MIB: ifOutDiscards

Hi,
a customer is using the following MIB to monitor a WAN interface
RFC1213-MIB:ifOutDiscards
OID 1.3.6.1.2.1.2.2.1.19
and reports lot of errors to me ...
If I check on the the router I cannot see many output drops on the WAN interface
Could it be that we are facing any kind of IOS bug here as we already know that the 7304 IOS versions are not always teh best :-(
Cisco IOS Software, 7300 Software (C7300-IS-M), Version 12.2(31)SB15, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Thu 26-Mar-09 09:37 by vpernank
ROM: System Bootstrap, Version 12.2(20060713:011624) [balam-EXODUS_WS_MIRZAM_ROMMON_060713 101], DEVELOPMENT SOFTWARE
pchi1036 uptime is 48 weeks, 4 days, 4 hours, 26 minutes
Uptime for this control processor is 48 weeks, 4 days, 4 hours, 26 minutes
System returned to ROM by power-on
System restarted at 06:30:48 UTC Sun Jan 24 2010
System image file is "disk0:c7300-is-mz.122-31.SB15"
cisco 7300 (NSE150) processor (revision F) with 2031615K/65536K bytes of memory.
Processor board ID SCA0737009P
SB-1 CPU at 800Mhz, Implementation 0x401, Rev 0.2, 512KB L2 Cache
4 slot midplane, Version 67.49
GigabitEthernet0 is up, line protocol is up
Hardware is Pinnacle GE, address is 000c.ceeb.3600 (bia 000c.ceeb.3600)
Description: --- Carrier = AT&T Offer = OPT-E-MAN Silver p2pt
MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec,
     reliability 255/255, txload 13/255, rxload 15/255
Encapsulation 802.1Q Virtual LAN, Vlan ID 1., loopback not set
Keepalive set (10 sec)
Full Duplex, 1000Mbps, 1000BaseLX, Auto-negotiation, media type is LX
output flow-control is XON, input flow-control is unsupported
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:00, output never, output hang never
Last clearing of "show interface" counters 1w0d
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 37688
Queueing strategy: Class-based queueing
Output queue: 0/40 (size/max)
30 second input rate 61721000 bits/sec, 10654 packets/sec
30 second output rate 52934000 bits/sec, 9593 packets/sec
     9396223055 packets input, 7054439734060 bytes, 0 no buffer
     Received 0 broadcasts (0 IP multicasts)
     0 runts, 0 giants, 0 throttles
     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
     0 watchdog, 0 multicast, 0 pause input
     8050498041 packets output, 5453913001688 bytes, 0 underruns
     0 output errors, 0 collisions, 0 interface resets
     0 babbles, 0 late collision, 0 deferred
     0 lost carrier, 0 no carrier, 0 PAUSE output
     0 output buffer failures, 0 output buffers swapped out
many thx for any answers
cheers
Uwe

Are you saying the ifOutDiscards value is much larger than the "Total output drops: 37688" seen in "show interface"? If so, one possibility is since ifOutDiscards is a 32-bit number, and you say there're a "lot of errors", so between the time you snmpwalk ifOutDiscards and you run "show interface", it has rolled over (reset to 0, then start incrementing again).

Similar Messages

High receive discards on Sub-Interfaces in Cisco ASA.

Hello Everyone,
Over the past few weeks Solarwinds is reporting high receive discards on two of our subinterfaces created on Cisco ASA. No errors are observed on other subinterfaces. I checked the trunk port interface on the switch for any errors but found none. These errors are visible only under subinterface. What could be the issue?
Regards

I have the same problem too.
I have Cisco ASA 5515 with the next version:
Cisco Adaptive Security Appliance Software Version 9.1(4)
My interface configuration is the next:
PortChannel5 made with Interface GigabitEthernet 0/2 + Interface GigabitEthernet 0/3
Subinterfaces in PortChannel5
Nagios Graphs shows:
- many input discards in virtual subinterfaces
- many output discards in interface Gi0/2 and Gi0/3
- PortChannel5 output discards is the sum of discards in interface Gi0/2 and Gi0/3
if I run the snmpwalk command against the ASA the following results were obtained:
Interface description
[user@FIREWALL01 ~]$ snmpwalk -v 2c -c XXXXXXX 10.255.16.1 | grep ifDescr
IF-MIB::ifDescr.2 = STRING: Adaptive Security Appliance 'asa_mgmt_plane' interface
IF-MIB::ifDescr.3 = STRING: Adaptive Security Appliance 'Internet' interface
IF-MIB::ifDescr.4 = STRING: Adaptive Security Appliance 'LAN_MPLS' interface
IF-MIB::ifDescr.5 = STRING: Adaptive Security Appliance 'GigabitEthernet0/2' interface
IF-MIB::ifDescr.6 = STRING: Adaptive Security Appliance 'GigabitEthernet0/3' interface
IF-MIB::ifDescr.7 = STRING: Adaptive Security Appliance 'stateifha' interface
IF-MIB::ifDescr.8 = STRING: Adaptive Security Appliance 'statelink' interface
IF-MIB::ifDescr.9 = STRING: Adaptive Security Appliance 'Internal-Data0/1' interface
IF-MIB::ifDescr.10 = STRING: Adaptive Security Appliance 'cplane' interface
IF-MIB::ifDescr.11 = STRING: Adaptive Security Appliance 'mgmt_plane_int_tap' interface
IF-MIB::ifDescr.12 = STRING: Adaptive Security Appliance 'management' interface
IF-MIB::ifDescr.13 = STRING: Adaptive Security Appliance 'Virtual254' interface
IF-MIB::ifDescr.14 = STRING: Adaptive Security Appliance 'Port-channel5' interface
IF-MIB::ifDescr.15 = STRING: Adaptive Security Appliance 'VLAN_USGLB_OOB' interface
IF-MIB::ifDescr.16 = STRING: Adaptive Security Appliance 'VLAN_USGLBHSTHYP_MGNT' interface
IF-MIB::ifDescr.17 = STRING: Adaptive Security Appliance 'VLAN_USGLBVRM_OM' interface
IF-MIB::ifDescr.18 = STRING: Adaptive Security Appliance 'VLAN_USGLBVRM_MGNTOM' interface
IF-MIB::ifDescr.19 = STRING: Adaptive Security Appliance 'VLAN_USGLBVRM_MGNT' interface
IF-MIB::ifDescr.20 = STRING: Adaptive Security Appliance 'VLAN_USGLBVRM_SRVF' interface
IF-MIB::ifDescr.21 = STRING: Adaptive Security Appliance 'VLAN_USGLBVRM_SRVB' interface
IF-MIB::ifDescr.22 = STRING: Adaptive Security Appliance 'VLAN_USGLB_DMZ' interface
Input discards
[user@FIREWALL01 ~]$ snmpwalk -v 2c -c xxxxxxxxxx 10.255.16.1 | grep ifInDiscards
IF-MIB::ifInDiscards.2 = Counter32: 0
IF-MIB::ifInDiscards.3 = Counter32: 0
IF-MIB::ifInDiscards.4 = Counter32: 0
IF-MIB::ifInDiscards.5 = Counter32: 0
IF-MIB::ifInDiscards.6 = Counter32: 0
IF-MIB::ifInDiscards.7 = Counter32: 0
IF-MIB::ifInDiscards.8 = Counter32: 0
IF-MIB::ifInDiscards.9 = Counter32: 0
IF-MIB::ifInDiscards.10 = Counter32: 0
IF-MIB::ifInDiscards.11 = Counter32: 0
IF-MIB::ifInDiscards.12 = Counter32: 0
IF-MIB::ifInDiscards.13 = Counter32: 0
IF-MIB::ifInDiscards.14 = Counter32: 0
IF-MIB::ifInDiscards.15 = Counter32: 12481926
IF-MIB::ifInDiscards.16 = Counter32: 9927941
IF-MIB::ifInDiscards.17 = Counter32: 134120211
IF-MIB::ifInDiscards.18 = Counter32: 124695686
IF-MIB::ifInDiscards.19 = Counter32: 27081148
IF-MIB::ifInDiscards.20 = Counter32: 2941537222
IF-MIB::ifInDiscards.21 = Counter32: 32714719
IF-MIB::ifInDiscards.22 = Counter32: 4008856
Output discards
[user@FIREWALL01 ~]$ snmpwalk -v 2c -c xxxxxxxxxxxx 10.255.16.1 | grep ifOutDiscards
IF-MIB::ifOutDiscards.2 = Counter32: 0
IF-MIB::ifOutDiscards.3 = Counter32: 0
IF-MIB::ifOutDiscards.4 = Counter32: 0
IF-MIB::ifOutDiscards.5 = Counter32: 3635696
IF-MIB::ifOutDiscards.6 = Counter32: 119099
IF-MIB::ifOutDiscards.7 = Counter32: 0
IF-MIB::ifOutDiscards.8 = Counter32: 0
IF-MIB::ifOutDiscards.9 = Counter32: 0
IF-MIB::ifOutDiscards.10 = Counter32: 0
IF-MIB::ifOutDiscards.11 = Counter32: 0
IF-MIB::ifOutDiscards.12 = Counter32: 0
IF-MIB::ifOutDiscards.13 = Counter32: 0
IF-MIB::ifOutDiscards.14 = Counter32: 3754795
IF-MIB::ifOutDiscards.15 = Counter32: 0
IF-MIB::ifOutDiscards.16 = Counter32: 0
IF-MIB::ifOutDiscards.17 = Counter32: 0
IF-MIB::ifOutDiscards.18 = Counter32: 0
IF-MIB::ifOutDiscards.19 = Counter32: 0
IF-MIB::ifOutDiscards.20 = Counter32: 0
IF-MIB::ifOutDiscards.21 = Counter32: 0
IF-MIB::ifOutDiscards.22 = Counter32: 0
Output discards may be normals, but I don't understand input discards in virtual subinterfaces of PortChannel5
By the other hand, show interface command in subinterfaces don't show error or discards packets
FIREWALL01/pri/act# sh interface VLAN_USGLBVRM_SRVB detail
Interface Port-channel5.1020 "VLAN_USGLBVRM_SRVB", is up, line protocol is up
Hardware is EtherChannel/LACP, BW 2000 Mbps, DLY 10 usec
VLAN identifier 1020
Description: VLAN_USGLBVRM_SRVB
MAC address 6073.5c69.0917, MTU 1500
IP address 10.255.19.65, subnet mask 255.255.255.192
Traffic Statistics for "VLAN_USGLBVRM_SRVB":
42067433644 packets input, 45125599467459 bytes
28153119062 packets output, 8866514693262 bytes
32715765 packets dropped
Control Point Interface States:
Interface number is 21
Interface config status is active
Interface state is active
Control Point Vlan1020 States:
Interface vlan config status is active
Interface vlan state is UP
FIREWALL01/pri/act# sh interface VLAN_USGLBVRM_SRVF detail
Interface Port-channel5.1019 "VLAN_USGLBVRM_SRVF", is up, line protocol is up
Hardware is EtherChannel/LACP, BW 2000 Mbps, DLY 10 usec
VLAN identifier 1019
Description: VLAN_USGLBVRM_SRVF
MAC address 6073.5c69.0917, MTU 1500
IP address 10.255.19.1, subnet mask 255.255.255.192
Traffic Statistics for "VLAN_USGLBVRM_SRVF":
30475814698 packets input, 14615432248013 bytes
27472348465 packets output, 20872697455933 bytes
2941588838 packets dropped
Control Point Interface States:
Interface number is 20
Interface config status is active
Interface state is active
Control Point Vlan1019 States:
Interface vlan config status is active
Interface vlan state is UP
FIREWALL01/pri/act#
Can anyone explain why so many input errors appear in the subinterfaces?
Thanks in advance!

Unable to collect NIC data for reporting with MIB-II module

Hi all,
Here we have SunMC 3.6.1 set up with almost all the available modules, including the complete "MIB-II Instrumentation" one. We also have the "Performance Reporting Manager" feature, and want to use it to generate a hole bunch of performance reports for our Sun servers.
The problem I am facing is that I try to collect data through the "MIB-II Instrumentation module". I browse into "Interfaces Group", and there I can see all the NICs I have on the system. I would like to record the "If In Octets" and the "If Out Octets" fields. I right-click on these fields, I select the "Attribute Editor", then I click on the "History" Tab, and I choose to save the history on the disk, at each 300 seconds, and the file type is "circular".
Even after waiting for 24 hours, I don't have access to data that should be recorded. If the Performance Report Manager application, when I list the "data availability" for the server where I activated the collect, all I see is the "Kernel Reader" module collects I already activated: I don't see any "MIB-II Instrumentation" module there...
On the "Server details" window, when I go the the "Module management" tab, if I choose "MIB-II Instrumentation" module, it is charged and activated. However, when I click on the "Rules" button, the only ones appearing are the following:
IF Oper Status (1)   rCompare   -   -   -
IF Oper Status (2)   rCompare   -   -   -
IF Oper Status (3)   rCompare   -   -   -
IF Oper Status (4)   rCompare   -   -   -and I find it to be exactly the same for the "MIB-II (Simple)" module... Could it be the reason why I cannot collect the "IF In Octets" and "IF Out Octets" fields?
Is there a way I can collect more relevant statistics about network usage with SunMC, using the "MIB-II Instrumentation" module, or something else within SunMC?
Thanks in advance!!
Ben

Hi Ben,
Is there a way I can collect more relevant statistics
about network usage with SunMC, using the "MIB-II
Instrumentation" module, or something else within
SunMC?It sounds like a general problem with PRM: though if the Data Availability tab shows it's pulling Kernel Reader data every hour, then it should show your MIB-II info as well.
Even then octet counts aren't terribly useful: they're just big numbers that get bigger: you really need to see rates over time to get an idea of what your network is doing.
You could try the SystemMonitor module that's part of PlusPack:
http://www.halcyoninc.com/products/PlusPack/help/SystemMonitor/HALSolarisSystemAlert-network-h.html
It shows MB/minute rates for each interface. If that's the type of info you need then you can enable those numbers for PRM or Reporter instead.
Regards,
[email protected]
http://www.HalcyonInc.com

Need help to find the correct .MIB-file

Hi.
We are using some Nexus 7009 chassis on my work and a program called "SNMPc" that receives traps from our Nexus devices.
The program do not have the new Nexus 7000 MIBs so we are only getting "pure text" from Nexus.
We need to download the right type of MIB file so we can get a better understanding of what is happening on the Nexus.
We can ONLY use ".mib" extensions but Cisco currently only offering ".traps", ".my" and ".oid" files what I can find.
This is an example message we get:
ciscoMgmt.706.0.1 [1] ifName.437260288 (DisplayString): Ethernet3/2 [2] ciscoMgmt.706.1.1.0 (Integer): 5 [3] ciscoMgmt.706.1.2.0 (Integer): 5 [4] ciscoMgmt.706.1.3.0 (Integer): 5 [5] ciscoMgmt.706.1.4.0 (Integer): 5 [6] ciscoMgmt.706.1.5.0 (Integer): 5 [7] ciscoMgmt.706.1.6.0 (Integer): 5 [8] ciscoMgmt.706.1.7.0 (Integer): 5 [9] ciscoMgmt.706.1.8.0 (Integer): 4 [10] ciscoMgmt.706.1.9.0 (Integer): 5 [11] ciscoMgmt.706.1.10.0 (Integer): 5 [12] ciscoMgmt.706.1.11.0 (Integer): 5 [13] snmpTrapEnterprise.0 (ObjectID): ciscoMgmt.706
We can see that the trap name is: 1.3.6.1.4.1.56.12.1.1.0.1
Can someone help me get the right MIB?

Silly question but have your tried changing the file extension of the .my files to .mib ? I typically have to do something like that for net-snmp with Cisco MIB files...
- Be sure to rate all helpful posts

How do i use MIB-2 for writing MIB for my application?

I want to use the existing MIB-2 to write MIB variable for my application. The application is energy metering.So How do i use MIB-2 for writing MIBs for my application?
Santosh Chavan
IIT MADRAS.

For others who do not know what an MIB is, here is link that shows some more information:
http://www.cisco.com/univercd/cc/td/doc/cisintwk/ito_doc/snmp.htm . A quick Google of MIB did not turn up any useful information, but looking for SNMP quickly found this link.
It really turns out that I am not the person to help.
It turns out that I am not the person to help, but I always want to know more as I may have a similar problem later. I know from personal experience that it is easy to use a term commonly in a company or industry but have no one out side of that industry understand. I was asking if that was such a term (hopefully with a little humor). I'm sorry if my joke fell flat.
I hope that you get an answer,
Bob Young
Bob Young - Test Engineer - Lapsed Certified LabVIEW Developer
DISTek Integration, Inc. - NI Alliance Member
mailto:[email protected]

HP LaserJet 500 support on HOST-RESOURCES-MIB

Hi,
We've various HP printer install in our campus. I've tried to enable snmp in one of the HP printer ( e.g. HP LaserJet 500 color M551). Our goal for the HP printer is to have them response the SNMP "hrDeviceDescr" under the HOST-RESOURCES-MIB when our SNMP manager device send a SNMP request to the HP printer. I've make sure our query manager device and the HP printer has the same community string running the same snmp v2. My question is does the HP LaserJet 500 color M551 support HOST-RESOURCES-MIB and how do I turn it on?
Thanks,
Jason

@jmui
‎Thank you for using HP Support Forum. I have brought your issue to the appropriate team within HP. They will likely request information from you in order to look up your case details or product serial number. Please look for a private message from an identified HP contact. Additionally, keep in mind not to publicly post ( serial numbers and case details).
If you are unfamiliar with the Forum's private messaging please click here to learn more.
Thank you,
Omar
I Work for HP

LaserJet 9050n MiB Variable Issue

I'm trying to find out what the MiB variable is for the paper level, I did some searching on the internet, found the list of MiB's for LJ9050mfp, and also LJ9000 Series, also the HP Common Lib, but when use the variable listed in each of these against my printer, I get either a no instance, or it error's out since the variable doesn't exist. I don't need the exact amount of paper, I would just like to see if it's empty or not, or even a percentage would be great. Here is a list of the variables I have tried: consumable-status-capacity-units SCALAR read-only INTEGER 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.10.1.4.0 consumable-status-total-capacity SCALAR read-only INTEGER ( 0..65535 ) 1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.10.1.5.0 prtinputcapacityunit SCALAR read-only INTEGER 1.3.6.1.4.1.11.2.3.9.4.2.2.8.2.1.8.0 prtinputmaxcapacity SCALAR read-only INTEGER 1.3.6.1.4.1.11.2.3.9.4.2.2.8.2.1.9.0 prtinputcurrentlevel SCALAR read-only INTEGER 1.3.6.1.4.1.11.2.3.9.4.2.2.8.2.1.10.0 Someone please help!!! I would like to get this completed!!!!

The HP-LASERJET-COMMON-MIB defines several tray-specific objects which appear to define the media level in the specified tray; for example:
tray2-media-available OBJECT-TYPE
SYNTAX INTEGER(-1..100)
ACCESS read-only
STATUS optional
DESCRIPTION
"Returns a number that indicates how full the input tray
is. If the device can only detect empty / not empty the
device returns -1 for not empty and 0 for empty. If the
device can determine how full the tray is, the device
returns a percentage full from 0% to 100%
Additional information:
LaserJet 4V can only detect empty/not empty tray.
It returns -1 for not empty and 0 for empty."
::= { intray2 2 }
where:
intray2 OBJECT IDENTIFIER ::= { intrays 2 }
intrays OBJECT IDENTIFIER ::= { intray 3 }
intray OBJECT IDENTIFIER ::= { print-engine 3 }
print-engine OBJECT IDENTIFIER ::= { destination-subsystem 1 }
destination-subsystem OBJECT IDENTIFIER ::= { device 4 }
device OBJECT IDENTIFIER ::= { dm 1 }
dm OBJECT IDENTIFIER ::= { netdm 2 }
netdm OBJECT IDENTIFIER ::= { net-peripheral 4 }
net-peripheral OBJECT IDENTIFIER ::= { hpsystem 9 }
hpsystem OBJECT IDENTIFIER ::= { nm 3 }
nm OBJECT IDENTIFIER ::= { hp 2 }
hp OBJECT IDENTIFIER ::= { iso(1) org(3) dod(6) internet(1) private(4) enterprises(1) 11}
which would suggest that the OID for the tray_2 level is:
1.3.6.1.4.1.11.2.3.9.4.2.1.4.1.3.3.2.2
I've no idea whether or not this will provide you with what you need.

How to download MIB for NXOS or platform Nexus 7010 and Nexus 7004

Hello,
I need to monitor my Nexus 7004 and 7010 by my SNMP Agent, but I can't find the way to donload the required MIBs.
For information I'm running the folling images:
bootflash:///n7000-s2-dk9.6.2.6b.bin
bootflash:///n7000-s1-dk9.6.1.5.bin
By advance thanks for the support
Gildas

The module you are running requires a minimum software version of 5.1.
You are currently running 5.0.3 which is why the module is not
recognized.
Below is a link that explains this:
http://www.cisco.com/en/US/prod/collateral/switches/ps9441/ps9402/data_s
heet_c78-605482.html
Product Specification
Table 3 lists the specifications for the Cisco Nexus 7000 32-Port 10 Gigabit Ethernet
Module with XL Option.
Table 3. Product Specifications
Item
Specifications
System
Product compatibility
Supported in all Cisco Nexus 7000 Series chassis
Software compatibility
Cisco NX-OS Software Release 5.1 or later (minimum requirement)
You would need to upgrade you software.
Hope this helps.
Regards
Muhammed M

This is frustrating... trying to import CISCO-ENTITY-SENSOR-MIB

Well, really trying to import CISCO-ENTITY-SENSOR-EXT-MIB in order to process traps from ASA with "snmp-server enable traps entity power-supply-failure" configured. Figures that CISCO-ENTITY-SENSOR-MIB is a prerequisite. After painstakingly loading up the MIB dependencies listed at http://tools.cisco.com/Support/SNMP/do/BrowseMIB.do?local=en&step=2&mibName=CISCO-ENTITY-SENSOR-MIB, it fails at the last juncture with
CISCO-ENTITY-SENSOR-MIB itself:
snmpttconvertmib --in=CISCO-ENTITY-SENSOR-MIB.my --out=/etc/snmp/snmptt.conf.cisco --debug
***** Processing MIB file *****
snmptranslate version: NET-SNMP version: 5.3.1
severity: Normal
File to load is:        ./CISCO-ENTITY-SENSOR-MIB.my
File to APPEND TO:      /etc/snmp/snmptt.conf.cisco
MIBS environment var:   ./CISCO-ENTITY-SENSOR-MIB.my
mib name: CISCO-ENTITY-SENSOR-MIB
Processing MIB:         CISCO-ENTITY-SENSOR-MIB
skipping a TRAP-TYPE / NOTIFICATION-TYPE line - probably an import line.
Line: 631
NOTIFICATION-TYPE: entSensorThresholdNotification
Variables: entSensorThresholdValue entSensorValue
Enterprise: entitySensorMIBNotifications
Looking up via snmptranslate: CISCO-ENTITY-SENSOR-MIB::entSensorThresholdNotification
No log handling enabled - turning on stderr logging
Cannot find module (ENTITY-MIB): At line 27 in ./CISCO-ENTITY-SENSOR-MIB.my
Cannot find module (CISCO-TC): At line 29 in ./CISCO-ENTITY-SENSOR-MIB.my
Cannot find module (CISCO-SMI): At line 31 in ./CISCO-ENTITY-SENSOR-MIB.my
Did not find 'entPhysicalIndex' in module #-1 (./CISCO-ENTITY-SENSOR-MIB.my)
Did not find 'EntPhysicalIndexOrZero' in module #-1 (./CISCO-ENTITY-SENSOR-MIB.my)
Did not find 'ciscoMgmt' in module #-1 (./CISCO-ENTITY-SENSOR-MIB.my)
Unlinked OID in CISCO-ENTITY-SENSOR-MIB: ciscoEntitySensorMIB ::= { ciscoMgmt 91 }
Undefined identifier: ciscoMgmt near line 33 of ./CISCO-ENTITY-SENSOR-MIB.my
Cannot adopt OID in CISCO-ENTITY-SENSOR-MIB: entitySensorMIBConformance ::= { ciscoEntitySensorMIB 3 }
Cannot adopt OID in CISCO-ENTITY-SENSOR-MIB: entitySensorMIBNotificationPrefix ::= { ciscoEntitySensorMIB 2 }
Cannot adopt OID in CISCO-ENTITY-SENSOR-MIB: entitySensorMIBObjects ::= { ciscoEntitySensorMIB 1 }
Cannot adopt OID in CISCO-ENTITY-SENSOR-MIB: entitySensorMIBNotifications ::= { entitySensorMIBNotificationPrefix 0 }
Cannot adopt OID in CISCO-ENTITY-SENSOR-MIB: entSensorValueEntry ::= { entSensorValueTable 1 }
Cannot adopt OID in CISCO-ENTITY-SENSOR-MIB: entitySensorNotifCtrlGlobalGroup ::= { entitySensorMIBGroups 5 }
Cannot adopt OID in CISCO-ENTITY-SENSOR-MIB: entitySensorValueGroupSup1 ::= { entitySensorMIBGroups 4 }
Cannot adopt OID in CISCO-ENTITY-SENSOR-MIB: entitySensorThresholdNotificationGroup ::= { entitySensorMIBGroups 3 }
Cannot adopt OID in CISCO-ENTITY-SENSOR-MIB: entitySensorThresholdGroup ::= { entitySensorMIBGroups 2 }
Cannot adopt OID in CISCO-ENTITY-SENSOR-MIB: entitySensorValueGroup ::= { entitySensorMIBGroups 1 }
Cannot adopt OID in CISCO-ENTITY-SENSOR-MIB: entSensorThresholdTable ::= { entSensorThresholds 1 }
Cannot adopt OID in CISCO-ENTITY-SENSOR-MIB: entSensorMeasuredEntity ::= { entSensorValueEntry 8 }
Cannot adopt OID in CISCO-ENTITY-SENSOR-MIB: entSensorValueUpdateRate ::= { entSensorValueEntry 7 }
Cannot adopt OID in CISCO-ENTITY-SENSOR-MIB: entSensorValueTimeStamp ::= { entSensorValueEntry 6 }
Cannot adopt OID in CISCO-ENTITY-SENSOR-MIB: entSensorStatus ::= { entSensorValueEntry 5 }
Cannot adopt OID in CISCO-ENTITY-SENSOR-MIB: entSensorValue ::= { entSensorValueEntry 4 }
Cannot adopt OID in CISCO-ENTITY-SENSOR-MIB: entSensorPrecision ::= { entSensorValueEntry 3 }
Cannot adopt OID in CISCO-ENTITY-SENSOR-MIB: entSensorScale ::= { entSensorValueEntry 2 }
Cannot adopt OID in CISCO-ENTITY-SENSOR-MIB: entSensorType ::= { entSensorValueEntry 1 }
Cannot adopt OID in CISCO-ENTITY-SENSOR-MIB: entSensorThresholdEntry ::= { entSensorThresholdTable 1 }
Cannot adopt OID in CISCO-ENTITY-SENSOR-MIB: entSensorThreshNotifGlobalEnable ::= { entSensorGlobalObjects 1 }
Cannot adopt OID in CISCO-ENTITY-SENSOR-MIB: ciscoEntitySensorMIB ::= { ciscoMgmt 91 }
Cannot adopt OID in CISCO-ENTITY-SENSOR-MIB: entSensorGlobalObjects ::= { entitySensorMIBObjects 3 }
Cannot adopt OID in CISCO-ENTITY-SENSOR-MIB: entSensorThresholds ::= { entitySensorMIBObjects 2 }
Cannot adopt OID in CISCO-ENTITY-SENSOR-MIB: entSensorValues ::= { entitySensorMIBObjects 1 }
Cannot adopt OID in CISCO-ENTITY-SENSOR-MIB: entSensorThresholdNotificationEnable ::= { entSensorThresholdEntry 6 }
Cannot adopt OID in CISCO-ENTITY-SENSOR-MIB: entSensorThresholdEvaluation ::= { entSensorThresholdEntry 5 }
Cannot adopt OID in CISCO-ENTITY-SENSOR-MIB: entSensorThresholdValue ::= { entSensorThresholdEntry 4 }
Cannot adopt OID in CISCO-ENTITY-SENSOR-MIB: entSensorThresholdRelation ::= { entSensorThresholdEntry 3 }
Cannot adopt OID in CISCO-ENTITY-SENSOR-MIB: entSensorThresholdSeverity ::= { entSensorThresholdEntry 2 }
Cannot adopt OID in CISCO-ENTITY-SENSOR-MIB: entSensorThresholdIndex ::= { entSensorThresholdEntry 1 }
Cannot adopt OID in CISCO-ENTITY-SENSOR-MIB: entSensorThresholdNotification ::= { entitySensorMIBNotifications 1 }
Cannot adopt OID in CISCO-ENTITY-SENSOR-MIB: entSensorValueTable ::= { entSensorValues 1 }
Cannot adopt OID in CISCO-ENTITY-SENSOR-MIB: entitySensorMIBGroups ::= { entitySensorMIBConformance 2 }
Cannot adopt OID in CISCO-ENTITY-SENSOR-MIB: entitySensorMIBCompliances ::= { entitySensorMIBConformance 1 }
Cannot adopt OID in CISCO-ENTITY-SENSOR-MIB: entitySensorMIBComplianceV04 ::= { entitySensorMIBCompliances 4 }
Cannot adopt OID in CISCO-ENTITY-SENSOR-MIB: entitySensorMIBComplianceV03 ::= { entitySensorMIBCompliances 3 }
Cannot adopt OID in CISCO-ENTITY-SENSOR-MIB: entitySensorMIBComplianceV02 ::= { entitySensorMIBCompliances 2 }
Cannot adopt OID in CISCO-ENTITY-SENSOR-MIB: entitySensorMIBComplianceV01 ::= { entitySensorMIBCompliances 1 }
Unknown object identifier: CISCO-ENTITY-SENSOR-MIB::entSensorThresholdNotification
OID:
Done
Total translations:        1
Successful translations:   0
Failed translations:       1
Those three allegedly missing MIBs are right there in the same directory, and have been imported earlier (though some had no "translation"):
ls
CISCO-ENTITY-SENSOR-EXT-MIB.my CISCO-TC.my     RFC-1212.my            SNMPv2-CONF.my SNMPv2-TC-V1SMI.my
CISCO-ENTITY-SENSOR-MIB.my      ENTITY-MIB.my   RFC-1215.my            SNMPv2-SMI.my   v1
CISCO-SMI.my                    RFC1155-SMI.my SNMP-FRAMEWORK-MIB.my SNMPv2-TC.my
snmpttconvertmib --in=CISCO-SMI.my --out=/etc/snmp/snmptt.conf.cisco --debug
***** Processing MIB file *****
snmptranslate version: NET-SNMP version: 5.3.1
severity: Normal
File to load is:        ./CISCO-SMI.my
File to APPEND TO:      /etc/snmp/snmptt.conf.cisco
MIBS environment var:   ./CISCO-SMI.my
mib name: CISCO-SMI
Processing MIB:         CISCO-SMI
Done
Total translations:        0
Successful translations:   0
Failed translations:       0
snmpttconvertmib --in=CISCO-TC.my --out=/etc/snmp/snmptt.conf.cisco --debug
***** Processing MIB file *****
snmptranslate version: NET-SNMP version: 5.3.1
severity: Normal
File to load is:        ./CISCO-TC.my
File to APPEND TO:      /etc/snmp/snmptt.conf.cisco
MIBS environment var:   ./CISCO-TC.my
mib name: CISCO-TC
Processing MIB:         CISCO-TC
Done
Total translations:        0
Successful translations:   0
Failed translations:       0
snmpttconvertmib --in=ENTITY-MIB.my --out=/etc/snmp/snmptt.conf.cisco --debug
***** Processing MIB file *****
snmptranslate version: NET-SNMP version: 5.3.1
severity: Normal
File to load is:        ./ENTITY-MIB.my
File to APPEND TO:      /etc/snmp/snmptt.conf.cisco
MIBS environment var:   ./ENTITY-MIB.my
mib name: ENTITY-MIB
Processing MIB:         ENTITY-MIB
skipping a TRAP-TYPE / NOTIFICATION-TYPE line - probably an import line.
Line: 1142
NOTIFICATION-TYPE: entConfigChange
Enterprise: entityMIBTrapPrefix
Looking up via snmptranslate: ENTITY-MIB::entConfigChange
OID: .1.3.6.1.2.1.47.2.0.1
Done
Total translations:        1
Successful translations:   1
Failed translations:       0
What am I missing?

I've successfully tried to stay clear of this type of thing as much as I could so my response might be silly.
But one of the things I recall was that a 'somemib.my' file needed 'thatothermib', that was actually there in the directory as 'thatothermib.my', just like I downloaded it, but the mibcompiler was smart enough to look for 'thatothermib.mib'.
Not sure if is was referenced in the other mibfile with a specific extension of if it was the compiler trying to stop me.
Never understood how they managed to make something so simple so complicated.
Cheers,
Michel

Does the Catalyst 2960x-48TD support Cisco's IGMP Snooping MIB?

Does the Catalyst 2960x-48TD support Cisco's IGMP Snooping MIB? We have a number of switches from different vendors and have recently begun switching to Cisco's, however unlike the other brands I am unable to audit the IGMP Snooping settings via SNMP. It appears that while the switch supports IGMP Snooping it does not support the CISCO MIB for IGMP Snooping. Is this a known bug and is it fixed in any of the later releases?
Our company is purchasing and deploying C2960X-48TD's and I am tasked with updating our system audit software

Hi Sean,
Nov 21 15:40:42.390: %MCAST-SPSTBY-6-ETRACK_STATS_LIMIT_EXCEEDED: Number of entries in IGMP snooping explicit-tracking statistics has exceeded the maximum limit (32000)
The above log message is written because the number of explicit-tracking statistics entries is bounded to avoid monopolizing of system resources by IGMP/MLD snooping. The explicit-tracking statistics database maximum size is set to the same as that of explicit-tracking limit.
The statistics are split into two banks: permanent and volatile. The statistics entries will be stored permanently (volatile) until the permanent entries threshold is reached, after which the statistics will be stored temporarily up to the database maximum size. When the size of the database exceeds the permanent threshold, a group will be removed on receiving an IGMP/MLD leave. Groups can be removed whether they were installed above or below the permanent threshold. If the number of statistics entries grows beyond the maximum size of the database, then no statistics will be stored for any newly formed groups.
You can disable ip igmp snooping explicit-tracking by the following
1) Configure "no ip igmp snooping explicit-tracking"
2) Configure "ip igmp snooping limit track 0" on global.
3) After ET is disabled, please do a "clear ip igmp snooping statistics".
Here is a reference URL (please make sure you copy and paste the entire link to the browser):
http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/ios/12.2SX/configuration/guide/snooigmp.html#wp1062242
HTH
Luke

What MIBs do I need?

I'm implementing some testing solution.
I need to comunicate via SNMP with CISCO MDS 9148 FC switch
I need to:
Read interfaces status
Set interface down
Set interface up
The question is what MIBs do I need to be able to do mentioned over? I'm using Python + NetSnmp module.
Thanks in advance.

Hi Sergei,
IF-MIB probably contains what you are looking for to manage interfaces but you will need to load some other mibs as well.
http://tools.cisco.com/Support/SNMP/do/BrowseOID.do?objectInput=1.3.6.1.2.1.2.2.1.7&translate=Translate&submitValue=SUBMIT
MIB Loading Order
http://www.cisco.com/en/US/docs/switches/datacenter/mds9000/sw/5_2/technical/reference/mibs_qkref/MIBRef.html#wp84290

Monitor OSPFv3 via SNMP not working - Is OSPFv3 MIB supported?

I need to be able to query the OSPFv3-MIB via SNMP to track the status of OSPFv3.
I have setup a 3945 router in a test lab network and I have configured it in an Ipv6 network with OSPFv3. The router has an active OSPFv3 neighbor and I can use that neighbor to send/receive data (the routing is working fine). However, when I walk the SNMP MIBs I don't get a response for the OSPFv3-MIB. According to the Cisco SNMP Object Navigator this MIB should be located at 1.3.6.1.3.102.*. Below is an example trying to query a particular OID from the OSPFv3 MIB.
C:\>snmpwalk -v 2c -c public 197.16.18.1 1.3.6.1.3.102.1.5.1.8
SNMPv2-SMI::experimental.102.1.5.1.8 = No Such Object available on this agent at this OID
I can walk other parts of the MIB (For example the OSPFv2 MIB) and get responses, so I know the router has SNMP turned on.
Looking at the Cisco IOS Mib Locator tool (http://tools.cisco.com/ITDIT/MIBS/MainServlet?IMAGE_NAME=c3900-universalk9-mz.SPA.152-4.M3.bin) for the current software version I am running (c3900-universalk9-mz.SPA.152-4.M3.bin) on a 3945 router it claims that the OSPFv3 MIB is supported in this image.
Maybe I need to configure something else? Maybe my SW doesn't really support this MIB? Could it be that I have to query the router over Ipv6 to get the OSPFv3-MIB (I have only been trying Ipv4)?

Hi ,
As Vinod suggested , you need to configure the "SNMP CONTEXT"
Configure:
==========
Basic configuration consists of 4 steps:
Configure mapping between VRF name and SNMP context :
snmp-server vrf <vrf_1> context <context_1>
Create community string corresponding to the VRF :
snmp-server community <vrf_1> RW
Define context string
snmp-server context <context_1>
Configure mapping between context and community:
snmp-server community-map <vrf_1> context <context_1>
(optional) Configure snmp server traps for this VRF community
snmp-server host <IP> traps version 2c <vrf_1>
For e.g:
snmp-server vrf miki
context miki_bgp
snmp-server community miki RW
snmp-server context miki_bgp
snmp-server community-map miki context miki_bgp
Hope it will help
Thanks-
Afroz
***Ratings Encourages Contributors ***

How to convert MIBs to snmpwalk output?

Hi,
I need to develop a monitoring module, but have no access to the actual device I need to develop for.
If I had the device's snmpwalk output - I could simulate the device (e.g., with snmposter) and start the development.
Is there a way to convert the device's MIBs (which I do have) to an snmpwalk output?
Any ideas would be welcome.
Ron.

Hi,
Are you trying to convert the device's MIBs to an snmpwalk output using LabVIEW?
There is a 3rd party toolkit that may be helpful in this case, however it is not supported by National Instruments.
I would appreciate it if you can provide more information on your application so that we can understand the issue better.
Regards
Arham H
Applications Engineer
National Instruments

Need Information to Configure MIbs in 5508 Controllers

Hi All,
I Need to Know few informations about Mibs, we are onboarding devices to HP NNM Tool for monitoring purposes. we have 10 wireless controllers.. We need to enable following traps for AP to pull from tool.
for the below traps to be enabled what are all the traps have to be enabled in controller ?? we have 4400 & 5500 series controllers.
I seen WLC -> SNMP -> trap control , lots of option, i need to clarify 2 thigs
1) whether this is the place ( WLC->SNMP->Trap control) where we need to enable traps for the below Alerts.
2) if so, what are all the options need to be enabled for Below traps in (general/Ap/CLient/Security/Auto RF/Mesh)
Waiting for your inputs
SN
Trap
Oid
Sev
Trap Type
1
APAssociated
.1.3.6.1.4.1.14179.2.6.3.7
Normal
Access point Traps
2
APCoverageProfileFailed
.1.3.6.1.4.1.14179.2.6.3.14
Major
Access point Traps
3
APDisassociated
.1.3.6.1.4.1.14179.2.6.3.8
Major
Access point Traps
4
APDown
.1.3.6.1.4.1.14179.2.6.3.6
Critical
Access point Traps
5
APIfDown
.1.3.6.1.4.1.14179.2.6.3.10
Major
Access point Traps
6
APIfUp
.1.3.6.1.4.1.14179.2.6.3.9
Normal
Access point Traps
7
APInterferenceProfileFailed
.1.3.6.1.4.1.14179.2.6.3.13
Major
Access point Traps
8
APLoadProfileFailed
.1.3.6.1.4.1.14179.2.6.3.11
Major
Access point Traps
9
APLoadProfileUpdatedToPass
.1.3.6.1.4.1.14179.2.6.3.37
Normal
Access point Traps
10
APNoiseProfileFailed
.1.3.6.1.4.1.14179.2.6.3.12
Major
Access point Traps
11
APRadioCardRxFailure
.1.3.6.1.4.1.14179.2.6.3.73
Major
Access point Traps
12
APRadioCardRxFailureClear
.1.3.6.1.4.1.14179.2.6.3.74
Normal
Access point Traps
13
APRadioCardTxFailure
.1.3.6.1.4.1.14179.2.6.3.71
Major
Access point Traps
14
APRadioCardTxFailureClear
.1.3.6.1.4.1.14179.2.6.3.72
Normal
Access point Traps
15
APUp
.1.3.6.1.4.1.14179.2.6.3.5
Normal
Access point Traps
16
ApHasNoRadioCards
.1.3.6.1.4.1.14179.2.6.3.60
Major
Access point Traps
17
SensedTemperatureTooHigh
.1.3.6.1.4.1.14179.2.6.3.43
Critical
Access point Traps
18
SensedTemperatureTooLow
.1.3.6.1.4.1.14179.2.6.3.44
Critical
Access point Traps
19
TemperatureSensorFailure
.1.3.6.1.4.1.14179.2.6.3.45
Critical
Access point Traps

I can tell you one thing cause your question is kind of crypto to me.
You can download the whole mib file for the current image running on your controller from the download software section on cisco site.
Also you can use the SNMP Object navigator on cisco site to look for whatever you want.
And if it is urgent open TAC case cause we are responding on best effort.
Please make sure to rate correct answer

MIB in Solaris 8

Hello,
Our servers are currently monitored by a variety of services (HPOV, WUG, Netcool). There is no environmental monitoring currently performed. Environmental would include failed power supplies, hot of non-functioning fans, excessive chassis temp. There's something similar for Cisco like:
traps for environmental problems are:
(config)#snmp-server enable traps envmon ?
fan Enable SNMP envmon fan traps
shutdown Enable SNMP environmental monitor shutdown traps
status Enable SNMP environmental status change traps
supply Enable SNMP environmental monitor supply traps
temperature Enable SNMP environmental monitor temperature traps
The question here's. I know is something in Solaris 8 (MIB) that can trigger or tell us something of that kind of environmental issues, how could we setup or compile a MIB or MIBS so everytime those issues come out, we get a notification email for instance?
Thanks for any time and/or consideration you may have afforded my message

I used a downloaded PPPD from http://playground.sun.com/pppd/index.html with roaring penguin for my DSL connection.
Lee

MIB: ifOutDiscards

Similar Messages

Maybe you are looking for