Missing LV_Create:C in VI IMAQ Create
Hi,
Has anyone seen this error message before?
Of course, the LV RTM and Vision RTM is installed. ( Bundled into the installer )
+++ In God we believe, in Trance we Trust +++
[Hungary]
Solved!
Go to Solution.
Dear Christian_M,
Sorry my duplicate post, this thread is solved.
RTM = Run Time Menu, But I thought of Run Time Engine
+++ In God we believe, in Trance we Trust +++
[Hungary]
Similar Messages
-
Do I need to change Imaq Create VI or related VIs for a 1394a firewire camera?
I have a program to acquire images from a Zeiss axiocam MR2 that has a PCI framegrabber. Now I am trying to acquire images from one of their firewire cameras using the same program (while swapping the dll functions calls specific for the firewire camera) and it crashes every time I try to acquire an image, even while debugging in steps. Is there something intrinsically different with the firewire camera that I need to do differently? I create a 10 frame buffer with IMAQ create, set a ROI in the firewire camera (works no problem), create a pointer to the buffer, and then put the image into the buffer. No problems with the camera containing a framegrabber but the firewire camera crashes every time on acquisiton. Any ideas? Thanks
Ok. I can see that a firewire camera that doesn't conform to the DCAM spec won't work with the IMAQdx driver so I can't take that approach.
What I still am not understanding is why I can't create a buffer using IMAQ create that I can then place images into using the acquisition function supplied by Zeiss. It seems in the example below that in the case where IMAQdx is used to store images in a buffer using IMAQ create.
Then can you tell me why I can't use the following (or similar) code to snap images to the Image buffer or even a 1D array so long as I have a pointer, proper sized array to put the image data, and the array size?
Thanks for your patience while I try to wrap my head around this -
hi gays,
i have two program,
the first one use {IMAQ create} to get a image from USB webcam,
the second one is picture data process which use [Unflatten Pixmap VI] to get a image data from a BMP file.
Now I want to combine this two program, but data format don't match between the output of {IMAQ create} and the input of [Unflatten Pixmap VI].
My LabVIEW version is 2009
What can i do??Do you have VDM? Did you try "Image to array"?
-
Using IMAQ create, set-up, acquire and windraw to save image without color map
Hi,
Attached is my VI (using labview 8.5) and am not sure where it is getting the color info from, but it saves the image as jpeg/bmp/tiff with colormap (confirmed by imread in matlab). Can someone help me save these images without colormap info.
Thanks
Attachments:
HL Grab with two boards and SONY XC55_Images.vi 166 KBHi Maverick269,
I noticed that you posted this question over on the Machine Vision forums as well. That will definitely be a better place to get this question answered, so let's work on the issue over there :
http://forums.ni.com/t5/Machine-Vision/Using-IMAQ-create-set-up-acquire-and-windraw-to-save-image/m-...
In the future it helps us stay organized if we limit each issue to a single thread.
Cheers,
Andy C.
Applications Engineer
National Instruments -
Ich möchte eine USB-Kamera mit einem LabView-Programm steuern. Dafür habe ich vom Hersteller ein Beispielprogramm erhalten. Jetzt bin ich dabei dieses Beispielprogramm nachzuvollziehen. Ich möchte es dann anschließend erweitern. In diesem Programm sind diverse SubVIs enthalten:
- IMAQ Create: An diesem SubVI sind außen folgende Anschlüsse: Bildname, Bildrahmen, Bildtyp
-> wenn ich bei dem Bildrahmen einen Wert größer als 0 eingebe, dann ist mein Ausgabebild verzerrt. Warum?
-> der Bildtyp gibt mir an wie mein Bild dargestellt wird? In welchem Format?
-> wenn ich das SubVI öffne, muss ich dort auch noch die gleichen Werte eingeben, die ich an den Anschlüssen draußen angegeben habe?
Attachments:
LiveCamera_16bit_2.vi 60 KBBeatricePötschick wrote:
-> wenn ich bei dem Bildrahmen einen Wert größer als 0 eingebe, dann ist mein Ausgabebild verzerrt. Warum?
Hi, Beatrice,
You just forgot about alignment. The IMAQ Image stored in the memorty with alignment:
The alignment is 64 bytes (for latest Vision) So, if your image, for example 256x256 and the Borser is zero, then the image already aligned. I will copy gradirent array to with MemMove function:
As you can see Line Width is 256 pixels - same as image width.
With Border = 3 (which is default) situation quite different. Now image with border is not aligned (256+2*3 = 262 bytes), so for each line 58 additional bytes added - so each line aligned to 64 bytes. If you will just copy array in the same way as above, you will see such image:
For proper copy I will add padding to rthe each line:
Now the image is transferred correctly also with default border.
Refer to IMAQ GetImagePixelPtr Example
Hope it helps for understanding,
Andrey.
Attachments:
MoveBlock01.vi 53 KB
MoveBlock02.vi 53 KB -
Error " Data missing for the entry check while creating a new waste code
Hi all, While setting a new Waste code I get the error " Data missing for the entry check, correction:". while filling the NAM- WASTECOCAT - LER item.
This sould look for the catalog's name included in the phrase set but for some reason it doesn't find it giving me this error.
I am changing original Characteristics, phrase set, classes, and value assignment type. Just to have my own estructure with Znames for all of them.
I have also change the enviroment parameter "WAM_PHRSET_WACATLG" with the name of my phrase set.
I have checked everything several times watching for typos or looking for a missing step.
I have even tried including my new Z's characteristics in the classe and living the original SAP_EHS_1024_001_WASTE_CATALOG. (changing the enviroment parameter WAM_PHRSET_WACATLG to SAP_EHS_1024_001_WASTE_CATALOG) and it works.
I will like to change this characteristic by Z_EHS_WA_WASTE_CATALOG
Phrase set to Z_EHS_WA_WASTE_CATALOG.
enviroment parameter WAM_PHRSET_WACATLG= Z_EHS_WA_WASTE_CATALOG
After matching up the master data It should work fine but I might be missing something to get it running ok.
¿Any idea?
Regards,
AlvaroHello Juan Carlos, the value and class that I want to duplicate and doesn't work is for Waste Code, I have also duplicated the one you have displayed (waste pproperties) without any problem.
1.I have duplicated and changed class SAP_EHS_1024_001. to Z_EHS_WA
2. Create a copy of the 5 characteristics included in this class.
SAP_EHS_1024_001_WASTE_CATALOG
SAP_EHS_1024_001_WASTE_CODE
SAP_EHS_1024_001_WA_SUBCATEG
SAP_EHS_1024_001_WA_CATEGORY
SAP_EHS_1024_001_REMARK
change the name by
Z_EHS_WA_WASTE_CATALOG
Z_EHS_WA_WASTE_CODE
Z_EHS_WA_SUBCATEG
Z_EHS_WA_CATEGORY
Z_EHS_WA_REMARK.
I checked the funcion C14K_WASTECATLG_CHECK is in the value of the Z_EHS_WA_WASTE_CODE characteristic
I checked the funcion C14K_WASTECODE_CHECK is in the value of the Z_EHS_WA_WASTE_CATALOG characteristic
3. Create phrase sets for each new category. with same name.
4. Match up the master data.
5. Change the enviroment parameter.to Z_EHS_WA_WASTE_CATALOG
I think I have followed all the steps, but for some reason it doesn't find the catalog
The phrase for the catalog is EWC in english and LER in spanish.
Regards
Alvaro. -
ORA - 00922 Missing or Invalid option error while creating table
I am tryin to create a table with the following syntax
1 CREATE TABLE TEST_FOR_SCRIPT (
2 TEST_A NUMBER NOT NULL
3 ,TEST_B VARCHAR2(30) DEFAULT 'UNDEFINED' NOT NULL
4 )
5* @storage_parms_table_cmn
6 /
@storage_parms_table_cmn
ERROR at line 5:
ORA-00922: missing or invalid option
Here, storage_parms_table_cmn.sql reads like this
tablespace DBK_CMN_DATA
Can anyone please guide me how to overcome this error.What is your Oracle Version?
i can do it exactly what you did without error
sql> CREATE TABLE vd.TEST_FOR_SCRIPT (
2 TEST_A NUMBER NOT NULL
3 ,TEST_B VARCHAR2(30) DEFAULT 'UNDEFINED' NOT NULL
4 )
5 @test1.sql
6 /
Table created.
Cheers
http://fiedizheng.blogspot.com/ -
Xref table is missing when a pdf file is created with acrobat distiller 9.0.0
Hi
I created a pdf file with the new acrobat distiller 9.0.0 and i noticed that the xref table is missing in it.
Whereas the pdf files which created in older version (acrobat distiller 7.0.5) had the xref tables.
As i have written a perl script to open the pdf files (used a ready made module downloaded form cpan.org). The script works fine with all old pdf files but fails when it tries to open the pdf files created with distiller 9.0.0.
Could i know is any thing changed on acrobat distiller 9.0.0 ?
Thanks
Balaji.PDF documents of version 1.5 and higher can contain cross-reference streams. Read the PDF Reference.
-
HCOUNT missing from M&A v3 / IMAQ 1409??
This question is about the differences between the Measurement and Automation tool for the 1408 and that which is installed with the 1409.
On our systems using the 1408, we are using:
M&A Explorer v1.1 Build 51
NI-IMQ software v2.21.
With this setup, on our camera settings we are able to set properties as
follows:
Generic RS-170 camera
left: 12
top: 0
width: 1000
height: 1000
clamp start: 2
clamp stop: 8
HCOUNT: 1023
and these settings ultimately allow us to capture a full 1000x1000 image.
On our new systems which use the 1409 and:
M&A Explorer v3.0.2.3005
NI-IMQ software v2.61.0
30Hz Progressive Scan camera
It seems we can no longer make the approp
riate settings to allow us to capture a full 1000x1000 window (NOT including the clamp). We're limited in our left/top/width/height to 1000. For example if I set Left=0, I can only set Width to 999. Top seems to only go down to 3 and Height then maxs out at 996. There also no longer appears to be a HCOUNT setting available, though I was able to find a pixels per line setting, but it was greyed out. Our problem is that are images now contain the clamp, whereas in the older version we could effectively remove the clamp via settings that no longer seem to be available to use.
Are we missing some key step here with the new version of M&A? Any help you could offer would be greatly appreciated. I can't believe that the new card wouldn't support the same sizes as the old card.I'm answering my own question here based on feedback from National Instruments tech support:
With the 1409 it has a different ICD (camera file) The default image settings for the camera are set up in the ICD file. You can go into the file and make modification if you want to go outside the normal range. The file is located C:\Program Files\National Instruments\NI-IMAQ\Data\RS-170(1409).icd It can be open in notepad and
edited. This is were the max image size is set. -
How can I find a missing pages document with no title created on Ipad
I created a very important pages document on ipad that i didn't save with a title. It vanished when an inapp notification appeared while working with the document. It is not in cloud nor anywhere in my pages library. How can this happen? Please tell me there is a way to recover this file? At the time of the incident I was running the latest version of IOS (7.1.1) and pages (2.2 -1259)
Please help!
Thank youHave you checked to see if there are any file recovery apps available? either in the App Store or elsewhere.
-
IMAQ Create for compressed .avi - cannot open the new file afterwards with IMAQ Open
Hi there,
i hope i'm in the right board.
I recently tried to compress avi-files i collected from various cameras throughout the last years.
At first i used VDub and ffdshow with a FFVH codec - it worked fine as long as i won't try to open the compressed avi using IMAQ Open.
I googled a bit and read a lot in these forums, tried several solutions - none of them worked.
So i gave it a last, let's call it fail-proof, try:
I took the original .avi (uncompressed, openable with IMAQ Open) and used my newly gained knowledge to use LV for the compression work, i chose from IMAQ AVI Get Filter Names the ffdshow Video Codec and built a small read-write for-loop to convert the AVI frame for frame.
All worked fine despite the problem, that i still cannot open the compressed file in IMAQ Open - and i do not know why.
I would be glad to force labview to decode and open the compressed file with a certain codec, but i found no option for this.
Thanks in advance
Markus
P.S.
I'm using LabView 2010 and VAS of 02/2014.Hello Markus,
have you had a look at this:
Writing a Compressed AVI File with the IMAQ Vision Acquisition Software
Compressing avi files-Discussion Forums
Regards,
eletra -
Hi Team,
We are facing issue for availability check. During creation of Production order, the missing part list is not complete and it should show componenet A in the Missing part list. Below is the details:
Production Order quantity: 100 kg
Componenet A required quantity: 100 kg
MMBE Unrestricted qty: 1000 kg
MMBE Reserved Quantity: 2000 kg
So as per above figures component A should come as missing part during availability check. But it is not coming as missing part. Please check and give your inputs.Hello
The results of availability check should NEVER be compared with MMBE. As already mentioned, transaction CO09 is more appropriate.
Also, this issue has been already discussed on hundreds of threads in the past. See some examples below:
Problem with missing parts list during production order creation
issue in committing material for production order
Material Availibility check in Production orders
availability check
order is not released
As it is stated on the The SCN Rules of Engagement you should do some research before opening a thread. Therefore, please use the search tool or even google to search for similar problems before opening a thread.
BR
Caetano -
Missing Number range when trying to create inventory sampling
Hi,
I tried to create an inventory sampling (Transaction MIS1). I selected a Inv.sampling profile and wanted to save the setting. However I get an error message saying:
For object MATBELEG , number range interval does not exist OMBT
Looking at that TCode OMBT i do have set number ranges correctly.
Since there is space between the MATBELEG and teh comma I believe that at some place a MATBELEG is set to blank, where it cannot find any corresponding numberrange.
How can I resolve teh problem??
Thanks fpor your help
Torstennumber ranges are stored in table NRIV object MATBELEG
Number ranges can be transported (but only with big care). it can be done from OMBT menu Interval > transport.
you will get a warning (which should better be an error) because you transport not only the interval, you transport as well the current number and that will screw up your production system.
better have your basis team open production for a short time frame for customizing ( can be done in SCC4 ) and do it directly in PRD. -
Missing channels on mac mini wifi - create network
I'm trying to create a computer-to-computer network. I have a Mac Mini with Lion
Processor 1.83 GHz Intel Core 2 Duo
When I select Create Network from the WiFi (formerly Airport) It allows me to Name the network and choose 40 or 128 WEP but there are no channels in the pulldown.I'm trying to create a computer-to-computer network. I have a Mac Mini with Lion
Processor 1.83 GHz Intel Core 2 Duo
When I select Create Network from the WiFi (formerly Airport) It allows me to Name the network and choose 40 or 128 WEP but there are no channels in the pulldown. -
Missing sequince in creating vendor or customer
hi all
i have created 5 Vendor and 5 customer on my DEV server.
when i check list for vendor or customer. its has created 00 ,01 then missing 2 , 3 , 4. and then creates 05, 06 ,07.
please tell why it is behaving like this.
Regard
ImranHi imran
check in SM13 that may be missing sequence number not updated in database due to update error
check for all history
Regards,
Nitin Salunkhe
Maybe you are looking for
-
I have an ipod Classic 80G. It is a few years old and hasnt been used for a while. I have just tried to sync it to my new Mac and it says theat thei ipod is synced with another itunes account!!! It was orriganally managed through my old pc but as fa
-
What are the default parameters for PER_EVENTS api
Dear Experts, Can you tell us what are the default parameters for PER_EVENTS API.Here below I have pasted the API. procedure create_event (p_validate in BOOLEAN default FALSE ,p_date_start in DATE ,p_type in VARCHAR2 ,p_business_group_id in NUMBER de
-
Grand total on a Percentage calculation
Guys, I have report where i am calculating % active and % inactive aircrafts for two different types. The data is as below Columns : CustomerType Active Active % Inactive Inactive% Total Data : COMMERCIAL 277 38.96 434 61.04 711 CORPORATE 4593 48.42
-
How Can I find SQL Query in Database
Dear Experts, How Can I find SQL Query in Database.
-
Loudspeakers don't work properly
I'm not exactly sure how to describe the problem but it sounds like one of the loudspeakers on my macbook is a tone lower than the other, not sure which one but its noticeable. Anyone know what could be wrong?