Mountain Lion Finder "unresponsive" (Beach balls) when trying to copy large amount of files

Before Mountain Lion, using Lion - transfering 999 files from my compact flash card to my SSD hard drive via a FW800 reader was SO easy. Select all, drag and drop and the transfer would begin immediately.
Now, after upgrading to Mountain Lion, I experience at least 60 seconds of beach balls and an "unresponsive" finder. Sometimes it starts to transfer, sometimes I have to relaunch finder.
I've reset the PRAM (although I didn't hear 4 beeps), the SMC, I did verify and repair disk permissions.
Any thoughts on this?
Thank you,
(Late 2011 15 in MBP)

Scott Oliphant wrote:
iomega, lacie, 500GB, 1TB, etc, seems to be drive independent. I've formatted and started over with several of the drives and same thing. If I copy the files over in smaller chunks (say, 70GB) as opposed to 600GB, the problem does not happen. It's like finder is holding on to some of the info when it puts it's "ghost" on the destination drive before it's copied over and keeping the file locked when it tries to write over it.
This may be a stretch since I have no experience with iomega and no recent experience with LaCie drives, but the different results if transfers are large or small may be a tip-off.
I ran into something similar with Seagate GoFlex drives and the problem was heat. Virtually none of these drives are ventilated properly (i.e, no fans and not much, if any, air flow) and with extended use, they get really hot and start to generate errors. Seagate's solution is to shut the drive down when not actually in use, which doesn't always play nice with Macs. Your drives may use a different technique for temperature control, or maybe none at all. Relatively small data transfers will allow the drives to recover; very large transfers won't, and to make things worse, as the drive heats up, the transfer rate will often slow down because of the errors. That can be seen if you leave Activity Monitor open and watch the transfer rate over time (a method which Seagate tech support said was worthless because Activity Monitor was unreliable and GoFlex drives had no heat problem).
If that's what's wrong, there really isn't any solution except using the smaller chunks of data which you've found works.

Similar Messages

Premiere Pro CC (2014 version) crashes (beach ball) when trying open certain large Projects

Hi,
I'm currently editing for a TV channel using the latest version of Premiere Pro CC and certain projects (it seems to be with ones with a lot of footage) crash when I open it. Basically, it doesn't even load all the footage up, one that crashed just now said it had around 140 files left to load, but the beach ball arrives and I sat there waiting for half an hour and nothing happen, apart from the beach ball spinning.
Now, we're on an high spec iMac 3.5Ghz i, 32GB ram, 512gb Flash Storage, 4GB Geforce Graphics card, so I don't think the issue can be the mac, unless the macs faulty, but seems to work fine, when I create new projects etc.
Also, their workflow uses USB 3.0 drives, could this be the bottle-neck making them crash? That being said I've edited lots off my USB 3.0 drive at home and my desktop is a lot weaker then this iMac.
Any ideas what the issue may be?
Thank you,
Matt

Hi Matt,
Please mention the exact version of Premiere Pro. Assuming you are using 2014 version, please try some steps mentioned below.
1. Clean the media cache files by navigating to /Users/User Name/Library/Application Support/Adobe/Common
2. Check the version of the drivers of your NVidia card. So, go to Apple Menu>System Preferences and check if you have a CUDA Preference pane if it is not there then go to the below link and update the Card to latest drivers.
CUDA Drivers for MAC Archive | NVIDIA
3. Also, please mention if you have any third party plugins used in the project. If yes, then try to update those Plugins or copy and paste those plugins to some other location and Trash them from MediaCore of Premiere Pro. The location of third party plugins is mentioned below.
Startup Drive or MAC HD /Library/Application Support/Adobe/Common/Plug-ins/7.0
Hope it helps.
Regards,
Vinay

Spinny beach ball when i try to import an aiff file (6mins) into idvd 6.0.3

im reading the posts about audio encoding problems with idvd and
i get spinny beach ball when i try to import an aiff file (6mins) into idvd 6.0.3
right after i click the import button. wondering if this is a part of that problem. im not at the encoding phase. actually im trying to make the simplest dvd in the world. 1 picture and 1 song on the main menu-thats it. i have it set to "best quality" so it doesnt encode in the background-so says the idvd help menu. when i click import or drag the song file into the window (tried it many ways) i get infinite spinny beach ball. dont know if im waiting long enough before i force-quit, about 10 mins. didnt think this would be too hard for the machine to do considering im not burning yet, i just opened the program and this is the first thing i tried to do. any help??? i have a intel mini 1.66 with 2 gb ram, 10 gb free on hd, OS 10.4.9, and using a 23gb imovie file for the video. i didnt try plist deleting or reinstall yet because this is the only problem ive had. repaired permissions, checked the drive with disk utility. ran software update, nothing. nada. HELP!!!

i figured it out last night. idvd doesnt like .aiff's on my machine, maybe because its an intel. i converted it to apple lossless and it worked fine, it imported instantly. .mp3 and .m4a fine as well. i dont know why it wont import an .aiff, maybe because its an intel??? dont know. everyu time i try any aiff file on my machine, idvd does the spinny beachball forever. i even tried to reinstall idvd and that didnt work either, so i gave up and converted it to lossless.
to clarify, im just trying to make a simple dvd with my imovie footage, a main menu picture and 1 song to play on the main menu. i wanted to use the .aiff instead converting it to .mp3 because i didnt want to lose any quality. i guess apple lossless is good enough... whatever, just glad it works now. maybe ill be able to burn the dvd sometime this month, and im ready for the problems that will come when i try to do that. from what i hear i have to pack a lunch. everyone is saying ill have to mow my lawn by the time its done. that *** and not looking forward to that.

Finder issues when copying large amount of files to external drive

When copying large amount of data over firewire 800, finder gives me an error that a file is in use and locks the drive up. I have to force eject. When I reopen the drive, there are a bunch of 0kb files sitting in the directory that did not get copied over. This is happens on multiple drives. I've attached a screen shot of what things look like when I reopen the drive after forcing an eject. Sometime I have to relaunch finder to get back up and running correctly. I've repaired permissions for what it's worth.
10.6.8, by the way, 2.93 12-core, 48gb of ram, fully up to date. This has been happening for a long time, just now trying to find a solution

Scott Oliphant wrote:
iomega, lacie, 500GB, 1TB, etc, seems to be drive independent. I've formatted and started over with several of the drives and same thing. If I copy the files over in smaller chunks (say, 70GB) as opposed to 600GB, the problem does not happen. It's like finder is holding on to some of the info when it puts it's "ghost" on the destination drive before it's copied over and keeping the file locked when it tries to write over it.
This may be a stretch since I have no experience with iomega and no recent experience with LaCie drives, but the different results if transfers are large or small may be a tip-off.
I ran into something similar with Seagate GoFlex drives and the problem was heat. Virtually none of these drives are ventilated properly (i.e, no fans and not much, if any, air flow) and with extended use, they get really hot and start to generate errors. Seagate's solution is to shut the drive down when not actually in use, which doesn't always play nice with Macs. Your drives may use a different technique for temperature control, or maybe none at all. Relatively small data transfers will allow the drives to recover; very large transfers won't, and to make things worse, as the drive heats up, the transfer rate will often slow down because of the errors. That can be seen if you leave Activity Monitor open and watch the transfer rate over time (a method which Seagate tech support said was worthless because Activity Monitor was unreliable and GoFlex drives had no heat problem).
If that's what's wrong, there really isn't any solution except using the smaller chunks of data which you've found works.

App store in 10.6.8 beach ball when trying to install Mountain Lion

Hi I'm trying to upgrade from 10.6.8, on my Mac book pro (early 2010) to Mountain lion.
Problem is whenever I try, via App store, the beach ball appears and the App store becomes non responsive.
Any suggestions?
Thanks

Thanks baltwo. I've been on that sight before. It doesn't help.
App Store does not crash so no logs. In task view it is marked as non responsive. No other services apps etc are acting incorrectly.
I've repaired permissions and played with the password chains.
Any other suggestions?

Is it just me, or does mountain lion have more beach balls, longer boot time, and other unexplained weirdness that clears up with a reboot?

I'm having mixed feelings about Mountain Lion. On the one hand, I like some of the features that more closely integrate with my iWhatever. I appreciate having the notes, reminders, imessage, etc that makes it so I can switch from a mobile device to desktop device.
But on the other hand, I see far more beach balls, such as when simply starting Safari. Applications take a long time to initialize as they try to, I'm guessing, sync with iCloud.   I get more application hangs. You know, the ones that leave you dead in the water until you reboot, but then mysteriously vanish for weeks. and boot time is frustrating. I spend far more time waiting for my desktop and applications to initialize and stabilize after a login.
Granted, much of my frustration here is not based in the technical. It's based on "user experience" where I don't normally pay attention when it's working well. It just feels to me that the behaviour of ML is much more similar to windows of the past, where a reboot once or twice a day cured most ills.
Is it just me or does anyone else have similar feelings of disappointment.
thanks!

Hmmmmm... OK y'all have got me thinking.
I normally run disk check and repair, this time it found a number of files and links related to printers and image devices, stuff that isn't likely part of the issue. There were three links, however, related to core graphics. the permissionss were rwxr-xr-x when they should be rwxrwxrwx. I don't think those are involved, but alas they are fixed.
It seems like much of my issues seems to revolve around the mounting/access of resources outside my laptop, be it icloud, nfs server, samba server, etc. RIght at this moment, Finder is hung hard. I tried to force restart it, and in the Force quit menu I now see two Finders. One will kill and restart immediately, one does nothing.   And I can't open a finder window period.
In fact, just before writing this, I was attempting to edit a text document in StarOffice, and StarOffice went to lunch trying to access my samba share. Now before y'all go nuts about any samba server side issues, let me say that while my MBP is having issues accessing my samba shares, none of my other computing devices are. W7 laptop pulls up samba file system as fast as if not faster than it's own local file systems. My other MBP (older core2 duo, but still on mountain lion) does not seem to have any issues. I don't believe it a server side issue.
So I asked myself, what's different on my 2.66 gb i7 MBP?? It just occurred to me that I have one piece of software that's pretty deeply rooted in file system management....   Tuxera NFS.   I see that it has not been updated since updating to Mountain Lion, so I am going to check that out, and will post results.

Spinning Beach Ball When Trying to Login from Screensaver

This has been an ongoing problem for a couple of years on this Mac Pro, through all versions of OS X 10.4.5 or so to the current 10.4.6. I actually get the same sort of thing, without the beach ball, on my MacBook Pro when trying to bring it out of sleep mode.
Using just the Apple Computer Name screensaver (or any other), a couple of times per month, when I hit the mouse or keyboard to login, there'll be a long delay, and then the beach ball of death appears. Nothing happens after that, but if I don't touch anything, the beach ball eventually goes away, but the screensaver never comes back. Move the mouse and the beach ball comes back.
I can ssh into the system and run terminal commands, including TOP and PS, but nothing revealing in those, but admittedly, I am not sure what to be looking for.
The only way to recover the system is to hold the power key and force a reboot. Usually a sudo reboot or shutdown over ssh will kill the system, but today even that wouldn't work.
My theory is that something running has stalled and the login screen can't activate until that stall is cleared or killed, but what's frustrating is I can't figure out what's stalled, assuming that's even a correct theory. Another possibility is maybe a network share that's mounted is hanging things up for some reason.
These intermittent kinds of problems are maddening.
Is there a console log or ssh terminal command that might be revealing in this circumstance?
Any ideas?
Message was edited by: DSA1

Wow, I'd forgotten that this thread was even open. Surprised to see responses. I forgot to subscribe to it, so I missed the recent discussions.
The link posted by dhkumd above has a post that talks about deleting some preference files via terminal. I haven't tried that yet, but it looks like I've found a similar solution (deleting a particular preference file) on my system for the time being:
I found this post on MacRumor's forums: http://forums.macrumors.com/showthread.php?t=541964
SOLUTION: Browse to Home>Library>Preferences and drag com.apple.systempreferences.plist to the desktop.
Caused by a corrupt user preferences file. On restart, you may find user settings have defaulted. Set up as desired.
Seems to have worked for me with short runs of screensaver enabled. I will have to see what happens overnight before I declare the problem solved. This seems a bit safer than using terminal to rm files. Dragging a copy to the desktop preserves a backup, using terminal to rm them does not.

Spinning Beach Ball when trying to install CC

Help, help, help me pleeeeeze? I have job to do before the end of the weekend... I'm getting desperate!
I got the dmg file and tried to use the Creative Cloud Installer to start my free trial, but double clicking on the installer icon only produces a DLOG that says "Initializing Installer" with an empty progress bar and "Retry" and "Cancel" buttons. Neither of which is available, as the cursor turns into a spinning beach ball immediately, and nothing happens.
I have shut down and rebooted; repaired permissions and verified the hard drive. Nothing is working. Here is my system (yes, I know I barely meet the minimum requirements):
OSX Version 10.9.1
Hardware Overview:
Model Name:          MacBook
Model Identifier:          MacBook5,2
Processor Name:          Intel Core 2 Duo
Processor Speed:          2 GHz
Number of Processors:          1
Total Number of Cores:          2
L2 Cache:          3 MB
Memory:          4 GB
Bus Speed:          1.07 GHz
Boot ROM Version:          MB52.0088.B05
SMC Version (system):          1.38f5
NVIDIA GeForce 9400M:
Chipset Model:          NVIDIA GeForce 9400M
Type:          GPU
Bus:          PCI
VRAM (Total):          256 MB
Vendor:          NVIDIA (0x10de)
Device ID:          0x0866
Revision ID:          0x00b1
ROM Revision:          3384
Displays:
ACER X233H:
Resolution:          1920 x 1080 @ 60 Hz
Pixel Depth:          32-Bit Color (ARGB8888)
Display Serial Number:
Main Display:          Yes
Mirror:          Off
Online:          Yes
Rotation:          Supported
Firewall Settings:
Mode:          Allow all incoming connections
Firewall Logging:          Yes
Stealth Mode:          No
Any ideas? Thanks for your input in advance.
Mandolynda
Message was edited by: Mandolynda

Unfortunately, the fix didn't stick. When the CC app told me it needed an update last night, I downloaded the update (because it wouldn't let me run AI unless I did), opened the .dmg file. It opened the DLOG (Initiating) and then wham: spinning beach ball forever. I have already tried:
Activity Monitor & canceled the task
Repaired permissions
Restarted computer
Re-downloaded the CC app
--no good, same outcome
so, I...
Canceled the task in the Activity Monitor
Plugged in the ethernet and turned off the WIFI (which is what fixed it, finally, the FIRST time this happened
Shut down and restarted the computer
Ran the Cleaner program [http://www.adobe.com/support/contact/cscleanertool.html] (uninstalled *every* Adobe program on my computer)
Re-downloaded the CC app and attempted install
--no good, same outcome
Frustrated out of my mind at that point, I shut off the computer and walked away. I don't know how the hell I'm ever going to get any work done! I'm sure not convinced I should buy a subscription at this point. I think I'll have to let my trial expire and just do all my free-lance work at my daytime job! Adobe won't be making any more money from me that way.

ITunes - new iMac freezes & beach balls when trying to sync iPhone 3

I have a new iMac running Lion. When I try to sync my old iPhone 3g, iTunes freezes with the dreaded spinning beach ball for ever! When I do connect the iPhone, iTunes recognizes my phone in the list, but does not ever give me the option to even erase all my old content. Stranger still - when I get tired of the beach ball spinning and disconnect the iphone, the itunes list briefly displays all my iphone content (playlists, etc.) and then goes away. We have successfully synced a very old ipod shuffle (after wiping its contents) to new Imac, so cables, etc are not the issue. we did have to de-authorize all computers to get new Imac going, perhaps a clue? I have backed up the iphone to both an old mac mini (where it still syncs flawlessly) and have migrated data to new imac so I could recover. I am willing to lose iPhone data so I can sync. I am too cheap to buy newer iphone as it still works great.
my thoughts:
1. erase all content on iphone and then try to sync?
2. grumble and get new iphone?

do you guy's fix the problem?

Spinning Beach Ball When Trying To Capture

Upon trying to capture, using a new camcorder (Canon HV20), in the small black window where the capturing footage would appear, it is black, and in the caption area below it says
"Waiting for timecode.
Device must be in VTR when device control is enabled.
Press Esc to abort."
I pressed Esc and got the spinning beach ball. It's been spinning for 5 minutes or so. What do I do? Thanks.

Please give FULL information of your entire system, OS version, QT version, FCE version, computer, drives, how everything's connected, settings on the media and settings used in FCE.

Get beach ball when trying to log in and can't go further

Hey guys/gals, looking for help.
My parents mac mini has locked up. My dad says he was burning cd's and one would not burn. The computer kept trying to read the disk to no avail. He managed to get the disk to eject, the computer rebooted, but when you click on the name at the sign in screen the beach ball shows up and you can't go any farther. I haven't tried to safe boot yet, but I figured I would post this to see if anyone could offer some help. To make matters worse my parents haven't done a backup in quite some time so it's in my best interests to try everything else first. Any help would be appreciated.
P.

Assuming your parents have the Intel Mini, try to boot from the install disc that came with it.
You'll need a wired (USB) keyboard.
When you are stuck at the beach ball, insert the install disc. Force a power off by holding down the power button on the back of the Mini for 5 seconds or more.
Then restart and hold down the C key as soon as the mini makes the startup chime. (You may have to experiment with the timing.) Keep holding down the C key until you see the "gears" spinning.
Once you boot from the install disc, select the keyboard type, but don't proceed any farther. Instead run DiskUtility from the Utilities menu at the top of the screen.
Have DiskUtility "Repair the Disk" and when that is done, have it "Repair Permissions". Hopefully that will be enough to get things working again.

Really long spinning beach balls when trying a video chat

I just migrated from an older Mac to a brand new Mac Pro 2.66. I plugged in my iSight and tried to do a video conference, only to get a spinning beach ball for >1 minute before the video chat commenced.
Later I tried to access my own camera (by clicking on the camera button at the top of my buddy list) and likewise, >1 minute of spinning beach ball, THEN it worked OK.
Going to the Preferences > Video tab, likewise, spinning beach ball.
Any ideas on how to diagnose and fix this?
Already repaired permissions, and tried unplugging/replugging the iSight.

Hi David,
In iChat > Preferences > Video section you should have a drop down to Pick the camera (either Internal or External).
Have you done this ?
By default iChat will use the Firewire one as first choice (to the extent of changing mid chat if connected.
2:52 PM Sunday; November 26, 2006

Spinning Beach Ball when trying to access Oct. and Nov.

I can't quite figure this one out. Every time I try to access Oct. or Nov. 2010 on my ical, I get a spinning beach ball that lasts for 20 minutes. I have tried erasing my ical and replacing it with my MobileMe data, but it still doesn't work. Any thoughts?

Your profile says you are running 10.5.5. Are you up to date at 10.5.8?
Try reseting your sync history: http://docs.info.apple.com/article.html?path=iSync/2.0/en/isc39.html
If the issue still persists follow this article: http://support.apple.com/kb/TS1627
If the issue STILL persists, export out each of your calendars one at a time using File > Export.
Add 1 new calendar to your iCal.
Import each calendar back in one at a time to a new calendar testing after each import to see if the issue persists.
Once all the calendars are re-imported you can delete the extra calendar.
Hope that helps

Mountain lion hung with beach ball upon initial restart

After Installation completed and restarted, the finder came up and hung with beach ball for at least 30 minutes so far - any body else?

yes, same issue, also freeze on grey screen with verbose blablabla i dont understand...

JQuery function stops working when trying to submit large amount of parameters

Hi,
Run CF9 on Windows 2008 R2 Server.
I have a cfm page with multiple dropdowns (some are cfselect) and dynamically generated lists of checkboxes interdependent on each other. I am using JQuery to submit data to cfc functions and to display data.
It was all working fine until we added new company with large number of records. This translated into large URL query string with a lot of parameters submitted for processing. That's when we started to have problems. I noticed when trying to directly submitting URL, if the total number of characters in URL is more than 2114 I get an error status code 302 Redirect and nothing is displayed.
I tried to play with postParametersLimit and postSizeLimit increasing to 1000.0 in neo-runtime.xml and restarting server but, this did not help.
Below is jquery function:
function populateBills(){
   var plID;
   if ($('#planenrolldate_id').val() == undefined)
    plID = $('input[name=planenrolldate_id]').val();
   else
    plID = $('#planenrolldate_id').val();
   var sID = $('#sponsor_id').val();
   var pID = $('#plan_id').val();
   var fromMonth = $('#from_month').val();
   var fromYear = $('#from_year').val();
   var toMonth = $('#to_month').val();
   var toYear = $('#to_year').val();
   $.ajax({
    type:"POST",
    url:"../components/billing/custompremstatus.cfc?method=GetBillsArr&planenrolldate_id=" + plID + "&sponsorid=" + sID + "&fM=" + fromMonth + "&fY=" + fromYear + "&tM=" + toMonth + "&tY=" + toYear,
    dataType: "json",
    success:
     function(data){
      $.each(data, function(index, item) {
       addBillsCheckboxes(item.bill_id,item.bill_period);
    }, //end the error function
    error:
     function(){
      alert("An error has occurred while fetching bills");
     } //end the error function
   }); // end ajax call
} // end of function

That's exactly from the console after I submit:
fM 9
fY 2014
method GetBillsArr
planenrolldate_id[] 564
planenrolldate_id[] 561
sponsor_id 59
tM 9
tY 2014
When I check just one planenrolldate_id then it looks like this
fM 9
fY 2014
method GetBillsArr
planenrolldate_id[] 561
sponsor_id 59
tM 9
tY 2014
This it cfc part:
<cffunction name="GetBillsArr" access="remote" returnFormat="json" returnType="array">
        <cfargument name="sponsor_id" type="any" required="true">
        <cfargument name="planenrolldate_id" type="any" required="true">
        <cfargument name="fM" type="numeric" required="true">
        <cfargument name="fY" type="numeric" required="true">
        <cfargument name="tM" type="numeric" required="true">
        <cfargument name="tY" type="numeric" required="true">
        <cfset var result=ArrayNew(1)>
        <cfset var i = 0>
         <cfif ARGUMENTS.planenrolldate_id EQ "" OR ARGUMENTS.sponsor_id EQ "">
            <cfset LstBills = QueryNew("bill_id, bill_period", "Integer, Varchar")>
        <cfelse>
            <cfquery name="LstBills" ...>
                SELECT bill_id,
                    (Convert(varchar(10),billing_start_date,103) + ' - ' + Convert(varchar(10),billing_end_date,103)) + ' [' + Convert(varchar(6),plan_id) + ']' AS bill_period
                    FROM ...
            </cfquery>
        </cfif>
        <cfloop query="LstBills">
            <cfset returnStruct = StructNew()>
            <cfset returnStruct["bill_id"]= bill_id>
             <cfset returnStruct["bill_period"] = bill_period>
             <cfset ArrayAppend(result,returnStruct) />
        </cfloop>
        <cfreturn result>
</cffunction>

Mountain Lion Finder "unresponsive" (Beach balls) when trying to copy large amount of files

Similar Messages

Maybe you are looking for