which previously no Physical Inventory has taken place.
    Just check those materials.
    Reg
    Manoj

  • Some fonts are not shown correctly in LabVIEW 2012

    I found a bug related with fonts in LabVIEW2012 f3 KR.
    - When I select NI7SEG in font selection dialog, right font is not shown in the example box.
    - Draw text at point.vi shows same problem for some fonts while other fonts are working.
    I reported it to Korean NI. As far as I know, this was not reported in previous versions and I couldn't find any related documents in Google. 
    So, here I would like to know whether it is related with only Korean version. Please let me know if English version is OK. 
    * OS: Windows 7 32bit KR

    Just now, I installed LabVIEW 2012 f3 (32-bit, English) and checked for the issue. But the font(NI7SEG) was not shown properly in VI either.
    - Both of Korea and English version of LabVIEW 2012 on Win 7 Korea OS shows wrong results. It is same on 64-bit OS.
    - LabVIEW 2010 but on same PC shows correct fonts.
    Is there a limit of number of fonts in LabVIEW? There are more than 100 fonts are shown in the "Selection Font" dialog and I can divide them into 3 groups by sequential order. I find that all fonts in the 3rd group are not applied correctly.
    (1st group)
    Arial Unicode MS...
    Bookshelf Symbol 3....
    Windings 3
    (2nd group)
    @Arial Unicode MS...
    @Terminal
    (3rd group)
    Arial...
    Consolas...
    Courier...  
    Licida Console... 
    NI7SEG...
    Verdana

  • IPC/VC: Knowledgebase/KB of ECC is not shown in CRM

    Hi,
    we would like to use the Variant Configuration in CRM.
    Today we are using already the IPC in a standalone environment with an external system (IPC 5.0, the external system is using the IPC in the Java environment of ERP). From the same ECC System we would like to download now the knowledge bases to reuse them in CRM 7.0. All knowledge bases and runtime environments are already available. When I download the object SCE (with certain filters), I can see all those entries in table COMM_CFGKB in CRM.
    Anyhow, when checking the material in CRM (e.g. commpr01 or WebUI), no knowledge base is shown!
    The table COMM_CFGKB has exactly the same entries as ECC (Active = T, KB Usage 10, KBOBJNAME and Version filled etc.), but anyhow it is not shown at all in CRM. As these knowledge bases are very huge, I have tested also a very small and easy one. This one is getting downloaded the same way and has the same entries in table COMM_CFGKB and it is also visible in commpr01.
    So my assumption is that the other KBs are not 100% correct. When checking them in ECC (cu36) I get many warnings and errors. Anyhow, they were downloaded to CRM (but won`t be shown). Business says that these warnings/errors are OK and that the external system which uses the IPC in ECC is not having any problems.
    Question: is there any chance of using a KB in CRM which has warning/errors when it was generated in ECC?
    Is there any chance of manipulating the KB before it gets imported into CRM. I have found Note 1044682 which explains a BADI.
    Which tables/fields do we have to manipulate so we are able to use the KB in CRM. 
    As mentioned: business is aware of those errors and excepts that there might be a crash in the IPC for certain combinations.
    Thx
    Guido

    Hi Christophe,
    OK, I think I understand your suggestion: you use the same IPC with your CRM as well as with the ECC system. So in CRM you just maintain the URL and a user in XCM to the "same" IPC. You mentioned that we need to download anyway the SCE. This is somehow logical as this is the base connected to CRM, but what is not clear to me is the fact, that if the SCE KB is used via ECC all SAP R/3 fields are available (like VBTYPE of the sales order where you have values like B or C). In CRM we use the same SCE KB but here these fields are not availble as the sales order transaction customizing in CRM does not contain such a field.  Where is the logical link between the values which are available in IPC and the SCE?
    Thx
    Guido

  • Voice memos sync not shown in iTunes

    I am trying to sync my voice memos to iTunes a couple of times. They are not shown. I haven't updated my iPhone 5s to the latest software yet. It's still running iOS 7; my iTunes was updated though. Does anyone have a solution for this?
    Thank you!!!

    You need to open iTunes on your computer. Then select music library from the left-hand. Then in the search window on the top right of the screen type in voice memo . The voice memo should now appear in the list is available music in the middle of the iTunes screen

  • Yosemite 10.10.1: Finder/CIFS mount problem: wrong folder count/folders not shown @samba shares

    Hello to all,
    we have several MacBook Pro (15" MBP Retina 2012/13"MBP Retina 2014) running. After upgrading to Yosemite 10.10.1 we had one nightmare after the other.
    Most problems could be solved with 3rd party software upgrades but there are several problems with the operating system itselve which can not really  be called a professional productive system at the moment...
    Ok., one thing after the other...here is one of our biggest problems:
    After upgrading from Mavericks or Mountain Lion to Yosemite 10.10.1 the CIFS/SMB mounts to our samba 3.x servers, running on Ubuntu Linux LTS 12.04 makes trouble. We could mount the server shares but after browsing with the Finder the beach ball occures and the Finder hangs forever. Sometimes we could not refresh the Finder, killing the process ended in a complete hang-up of the system which ended in a switch off death blow. This is not amusing because we have 30Tb of customer data there, which has to be worked out.
    We heard about the SMB3 protocol which will be used per default in Yosemite and so we decided after some testings to upgrate our Ubuntu servers to the latest LSF 14.04. release with samba 4.1.6 installed. There was no message from Apple for this SMB protocol release upgrade, never heard something related to Yosemite (Why?).
    Ok, after these server upgrades and disabling most of the Spotlight functions the performance to the CIFS shares was a little bit better as before but now we have another problem with the Finder...if you browse to the shares there are folders missing which have lots of files in it. For example there is a folder with 60 subfolders and 3562 files on the first level in it, the Finder shows 220 files and 15 folders. The Terminal shows a different count with "find . -maxdepth 1 -type d | wc -l" or "find . -maxdepth 1 -type f | wc -l" but there is also a difference to the original file and folder count. It doesn`t matter if the clients are connected via WiFi or Gigabit Ethernet. We have no access problems. We have the same behavior if we set the files and folders to 0777 permissions on the servers. The deletion of the preferences files of the users on the MacBooks does not solve the problem. If we use the "Go To Folder" option and type the path to a folder which is not shown in the Finder you get an result or not. But it is also possible that the result is not correct and there are also still files or subfolders missing.
    In my opinion this is a timeout problem and a "special SMB3 protocol interpretation" which is buggy. We have one hint found in /var/log/system.log:
    "Jan 23 14:35:49 wsosx33.clients.getcom.de KernelEventAgent[69]: tid 54485244 type 'smbfs', mounted on '/Volumes/customersdata2015', from '//x144067:@srvlxp013.servers.getcom.de/customersdata2015', not responding"
    We had no problems with Mavericks at all, we still have no problems with Windows 7 Pro/Ultimate, Windows 2008R2 (native or virtual) or Linux Mint 17/17.1 clients, neither with samba 3.x nor with our actual environment and different newer samba releases.
    We believe that this is a big bug in Yosemite, but we cannot go back to Mavericks because of incompatible TimeCapsule backups. Our workarround at the moment is that we have installed Linux Mint on our MacBooks to get 80% of our daily jobs done, rest has to be done with Windows 7 installed over virtualbox @Linux.
    We have no clue at the moment how to solve this problem, the samba logs do not give any hint. The access from other operating systems is perfect and very fast, but not with Yosemite. We checked different tips found in the internet but nothing helped.
    Does anybody has another idea to get Yosemite working or should we keep Linux Mint until Apple will provide a CIFS/SMB patch and going on with our workaround solution, which is productive at the moment ??? Our staff is not amused and wants one solution and not this workaround with two operating system. We have to decide wether we wait until Apple will get this fixed or we have to switch to Microsoft Windows (which is a No Go for me, but I will not be asked...).
    Thanks in advance
    C.

    Hi William,
    thank you for your response.
    As you can read in my post I talked about CIFS/SMB.
    It makes no difference if we mount the share over CIFS or SMB.
    Folders with lots of files will not be shown even if we use SMB3 or an older protocol.
    As mentioned I believe this is a timeout problem.
    Does anybody know how the CIFS/SMB timeout setting in Yosemite could be changed?
    Kind regards
    C.

  • In my Apple Macbook Air, most of the USB Flash/Thumb Drives are not shown in the Finder Window. Only a few Brands of USB /Flash Thumb Drives are shown or compatible or shown in the Finder. How do I use any Flash/Thumb Drive with my Apple MacAir?

    In my Apple Macbook Air, most of the USB Flash/Thumb Drives are not shown in the Finder Window. Only a few Brands of USB /Flash Thumb Drives are shown or compatible or shown in the Finder. How do I use any Flash/Thumb Drive with my Apple MacAir?

    Yes, junker thumb drives pour like rain in the market.  
    Which makes are working on your Air, and which arent?
    Stick to Sandisk and a couple of other reliable mfg. of memory sticks

  • Reporting tab is not shown in the console

    hi everyone
    the reporting tab is not shown in the service manager console, the topology i am using is 2 servers [one for DW and the other for management server] both servers have their SQL server installed on each one, could you please tell me how i can start to get
    this working or the steps i have to follow ?? isn't supposed to be working out of the box ? i have checked reporting services and they are running

    Probably your report server is not pointing to the DWDATAMART database, try login to:
    http://YourDWDatabase/Reports/Pages/Folder.aspx?ItemPath=%2fSystemCenter%2fServiceManager&ViewMode=List
    click on DWDATAMART Connection, under connection string, do you see your DWDATAMART DB name and server name?
    Antoine AL Ibry

  • Text in PO(text tab in header & item) is not shown in the Print Preview

    Hi Guys,
                I face a problem in ME23N.Text maintained in Purchase Orders (text tab in header & item)  is not shown in the Print Preview.
                Can you guys help.Do I need to write a subroutine pool for this.
                <<text removed by moderator>>
    Regards,
    Rajiv
    Edited by: Matt on Nov 12, 2008 1:20 PM

    Hi ,
    Use bapi bapi_po_getdetail .
    CALL FUNCTION 'BAPI_PO_GETDETAIL'
        EXPORTING
          purchaseorder   = is_ekko-ebeln
          item_texts      = c_x
          header_texts    = c_x
        TABLES
          po_header_texts = it_header_text
          po_item_texts   = it_item_text.
    Regards
    Neetesh

  • Approved and published items are not shown in the catalog search

    Hello all,
    We are implementing SRM 4.0 SSP scenario .
    To support shopping of EBP we are also implementing CCM 2.0 as an add on.
    Please note CCM and EBP are on same client and CAT & CSE are also on the same client.
    No XI is involved. The catalog scheme was uploaded as CSV 2.0. The items for the catalog was created manually in CAT.
    Although the item has the status "approved" and the procurement catalog which is also the master catalog was published successfully the item is not shown after searching by CSE in EBP. Also the categories of the scheme are not shown in the catalog search.
    Do i have to approve the categories too and if yes can you  explain me how to do this?
    I think you see that I'm a newbie at srm and ccm and this problem is probably no real problem but I have not found any similar topics in the forum. So please can you help.
    Thanks a lot for your help.
    Best regards,
    Bernd

    Bernd: the reason I asked about views is that you don't have any error messages. This might indicate that (a) you have no items in the view, or (b) there's something wrong with view-role-user assignment.
    To check for (a), please go to the published procurement catalog, and go to Views tab. Check that your View is Active. Click on your View ID link to display view details. You should see a list of characteristics assigned to your view in Assign Characteristics sub-tab (the list should not be blank!). Go to Assign Items sub-tab. Navigate in your schema to find items that are supposed to be assigned to your view. You should see "Yes" in the "Assigned" column for those products. If you don't, then you simply don't have any items in your view.
    Another thing I'd like you to check: when the user calls your procurement catalog for search, do you see the name of the catalog displayed just below the drop-down "Select Categories Hierarchically"?
    Cheers,
    Serguei

  • I AM STUCK WITH MOZILLA FIREFOX / NOT SHOWN ON MY LAPTOP SCREEN / USING HUGE AMOUNT OF RAM IN GENERAL - CAN YOU HELP????

    Hi,
    I have copied these problem on you site, as I could explain better then what they did, wich my problem remain the same as they have. And part me explaining what is really happen to my Laptop.
    ''Mozilla/Firefox 4 will not SHOW on my computer SCREEN.
    Firefox won't load onto my computer. I have Windows 7, and each time I try to run the program to install it, it tells me I have another version still waiting to be installed that requires my computer to reboot. When I check "yes" to reboot, my computer reboots but still no Firefox. When I try to uninstall the the old Mozilla program from my Control Panels, there is no Mozilla files or programs listed not in my list of programs but when I go directly to the Windows File on the C: Drive, there's a Mozilla program file there. WHen I go into that file check, I attempt to open the uninstall program. I get an error message that says something to the effect of: "the version Mozilla on this computer is not compatable with my OS." Something about it being and 86bit program. My Firefox 3.6 worked fine 2 days ago. What's wrong??? ''
    '''Firefox 4 using huge amounts of RAM on sites with Java scripts
    I have been observing Firefox using huge amount of RAM when I am on sites that use Java Scripts to rotate images. I have tried a couple of different sites and have monitored the RAM usage. With Java script enabled Firefox 4 continues to grow its RAM usage by about 10MB a minute. I have had the usage hit as high as 1.5GB. As a comparison I have monitored the same sites in Internet explorer and have not seen the same issue. - Just to eliminate a site issue.
    Turning off Java Script solves the issue and eventually frees the RAM.
    I am using XP Pro, 3 GB RAM. '''''
    My experince with Mozilla Firefox:
    Here what really happen when I install the Mozilla Firebox on my La[top you can see the file is there but when I click the program to open its does not shown on the screen but when I check with WTM (Windows Task Manager) its shows that is ON and you can only witness the laptop going very slow and I have to reboot it, and I can not install any other Mozilla :( because of the same problem and all the above.
    I really need Mozilla to work as soon as possible due to important deadlines I have pendent, and i can only use Chrome but is not my ideal program. Can you help me , please ?????
    Thank you
    Vitor Mendes

    If it opens in safe mode, you may have a problematic add-on. Try the procedure in the [[Troubleshooting extensions and themes]] article.

Maybe you are looking for