MSI 875P and the Ocz Gold VX PC4000

Hi,
I have try my new Ocz Gold VX PC4000 on my Msi 875p FISR. On bios in right that say 2.5v to 3.3v but I can't go over 3.0v. I have try it on another Msi 875p FISR but same thing.
Anyone have an idea?
Thank you.

My memory can handle without trouble and invalidating warranty 3.5v. I can't put my memory at 2-2-2-8 because need 3.3v. I have bought this motherboard because she is the only can support 3.3v without use OCZ DDR Memory booster.
You can watch memory spec at : http://www.ocztechnology.com/products/memory/ocz_el_ddr_pc_4000_gold_vx

Similar Messages

MSI 875P and IDE 3

Hi
I will be powering up my newly built 875P system this Sunday and I would like some help in getting my hard drives connected/drivers installed before I do that please?
I do not have any S-ATA drives at present and I don't want to use RAID, but have two Maxtor ATA133 hard drives and I have the choice of using IDE 1 & IDE 2 which are ATA100 or, I could use IDE 3 which will support my ATA133 drives, though I don't think I would notice much difference if I used either port?
The installation will be a new one with a Windows XP install and, in order to get my computer to boot from the master drive, say on IDE 3, what settings, in what parts of the BIOS should I change/enable/disable before starting the installation?
I am also right in thinking that, after I have made the changes in the BIOS and the XP setup begins, I need to press F6 to install the drivers but as I don't want to use RAID and I have no S-ATA drives right now, what do I need to choose after inserting the motherboard floppy?
Regards
Brave01Heart

Hey,
Well to answer your dilemma, it can be done but might require some trickery. I did some experiments and right now I am running 2 WD2000JB drives on it in RAID-0, but by reading other posts I was able to do the following as a test.
Two Seagate Barracuda IV ATA-100 7200RPM 80GB Drives were used.
I don't know if you can do both at once, but I did one at a time and it worked for me. But I did this with the old 1.5 bios. I don't know if you can with the 1.74b or others but I think you might because I don't think the flashes change the bios version on the actual promise 378 controller.
I put one drive on IDE as cable select. Went into the BIOS and set PROMISE Onboard to AS RAID. Now I save and exit and hit CTRL-F when the Fasttrak Bios tries to load. I choose create array within the Promise BIOS but only choose 1 drive. Then save and exit. Then repeat with the second drive also as cable select. It should allow you to do what you are trying. In fact others who have done the same have reported that it gives a boost in drive transfer rate. like changing from standard IDE on an old 40 conductor cable in DMA mode, and then plugging a promise card with an 80 conductors and going UDMA.
If you get the error where it will not let you select only one drive, you may need to set the drive jumpers differently.
Good Luck! Hope this helps,
MR BREEZE
P4 3.0G 800FSB @ 3.45 G/230(924)FSB
MSI 875P Neo FIS2R Bios v1.74b
Kingston HyperX3500 1GB Dual DDR433
ATi Radeon 9800 Pro 128MB @ 441/371
WD1200JB Primary Drive
Pioneer DVR-105 (unlocked firmware 1.33b)
2xWD2000JB on IDE in RAID-0
Antec TrueControl 550
Sandra MAX3! CPU: 11696
Sandra MAX3! Mem: 5565
3dMark2001SE: 20995
3dMark2003: 6848

I need to silently install the latest Mozilla firefox on Win7 machines, I do not see any .msi available and the /S or -S commands on the setup.exe installer does not work. Does someone know what can I do?

I need the silent install of firefox for image deployment.

For windows 7, you can use the -ms switch. For example, I have a batch file that works great. It contains the following:
@ECHO.
@Echo Installing Firefox
@start /wait "Firefox Setup 3.6.10.exe" -ms
However this does not seem to work well in windows XP. To get it to work in windows XP, I had to remove the spaces from the firefox installer and run the following command:
@start /wait FirefoxSetup3.6.10.exe -ms
If anyone has an easier way to get silent install working under XP (without renaming the firefox installer) please let me know!

Neo 875P and the AGP voltages?

Ok I have the settings as in my signature but i can run the card only at 4x, i dunno why but i suspect the voltages. The 8x should run at 0.8V but in Bios there's only 1.55V and Up does anybody has an idea what's wrong?

mathwizard
The voltage you refer to is Signal voltage
x4 1.5v
x8 0.8v
The connector voltage is the same for both specifications 1.5v
Suspect your problem is driver related
Pete

Cannot open msi clock and msi info

hi i am having some small problems with my
mx440-td8x.. when i open the properties for the card i cant open the options msi information and the msi clock. it says: error when the file f:´WINNITsystem32desk.cpl for the controlpanel was opening. what shal i do to fix it?

Guys,
You could go get the latest nVidia Detonator4 Drivers from the nVidia Website. Then you can delete the file msicpl.dll from your Windows directory.
For the extra features:
Use notepad to make a new file and put in it what I quoted below and then save it with the .reg extension.
Quote
Windows Registry Editor Version 5.00
[HKEY_LOCAL_MACHINESOFTWARENVIDIA CorporationGlobalNVTweak]
"Coolbits"=dword:ffffffff
"NvCplEnableAGPSettingsPage"=dword:00000001
"NvCplEnableAdditionalInfoPage"=dword:00000001
"NvCplEnableClearViewPage"=dword:00000001
Double Click on it and it will make an entry into your registry.
That will open all the extra options in the Detonator4 Drivers including the Core and RAM Speeds for your GF4.
Take Care,
Richard

MSI clock and MSI Info Tab TI 4600

Please Help
Every time I try to select the MSI clock and the MSI info tab under the properties control panel in Windows XP I receive a Run DLL error saying their is a problem with file msicpl.dll. I have resetup my entire PC from fdisk to dowloading new drivers the first thing I loaded was the video card and still same error. The card works fine besides this one problem please help.
I Have a P4 20 gig
512 2100 ddr ram
Asus P4S533 Motherboard
Email me or post please!!!
Thank you ?(

wyles,
Download and install the latest nVidia ForceWare Drivers
Delete the file msicpl.dll from your Windows Directory and the problem will go away.
If you want to be able to have the hidden functions, create a file with notepad and put this in it.
Quote
Windows Registry Editor Version 5.00
[HKEY_LOCAL_MACHINE\SOFTWARE\NVIDIA Corporation\Global\NVTweak]
"Coolbits"=dword:ffffffff
"NvCplEnableHardwarePage"=dword:00000001
"NvCplEnableAGPSettingsPage"=dword:00000001
Save it as agpsetting.reg to your desktop or anywhere you like. Then run it and it will give you all the hidden options from nVidia which include extra Resolution settings for your desktop and overclocking for both the memory and core.
Take Care,
Richard

Survey - For all 875p and 865pe : Would you buy MSI MotherBoards Again???

I dont know if this should be done here in MSI's forum but im really pissed off with these boards and until they fix those MANY BUGS i can only speak badly about them.
All i know is that i have another P4 with the Gigabyte's 8INXP Motherboard (7205 chipset) and it's stable as hell...running for almost a year now, it's much older and yet AGP 8x WORK'S WELL!!
I spent alot of money on this new system and i'm already feeling sorry for it...i was going for an ASUS P4C800 deluxe and that's what i should have done...more money but much more reliable.Should have read the forum before buying my 875p-Neo.
Well give your opinion...
My opinion is...i had never experienced computer chaos until now!!!
So with this image of MSI i will not buy another Motherboard from them.
Leba

Well I have to tell everybody that I Personaly happen to think that MSI Makes The Most Stable Motherboards that I have Ever Used ....I have owned a total of 9 Different MSI Boards over the Years, and I still have 2 Boards in operation in my home right now.....If you see by my signature that My 2'ND System I have running now is the Brand New ABIT IC7-MAX 3, And the Only reason that I purchased the ABIT is because I wanted a System that was going to be a "Shoe In" for the Pentium Prescott as far as the ability to be able to provide enough stable V-Core Voltage, as the ABIT IC7-Max 3 has From the Begining of it's inception was ment to be a Prescott Board (as the IC7-G is really thier i875 Canterwood Board), ABIT says that the New IC7-MAX 3 was built for the Prescott with the Options to provide more Voltage going to the CPU, As it has 4 Phase Power (instead of the usual 3 Phase) it also has the new OTES technology which isolates the Mosfetts and the Output transistors and capasitors with huge Heatsinks and thier own Dedicated Enclosed Fan assembly that blows the hot air off of them and removes it to outside of the Case.....But other then the Fact that this Board is Built for Heavy Overclocking in Mind as I can reach 290 MHZ FSB at a 1:1 Memory Ratio, This board also Cost a Fortune compared to to my MSI Boards ...When this ABIT first Came out it was almost as exspensive as BOTH of my MSI Boards put together !! I am not kidding, This Board was Well over $300 US in Late September, And on top of this All of these model ABIT Boards Needed to go back to the Factory because of a DDR and VTT Voltage Problem ...So Would I by another ABIT product..Absolutely NOT would I buy anothe MSI product, well put it this way , I have the New I865PE-PFISR Extreme Edition On order, And on top of it all I think that MSI Does have the BEST Tech. Support (all you have to do is Call!!) and where are you going to find a Product FORUM that has A better Administration and Moderation Team....Not to mention all of the Great Members that go the Extra Mile in order to Help One Another....You wont Find Better, Just Browse the other Websites..ie ASUS, VIA, AOpen, ABIT, Gigabyte,....All that you see in those sites is a bunch of Ranting and No HELP.........MSI ROCKS............Sean REILLY875

Probems with msi 875p neo Fis2r and network controller driver

Hi guys just wondering if anyone could help me with my msi 875p neo FIS2R and problems with the network controller driver/network card.
I'm running xp on a computer my nextdoor neighbour gave me. I got it working fine with service pack 3 installed but then installed a bunch of windows updates last night and the computer would switch itself off before windows could start. Now I reinstalled xp and unfortunately it does not recognise the network controller/card at all now. I tried installing the intel network controller drivers but it stopped because it said no intel adapter/card was installed/present. Could anyone please help with suggestions? I tried running everest and under newtwork it doesnt list intel network adapters but I'm pretty certain it is. Again any suggestions?
--------[ EVEREST Home Edition (c) 2003-2005 Lavalys, Inc. ]
Computer:
Operating System Microsoft Windows XP Professional
OS Service Pack Service Pack 3
DirectX 4.09.00.0904 (DirectX 9.0c)
Motherboard:
CPU Type Intel Pentium 4, 2800 MHz (14 x 200)
Motherboard Name MSI 875P Neo-FIS2R (MS-6758) (5 PCI, 1 AGP, 4 DDR DIMM, Audio, Gigabit LAN, IEEE-1394)
Motherboard Chipset Intel Canterwood i875P
System Memory 1024 MB (PC3200 DDR SDRAM)
BIOS Type AMI (10/11/04)
Partitions:
C: (NTFS) 238464 MB (200326 MB free)
--------[ DMI ]---------------------------------------------------------------------------------------------------------
[ BIOS ]
BIOS Properties:
Vendor American Megatrends Inc.
Version V2.4
Release Date 10/11/2004
Size 512 KB
Boot Devices Floppy Disk, Hard Disk, CD-ROM, ATAPI ZIP, LS-120
Capabilities Flash BIOS, Shadow BIOS, Selectable Boot, EDD, BBS
Supported Standards DMI, APM, ACPI, ESCD, PnP
Expansion Capabilities ISA, PCI, AGP, USB
[ System ]
System Properties:
Manufacturer MICRO-STAR INC.
Product MS-6758
Version 00C
Serial Number 00000000
Wake-Up Type Modem Ring
[ Motherboard ]
Motherboard Properties:
Manufacturer MICRO-STAR INC.
Product MS-6758
Version 00C
Serial Number 00000000
[ Processors / Intel(R) Pentium(R) 4 Processor ]
Processor Properties:
Manufacturer Intel
Version Intel(R) Pentium(R) 4 Processor
External Clock 200 MHz
Maximum Clock 4000 MHz
Current Clock 2800 MHz
Type Central Processor
Voltage 3.3 V, 2.9 V
Status Enabled
Socket Designation FC-478
Network adapters:
Direct Parallel 5.1.2535.0
WAN Miniport (IP) 5.1.2535.0
WAN Miniport (IP) - Packet Scheduler Miniport 5.1.2535.0
WAN Miniport (L2TP) 5.1.2535.0
WAN Miniport (PPPOE) 5.1.2535.0
WAN Miniport (PPTP) 5.1.2535.0

Quote from: Jack t.N. on 14-November-09, 08:00:05
Clear CMOS with your PSU unplugged from A/C power. Then load "Optimized Defaults" in BIOS and retest.
thanks jimi... jack
will try that and post later if it worked... ive never cleared cmos, this sort of thing is relatively new to me but thanks again

MSI 875P Neo and Bios Version 1.6

I have an MSI 875P LSR Board. It works fine but the system temperature is always running at 50-60 degrees C.
I am running bios version 1.2 and I was wondering if it is worth while to upgrade to version 1.6 as my system is stable. I dont feel really comfortable flashing the bios I am running Windows XP with NTFS partition.

Maesus-how much lower do you feel the "real" temperature is? Would perhaps 10C be a fair estimate? I'm still waiting for my friend to dig out his thermal probe so that I can get an accurate reading. I too am still using bios 1.2(rock stable with excellent game play)but am considering a bios upgrade if I purchase faster memory which I'm not sure that version 1.2 would make full use of.

VooDoo uses the MSI 875P Neo-FIS2R Motherboard

Hello All,
Just check at voodoo.com computers and they are offering the MSI™ 875P Neo-FIS2R as the motherboard in their top of the line PC.
Starting price $4,274.25.
From the postings they seem to have resolved the Bios flashing problem. How was never clear in their postings, but they are pretty confident that it was fixed.
Quote from the main Dude there
“The board is still our #1 choice for the i875 platform.”
I know the…….
“The Truth is Out there”

well just out of interest i punched a few selections
now they dont stop emailing me
Hi Steve,
Thank you for taking the time to submit your latest Luxury F-Class Tower configuration to us on our website. You have made some great choices regarding your next PC purchase, the system you put together looks great. Our next step if you are interested is to fine tune your configuration further with one of our technical experts once we have a better idea of what your needs are. Please do not hesitate to contact my VoodooPC Technical Expert Rahul toll-free at 1-888-708-6636 at your earliest convenience.
What's the Voodoo difference? The Voodoo Allure Paint is standard on the F-Class and is a true automotive finish. We use our own Downdraft Bake Booth and we use professional Sata Spray guns to complete the masterpiece. Voodoo was the first to introduce Automotive finishes to the PC Industry, and we set the standard for many companies. Every F-Class system gives you the full benefit of a full three-year comprehensive parts and labor warranty, which includes two-way shipping and backed up with our Premium version of our Lifetime Upgrade Assurance. Premium Upgrade Assurance gives you the option to upgrade your PC anytime you want, for the life of the PC. With Premium Upgrade Assurance we will cover the cost of shipping both ways on major upgrades (for 3 years), we will cover shipping on parts if you just want to buy parts. If you decide to do a major upgrade we will only charge you for one-hour labor maximum, and we will rebuild the entire machine, we'll update all the drivers and firmware, we will re-cable the machine, and we will reinstall and update the Operating System as if the system were new. If you decide to do a major upgrade we will only charge you for one-hour labor maximum, and we will rebuild the entire machine, we'll update all the drivers and firmware, we will re-cable the machine, and we will reinstall and update the Operating System as if the system were new.
We are also in the business of making high-end gaming machines as many of our satisfied customers are extreme gamers but we have our many customers who generally those who want and appreciate the best quality, craftsman & ultra-reliability money can buy - PERIOD. There are no assembly lines here! Voodoo technicians have industry reputation for squeezing maximum performance from components for maximum power and absolute stability. They handcraft each and every machine we build. They take complete ownership of each system (treating each and every machine they build as if it were there own) from start to finish adding up to 40 man hours for just assembly alone! It takes us a full 35 days to build a system and we never go about making any short-cuts or cut corners - from handpicking the best retail parts direct from the manufacturers (no cheap OEM components or dusty old stock here), careful assembly and world-renowned origami cabling for maximum airflow, softwaring (installing Windows and drivers), rigorous testing (it will NOT leave our facilities unless everything is completely fault free), tweaking for maximum performance & ultra-reliability AND we are perhaps known to have the best open box experience in the market when it arrives at your door. We also offer excellent customer service & support, upgrade Assurance & comprehensive warranty. We are also internationally ISO 9002 certified (which some of our other major competitors are not) and have been in computer business since 1991. Perfection simply cannot be rushed...
If you have any questions or need recommendations regarding your next PC purchase, feel free to give me or my Technical Expert Rahul a toll-free call at the number listed below - we would love to hear from you. Thank you for your interest in a VoodooPC and we look forward to hearing from you soon! Have yourself a great day!
Regards,
Richard Watson
40 hrs to screw together a pc and load windows
wonder if they have any vacancies
one think they still will not give is what i asked for
a final price
nice work and profits if you can get it

Attempting to upgarde itunes and I get an error message looking for "an alternate path to a folder containing 'iTunes.msi' location. I've searched my hard drive and the file doesn't exist. What to do?

Attempting to upgarde itunes and I get an error message looking for "an alternate path to a folder containing 'iTunes.msi' location. I've searched my hard drive and the file doesn't exist. What to do?

This worked...found on a prior discussion:
Download the Windows Installer CleanUp utility from the following page (use one of the links under the "DOWNLOAD LOCATIONS" thingy on the Major Geeks page)...
http://majorgeeks.com/download.php?det=4459
From the link above (near the top of the page)....Under 'download locations' click on 'download@majorgeeks'
To install the utility, doubleclick the msicuu2.exe file you just downloaded and ran.
Now run the utility ("Start > All Programs > Windows Install Clean Up"). In the list of programs that appears in CleanUp, select any iTunes entries and click "Remove", as per the following screenshot:
Restart your computer.
Re-download Itunes (latest version form Itunes website) and install. It worked!

Pre-Order your copy of Tom Clancy's Rainbow Six: Siege to get Beta access and the Gold Weapons Pack.

The number one name in tactical first person shooter action is coming back this fall and promises to be the most action packed instalment in the franchise. This fall on October 13th, Ubisoft will be releasing Tom Clancy’s Rainbow Six: Siege. Pre-order your copy online now to get closed beta access and the Gold Weapons Pack.

Hi there kyle16-
The Rainbow Six franchise has been around for a long time, with some highlights and lowlights over the years, it sounds like Rainbow Six Siege should be one of those highlights, but I can understand wanting to be part of the beta to see how things are. I’m sorry to hear that you’ve had so much trouble receiving your beta code.
Normally, our Gaming-BBY team is very efficient at handling code requests and getting them out to customers very quickly. Based on the response you received, our systems may not have been working properly that day as usually they give you the code in the message back. I was able to locate a code for you and requested that it be emailed as well. I’ve also got some additional information for you, so I’m going to send you a private message myself with that information.
Look for that message soon!
Thanks,
Bill|Senior Social Media Specialist | Best Buy® Corporate
Private Message

HT2305 I downloaded, and have two .msi files and one setupadmin.exe file. I click the latter and nothing happens?

I downloaded 2 updates (download only), and there's two .msi files and one setupadmin.exe file. I click the latter and nothing happens? How am I meant to do install these updates?

Sorry I forgot to mention I was doing this on a PC with Vista (the heading was Windows so I didn't bother to mention this). Anyway by trial and error I found that you can click on the .msi files to install them. The files were downlads of updates to iTunes and iCloud Control Panel.

How do I make Read and Write 10 Gold work with Firefox? I have the latest Firefox 10.0.1 but it keeps saying "Please upgrade your version of Mozilla Firefox. The minimum version supported by Read&Write is version 3.0."

I just loaded Moxilla Firefox on my Windows 7 PC today and tried to use my Read and Write 10 Gold text help software but it just does not seem to work with this browser (works fine on Internet Explorer) as it keeps saying "Please upgrade your version of Mozilla Firefox.
The minimum version supported by Read&Write is version 3.0." but this versions is higher than 3.0!

We have a solution available for anyone needing to run Firefox 10 with Read&Write v10 Gold, please email us directly for this temporary resolution- [email protected]

I lost an .msi file and cannot do updates, how do i fix the file?

I lost an .msi file and cannot do updates to my Itunes system, Apple has not been abe to help, where do i find the .msi file or how do i repair the system? All prior updates to the system have worked, but the latest 10.5.2 will not update due to this lost file.

Try the following steps:
1. Go to Microsoft website to fix install and Unistall problems. Click "Run now" from Fix it to remove all iTunes & related installer files:
http://support.microsoft.com/mats/Program_Install_and_Uninstall
Be aware that Windows Installer CleanUp Utility will not remove the actual program from your computer. However, it will remove the installation files so that you can start the installation, upgrade, or uninstall over.
2. You should remove all instances of iTunes and the rest of the components listed below:
it may be necessary to remove all traces of iTunes, QuickTime, and related software components from your computer before reinstalling iTunes.
Use the Control Panel to uninstall iTunes and related software components in the following order:
iTunes
QuickTime
Apple Software Update
Apple Mobile Device Support
Bonjour
Apple Application Support (iTunes 9 or later)
Follow the instructions from Apple article listed here: http://support.apple.com/kb/HT1923 to remove all components
3. Reboot your computer. Next, download iTunes from here:http://www.apple.com/itunes/download/ and install from scratch

MSI 875P and the Ocz Gold VX PC4000

Similar Messages

Maybe you are looking for